Tecnoinox B8FXEN9 User guide

B8FXEN9
FREESTANDING 80LT ELECTRIC TILTING BRAT T PAN WITH STAINLESS STEEL
TANK ON CLOS ED CABINET
316192
CODE
DESCRIPTION
MODEL
06-03-2023 12:06

INSTRUCTION MANUAL
FOR INSTALLATION,
MAINTENANCE AND USE
RECTANGULAR BRATT PANS
ELECTRIC TYPE
“B8FXEN9 - B8MFXEN9”
“B8FIEN9 - B8MFIEN9”
“B12FXEN9 - B12MFXEN9”
“B12FIEN9 - B12MFIEN9”

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
2GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
TABLE OF CONTENTS
1GENERAL REMINDERS AND NOTES...............................................................................................3
1.1 Introduction..........................................................................................................................................3
1.2 Simbols and pictograms.......................................................................................................................3
1.3 General reminders ...............................................................................................................................3
1.4 Construction.........................................................................................................................................4
1.5 Laws, technical prescriptions and directives........................................................................................4
1.6 Special requirements for the installation site........................................................................................5
1.7 Technical data .....................................................................................................................................6
1.8 Electrical specifications (non standard voltages) .................................................................................7
2POSITIONING, INSTALLATION AND MAINTENANCE .....................................................................8
2.1 Positioning ...........................................................................................................................................8
2.2 Installation............................................................................................................................................8
2.2.1 Electrical connections and equipotential bonding ................................................................................8
2.2.2 Connection to waterworks....................................................................................................................9
2.3 Commissioning and testing..................................................................................................................9
2.4 Maintenance of the appliance............................................................................................................10
2.4.1 Periodic maintenance ........................................................................................................................10
2.4.2 Possible failures and their elimination................................................................................................11
3USE ...................................................................................................................................................15
3.1 Warnings and hints for user...............................................................................................................15
3.2 Instructions for use ............................................................................................................................15
3.2.1 Switching on, start cooking ................................................................................................................16
3.3 Emptying the cooking pan:.................................................................................................................17
3.3.1 Optional by-pass manual tilting of the cooking tank...........................................................................17
4CLEANING AND CARE ....................................................................................................................18
4.1 Cleaning and care of the appliance ...................................................................................................18
4.1.1 Daily cleaning ....................................................................................................................................18
4.2 Special procedures in case of prolonged inactivity ............................................................................18
4.3 Special procedures in case of failures ...............................................................................................18
4.4 How to proceed, if … .........................................................................................................................19
5FIGURES AND DETAILS..................................................................................................................20
5.1 LAYOUT CONNECTIONS B8...........................................................................................................20
5.2 LAYOUT CONNECTIONS B12.........................................................................................................21
5.3 FIG. CONTROLS...............................................................................................................................22
5.4 FIG. CONTROLS...............................................................................................................................23
5.5 FIG. DETAILS OF COMMANDS........................................................................................................24

