Tecnoinox B8FXGN9 User guide

B8FXGN9
FREESTANDING 80LT GAS TILTING BRATT PAN WITH STAINLESS STEEL TANK
ON CLOSED CABINET
313176
CODE
DESCRIPTION
MODEL
06-03-2023 09:08

INSTRUCTION MANUAL
FOR INSTALLATION,
MAINTENANCE AND USE
RECTANGULAR BRATT PANS
GAS TYPE
“B8FXGN9 – B8MFXGN9”
“B8FIGN9 – B8MFIGN9”
“B12FXGN9 – B12MFXGN9”
“B12FIGN9 – B12MFIGN9”

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
2GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
TABLE OF CONTENTS
1GENERAL REMINDERS AND NOTES...............................................................................................4
1.1 Introduction..........................................................................................................................................4
1.2 Simbols and pictograms.......................................................................................................................4
1.3 General reminders ...............................................................................................................................4
1.4 Construction.........................................................................................................................................5
1.5 Laws, technical prescriptions and directives........................................................................................6
1.6 Special requirements for the installation site........................................................................................6
1.7 Technical data .....................................................................................................................................7
1.8 Table-Categories; Gas inlet pressures.................................................................................................8
1.9 Gas data ............................................................................................................................................10
2POSITIONING, INSTALLATION AND MAINTENANCE ...................................................................11
2.1 Positioning .........................................................................................................................................11
2.2 Installation..........................................................................................................................................11
2.2.1 Electrical connections and equipotential bonding ..............................................................................11
2.2.2 Connection to waterworks..................................................................................................................12
2.2.3 Gas connection procedures...............................................................................................................12
2.2.4 Checking the operation of the gas system.........................................................................................13
2.2.5 Control of the gas inlet pressure ........................................................................................................13
2.3 Commissioning and testing................................................................................................................14
2.4 Maintenance of the appliance............................................................................................................14
2.4.1 Periodic maintenance ........................................................................................................................15
2.4.2 Possible failures and their elimination................................................................................................16
3CONVERSION TO OTHER TYPES OF GAS....................................................................................17
3.1 Replacement of injectors for main burners ........................................................................................17
3.2 Regulation of primary air flow ............................................................................................................17
3.3 Replacement of injectors for pilot burner ...........................................................................................17
4USE ...................................................................................................................................................18
4.1 Warnings and hints for user...............................................................................................................18
4.2 Instructions for use ............................................................................................................................18
4.2.1 Switch on, start of cooking and switch off ..........................................................................................19
4.3 Emptying the cooking pan:.................................................................................................................20
4.3.1 Optional by-pass manual tilting of the cooking tank...........................................................................20
5CLEANING AND CARE ....................................................................................................................21
5.1 Cleaning and care of the appliance ...................................................................................................21
5.1.1 Daily cleaning ....................................................................................................................................21
5.2 Special procedures in case of prolonged inactivity ............................................................................21
5.3 Special procedures in case of failures ...............................................................................................21
5.4 How to proceed, if … .........................................................................................................................22
6FIGURES AND DETAILS..................................................................................................................23
6.1 LAYOUT CONNECTIONS B8............................................................................................................23

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
3GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
6.2 LAYOUT CONNECTIONS B12..........................................................................................................24
6.3 FIG. GAS VALVE...............................................................................................................................25
6.4 FIG. MAIN BURNER –PRIMARY AIR REGULATION ......................................................................26
6.5 FIG. PILOT BURNER ........................................................................................................................27
6.6 FIG. GAS VALVE...............................................................................................................................28
6.7 WIRING DIAGRAM............................................................................................................................29
6.8 FIG. CONTROLS...............................................................................................................................30
6.9 FIG. CONTROLS...............................................................................................................................31
6.10 FIG. DETAILS OF COMMANDS........................................................................................................32

