Technica 1000BASE-T1 User manual

1000BASE-T1
SFP MODULE
Manual-Version: 2.0
Hardware-Version: 2.2
USER MANUAL
April 2019

100BASE-T1 MediaConverter_BCM User Manual
2
CONTENT
1GENERAL INFORMATION........................................................................................... 3
1.1 Functionality and Features of the 1000BASE-T1 SFP MODULE ....................... 3
1.2 Warranty and Safety Information ........................................................................ 5
1.3 Declaration of conformity .................................................................................... 6
2HARDWARE INTERFACES .......................................................................................... 7
2.1 Molex Connector................................................................................................... 7
2.2 SFP Socket Connector ......................................................................................... 8
3STARTUP AND CONFIGURATION.............................................................................. 9
3.1 Startup ................................................................................................................... 9
3.2 Self-Configuration................................................................................................. 9
3.3 I2C Interface........................................................................................................ 10
3.3.1 I2C configuration ......................................................................................... 10
3.3.2 I2C map register .......................................................................................... 11
3.3.3 I2C Device addressing and operation ........................................................ 11
3.3.3.1 I2C Current address read ..................................................................... 11
3.3.3.2 Random address read .......................................................................... 12
3.3.3.3 Sequential read ..................................................................................... 13
3.3.3.4 Byte Write .............................................................................................. 14
3.3.3.5 Sequential write .................................................................................... 14
3.3.4 I2C access to the 88Q2112_A0 transceiver .............................................. 15
3.3.4.1 Register description ............................................................................. 15
4ADDITIONAL INFORMATION.................................................................................... 17
5LIST OF FIGURES....................................................................................................... 18
6CHANGELOG ............................................................................................................. 19
7CONTACT................................................................................................................... 20

100BASE-T1 MediaConverter_BCM User Manual
3
1GENERAL INFORMATION
1.1 Functionality and Features of the 1000BASE-T1 SFP
MODULE
Figure 1-1: 1000BASE-T1 SFP MODULE
The Technica Engineering 1000Base-T1 SFP Module fits into a standard Small Form-
factor Pluggable slot.
It uses the SGMII and generates 1000 Mbit/s full-duplex 1000BASE-T1.
It is self-configurating after powerup to Automotive 1000BASE-T1.
Note: SERDES interface is not supported!
Registers of the integrated transceiver are accessible via I2C interface for diagnosis
and reconfiguration.

100BASE-T1 MediaConverter_BCM User Manual
4
General Information:
Power requirement:
3.3 Volt DC +/-0.03 Volt
Size:
68 x 14 x 14 mm
Weight:
0,1 kg
International Protection:
IP 2 0
Operating temperature:
0 to +70 °Celsius
Integrated PHY
88Q2112_A0 from Marvell
LINKS:
The User can download the latest firmware and documentation for the 1000BASE-T1
SFP MODULE here:
https://technica-engineering.de/produkt/1000base-t1-sfp-module/

100BASE-T1 MediaConverter_BCM User Manual
5
1.2 Warranty and Safety Information
Before operating the device, read this manual thoroughly and retain
it for your reference.
The latest documentation for the 1000BASE-T1 SFP MODULE can be
downloaded here:
https://technica-engineering.de/produkt/1000base-t1-sfp-module/
Use the device only as described in this manual.
Use only in dry conditions.
Do not apply power to a damaged device.
Do not open the device. Otherwise warranty will be lost.
This device is designed for engineering purpose only.
Special care has to be taken for operation.
Do not use this device in a series production car.
As this device is likely to be used under rough conditions, warranty is
limited to 1 year.
Manufacturer li
ability for damage caused by using the device is
excluded.

