Tektronix TLA7012 User manual

xx
020-2664-01
TLA6200 & TLA6400 Series Logic Analyzers and
TLA7012 Portable Mainframe
Rackmount Kit
ZZZ
Instructions
*P071175001*
071-1750-01

020-2664-01
TLA6200 & TLA6400 Series Logic Analyzers and
TLA7012 Portable Mainframe
Rackmount Kit
ZZZ
Instructions
xx
Warning
The servicing instructions are for use by qualified personnel
only. To avoid personal injury, do not perform any servicing
unless you are qualified to do so. Refer to all safety summaries
before performing service.
www.tektronix.com
071-1750-01

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tektronix.com to find contacts in your area.

Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
DisconnectPower. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
UseCareWhenServicingWithPowerOn. Dangerousvoltagesorcurrentsmay
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 1

Kit Description
Kit Description
This introduction describes the installation of the rackmount kit for the TLA7012
Portable Mainframe, TLA6200 series logic analyzers, and TLA6400 series logic
analyzers.
CAUTION. This kit requires you to remove the right-side panel of the instrument
rack you intend to use. You must have access to the right side of your instrument
to connect the logic analyzer probes when the instrument is installed in the rack.
The rackmount kit is a collection of parts that, once installed, configure the
instrument for mounting into a standard 19-inch equipment rack.
Products
Product Serial numbers
TLA7012 All serial numbers
TLA6202, TLA6203, TLA6204 All serial numbers
TLA6401, TLA6402, TLA6403, TLA6404 All serial numbers
2 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Kit Description
The following figure shows a completed rackmount installation of a TLA7012
Portable Mainframe with two logic analyzer modules and probes attached.
Installation of TLA6200 series logic analyzers or TLA6400 series logic analyzers
is similar, except as noted in these instructions.
Figure 1: Completed TLA7012 Portable Mainframe rackmount installation
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 3

Kit Description
Kit Parts List
(See Figure 2
on page 5.) Quantity Part number Description
——— 1 ea 020-2664-xx Rackmount kit consisting of the following items:
——— 1 ea 071-1750-01 Instruction manual, available on the TLA Documentation CD or
downloadable from the Tektronix Web site
1 1 ea 436-0426-00 Chassis assembly, CHASSIS ASSY, includes 6-32 and 10-32 screws
2 1 ea 407-5122-00 Bracket, locking
3 2 ea 386-7459-00 Panel, cosmetic
4 1 ea 351-1119-00 Guide, slide (rackmount, left and right)
52 ea 407-5125-00 Bracket, rackmount guide, set of 4 with hardware
6 1 ea 407-5131-00 Bracket, TLA7012 or TLA6200 series rackmount adapter, right side (R)
71 ea 407-5124-00 Bracket, TLA7012 or TLA6200 series rackmount adapter, left side (L)
8 2 ea 367-0530-00 Handle: bow
9 1 ea 407-5671-00 Bracket, TLA6400 series rackmount adapter, left side (L)
10 1 ea 407-5672-00 Bracket, TLA6400 series rackmount adapter, right side (R)
4 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Kit Description
Figure 2: Rackmount kit parts
Warranted Characteristics
When the instrument is installed according to the instructions in this document, the
rackmounted instrument meets all warranted requirements listed in the instrument
specification except for those listed in Environmental Requirements.
Instruments mounted using methods other than those described in these
instructions may not meet their warranted requirements.
See Specifications in the user or service manual that applies to your instrument
model for tables of the warranted characteristics.
Cooling air enters from the bottom-front and right sides. (See Figure 3 on page 6.)
You must provide adequate cool air to meet the ambient temperature requirements.
(See Table 1 on page 6.)
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 5

Kit Description
Figure 3: Instrument cooling
Environmental Requirements
The following environmental characteristics supercede those listed in the user
or service manual for your instrument.
Table 1: Warranted characteristics
Characteristic Description
Temperature, Inside Rack Cabinet
Operating +10 ° C to +45 ° C (+50 ° F to +113 ° F)
Nonoperating -22 ° C to +60 ° C (- 7.6 ° F to +140 ° F)
6 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Kit Description
Clearance Requirements
The rack in which the rack adapted instrument is mounted must provide the
following clearance requirements:
A minimum of 14.0 inches (355.6 mm) of vertical space.
A minimum width of 17.717 inches (450 mm) between the left- and right-front
rails in the rack.
A minimum depth of 20 inches (508 mm).
CAUTION. Adhering to these clearance requirements provides the rack-mounted
instrument with enough clearance for air circulation and accommodation of the
power cord and mounting hardware. Failure to provide these clearances can
result in overheating and can cause instrument faults or failure.
Figure 4: TLA7012 or TLA6200 series instrument with rack adapter installed
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 7

