Tektronix PHASER 380 User manual

Copyright
©
1997 by Tektronix, Inc. All rights reserved. 063-2818-01
Installing the Printer Station
The Printer Station is designed to safely support the weight of the Phaser
¨
380 color printer, the printerÕs
Lower Paper Tray Assembly, and printer supplies. Adding a Printer Station to the printer raises it to a
comfortable operating height, while providing a convenient location to store supplies and consumable
components, such as ColorStix
¨
ink sticks, paper and transparency media, and a spare maintenance tray.
The Printer Station features hinged doors, a sliding drawer and lockable casters. Mounting recesses in
the top of the cabinet help you to position the printer and the optional Lower Paper Tray Assembly
during installation.
Caution
It is important that you follow these unpacking and setup procedures to avoid risk of
personal injury, and damage to the printer, the Lower Paper Tray Assembly and the
Printer Station.
2818-01
!

2
Installing the Printer Station
Location requirements
Before unpacking the Printer Station, prepare an area that allows appropriate clearances for proper
ventilation of the printer. Install on a level ßoor surface, allowing for no more than 1.3 cm (0.5 in.) tilt
from level across any side of the Printer Station.
Turning off the printer
Before unpacking the Printer Station, prepare the printer to be moved by turning it off using the On/Off
switch located on the rear panel. Allow at least 45 minutes for the printer to cool before moving it.
1.
Use the rear-panel On/Off switch to turn off the printer. This places the printhead in
a safe position for moving the printer a short distance. If you are moving the printer
a long distance, remove the maintenance tray and lock the printhead transit
restraint. Refer to the printerÕs user manual for more information.
Caution
After turning off the printer, wait 45 minutes before moving it to allow the ink in the
printer to solidify. Failure to do so can result in ink spills that can damage the printer.
2.
After the printer powers down, disconnect the power cord and other cables.
3.
If present, disconnect the Lower Paper Tray Assembly cable from the printer.
Unpacking the Printer Station
1.
Using a utility knife, cut open the Printer Station shipping box from the top to the
bottom at each corner.
Warning
The Printer Station weighs 31.4 kg. (69 lbs.). Do not attempt to lift it without the
assistance of another person.
2.
Lift the Printer Station from the Printer Station shipping box.
Printer Station Dimensions Printer Clearances ProductWeights
Height: 51.5 cm (20.25 in.) Top: 45.7 cm (18 in.) Printer Station: 31.4 kg (69 lbs.)
Width: 59.7 cm (23.5 in.) Right Side: 10.2 cm (4 in.) Printer: 100 kg (220 lbs.)
Depth: 62.2 cm (24.5 in.) Rear: 10.2 cm (4 in.) Lower Paper Tray: 36.8 kg (81 lbs.)
Left Side, Front, Bottom:
no restrictions Combined Total: 168.2 kg (370 lbs.)
2818-02
45
Min.
!
!

3
Installing the Printer Station
Placing the printer on the Printer Station
1.
Lock the Printer StationÕs front casters to secure it in place.
2.
Optional: With the assistance of another person, place the Lower Paper Tray
Assembly on top of the Printer Station. The Lower Paper Tray AssemblyÕs feet
should sit inside the recesses on the top of the Printer Station cabinet.
3.
With the assistance of three other people using the printerÕs built-in carrying
handles, place the printer on top of the Printer Station. The printerÕs feet should sit
inside the recesses on the top of the Printer Station cabinet. If you are installing the
printer on top of the Lower Paper Tray Assembly, make sure that the alignment pins
Þt in the holes in the base of the printer.
2818-03
2818-04
2818-05

4
Installing the Printer Station
Organizing printer supplies
The Printer StationÕs sliding drawer provides storage for up to 9 kg (20 lbs.) of printer supplies.
A bottom shelf provides additional storage space for supplies such as paper and transparency media.
Caution
The combined weight of a Printer Station, the printer, a Lower
Paper Tray Assembly and supplies can exceed 178 kg (390 lbs.). To
avoid damage or personal injury, use caution when moving the
Printer Station across uneven surfaces. Before moving the printer,
refer to the printer’s user manual or the instruction label located on
the right side of the printer.
2818-06
R
aser
®
380
ansparency Film
50Sheets
M
ADE
F
OR
E
ACH
O
THER
®
TEKTRONIXPRINTERS&TEKTRONIXSUPPLIES
ForbestresultsuseonlyTektronixbrandsuppliesinyourPhaserprinter.Tektronix assumesno
responsibilityforprinterdamageormalfunctioncausedbytheuseoftonersorothersuppliesnot
manufacturedormarketedbyTektronix.
Storeinacool,
drylocation.
Keepinclosedbox.
R
ColorStix
®
Ink
Phaser
®
380 Printers
Black:016-1540-00
TEKTRONIXPRINTERS&TEKTRONIX SUPPLIES
FOR
PANTONE
CALIBRATED
®
PRINTERS
R
ColorStix
®
Ink
Phaser
®
380 Printers
Black:016-1540-00
TEKTRONIXPRINTERS&TEKTRONIX SUPPLIES
FOR
PANTONE
CALIBRATED
®
PRINTERS
R
ColorStix
®
Ink
Phaser
®
380 Printers
Black:016-1540-00
R
ColorStix
®
Ink
Phaser
®
380
Black:016
R
ColorStix
®
Ink
Phaser
®
380 Printers
Black:016-1540-00
ColorStix
®
Ink
Phaser
®
380 Printers
Black:016-1540-00
ColorStix
®
Ink
Phaser
®
380 Printers
Black:016-1540-00
R
ColorStix
®
Ink
Phaser
®
380 P
Black:016-1540