TEFAL EASY STORE User manual

2- LOCKING SYSTEM FOR RETAINING
THE IRON ON THE BASE
Your steam generator is fitted with a system for retaining the iron on its
base.
• Locking hoop for retaining iron for ease of carriage.
• Hoop release button to free the iron for use.
1.To carry your steam generator by the iron handle:
- place the iron on the iron rest of the generator and raise the retaining hoop
over the iron until it locks into place (audible click) (1).
- grasp the handle of the iron to carry your steam generator (2).
2. Place your steam generator on a stable, horizontal heat-resistant surface.
3.
Grasp the handles of the removable tank and pull horizontally to remove it (3).
4. Fill up the water tank taking care not to exceed the maximum level just
below the filler cover (4).
5. Replace it firmly in its housing, making sure it is fully into place (5).
3- PREPARING YOUR STEAM GENERATOR
English
031837 - 50/04
Steam control
button
Turbo steam button
(depending on
the model)
Temperature control
slide for the iron Removable
water
tank filler
cover
Iron rest
Iron retaining hoop
Boiler rinse plug and steam
cord fastener clip
Iron-base
steam cord
Power cord storage space
Steam output
control dial
Orange “boiler
rinse” light
Red “removable water
tank empty” light
Thermostat
light
Steam generator boiler
(in the base unit)
Handles for removing
and replacing
the water tank
CONTROL PANEL
Power cord reel button
(depending on the model)
Illuminated
on / off switch
10- MAINTAINING YOUR STEAM GENERATOR
• Before cleaning, ensure that your steam generator is unplugged
and that the soleplate and the iron rest have cooled down.
• Do not use detergent or descaling products for cleaning the soleplate
or the base-unit.
• Never hold the iron or the base unit under the tap.
• Do not place the iron on a metal rest as this could
damage it.
Place it on the iron-rest on the base unit :
it has non-slip pads and has been designed to
withstand high temperatures.
1. Empty and rinse the removable water tank (15).
2. Regularly clean the soleplate with a damp,
non-metallic washing up pad.
3. Clean the plastic parts of the appliance occasionally with a soft cloth.
9- TURBO STEAM FUNCTION
(depending on the model)
Press 2 or 3 times on the turbo steam button to obtain
a more powerful burst of steam (14) :
• for ironing thicker fabrics,
• to eliminate creases,
• for powerful vertical steaming.
Be careful :
Use the turbo steam function very carefully
because of the exceptional power of steam that may cause burns.
NOTE :
Continuous use of the turbo steam function will begin to cool the iron
and may cause water to drip from the iron. If this occcurs, stop using
the turbo steam function and allow the iron thermostat to reach tem-
perature again (thermostat light will come on and go off) before using
this function again.
7- WHEN THE RED LIGHT
“WATER TANK EMPTY” COMES ON
There is no more steam.The removable water tank is empty (12).
1. Grasp the handles of the removable tank and pull horizontally to remove
it ; fill with water.
2. Replace and push it firmly into place
3. Press the “restart” button on the control panel to continue ironing.
8- VERTICAL STEAM IRONING
1. Set the iron temperature control slide and the steam output
control dial (located on the control panel) to the MAX position.
2. Hang the garment on a coat hanger and hold the fabric slightly
taut with one hand.
As steam is very hot, never attempt to remove creases from
a garment while it is being worn, always hang garment on a
coat hanger.
3. Holding the iron in a vertical position, tilted slightly forwards,
press repeatedly on the steam control button (under the iron
handle) moving the iron from top to bottom (13).
Recommendations :
For fabrics other than linen or cotton, hold the iron a few centimetres
from the garment to avoid burning the fabric.
6- USING YOUR STEAM GENERATOR
1. Place the iron's temperature control slide according to the type of fabric to be
ironed (9).
2. The thermostat light comes on.
Be careful ! The steam generator is ready when the thermostat light goes
out and when the green “steam ready” light stays on.
Note: it is normal for the steam cord to become warm during use.
3. Adjust the steam output control dial located on the control panel (10).
To obtain steam, press on the steam control button beneath
the iron handle and keep it pressed (11).The steam will stop
when you release the button.
It is recommended that you start with fabrics to be
ironed at a low temperature: synthetics (
● ).
For delicate fabrics (
● ), press the steam control button
(under the handle of the iron) intermittently to avoid
possible water droplets appearing with the steam.