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
3GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
1 GENERAL REMINDERS AND NOTES
1.1 INTRODUCTION
The heads of business units, where the unit will be installed, have an obligation, in
accordance with the regulations, read carefully the contents of this manual and read
the operators and maintainers involved for parts that they compete.
This manual includes all the information necessary to ensure that our equipment can be
used properly and safely.
Keep this manual with care, so that it is always available to all users of the machine!
The manufacturer does not assume any responsibility or warranty commitment for
accidents and damage due to non-compliance with the requirements or installation or
maintenance not in accordance with safety standards.
Also applies in case of improper use of the appliance by the operator.
1.2 SIMBOLS AND PICTOGRAMS
NOTES!
Report a recommendation or information deemed of particular importance.
ATTENTION!
Report an operation or a dangerous situation.
ATTENTION!
Report a requirement or an obligation.
ATTENTION!
Report the prohibition of operation.
1.3 GENERAL REMINDERS
−Read the warnings contained in this manual carefully as they provide important information concerning
safety during the installation, use and maintenance of the appliance.
−Keep these instructions carefully!
−Only personnel trained for its specific use should use the equipment.
−Keep the appliance under control during use.
−The appliance should be used only for the purpose for which it has been specifically designed; other uses
are improper and hence dangerous.
−During operation surfaces can become hot and require special operation.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
4GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
−Unplug the appliance in case of failures or improper operation.
−Apply exclusively to a service centre for repairs or maintenance.
−Any important information about the appliance required for technical service is contained in the technical
data plate (see figure “View of appliance”).
−If technical assistance is required, the trouble must be described in as much detail as possible, so that a
service technician will be able to understand the nature of the problem.
−Gloves should be worn to protect the hands during installation and maintenance operations.
Follow the fire prevention regulations very carefully.
Not used absolutely as frying mode.
Follow the fire prevention regulations very carefully.
Never use as a grill or a griddle.
Never use an empty tank.
Make sure that the boil does not leave the tank empty
1.4 CONSTRUCTION
−Main structure in steel with adjustable height feet.
−Exterior and top finish entirely made of stainless steel .
−Stainless steel vat lid, with bottom in INOX (AISI 304).
−Lid in stainless steel, hinged and spring balanced in all opening positions.
−Heating of the pan by means of heating elements fitted to the bottom of the pan.
−Hand tilting of the pan
−Motor tilting pan.
−Optional (cod.BAM0010) by-pass motorized tilting
The appliance is equipped with:
−Temperature regulation is possible between 45° and 295°C by means of a thermostat fitted to the switch.
−A green signal lamp lights when the appliance is on.
−An orange signal lamp lights when one of the heating elements is on.
−Filling of the pan by means of a tap placed on the front panel.
−Tilting handwheel Motorized tilting selector
−A safety thermostat cuts off power supply automatically in case of failure (eg. breaking of thermostat ).
−
1.5 LAWS, TECHNICAL PRESCRIPTIONS AND DIRECTIVES
When installing the appliance it is necessary to follow and comply with the following regulations:
−current regulations on the matter;
−any hygienic-sanitary regulations concerning cooking environments;
−municipal and/or territorial building regulations and fire prevention prescriptions;
−current accident prevention guidelines;
−electricity board regulations concerning safety;

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
5GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
−the regulations of the electrical power supply company or agency;
−any other local prescriptions.
1.6 SPECIAL REQUIREMENTS FOR THE INSTALLATION SITE
−The room in which the appliance is to operate must be well ventilated.
−In addition, it is good policy to locate the appliance under an extractor hood so that cooking vapours can
be removed rapidly and continuously.
−To connect directly to the network, it is necessary to provide a device ensuring disconnection to the
network, with a opening gap of contacts that allows complete disconnection in the conditions of
overvoltage category III in accordance with the rules of installation.
−This appliance requires one water connection. The line must be fitted with an on-off valve.
The electrical isolating switch and the water shutoff valves must both be located near
to the appliance, within easy reach for the user.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
6GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
1.7 TECHNICAL DATA
B8FXEN9 - B8MFXEN9
B8FIEN9 - B8MFIEN9
B12FXEN9 - B12MFXEN9
B12FIEN9 - B12MFIEN9
TECHNICAL DATA (DIMEMSIONS)
Equipment dim.A
mm
800
1200
Equipment dim.B
mm
900
900
Equipment dim.H
mm
900
900
Equipment dim.H2
mm
1630
1630
TECHNICAL DATA (FUNCTIONALITY)
Pan dimension A
mm
698
1098
Pan dimension B
mm
564
564
Pan dimension H
mm
200
200
Pan area
dm²
39
62
Overvall volume
lt
81
127
Useful volume
lt
60
100
Temperature
°C
45÷295
TECHNICAL DATA (INSTALLATION)
Electric power
kW
10
15
Voltage/Input (standard)**
V
380-415 V 3N 50/60Hz
Rated current ***
A
15,2
22,6
Cable connection ***
mm²
5 x 2,5
5 x 4
IPX
IPX
4
Water pressure
kPa
50÷300
Hot water inlet
Ø"
1/2"
Latent heat emission
W/kW
450
Direct heat emission
W/kW
400
Moisture emission
g/h /kW
588
Sound level
dbA
< 70
TECHNICAL DATA (STORAGE/MOVEMENT)
Packaging dim.A
mm
1070
1300
Packaging dim.B
mm
870
1050
Packaging dim.H
mm
1270
1220
Volume
m³
1,215
1,68
Net weight
kg
148
213
Gross weight
kg
173
251
**Verify on data plate - ***Current and cable for standard tension

