Teletask AURUS-OLED PLUS User manual

Touch panels
©, TELETASK, GENT, 2020 40 Version June 2020
TDS12032xx AURUS-OLED PLUS touch panel – 4x8 buttons
AURUS-OLED PLUS is a glass touch panel with eight capacitive sense buttons. It features a
hidden menu structure with four customizable pages (two pages are pre-configured as an
audio and a temperature control page).
There are eight (night illuminated) feedback LED’s, a built-in infrared receiver for remote
control, a buzzer and a built-in temperature sensor for room temperature control.
AURUS is available in black, white, gold and aluminium grey versions.
The unit can be mounted in a single wall box or BTicino 506L box as used for the (former)
LATUS- and VFD touch panels. Therefore, the AURUS-OLED PLUS is also the perfect
upgrade/replacement for the LATUS, LATUS-LCD and VFD touch panels.
TELETASK only uses exclusive safety-glass with ceramic printing, hardened at 800°C for all
AURUS family members. Therefore, colour fading is not possible.
APPLICATION
AUTOBUS compatible touch panel
CHARACTERISTICS
General
Solid safety-glass front plate, ceramic background printed and
thermal hardened.
8 capacitive sensitive buttons.
Hidden menu structure (3 extra pages of which 2 pre-
programmed as audio and temperature page – every page is
customizable from out of PROSOFT)
1 hidden “CLEAN” button.
Build-in infrared receiver for remote control (TDS12503).
Build-in temperature sensor for room temperature control (floor
heating, ventilation heating, traditional heating and air-
conditioning).
Buzzer.
Order numbers
TDS12032WH white
TDS12032BL black
TDS12032AU gold
TDS12032LG aluminium-grey
Cleaning
To temporary disable the touch buttons, press long on the
middle dot on the left of the OLED screen.
Use only dry microfiber cloth. Never use liquids or solvents!
SETTINGS
Configuration
Via PROSOFT Suite (V3.5.12 or higher).
AUTOBUS address
Via rotary switches “Tens” & “Unit”.
Jumpers
Terminating resistor (supplied with the interface). To be used
when the interface is at the physical end of the AUTOBUS
cable.
INSTALLATION
Standard mounting
To be mounted with included wall bracket in about any
standard single wall box.
Or order the TELETASK standard single wall box for brick walls
ref. TDS90000AT. For plaster board or other hollow walls order
ref. TDS90000PB.
To be placed in horizontal position.
To remove the AURUS-OLED PLUS after installation, place a
flat-head screw driver in the provided slot at the back of the
housing. A standard flat-head screw driver of 5x100mm
(3/16x4in.) is recommended.
On-wall mounting
Use the TDS90035 on-wall box in case of concrete, marble, …
walls, if the standard in-wall solution is not possible.
Supply voltage
12V (supplied by the AUTOBUS - minimum 9V). Can be
checked in PROSOFT Diagnostics.
CONNECTIONS
AUTOBUS
AUTOBUS connector set supplied with this unit.
POWER CONSUMPTION
Max. 110 mA (all LEDs ON + display ON)
DIMENSIONS
205W x 100H x 13,5D (mm) thickness on wall
NET | GROSS WEIGHT
0,295 kg |0,500 kg
PACKAGING CONTENT
TDS12032xx interface
AUTOBUS connection set + terminating resistor
Wall bracket + adaptor
STORAGE
Temperature
-20°C to +65°C
Relative humidity
15% to 85%
!Avoid high humidity and high temperatures for long time.
IP PROTECTION RATE
IP20
OPERATING RANGE
Temperature
0°C to +50°C max.
Relative humidity
5% to 80% at 25°C (non-condensing ambient)

Touch panels
©, TELETASK, GENT, 2020 41 Version June 2020
SCHEMATIC DRAWING