Set the temperature control slide and steam output control dial according
to the type of fabric to be ironed :
Type of fabric
Linen
Cotton
•••
Wool
Silk, Viscose
••
Synthetic,
Polyester,Acetate,
Acrylic, Polyamide
•
Setting the temperature
control slide
Setting the steam output
control dial
(9) (10)
(11)
5- OPERATING THE CONTROL PANEL
• Flashing green light : the water is hea-
ting up in the boiler.
• Continuous green light : steam is ready
for use.
• Continuous red light :
the water tank is empty.
• Orange “boiler rinse” light
flashes : your boiler needs rinsing.
Note: the appliance must be cold
(see section 11).
“Restart” button:
• to be pressed briefly after each refill of the water tank to start ironing again
(see paragraph 7),
• to be held pressed for 2 or 3 seconds after rinsing the boiler (see paragraph 11).
linen
cotton
lin
coton
laine
soie
synth.
wool
silk
synthetic
4- USING YOUR STEAM GENERATOR
1. Press the release button to lower the iron retaining hoop (6).
2. Completely unwind the power cord from its storage space before connecting
to an earthed socket (7).
3. Press on the on / off switch (located on the side of the base unit) (a): the green
light (located on the control panel) flashes and the boiler heats up (b).It will take
around 2 minutes for steam to be produced which is indicated when the green
“steam ready” light stops flashing (8).
• The first time the appliance is used, there may be some fumes and smell but
this is not harmful. They will not affect use and will disappear rapidly.
• When starting, and regularly while it is being used, your steam generator's elec-
tric pump injects water into the boiler. It makes a noise but this is quite normal.
You may also hear a clicking noise which is the steam valve opening.Again this is
normal. If you are pressing on the steam control button at this time you may lose
a little steam pressure momentarily.
1- UNDERSTANDING YOUR
STEAM GENERATOR
• To prime the steam circuit, either before using the iron for the first
time, or if you have not used the steam function for a few minutes,
press the steam control button several times in a row, holding the
iron away from your clothes.
This will enable any cold water to be removed from the steam circuit
Iron temperature control slide setting:
• Start with the fabrics to be ironed at a low temperature (●) and
finish with those which need higher temperatures (●●● or Max).
- Mixed fibre fabrics: set the ironing temperature to the setting for
the most delicate fabric.
- Woollen garments: press repeatedly on the steam control button to
obtain short bursts of steam, without placing the iron on the garment
itself.This will avoid making the fabric shiny.
Steam output control dial setting:
- Thick fabric : increase the steam setting.
- At a low temperature : set the steam output control dial to the low
position.
To iron without using steam:
• Do not press on the steam control button under the iron handle.
Ironing Board:
For best results, a mesh type ironing board should be used to allow
any excess steam to escape.
• If you are using starch, it should be sprayed onto the reverse side of
the fabric to be ironed.
Recommendations :
PRO EXPRESS &
PRO EXPRESS TURBO
Retaining hoop
release button
CLICK
Retaining hoop release
button
The water to use in your steam generator :
Your steam generator has been designed to operate using untreated tap
water. However, if your water is very hard, mix it 50% untreated tap water
with 50% distilled water.
Types of water to be avoided :
Do not add anything to the contents of the removable water tank, and do
not use water from clothes dryers, scented water, water from refrigerators,
water from air conditioners or rain water. Also do not use filtered, boiled or
bottled mineral water.These contain organic waste or mineral elements that
become concentrated when heated and cause spitting, brown staining or
premature wear to your iron.
(5)
(1) (3)(2)
(4)
CLICK
(6) (7) (8)
(a)
(b)
linen
cotton
lin
coton
laine
soie
synth.
wool
silk
synthetic
linen
cotton
lin
coton
laine
soie
synth.
wool
silk
synthetic
linen
cotton
lin
coton
laine
soie
synth.
wool
silk
synthetic
(12)
(14)
(13)
(15)

11.THE ORANGE “BOILER RINSE” LIGHT FLASHES
Note:
• To extend the efficient operating life of your boiler and
avoid scale particles on your linen, your generator is
equipped with an orange “boiler rinse” warning light that flashes
on the control panel after about 10 uses.
• If your water is hard, increase the frequency.
• Do not use descaling agents for rinsing out the boiler, as they could damage it.
1. TO RINSE THE BOILER USING THE RINSING ACCESSORY
For greater effectiveness and for ease of operation, you are advised to use
the rinsing accessory provided in the box.
It will make it easier to rinse the boiler as the generator will need less handling.
Your rinsing accessory has been designed to work on a wide range of taps.