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
7GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
1.8 ELECTRICAL SPECIFICATIONS (NON STANDARD
VOLTAGES)
B8FXEN9 - B8MFXEN9 - B8FIEN9 - B8MFIEN9
Voltage
Electric power
Current
Power cable
V
kW
A
nr. x mm²
380-415 V 3 ~
10
15,1
4 x 2,5
220-240 V 3 ~
10
26,2
4 x 6
208 V 3 ~
8,2
22,7
4 x 4
440 V 3 ~
10
13,2
4 x 2,5
460-480 V 3 ~
10
12,1
4 x 2,5
B12FXEN9 - B12MFXEN9 - B12FIEN9 - B12MFIEN9
Voltage
Electric power
Current
Power cable
V
kW
A
nr. x mm²
380-415 V 3 ~
15
22,6
4 x 4
220-240 V 3 ~
15
39,3
4 x 10
208 V 3 ~
12,3
34,1
4 x 10
440 V 3 ~
15
19,7
4 x 4
460-480 V 3 ~
15
18,0
4 x 4

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
8GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
2 POSITIONING, INSTALLATION AND MAINTENANCE
2.1 POSITIONING
−Remove all the packaging and check that the appliance is in perfect conditions. In case of visible damage,
do not connect the appliance and notify the sales point immediately.
−Remove the PVC protection from the panels.
−Dispose of packaging according to regulations. Generally material is divided according to composition and
should be delivered to the waste disposal service.
−There are no special instructions regarding distances from other appliances or walls, however it is
advisable to maintain a sufficient distance to allow any servicing operations to be performed. In the event
the appliance should be installed in direct contact with inflammable walls, it is advisable to fit suitable heat
insulation.
−The appliance must stand level. Small differences in level can be eliminated by screwing or unscrewing
the adjustable feet: A significantly uneven or sloping stance can affect the operation of the appliance
adversely.
−The device can be put in place or as a single unit or in series with other equipment.
2.2 INSTALLATION
Only qualified technicians must perform the installation, maintenance and test of the
appliance.
Before connecting any parts of the appliance to supplies, make sure that the latter is
equivalent the requirements stated in the technical data plate, if the appliance has
been designed for these supplies.
2.2.1 ELECTRICAL CONNECTIONS AND EQUIPOTENTIAL BONDING
Warning! : The appliance is supplied to operate according to the power supply indicated on the
data plate.
−As mentioned, the appliance must be connected to the power supply by way of a multiple pole main
isolating switch and protection device that must be proportioned to the power of the appliance (1 mA per
kW of rated power).
−The earthing system must be efficient.
−As this appliance is type Y equipment (delivery without power cable and plug), the cable and other
hardware needed to make the connection to the electrical power supply must be provided by the installer.
−The power cable shall be of the kind described in the paragraph “Technical data" and shall be resistant to
oil (type H05RN-F o H07RN-F).
−The power terminal board can be reached by removing the lower front panel (unloose the screws). The
cable fastener is on the lower right-hand side.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
9GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
−The cable must be fed in from beneath the clamp. The individual wires are then fastened to the
corresponding terminals of the terminal board. The earth wire must be longer than the other wires, so that
in the event of the cable being jerked or the clamp broken, the live wires will disconnect first. Lock the cord
fastener.
−The appliance must incorporate an equipotential system.
−Connect the terminal on the lower right-hand side marked with the international symbol a connector
with a nominal cross section <10 mm2. All the appliances installed and the earth system of the building
shall be connected like this.
It’s strictly forbidden using the pending electric cable connected with terminal board,
overhanging from the frame, to connect definitely the machine.
ATTENTION!
Cut the tension before to make the connection and/or maintenance .
2.2.2 CONNECTION TO WATERWORKS
−Water inlet pressure must be between 50 and 300 kPa, otherwise install a pressure regulator on the line
before the appliance.
−Install a cut-off valve for each supply on the line before the appliance.
−Water connections are fitted in the lower part on the left-hand side of the appliance.
−Make connections according to regulations currently in force.
2.3 COMMISSIONING AND TESTING
−Once all the connections have been made, the appliance and the overall installation must be checked
following the directions given in this manual.
−Check in particular:
−that the protective film has been removed from the external surfaces;
−that the lower front panel removed for the electrical connection of the appliance has been fitted back into
position;
−that connections have been made in accordance with the requirements and directions indicated in this
manual;
−that all safety requirements in current standards, statutory regulations and directives have been met;
−that the water connections are leak-free;
−that the electrical connection has been performed according to standards.
−In addition, check that once the appliance has been installed, the power cord is neither subject to stretch
nor in contact with nor surfaces.
−Now proceed to light the appliance as directed in the instructions for use.
−While the appliance is in use, voltage should not differ from the nominal voltage more than +/- 10%.
−The test report must be completed in full and submitted to the customer who should then sign in
acceptance. With effect from this moment, the appliance is covered by the manufacturer’s warranty.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