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
4GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
1 GENERAL REMINDERS AND NOTES
1.1 INTRODUCTION
The heads of business units, where the unit will be installed, have an obligation, in
accordance with the regulations, read carefully the contents of this manual and read
the operators and maintainers involved for parts that they compete.
This manual includes all the information necessary to ensure that our equipment can be
used properly and safely.
Keep this manual with care, so that it is always available to all users of the machine!
The manufacturer does not assume any responsibility or warranty commitment for
accidents and damage due to non-compliance with the requirements or installation or
maintenance not in accordance with safety standards.
Also applies in case of improper use of the appliance by the operator.
1.2 SIMBOLS AND PICTOGRAMS
NOTES!
Report a recommendation or information deemed of particular importance.
ATTENTION!
Report an operation or a dangerous situation.
ATTENTION!
Report a requirement or an obligation.
ATTENTION!
Report the prohibition of operation.
1.3 GENERAL REMINDERS
−Read the warnings contained in this manual carefully as they provide important information concerning
safety during the installation, use and maintenance of the appliance.
−Keep these instructions carefully!
−Only personnel trained for its specific use should use the equipment.
−Keep the appliance under control during use.
−The appliance should be used only for the purpose for which it has been specifically designed; other uses
are improper and hence dangerous.
−During operation surfaces can become hot and require special operation.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
5GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
−Unplug the appliance in case of failures or improper operation.
−Apply exclusively to a service centre for repairs or maintenance.
−Any important information about the appliance required for technical service is contained in the technical
data plate (see figure “View of appliance”).
−If technical assistance is required, the trouble must be described in as much detail as possible, so that a
service technician will be able to understand the nature of the problem.
−Gloves should be worn to protect the hands during installation and maintenance operations.
Follow the fire prevention regulations very carefully.
-Not used absolutly as frying mode.
-Follow the fire prevention regulations very carefully.
-Never use as a grill or a griddle.
-Never use an empty tank.
-Make sure that the boil does not leave the tank empty
1.4 CONSTRUCTION
−Main structure in steel with adjustable height feet.
−Exterior and top finish entirely made of stainless steel .
−Stainless steel vat lid, with bottom in INOX (AISI 304) in model
−Lid in stainless steel, hinged and spring balanced in all opening positions.
−Heating of the vat by burners in stainless steel, resistent to mechanical stress and thermal shocks.
−Gas is supplied through a multiple thermostatic valve.
−The main burner is lit by means of the pilot .
−Switch off the main burner when the pan is overturning
−Hand tilting of the pan
−Motor tilting pan
−Optional (cod.BAM0010) by-pass motorized tilting.
The appliance is equipped with:
−Thermostatic gas valve.
−Pilot burner ignition button
−Ignition of the pilot burner incorporated in the gas valve
−Control knob for temperature regulation.
−Filling of the pan by means of a tap placed on the front panel.
−Tilting handwheel
−Motorized tilting selector

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
6GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
1.5 LAWS, TECHNICAL PRESCRIPTIONS AND DIRECTIVES
When installing the appliance it is necessary to follow and comply with the following regulations:
−current regulations on the matter;
−any hygienic-sanitary regulations concerning cooking environments;
−municipal and/or territorial building regulations and fire prevention prescriptions;
−standards for the use of combustible gas;
−standards for gas-fired systems utilizing on-tap or liquid petroleum gas;
−standards relating to gas-fired cooking appliances and similar equipment used large-scale catering. Safety
requirements;
−standards relating to gas systems for appliances used in professional kitchens and communal facilities
−the regulations of the gas supply company or agency;
−current accident prevention guidelines;
−electricity board regulations concerning safety;
−the regulations of the electrical power supply company or agency;
−any other local prescriptions.
1.6 SPECIAL REQUIREMENTS FOR THE INSTALLATION SITE
−The appliance belongs to the installation class A1 (no direct connection of a chimney of flue exhaust
system is required), so it is very important for the environment in which it is installed to be well-aired and
provided with all the safety openings prescribed for its power.
−In addition, it is good policy to locate the appliance under an extractor hood so that cooking vapours can
be removed rapidly and continuously.
−The gas supply system must be equipped with a rapid on off tap approved for the purpose.
−Current regulations require the installation of a multiple pole switch between the appliance and the
electrical power supply; the switch must have a contact gap of least 3 mm on each pole.
−This appliance requires one water connection. The line must be fitted with an on-off valve.
The electrical isolating switch and the water shutoff valves must both be located near
to the appliance, within easy reach for the user.
Follow the fire prevention regulations very carefully.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
7GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
1.7 TECHNICAL DATA
B8FXGN9 –B8MFXGN9
B8FIGN9 –B8MFIGN9
B12FXGN9 –B12MFXGN9
B12FIGN9 –B12MFIGN9
TECHNICAL DATA (DIMEMSIONS)
Equipment dim.A
mm
800
1200
Equipment dim.B
mm
900
900
Equipment dim.H
mm
900
900
Equipment dim.H2
mm
1630
1630
TECHNICAL DATA (FUNCTIONALITY)
Pan dimension A
mm
698
1098
Pan dimension B
mm
564
564
Pan dimension H
mm
200
200
Pan area
dm²
39
62
Overvall volume
lt
81
127
Useful volume
lt
60
100
Temperature
°C
45÷295
TECHNICAL DATA (INSTALLATION)
Gas power
kW
20
30
Gas connection
Ø"
3/4"
3/4"
Water pressure
kPa
50÷300
Hot water inlet
Ø"
1/2"
Latent heat emission
W/kW
450
Direct heat emission
W/kW
450
Moisture emission
g/h /kW
630
Sound level
dbA
< 70
M
Electric power
kW
0,2
Voltage/Input (standard)**
V
220-240 V 1N 50/60Hz
Cable connection ***
mm²
3 X 1,5
TECHNICAL DATA (STORAGE/MOVEMENT)
Packaging dim.A
mm
1070
1300
Packaging dim.B
mm
870
1050
Packaging dim.H
mm
1270
1220
Volume
m³
1,215
1,68
Net weight
kg
144
217
Gross weight
kg
169
255
**Verify on data plate - ***Cable for standard tension