It is supplied with 2 types of membrane (a) (b). Choose the one best suited
to your tap.
If you do not wish to, or cannot use the rinsing accessory, refer to the advice
in paragraph II (next page).
Before attempting to rinse the boiler of your generator, it is essential
to leave it to cool for at least 2 hours in order to avoid any risk of scalding.
If the orange “boiler rinse” light flashes, you can continue ironing normally
but remember to rinse the boiler first, the next time that you use it.
1. Check that the generator is cold and unplugged.
2. Place your steam generator on the edge of your sink, with the iron to
one side, standing on its heel.
3. Unscrew the cord clip by turning a quarter turn to the left (16).
4. Using a coin, gently unscrew the boiler rinse plug (17).
5. Place the plastic nozzle of the rinsing pipe into the hole of the boiler
and turn gently to the right until it locks. The outlet of this nozzle must be
positioned over the sink (18).
6. Connect the rubber end of the rinsing pipe to a cold tap (19).
7. Turn the tap on gently and gradually and let cold water run through
the rinsing pipe into the sink for about 1 minute (20).
8. Switch off the tap and remove the rinsing pipe.
9. Screw back and tighten up the boiler rinse plug with a coin.
10. Put the cord clip back in place.
11. The next time you use the generator, hold down
the “restart” button for 2 to 3 seconds to turn off
the orange light.
II. TO RINSE THE BOILER WITHOUT THE RINSING
ACCESSORY
Before attempting to rinse the boiler of your generator, it is essential
to leave it to cool for at least 2 hours in order to avoid any risk of scalding.
If the orange “boiler rinse” light flashes, you can continue ironing normally
but remember to rinse the boiler first, the next time that you use it.
1. Check that the generator is cold and unplugged.
2. Place your steam generator on the edge of your sink, with the iron to
one side, standing on its heel.
3. Unscrew the cord clip by turning a quarter turn to the left.
4. Using a coin, gently unscrew the boiler rinse plug.
5. Holding your steam generator in a tilted position, and using a jug,
fill the boiler (in the base unit) with 1/4 litre of tap water.
6. Shake the base unit for a few moments and then empty it completely
over your sink.
To obtain the best result, we recommend that this operation is
done twice.
7. Screw back and tighten up the boiler rinse plug with a coin.
8. Put the cord clip back in place.
9. The next time you use the generator, hold down
the “restart” button for 2 to 3 seconds to turn off
the orange light.
12- PUTTING YOUR STEAM GENERATOR AWAY
1. Place the iron on the rest.
2.Turn off at the main O/I switch and unplug.
3. Raise the retaining hoop over the iron until it locks into place (audible click)
(21).Your iron is then safely retained on its base.
Warning: do not touch the soleplate while still hot.
4. Retract the electric supply cord (22).
On the model with an automatic reel, press the reel button and guide the cord
with your free hand.
5.Allow the iron (and iron rest) to cool for 30 minutes.
6.You can then put your steam generator away carrying it by the iron handle (23).
1
2
Never dismantle your iron : always take it to an Approved Service Centre
HELPLINE
If you have any product problems or queries with your product,
please telephone our Customer Relations team on :
0845 6021454 (UK) (Calls charged at local rate)
[phone] (Ireland)
Consult our web site: www.tefal.co.uk
14- IS THERE A PROBLEM ?
Problems Possible causes Solutions
• The thermostat light and the on/off switch are
not illuminated.
• Water runs through the holes in the soleplate.
• White streaks come through the holes in the
soleplate.
• You have already rinsed the boiler
and the orange “boiler rinse” light
is flashing.
• Brown streaks come through the holes in the
soleplate and stain the linen.
• The soleplate is dirty or brown and may stain
the linen.
• There is little or no steam.
• You have filled the tank but there is no steam.
• The red “removable water tank empty” light is
on.
• Steam escapes from the rinse plug.
• Steam escapes under the appliance.
• The power cord does not fully retract.
(depending on the model).
• The appliance is not switched on.
• You are using the steam control button before the iron is hot
enough.
• Water has condensed in the pipes because you are using steam
for the first time or you have not used it for some time.
• Over use of the turbo steam function (which has cooled down
the iron).
• Your boiler has a build-up of scale because
it has not been rinsed out regularly.
• You have not pressed for long enough on the “restart” button.
• You are using chemical descaling agents or additives in the
water for ironing.
• Your linen is not rinsed sufficiently or you have ironed a new
garment before washing it.
• You are ironing at too high a temperature.
• You are using starch.
