teko Astra-8731 User manual

“Astra-8731”
Smart socket
User guide
Manufacturer:
ZAO NTC TEKO
420108, Russia, Kazan
Gafuri, 71 str.
[email protected]z
www.teko.biz
Made in Russia
Rev. 8731-v2_1_instr_en
1 FUNCTION
The smart socket "Astra-8731" (hereinafter
Smart socket) is designed to remotely turn on /
off a device powered by a 100-240 V AC net-
work, connected to smart socket, upon a com-
mand received via a radio from the controller
Security Hub.
2 SPECIFICATION
Operating frequency, MHz ...........................433
Supply voltage, V......................from 100 to 240
Relay specification
Maxloadvoltage, AC,V,................................ 250
Max load current, AC, А,..................................16
Wireless coverage range .............................100
Overall dimensions, mm...................140×80×67
Operating conditions
Temperature range, °С..............from -30 to +55
Relative air humidity, %..........up to 98 at +25°С
without moisture condensation
3 DELIVERY SET
The delivery set includes: user guide –1 copy.
4 INDICATION
Indication
LED
Powering on
Off
Boot time
1-time flash for 1 sec
Power normal
Off
Network
searching
Flashing 5 time/sec
No network
2-time flashings with peri-
od of 25 sec
Registration
command
from laser
tool
Astra-942
Turn on 1 time
for 2 sec
Optimisation
command
from laser
tool
Astra-942
Test command
from laser tool
Turn on 1 time for 10 sec
Note - The indication of notifications (except for
commands from the laser tool) is turned off 60
minutes after the power is turned on. The indi-
cation turns on again for 60 minutes by the
"Test" command from the laser tool (see p. 7).

5 ADDING TO THE SYSTEM
1) Start adding on the mobile or desktop app
Security Hub. Adding starts for 45-60 sec.
2) Power on the Smart Socket, by plugging it
into the selected electrical socket with a voltage
of 220 V, the registration mode of the Smart
Socket starts for 60 sec (the indicator flashes at
a frequency of 5 times / sec).
If after 4 seconds after turning on the power, the
indicator of the Smart Socket displays the indica-
tion "No network", it means that the Smart
Socket was previously added to another radio
network. In this case, it is necessary to reset the
parameters of the previous radio network
(see p. 6), unplug the Smart Socket from the
socket, wait at least 20 sec and repeat the add-
ing procedure (steps 2), 3)).
3) Make sure registration is successful with Se-
curity Hub mobile or web app. If registration is
unsuccessful, repeat the procedure.
6 RESET PROCEDURE
To adding in a new radio network, the Smart
Socket provides reset of the current radio
network parameters:
1) Press and hold the hidden button on the side
surface of the Smart Socket for 5-10 sec,
2) Smart Socket generates a notification "No
network" on the LED and becomes available for
adding in the new network.
7 INSTALLATION PROCEDURE
1) Plug the Smart Socket into an electrical
socket according to the recommendations:
- the position of the Smart
Socket when connected to a
socket - the LED upward, since
in this part of the Smart Sock-
et’s PCB, the antenna is locat-
ed inside the housing. Higher
antenna placement improves
the quality of radio communica-
tions.
- the cable of the device
plugged to the Smart Socket
must not pass through the
Smart Socket’s antenna.
2) Set the operation mode of the relay using
Security Hub mobile or desktop App.
8 WARRANTY
Warranty period of operation - 5 years from the
date of commissioning, but not more than 5
years 6 months from the date of manufacture
and subject to the requirements of the current
user guide.