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
8GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
1.8 TABLE-CATEGORIES; GAS INLET PRESSURES
APPLIANCE
CATEGORY
PN NOMINAL
MAIN PRESSURE
COUNTRY
I2H
20 mbar
NO
I2EK
20; 25 mbar
NL
II2EK3B/P
20/25, 28-30 mbar
NL
I2E
20 mbar
LU, PL
I3B/P
28-30 mbar
CY, MT, NO, NL
I3B/P
37 mbar
PL
I3+
28-30/37 mbar
LU
II2H3B/P
20, 28-30 mbar
DK, SE, FI, BG, EE, LV, LT, CZ, SI, TR ,
HR, RO
II2H3B/P
20, 50 mbar
AT, CH
II2H3+
20, 28-30/37 mbar
ES, GB, GR, IE, IT, PT, SK
II2E+3+
20/25, 28-30/37 mbar
BE, FR
II2ELL3B/P
20, 50 mbar
DE
II2HS3B/P
25, 28-30 mbar
HU
II2HS3B/P
25, 50 mbar
HU
II2ELs
20; 13 mbar
PL
II1a2H
8, 20 mbar
CH, IT
III1a2H3B/P
8, 20, 28-30 mbar
DK
III1ab2H3B/P
8, 20, 28-30 mbar
SE

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
9GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
1
2
3
4
5
Type of Gas
Pn nominal main Pressure
Operation permissible if pressure is in the range:
Operation non permissible if pressure is lower than:
Operation non permissible if pressure is higher than:
mbar
mbar
mbar
mbar
SECOND FAMILY GASES
G20
20
17÷25
17
25
25
20÷30
20
30
G25
20
17÷25
17
25
25
20÷30
20
30
G25.1
25
20÷30
20
30
G25.3
25
20÷30
20
30
G2.350
13
10÷16
10
16
THIRD FAMILY GASES
G30/G31
28-30
25÷35
25
35
28-30/37
20÷35 / 25÷45
20 / 25
35 / 45
37
25÷45
25
45
50
42,5÷57,5
42,5
57,5