10 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
2.4 MAINTENANCE OF THE APPLIANCE
All maintenance operations shall only be performed by a technically qualified service
centre!
−To ensure correct and safe operation, the appliance must be inspected and serviced at least once a year
only. Maintenance includes also controlling the components and tear of pipes, feeding pipes, electrical
components etc.
−It is advisable to replace worn components during maintenance operations to avoid the need for other
maintenance calls and unexpected failures.
−It is also advisable to apply for a maintenance contract with the customer.
2.4.1 PERIODIC MAINTENANCE
Periodic inspection will minimize machine downtime and increase operating efficiency.
FOR THE OPERATOR / FOR THE TECHNICAL SERVICE
GREASING SCREW WITHOUT END
−Turn the tank completely
−Connect a grease fitting to the connection on the lower front on the right side.
−Use the grease nipple 3/4 times.
−Move the tank to an intermediate position
−Use the grease nipple 2/3 times.
−Move the tank (cycle completely overturned and in a horizontal position) 2/3 times.
It is advisable to carry out this operation every three months, or whenever the overturn is tiring or noisy.
FOR THE TECHNICAL SERVICE
At each intervention:
−Close all the panels carefully.
−Keep the inside of the sides, where the components are present, clean and dry.
−Keep wiring and electrical connections in good condition.
CHECKS / ANNUAL INTERVENTIONS
1) Greaseing of the tilting rod bearing.
−Remove the front panel of the machine.
−Connect a grease fitting to the bearing located behind the wall from which the tilt rod comes out.
−Use the grease nipple 2/3 times.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
11 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
2) Check the panels coupling, they must be perfectly closed with all screws.
3) Check water supply seal (water filling tap).
4) Verification closing terminals of electrical parts connections. Cleaning of electrical parts.
2.4.2 POSSIBLE FAILURES AND THEIR ELIMINATION
Only a qualified technical assistance service can intervene as specified below!
Before resetting the safety thermostat always remove the cause that caused your
intervention!
EVENT AND POSSIBLE DEFECT
−The contents of the tank do not heat up:
−Intervention of the safety thermostat;
−Working thermostat failure
−Switch/selector failure
−Failure to resistances;
−
−Low efficiency of the tank:
−Check the heating elements.
−
−The Bratt Pan continues to operate with the thermostat disconnected:
−The contacts of the remote control switch are Blocked.
−
ACCESSIBILITY TO COMPONENTS AND INTERVENTION
Remove the power to the appliance (remove the Fuses)
To facilitate the accessibility to the parts to be replaced it is necessary to remove the front panel, after having
removed the temperature control knob, the handle of the water load tap and the control handwheel for the
tilting of the tank of Cooking.
Replacing the working thermostat or the safety thermostat − Remove the Bratt tub Dashboard.
−Remove the cover of the Electrical components box on the front panel.
−Mechanically and electrically disconnect the faulty thermostat.
−Assemble the new thermostat by passing the bulbs through the holes in the components box.
−House the thermostat bulb on the bottom of the tank using the fixing bracket.
−Warning Assemble the bulbs in the bath bottom in the same way as the thermostat bulb to be
replaced!! When replacing the thermostats, pay attention to the capillary of the thermostat itself
(avoid too narrow curves rmin = 20 mm!!) and avoid crushing under the fixing bracket to the
bottom of the tub. Possibility of starting or breaking the Thermostat.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
12 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
Place the two bulbs of the thermostats in the special quarries (1), make sure that they are completely threaded
to the end, curve the capillaries, respecting minimum R 20mm. Lock the bulbs with the retaining bracket (2).
Caution: do not crush the capillary in the closed phase of the bracket (2).
Check that the bulbs do not move from the starting Position.
Switch replacement
−Remove the cover of the Electrical components box on the front panel.
−Disassemble the electrical components box from the front panel
−Replace the switch by unscrewing the locking screws, having also removed the coaxial working
thermostat.
−Mount the new switch in the reverse sequence.
Changing the remote control switches
−Remove the cover of the Electrical components protection box.
−Assemble the new contactor.
−
Replacing resistances (the following steps indicate the angle αto which the tub should be rotated to perform
the work).
−(α = 30 °)
−Remove the part. A unscrewing the screws (1). (DIS. 1)
−Remove the heat shrinkingsheath (4). It is advisable to heat it to facilitate disassembly. (DIS. 3)
−Disconnect the power supply cables from the resistance (s). (DIS. 3)
−(α = 80 °-max.)
−Loosen the fastening screws (3) from Pos. 3.1 to Pos. 3.2. (DIS. 1)
−Turn the part. C. (DIS. 2)
−Loosen the fastening screws (2) from pos. 2.1 and tighten them in pos. 2.2. You need to move the part. B
to the rear Area. (DIS. 1)
−Remove the Parts. D and E from the faulty resistance. (DIS. 2)
−Remove the resistance to be replaced towards the rear, rotating the terminals of the Resistor. (DIS. 4)
−Position the new resistance (with reversed sequence to the replaced one).
−Take care to position the resistance against the part. E and check that the terminals of the new Resistance
are aligned with the other Resistances. (screw Tightening torque 8 Nm). (DIS. 2)