Kit Description
Figure 5: TLA6400 series instrument with rack adapter installed
8 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Installation Instructions
Installation Instructions
This section contains all procedures needed to rackmount the instrument.
CAUTION. This kit requires you to remove the right-side panel of the instrument
rack you intend to use. You must have access to the right side of your instrument
to connect the logic analyzer probes when the instrument is installed in the rack.
Minimum Tool and Equipment List
The following tools are required to attach the rack-adapter kit hardware, install
cabling hardware, and mount the rack-adapted instrument into a standard
equipment cabinet. All tools are standard tools that are readily available.
Table 2: Tools required for rackmount installation
Item no. Name Description
1Screwdriver handle
(magnetic)
Accepts 1/4-inch hexagonal
head driver tips
2No.2Ph
illips or Pozidriv tip Phillips or Pozidriv-driver
tip for number 2 size screw
heads
3T-15Torxtip
Torx-driver tip for T-15 size
screw heads
411/32-inch wrench Wrench or nut driver can be
used to install slides
5Torque driver Accepts 1/4-inch hexagonal
head driver tips
These instructions are for personnel who are familiar with servicing the product.
If you need further details for disassembling or reassembling the product, refer to
the appropriate product manual. Contact your nearest Tektronix Service Center or
Tektronix Factory Service for installation assistance.
WARNING. To prevent the rackmounted instrument from tipping forward onto the
operator, install the instrument so that the operator is able to access all of its
rear-panel connectors without pushing down on the instrument.
Verify that the rack does not become unstable with the instrument fully extended.
Do not leave the instrument extended when finished accessing the rear panel.
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 9

Installation Instructions
Assemble the Shelf
Begin the installation procedure by attaching the brackets to the track assembly:
1. Remove the mounting screw that is attached to each track. (See Figure 6.)
2. Mount one bracket to the front of each track assembly using two 8-32
flat-head screws for each bracket. You must slide the rail within the track
assembly to gain access to the mounting screws and holes. See the latch
detail. (See Figure 7 on page 11.)
Figure 6: Preparing the track assembly
3. Use two 8-32 locking-nut washer assemblies to attach the track on the shelf
assembly, applying 28 inch-lbs of torque. (Move the rail within the track to
gain access to the rearward mounting hole).
Refer to the following figure to help you attach the tracks to the shelf.
10 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Installation Instructions
Figure 7: Rackmount shelf preassembly
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 11

Installation Instructions
Prepare the Instrument Rack
This section describes mounting the rackmount parts to the instrument rack.
1. Remove the right-side panel of the instrument rack.
2. Select two 0.5 inch-spaced holes that have at least 14 inches of clearance
above, on all four rails of the rack. (See Figure 8.)
Figure 8: Vertical clearances for rack installation (left-front rail shown)
12 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Installation Instructions
3. Select the mounting method according to rack type:
To mount the brackets with their rear flanges outside the rear rails, use the
Mounting Method A when doing Step 4. Add a bar nut to the installation
only if the rails have untapped holes.
To mount with the rear flanges inside the rails, use the Mounting Method
B. This mounting method assumes untapped holes.
Figure 9: Installation of slide-out track assemblies in rack (top view)
4. Using the method and hardware determined from step 3, attach the brackets
to the rear rails. The screws should be fully, but lightly, seated so mounting
canbeadjustedlater.
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 13

Installation Instructions
Figure 10: Attaching the rear brackets to the instrument rails
5. Mount the cosmetic trim on the front, using two 10-32 screws each. (See
Figure 11.) (Item 2 in this figure shows you where to locate the shelf during
shelf installation).
Install the Shelf/Track Assembly into the Rack
You will need the following tools to install the shelf/track assembly. (See Table 2
on page 9.)
One screwdriver handle (Item 1)
One number two Pozidriv tip (Item 2)
One torque driver (Item 5)
NOTE. The rack hardware kit contains hardware for mounting the instrument in
several configurations. Not all of the hardware in the kit is needed.
A standard equipment rack has rails with universal hole spacing. If you use a
rack with other than universal hole spacing, you may have to drill additional
mounting holes in the rack.
1.Grab the shelf/track assembly and slide the tracks into the brackets on the rear
rails of the instrument rack.
2.Align the front of the shelf to the bottom of the cosmetic trim on the front of
the instrument rack.
14 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions

Installation Instructions
Figure 11: Installing the shelf/track assembly
3. Install two 10-32, P2 screws through the front brackets to the rack on each
side of the shelf front.
4. Install two 8-32 screws through the shelf tracks to the rear brackets. Attach
the screws with the 8-32 lock nuts included in the kit.
5. Tighten all of the screws and check that the shelf slides in and out easily.
Loosen and adjust, if necessary.
TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions 15

Installation Instructions
Attach the Brackets to the Instrument
1. Set the instrument on its back feet to expose the instrument bottom.
2. Remove the four T-15 Torx screws near the bottom feet. Refer to the
appropriate illustration for your instrument.
Figure 12: Location of screws on the TLA7012 or TLA6200 series instrument for bracket mounting
16 TLA6200, TLA6400, & TLA7012 Rackmount Kit Instructions