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
10 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
1.9 GAS DATA
B8FXGN9 –B8MFXGN9
B8FIGN9 –B8MFIGN9
B12FXGN9 –B12MFXGN9
B12FIGN9 –B12MFIGN9
Rated heating power
kW
20
30
Reduced power
kW
ON-OFF
ON-OFF
CONSUMPTION
GAS
Pn
G20
20 mbar
m³/h
2,12
3,17
G20
25 mbar
m³/h
2,12
3,17
G25
20 mbar
m³/h
2,46
3,69
G25.1
25 mbar
m³/h
2,46
3,69
G25.3
25 mbar
m³/h
2,46
3,69
G2.350
13 mbar
m³/h
2,94
4,41
G30
28-30 mbar
28-30/37 mbar
37 mbar
50 mbar
kg/h
1,58
2,37
NOZZLES (PILOT)
GAS
Pn
Nr.
G20
20 mbar
Ø 1/100 mm
1x340 (51)
1x415 (51)
G20
25 mbar
Ø 1/100 mm
1x325 (51)
1x390 (51)
G25
20 mbar
Ø 1/100 mm
1x380 (51)
1x450 (51)
G25.1
25 mbar
Ø 1/100 mm
1x360 (51)
1x450 (51)
G25.3
25 mbar
Ø 1/100 mm
1x360 (51)
1x435 (51)
G2.350
13 mbar
Ø 1/100 mm
1x480 (80)
1x590 (80)
G30/G31
28-30 mbar
28-30/37 mbar
Ø 1/100 mm
1x225 (30)
1x280 (30)
G30/G31
37 mbar
Ø 1/100 mm
1x210 (30)
1x260 (30)
G30/G31
50 mbar
Ø 1/100 mm
1x195 (30)
1x245 (30)
PRIMARY AIR DISTANCE
GAS
Pn
H
G20
20 mbar
mm
14
10
G20
25 mbar
mm
14
10
G25
20 mbar
mm
12
10
G25.1
25 mbar
mm
12
12
G25.3
25 mbar
mm
12
10
G2.350
13 mbar
mm
10
10
G30/G31
28-30 mbar
28-30/37 mbar
mm
20
18
G30/G31
37 mbar
mm
20
18
G30/G31
50 mbar
mm
20
15

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
11 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
2 POSITIONING, INSTALLATION AND MAINTENANCE
2.1 POSITIONING
−Remove all the packaging and check that the appliance is in perfect conditions. In case of visible damage,
do not connect the appliance and notify the sales point immediately.
−Remove the PVC protection from the panels.
−Dispose of packaging according to regulations. Generally material is divided according to composition and
should be delivered to the waste disposal service.
−Maintain a distance of 3 cm between the back (chimney) of the appliance and the wall. There are no
particular prescriptions regarding side distances from other appliances or walls, however it is advisable to
leave enough space in case of maintenance and/or repairs. It is advisable to fit a suitable heat insulation if
the appliance is in direct contact with inflammable walls.
−The appliance must stand level. Small differences in level can be eliminated by screwing or unscrewing
the adjustable feet: A significantly uneven or sloping stance can affect the operation of the appliance
adversely.
−The device can be put in place or as a single unit or in series with other equipment.
2.2 INSTALLATION
Only qualified technicians must perform the installation, maintenance and test of the
appliance.
Before connecting any parts of the appliance to supplies, make sure that the latter is
equivalent the requirements stated in the technical data plate, if the appliance has
been designed for these supplies.
2.2.1 ELECTRICAL CONNECTIONS AND EQUIPOTENTIAL BONDING
Warning! : The appliance is supplied to operate according to the power supply indicated on the
data plate.
−As mentioned, the appliance must be connected to the power supply by way of a multiple pole main
isolating switch and protection device that must be proportioned to the power of the appliance (1 mA per
kW of rated power).
−The earthing system must be efficient.
−As this appliance is type X equipment (delivery with power cable and without plug), the other hardware
needed to make the connection to the electrical power supply must be provided by the installer.
−The power cable shall be of the kind described in the paragraph “Technical data" and shall be resistant to
oil (type H05RN-F o H07RN-F).
−
−The appliance must incorporate an equipotential system.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
12 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
−Connect the terminal on the lower left-hand side marked with the international symbol a connector
with a nominal cross section <10 mm2. All the appliances installed and the earth system of the building
shall be connected like this.
ATTENTION!
Cut the tension before to make the connection and/or maintenance .
2.2.2 CONNECTION TO WATERWORKS
−Water inlet pressure must be between 50 and 300 kPa, otherwise install a pressure regulator on the line
before the appliance.
−Install a cut-off valve for each supply on the line before the appliance.
−Water connections are fitted in the lower part on the left-hand side of the appliance.
−Make connections according to regulations currently in force.
2.2.3 GAS CONNECTION PROCEDURES
The choice of the gas piping depends on the diameter required for the type of gas, appliance and installation
and should be performed in conformity with current regulations.
Before making the connection, thoroughly clean the gas tube.
Impurities could affect the operation of the machine.
It is recommended that the installation of a pressure regulator (one for each machine),
to stabilize the pressure of the inlet gas.
The diameter of the connections is shown in "TECNICAL DATA"
The point of connection is shown in the "LAYOUT CONNECTIONS"
The gas feed plant can either be fixed or be disconnected; if flexible pipes are employed they must be made
from stainless material and not be affected by corrosion.
If sealing materials are used for connections, they must be certified and approved for the purpose.
Once the appliance has been connected, carry out a leakage test on all the fittings connecting the appliance to
the plant. It is advisable to use a leakage spray, otherwise treat the parts with a foam that does not produce
corrosion; no bubbles should develop. Carry out the leakage test also on the rapid cut-off valve.
Flames are strictly prohibited for leakage tests!