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
13 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
−Return the part. B towards the front zone, bringing the screws 2 back to pos. 2.1. and close Them. (DIS. 1)
−Close the part. C and return the screw (3) to Pos. 3.1. (DIS. 1)
−(α = 30 °)
−Insert the heat shrinkingsheath into the connection Cables. (DIS. 5)
−Connect the terminals of the new resistor (screw tightening torque 1.5 Nm). (DIS. 5)
−Attention during the connection phase of the resistance, place a feedback (finger) in the resistance
terminal, to avoid damaging it when closing the SCREW.
−Heat the heat shrink sheath (190 °C) and adhere to the resistance shank and the Cable. Use a nose pliers
to crush the thermo-shrinking itself, making it adherent to the Wire.
−Reposition the part. A paying attention that it is inside the front profile of the tank and fasten it with the
screws (1) (DIS.1-A. 1)

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
14 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
15 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
3 USE
3.1 WARNINGS AND HINTS FOR USER
−This manual contains all the instructions required for a proper and safe use of our appliances.
−Keep the manual in a safe place for future consultation!
−This appliance is for catering use, hence they must be used only by trained kitchen staff.
−The appliance must always be kept under control during use.
−Warning! : The manufacturer shall not be held responsible for injuries or damage due to the non-
compliance with safety rules or an improper use of the appliance by the operator.
−Some improper operating conditions may even be caused by an improper use of the appliance, therefore it
is important to train personnel properly.
−All the installation and maintenance operations must be performed by fitters who are members of
an official register.
−Respect the periods required for maintenance. With this is mind, customers are recommended to sign a
service agreement.
−In case of failures concerning the appliance, all outputs (electrical power supply and water) must be cut off
instantly.
−In case of recurrent failures, contact a service technician.
3.2 INSTRUCTIONS FOR USE
−Before cooking with the appliance for the first time, wash the interior of the cooking vat thoroughly.
WARNING! :
Fill the cooking vat up to a maximum of 40 mm under the overflow border, according to
the maximum level mark, including the food to be cooked.
WARNING! :
Loading water in the vessel through the faucet, make sure there is not hot oil in the
vessel.
WARNING! :
When opening the cover, wear personal protective equipment (gloves type
athermal).
Danger of burns!