• The removable water tank is empty
(red “water tank empty” light on).
• The steam output control dial is set at minimum.
• The tank is not properly in place.
• You have not pressed the “Restart” button.
• The rinse plug has not been tightened correctly.
• The rinse plug seal is damaged..
• The generator is faulty.
• The power cord has lost tension during retraction.
• Check that your appliance is correctly plugged in and press the
illuminated on/off switch (located on the side of the base-unit).
• Decrease the steam output while ironing at low temperature
(steam output control dial on the control panel).
• Wait for the thermostat light to go out before activating the
steam control button.
• Press the steam control button away from your ironing board
until the iron produces steam.
• Stop using the turbo steam function and allow the thermostat
light to come on and go off again before using this function again.
• Rinse out the boiler after every 10 uses, when the orange indica-
tor light flashes (see chapter 11). If your water is hard, increase the
frequency.
• Hold the “Restart” button down for 2 to 3 seconds fo turn off
the indicator light.
• Never add this type of product in the removable water tank or
in the boiler (see our recommendations regarding water to be
used.
• Ensure linen is rinsed thoroughly to remove any soap deposits or
chemicals on new garments which have been sucked up by the
iron.
• See our recommendations regarding temperature control setting.
• Always spray starch on the reverse side of the fabric to be iro-
ned.
• Fill the removable water tank and press the “Restart” button
located on the control panel.
• Increase the steam output (control dial on the control panel).
•
Check that the water tank is pushed firmly into place (see section 3).
• Press the « Restart » button on the control panel.
• Tighten the rinse plug correctly.
• Contact an Approved Service Centre to order a new rinse plug
seal.
• Stop using the generator and contact an Approved Service
Centre.
• Pull the power cord out completely.
Press the button and guide the cord with your free hand.
13- SAFETY RECOMMENDATIONS
• Your steam generator is an electrical appliance. It should be used under
normal conditions. It is intended for domestic use only.
• Your generator is fitted with 2 safety systems :
- A pressure release valve which, in the event of a malfunction, releases any
excess steam.
- A thermal fuse to prevent the appliance from overheating.
• This appliance is not intended to be used by children or without
supervision by persons whose physical, sensory or mental aptitude
to use it in complete safety is impaired. Children must be super-
vised to ensure that they do not play with the appliance.
• The appliance must be used and placed on a stable, heat-resistant
surface.
• Completely unwind the power cord from its storage space before
connecting to an earthed socket.
• Always plug your steam generator into:
- An electrical installation with voltage between 220V and 240V. Connecting
to the wrong voltage may cause irreparable damage to the appliance and
will invalidate your guarantee.
- An earthed socket. If you are using a mains extension lead, ensure that it is
correctly rated (10A) with an earth, and is fully extended.
• Should the power cord or the boiler cord linking the iron to the base unit
become damaged, it must be replaced by a TEFAL approved service centre to
avoid the risk of danger or injury.
Be careful:
• The soleplate and generator iron-rest can become very hot and
cause burns : never touch these parts.
• Your appliance gives off steam which can cause burns.
• Handle your iron carefully, particularly when using the vertical steam
function
• Never direct the steam towards persons or animals.
• Never touch the electric cords with the soleplate of the iron.
• Never leave the appliance unattended :
- when it is connected to the mains,
- until it has cooled down (around 1 hour).
• Do not unplug the appliance by pulling on the cord.
• Always unplug your appliance :
- before rinsing out the boiler,
- before cleaning your generator,
- after each use.
• Before unscrewing the boiler rinse plug, wait until the generator is cold
(unplugged for more than 2 hours).
• Never fill the boiler through the rinse hole (except for rinsing)
• Never immerse your steam generator in water or any other liquid. Never
hold it under the water tap
• While rinsing out the boiler, never fill it directly under the tap.
• The appliance must not be used if it has fallen to the floor, shows evidence
of damage, leaks or fails to function correctly.
Never dismantle your appliance.To avoid any danger, have it inspected in a
TEFAL approved service centre.
• If you lose or damage the boiler rinse plug, have it replaced by a TEFAL
Approved Service Centre.
This appliance is designed for domestic use only. In the case of professional
use, inappropriate use or failure to comply with the instructions,TEFAL
accepts no responsibility and the guarantee does not apply.
ENVIRONMENT PROTECTION FIRST !
Your appliance contains valuable materials which
can be recovered or recycled.
 Leave it at a waste disposal centre.
(a)
1
2
(16) (17) (18)
(19) (20)
(21) (22) (23)
CLICK