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
13 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
2.2.4 CHECKING THE OPERATION OF THE GAS SYSTEM
Check that the appliance has been prepared (category and type of gas) equivalent to
the family of gas available on site.
If not, it is necessary to convert the appliance to whatever is available. See the paragraph
“CONVERSION TO OTHER TYPES OF GAS”.
The operation of the appliance with its heating capacity depends on the inlet pressure and the calorific power
of the gas.
The calorific power of of the gas (Hi) can be obtained from the service provider and should correspond to the
following values:
GAS
Hi
G20
34,02 (Mj/m³)
G25 / G25.1 / G25.3
29,25 (Mj/m³)
G2.350
24,49 (Mj/m³)
G30
45,65 (Mj/kg)
2.2.5 CONTROL OF THE GAS INLET PRESSURE
The pressure range (inlet pressure) within which the appliance is allowed to operated is stated in tab. "TABLE-
CATEGORIES; GAS INLET PRESSURE “
The appliance shall not be operated out of the given pressure range. If pressure should
differ from the above, advise the gas board or the company which has installed the system
The supply pressure is measured using a liquid pressure gauge ( e.g. a U-shaped pressure gauge, minimum
definition 0.1 mbar), directly at the inlet pressure intake (FIG.1 "A") on the gas feed pipe (See LAYOUT
CONNECTION).
Before connecting the gauge remove the screw of the inlet pressure intake (FIG.1 "B").
Connect the U manometer and measure the pressure with device functioning.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
14 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
The value measured by the pressure gauge should be in the range of allowable pressure shown in the tab.
"TABLE-CATEGORIES; GAS INLET PRESSURE ".
If the value does not match, request the intervention the gas board or the company
which has installed the system
At the end tighten the screw of the inlet pressure intake.
2.3 COMMISSIONING AND TESTING
−Once all the connections have been made, the appliance and the overall installation must be checked
following the directions given in this manual.
−Check in particular:
−that the protective film has been removed from the external surfaces;
−that the lower front panel removed for the electrical connection of the appliance has been fitted back into
position;
−that connections have been made in accordance with the requirements and directions indicated in this
manual;
−that all safety requirements in current standards, statutory regulations and directives have been met;
−that the water connections are leak-free;
−that the electrical connection has been performed according to standards.
−In addition, check that once the appliance has been installed, the power cord is neither subject to stretch
nor in contact with nor surfaces.
−Now proceed to light the appliance as directed in the instructions for use.
−While the appliance is in use, voltage should not differ from the nominal voltage more than +/- 10%.
−The test report must be completed in full and submitted to the customer who should then sign in
acceptance. With effect from this moment, the appliance is covered by the manufacturer’s warranty.
Check that the flue gas exhaust is not clogged and that they are expelled without any hindrance.
Repeat "CONTROL OF THE GAS INLET PRESSURE" with the machine running.
If you have other machines connected to the main pipe of the gas, although these have to be put into
operation, to perform a correct control of of the pressure of inlet gas.
2.4 MAINTENANCE OF THE APPLIANCE
All maintenance operations shall only be performed by a technically qualified service
centre!
−To ensure correct and safe operation, the appliance must be inspected and serviced at least once a year
only. Maintenance includes also controlling the components and tear of pipes, feeding pipes, electrical
components etc.
−It is advisable to replace worn components during maintenance operations to avoid the need for other
maintenance calls and unexpected failures.
−It is also advisable to apply for a maintenance contract with the customer.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
15 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
2.4.1 PERIODIC MAINTENANCE
Periodic inspection will minimize machine downtime and increase operating efficiency.
FOR THE OPERATOR / FOR THE TECHNICAL SERVICE
GREASING SCREW WITHOUT END
−Turn the tank completely
−Connect a grease fitting to the connection on the lower front on the right side.
−Use the grease nipple 3/4 times.
−Move the tank to an intermediate position
−Use the grease nipple 2/3 times.
−Move the tank (cycle completely overturned and in a horizontal position) 2/3 times.
It is advisable to carry out this operation every three months, or whenever the overturn is tiring or noisy.
FOR THE TECHNICAL SERVICE
At each intervention:
−Close all the panels carefully.
−Keep the inside of the sides, where the components are present, clean and dry.
−Keep wiring and electrical connections in good condition.
CHECKS / ANNUAL INTERVENTIONS
1) Greaseing of the tilting rod bearing.
−Remove the front panel of the machine.
−Connect a grease fitting to the bearing located behind the wall from which the tilt rod comes out.
−Use the grease nipple 2/3 times.
2) Check the panels coupling, they must be perfectly closed with all screws.
3) Check water supply seal (water filling tap).
4) Verification closing terminals of electrical parts connections. Cleaning of electrical parts.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
16 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
2.4.2 POSSIBLE FAILURES AND THEIR ELIMINATION
Only technically qualified service centres can perform the operations described below!
PROBLEM AND POSSIBLE CAUSE
The pilot burner does not light up:
−The ignition plug is not fixed correctly or it is badly connected.
−The piezoelectric igniter is damaged.
−The ignition transformer or the ignition contact are damaged, or the supply voltage is missing
−There is a loss of pressure in gas supply.
−The injector of the pilot burner is clogged or the gas valve is damaged.
The pilot burner turns off when the control knob or the ignition button is released:
−The gas valve knob is not pressed fully;
−The thermocouple is not heated sufficiently by the pilot burner.
−The gas valve is faulty.
−The pilot burner is on but the main burner does not light:
−The thermopile is damaged;
−The working thermostat is damaged;
−Tank out of position or limit switch failure.
−The injector of the main burner is clogged or the gas valve is damaged
−The outlet holes of the gas burner are clogged..
−Loss of pressure in the gas supply.
The heating vat temperature cannot be adjusted :
−The thermostat is faulty.
−
−ACCESS TO COMPONENTS AND OPERATION
Remove power to the unit
To facilitate the accessibility to details is being replaced, remove the front panel, after taking out the knob to
adjust the temperature, the handle of the tap water filling and the control wheel to the reversal of the cooking
vessel.
Spark plug
−Replace the pilot (candle integral with the pilot burner)
Termocouple
−Remove the thermocouple by loosening the fitting of the tap and loosen the closure of the pilot bracket;
replace the thermocouple. Fit the new thermocouple in reverse order.
Thermopile
−Remove the thermopile from the pilot, disconnect the cables from the gas valve. Fit the new thermopile in
the reverse sequence.
Gas valve
−Disconnect the valve to all gas and electric connections.
−Install a new valve in the reverse sequence.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
17 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
3 CONVERSION TO OTHER TYPES OF GAS
THE TRANSFORMATION TO A DIFFERENT TYPE OF GAS MEANS:
the replacement of the main burner nozzles;
primary air adjustment;
the replacement of the 'nozzle on pilot burners;
control inlet pressures
3.1 REPLACEMENT OF INJECTORS FOR MAIN BURNERS
The device must be operated with nozzles provided for its nominal heat input (See.tab. " GAS DATA ").
To access the nozzle remove the front panel bath.
Disconnect and remove the ramp nozzle through the mounting screws.
Use a spanner to unscrew the nozzle SW13 ((FIG. "MAIN BURNER - PRIMARY AIR REGULATION") and
replace it with a suitable one (See.tab. " GAS DATA ").
All nozzles necessary for the various types of gas are contained in a bag provided with
the apparatus. The nozzles are identified by marking of the diameter in 1/100 mm.
Perform a leak test (with leak detection spray or foam NON corrosive solutions) at the
connection point of the ramp to the main copper
3.2 REGULATION OF PRIMARY AIR FLOW
Primary air can be considered correctly adjusted if no flame lift is ensured when the burner is cold and the
injector lights when the burner is hot..
The distance “H” (FIG.” MAIN BURNER - PRIMARY AIR REGULATION “) recommended for primary air
regulation is indicated in table ” GAS DATA”.
3.3 REPLACEMENT OF INJECTORS FOR PILOT BURNER
To access the pilot nozzle to remove the front panel bath.
Loosen the locking screw and replace the nozzle with the appropriate one. (See .tab. " GAS DATA ").
AT THE END:
Execute the control inlet pressures as described " CONTROL OF THE GAS INLET PRESSURE "