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
16 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
3.2.1 SWITCHING ON, START COOKING
−Connect the appliance by turning on the main switch installed before it.
−Starting from position “0” turn the thermostat knob to desired temperature between 45° and 295°C: the
signal lamps will light , the green one indicates that the appliance is on and the orange one indicates that
heating elements are on; when the desired temperature is reached this signal lamp will go out.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
17 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
3.3 EMPTYING THE COOKING PAN:
−The device serves to facilitate the emptying of the tank. This device is operated by handwheel placed on
the right side in the front. By turning the hand wheel clockwise the tank rises, by turning the tank counter-
clockwise lowers.
−Motorized versions the tilting of the pan is achieved by the selector (see FIG. CONTROLS - MOTOR
TILTING PAN .By turning the selector to the left pan gets up, turning it to the right pan is lowered .
ATTENTION:
The phases of rotation ( lifting and back) of the cooking vessel , must be carried out
and monitored by a single operator : it avoids the possibility of accidental injury to
other people.
ATTENTION:
During the emptying of the tank , the operator must stand on the right side of the
machine paying attention to the leakage of the contents from the hot pan and any
sketches.
Must enforce Furthermore , the staff present in the room , a safe distance from the
perimeter of the machine of at least 2 m in both emptying phase that return of the pan.
As soon as the tank rises from the cooking position (horizontal), the heating switches
off automatically.
Returning the tank to cooking position (horizontal) the heating system automatically
turns on.
ATTENTION:
To avoid re-ignition of the heating when the tank returns to cooking position
(horizontal) with empty tank (possible overheating):
Turn the thermostat to position "0", before tilting the tank.
3.3.1 OPTIONAL BY-PASS MANUAL TILTING OF THE COOKING TANK
−In the event of a power failure, or due to a motor fault, the overturning can be performed manually by
inserting the supplied lever in the special peephole (see details and details- optional BAM0010). By
turning the handwheel clockwise the bowl rises, turning it counterclockwise the bowl is lowered.
ATTENTION:
Once performed the movement of the vessel, remove the lever for manual tipping.
RISK OF INJURY !!!

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
18 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
4 CLEANING AND CARE
4.1 CLEANING AND CARE OF THE APPLIANCE
−Do not use aggressive substances or abrasive detergents when cleaning the stainless steel components.
−Avoid using metal pads of the steel parts as they may cause rust. For the same reason, avoid contact with
materials containing iron.
−Do not use sandpaper or abrasive paper for cleaning; in special cases use a powder pumice stone.
−In case of particularly resistant dirt, it is advisable to use abrasive sponges (e.g. Scotch-Brite).
−It is advisable to clean the appliance only once it has cooled down.
4.1.1 DAILY CLEANING
The appliance must be disconnected from the power supply during cleaning.
When cleaning the appliance never use direct jets of water to prevent infiltration of
the liquid and damage to components.
−Clean the cooking vat with water and a detergent, rinse thoroughly and dry well with a soft cloth.
−External surfaces should be washed down using a sponge, and hot water with a suitable proprietary
cleaner addend.
−Rinse always thoroughly and dry with a soft cloth.
4.2 SPECIAL PROCEDURES IN CASE OF PROLONGED
INACTIVITY
−If the appliance is to stand idle for any length of time (e.g. holidays or seasonal closing), it must be
cleaned thoroughly, leaving not traces of food or dirt.
−Leave the lid open so that air can circulate inside the vat.
−For added care after cleaning, the external surfaces can be protected by applying a proprietary metal
polish.
−Be absolutely sure to shut off all utilities (electrical power supply and water).
−Air the room appropriately.
4.3 SPECIAL PROCEDURES IN CASE OF FAILURES
−If the appliance should not work properly during use, turn it off immediately and close or cut off all supplies
(electrical power supply and water).
−Apply to a service centre for help.

INSTRUCTION MANUAL FOR INSTALLATION, MAINTENANCE AND USE Rev-01BR.E080-
200-00-DU-GB-01
19 GB
RECTANGULAR BRATT PANS ELECTRIC TYPE “BR8E080I - BR8E080I.M” “BR9E090I –
BR9E090I.M” “BR1E120I – BR1E120I.M” “BR1E150I – BR1E150I.M” “BR1E160I –
BR1E160I.M” “BR1E200I – BR1E200I.M”
The manufacturer shall not be held responsible nor has any warranty commitments
for damage caused by non-compliance with prescriptions or by installation not in
conformity with instructions.
The same applies in case of improper use or different application by the operator.
4.4 HOW TO PROCEED, IF …
WARNING! :
Problems and failures may occur even when the appliance is used properly. Here is a list of the mist
probably situations and controls that the operator should perform to avoid applying to a service centre
unnecessarily.
If the problem is not solved after the necessary controls, turn off the appliance immediately, unplug it,
cut off any supplies and apply to a service centre.
−… the vat contents do not heat
up:
−check that the power ON/OFF switch installed before the appliance
is on;
−otherwise turn off the appliance and apply to a service centre, as
the safety thermostat may have been activated due to an excess of
temperature in the cooking vat.
−… the bratt pan continues to
operate with the thermostat
switched off
−
−switch the appliance off with the on/off switch located upstream of
the appliance and contact the technical assistance service.