100BASE-T1 MediaConverter_BCM User Manual
6
1.3 Declaration of conformity
Figure 1-2: Declaration of conformity

100BASE-T1 MediaConverter_BCM User Manual
7
2HARDWARE INTERFACES
2.1 Molex Connector
The 1000BASE-T1 line is connected by a Molex connector.
•Molex 0533250260 Header 2.0mm
•Molex 510900200 Housing
•Molex 50212-8000 Crimp Contact
Name
Picture
Part Number
Molex Header 2.0mm 0533250260
Molex Housing 51090-0200
Molex 50212-8000 Crimp Contact 50212-8000
Table 2-1: Parts Molex Connector
Pinning:
Pin
Function
Pin
Function
1
1000BASE-T1 Plus
2
1000BASE-T1 Minus
Table 2-2: Pinning of Molex Connector

100BASE-T1 MediaConverter_BCM User Manual
8
2.2 SFP Socket Connector
Pinning:
Pin
Function
Pin
Function
1
GND
11
GND
2
GND
12
SGMII_RXD_N
3
n.c.
13
SGMII_RXD_P
4
I2C_DAT
14
GND
5
I2C_CLK
15
3.3. Volt
6
GND
16
3.3. Volt
7
n.c.
17
GND
8
GND
18
SGMII_TXD_P
9
n.c.
19
SGMII_TXD_N
10
GND
20
GND
Table 2-3: Pinning of SFP Socket Connector

100BASE-T1 MediaConverter_BCM User Manual
9
3STARTUP AND CONFIGURATION
3.1 Startup
After 3.3 Volt power is applied, the SFP module starts up and self-configures the
88Q2112_A0 transceiver by MDIO interface. This lasts 100ms. Do not apply any I2C
activity on the bus during this time!
3.2 Self-Configuration
The SFP Module configures itself to 1000BASE-T1 after power up. Master-/Slave
Configuration is done according to the DIP switch on the bottom of the device.
To reconfigure the DIP switch the lock has to be opened (see pictures).
ON/right = as Master
OFF/ left = as Slave
Figure
3-1: DIP-Switch

100BASE-T1 MediaConverter_BCM User Manual
10
3.3 I2C Interface
3.3.1 I2C configuration
100ms after power up of the module it can be configured by I2C.
The module operates with fSCL up to 53kHz without requiring clock stretching.
The module may clock stretch with fSCL greater than 53kHz and up to 400 kHz.
The module processor listens as slave on the 7-bit address 0x50.
Note: b1010 000X = 0xA0
Read access beyond address 95 will return 0x00.
The 88Q2112_A0 transceiver can be accessed at I2C slave 7-bit address 0x40.
Note: b1000 000X = 0x80
The 88Q2112_A1 PHY does not support I2C interfaces. However, the microcontroller
acts as a bridge between the host and the PHY. Commands from the Host are
processed by the microcontroller. The microcontroller accesses to the PHY trough
MDIO interface and forwards the information to the Host.
For a complete register map please have a look at the 88Q2112_A1 datasheet (NDA
required).

100BASE-T1 MediaConverter_BCM User Manual
11
3.3.2 I2C map register
Memory Map (read only registers):
Data Bytes
Byte
Number
Comment
0x03
0
Identifier SFP
0x04
1
Ext. Identifier
0x80
2
Connector
0x00, 0x00, 0x00, 0x00
3-6
Transceiver high
0x00, 0x00, 0x00, 0x00
7-10
Transceiver low
0x00
11
Encoding
0x01
12
Bitrate Nominal in 100 MBit
0x00
13
Reserved
0x00
14
Link Length Fiber
0x00
15
Link Length Fiber
0x00
16
Link Length Fiber
0x00
17
Link Length Fiber
0x0A
18
Link Length Copper in meter
0x00
19
Reserved
'T','e','c','h','n','i','c','a',' ','E','n','g','.',
' ',' ',' '
20-35
Vendor Name
0x00
36
Reserved
0x00, 0x00, 0x00
37-39
Vendor ID
'1','0','0','B','A','S','E','-','T','1',' ',' ',' ',
' ',' ',' '
40-55 PartNumber
0x00, 0x00, 0x00, 0x00
56-59
Revision Number
0x00, 0x00, 0x00
60-62
Reserved
0xBC
63
Check Code for Field 0-62
0x00, 0x00
64-65
Options
0x00
66
Bitrate max
0x00
67
Bitrate min
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
68-83
Serial Number String
0x00, 0x00, 0x00, 0x00
84-87
Date Code high
0x00, 0x00, 0x00, 0x00
88-91
Date Code low
0x00, 0x00, 0x00
92-94
Reserved
0x42
95
Check Code Extended for Field 64-94
Table 3-1: Memory map
3.3.3 I2C Device addressing and operation
3.3.3.1 I2C Current address read
The current read operation only requires the device address read word to be sent.
When the acknowledge is received from the SFP module, the current address data
word is serially clocked out.