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
18 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
4 USE
4.1 WARNINGS AND HINTS FOR USER
−This manual contains all the instructions required for a proper and safe use of our appliances.
−Keep the manual in a safe place for future consultation!
−This appliance is for catering use, hence they must be used only by trained kitchen staff.
−The appliance must always be kept under control during use.
−Warning! : The manufacturer shall not be held responsible for injuries or damage due to the non-
compliance with safety rules or an improper use of the appliance by the operator.
−Some improper operating conditions may even be caused by an improper use of the appliance, therefore it
is important to train personnel properly.
−All the installation and maintenance operations must be performed by fitters who are members of
an official register.
−Respect the periods required for maintenance. With this is mind, customers are recommended to sign a
service agreement.
−In case of failures concerning the appliance, all outputs (electrical power supply and water) must be cut off
instantly.
−In case of recurrent failures, contact a service technician.
4.2 INSTRUCTIONS FOR USE
−Before cooking with the appliance for the first time, wash the interior of the cooking vat thoroughly.
WARNING! :
Fill the cooking vat up to a maximum of 40 mm under the overflow border, according to
the maximum level mark, including the food to be cooked.
WARNING! :
Loading water in the vessel through the faucet, make sure there is not hot oil in the
vessel.
WARNING! :
When opening the cover, wear personal protective equipment (gloves type
athermal).
Danger of burns!