100BASE-T1 MediaConverter_BCM User Manual
12
Example: Read the current address of the SFP module (b1010000X).
3.3.3.2 Random address read
The random address read requires two operations to perform the read.
Example: Read a random address of the SFP module (b1010000X)
First a write operation to specify the address desired to read:

100BASE-T1 MediaConverter_BCM User Manual
13
Then a read operation to read the previous address specified:
3.3.3.3 Sequential read
The sequential reads are started by either a current word address read or a random
address read. To specify a sequential read, the host responds with an acknowledge
instead of a stop after each data word.
First a write operation to specify the address desired to read:

100BASE-T1 MediaConverter_BCM User Manual
14
Then the read operations:
3.3.3.4 Byte Write
The write operation requires 8-bits of data word address following the device address
write word and acknowledgement.
Example: Byte write operation into the SFP module (b1010000X)
3.3.3.5 Sequential write
The sequential write is started in the same way as a single byte write, but the host
master does not send a stop condition after the first word is clocked in.

100BASE-T1 MediaConverter_BCM User Manual
15
3.3.4 I2C access to the 88Q2112_A0 transceiver
The 88Q2112_A0 PHY listens as slave on the 7-bit address 0x40. Every internal register
of the PHY (16 bits) is accessed by defining the Device Number (1 byte) and the
Register address (2 bytes). The I2C Memory address is mapped as:
Address
Register name
0x00 Device number
0x01 Register_address_MSB
0x02 Register_address_LSB
0x03 PHY_Register_Operation_Status
0x04 PHY_Register_data_MSB
0x05 PHY_Register_data_LSB
Table 3-2: Register addresses
3.3.4.1 Register description
•Device number:
Defines the device number of the register to access
•Register_address_MSB:
Defines the Most significant byte of the register to access
•Register_address_LSB:
Defines the Less Significant Byte of the register to access
•PHY_Register_Operation_Status
oBit 0 – Read Start Condition Flag (Read/Write)
This flag is set by the master after specifying the first 3 bytes of the register
(Devices number, Register_address_MSB and Register_address_LSB) when a
read operation is trigged.
oBit 1 – Read In Progress Flag (Read)
This flag is set by the slave during the reading operation
oBit 2 – Read Operation Done Flag (Read)
This flag is set by the slave when the reading operation is finished. This flag can
be read after triggering the read to ensure that the data has finished reading.

100BASE-T1 MediaConverter_BCM User Manual
16
oBit 3 – Write Start Condition Flag (Read)
This flag is set by the slave when a write operation is trigged.
oBit 4 – Write In Progress Flag (Read)
This flag is set by the slave during the writing operation
oBit 5 – Write Operation Done Flag (Read)
This flag is set by the slave when the writing operation is finished. This flag can
be read after writing the PHY_register_data_LSB to ensure that the data has
finished writing
•PHY_register_data_MSB
When a reading operation, this register contains the MSB of the PHY register. When
a write operation, this register contains the MSB to write in the PHY register
•PHY_register_data_LSB
When a reading operation, this register contains the LSB of the PHY register. When
a write operation, this register contains the LSB to write in the PHY register

100BASE-T1 MediaConverter_BCM User Manual
17
4ADDITIONAL INFORMATION
•The 1000BASE-T1 SFP MODULE is optimized for automotive use. The maximum
cable length for 1000BASE-T1 segments is limited to 15 meters

100BASE-T1 MediaConverter_BCM User Manual
18
5LIST OF FIGURES
Figure 1-1: 100BASE-T1 SFP MODULE ............................................................................. 3
Figure 1-2: Declaration of conformity ............................................................................... 6
Figure 3-1: DIP-Switch ........................................................................................................ 9

100BASE-T1 MediaConverter_BCM User Manual
19
6CHANGELOG
Version
Chapter
Description
Date
1.0
All First release
2.0
All Complete rework of all chapters 25.04.2019

100BASE-T1 MediaConverter_BCM User Manual
20
7CONTACT
If you have any questions regarding this product, please feel free to contact us:
Technica Engineering GmbH
Leopoldstr. 236
80807 München
Germany
Technical support:
[e-mail]
General information:
[e-mail]
Most current user manuals and product information:
https://technica-engineering.de/