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01
19 GB
RECTANGULAR BRATT PANS GAS TYPE “BR8G080I - BR8G080I.M” “BR9G090I –
BR9G090I.M” “BR1G120I – BR1G120I.M” “BR1G150I – BR1G150I.M” “BR1G160I –
BR1G160I.M” “BR1G200I – BR1G200I.M”
4.2.1 SWITCH ON, START OF COOKING AND SWITCH OFF
−Here is a list of the procedures for a safe and correct use of the appliance.
−Open the gas valve located upstream of the appliance.
Pilot burner lighting
−Starting from position “⚫” press the gas-valve knob and turn leftwards to position “ “ ; keep the gas-
valve knob pressed . In the electric ignition is automatically switched on, while in the press the pilot burner
ignition button repeatedly. Keep the valve knob pressed for a few seconds after switching on.
−Release the gas-valve knob and control if the pilot burner is lit.
−Repeat the operation if the flame turns off.
In the event of ignition spark plug failure or power failure, pilot lighting can be done
manually through the peephole on the front panel of the machine.
Start cooking - Main burner ignition and temperature regulation
−Once the pilot burner has been lit, turn the gas-valve knob towards right to the positon “ “.
−Turn the thermostat knob (on the gas-valve knob) from the position “0” to the desired temperature between
45° and 295°, and that causes the automatic ignition of main burners.
−The regulation of the thermostat causes the automatic ignition and extinction of the main burner (ON/OFF
regulation); only the pilot flame is lit.
−When the throttle valve knob is turned to the right to position “ “, the main burner is constantly switched
off.
End cooking - Turning the pilot burner off
−Press gas-valve knob and turn to position “⚫” to turn off the pilot burner and prevent the main burner
from lighting.