Teli CS8620i (EIA) User manual

CCD Monochrome
VideoCamera
Operation Manual
Model
CS8620i (EIA) CS8620Ci (CCIR)
CS8630i (EIA) CS8630Ci (CCIR)
CS8620Hi (EIA) CS8620HCi (CCIR)
CS8630H (EIA) CS8630HC (CCIR)
BEFORE USE - GENERAL SAFETY
INSTRUCTIONS
This instruction manual contains important information for the
operator (user) and/or people around him/her to avoid personal
injury, or property damage to him/her or people around him/her by
using this product correctly. Prior to use, read this operation
manual carefully to fully understand its instructions for correct
use.
OWNER’S RECORD
Please fill in the blank below the model name and product serial
number, which is found on bottom chassis of your device. Keep
this number for your record.
Model Name
SerialNo.
WARNINGS & CAUTIONS
[Definition of markings]
The meaning of each mark used in this instruction manual is given
below.
DANGER
This mark warns the user that improper use,
indicated with this mark, may cause death or
severe personal injuries against the user or
people around him/her.
CAUTION
This mark warns the user that improper use,
indicated with this mark, may cause personal
injuries (*1) or material damages (*2) against
the user or people around him/her.
Notes
*1 : Personal injuries mean wounds, burns, electric shocks,
and others for which the person injured need not to be
hospitalized nor to be cared for the long term.
*2 : Material damages mean any direct or consequential
damages related to property or material loss.
This mark indicates what the user SHOULD NOT
DO. The details of things which the user should not
do are described next to this mark.
This mark indicates what the user MUST DO. The
details of things which the user must do are described
next to this mark.
This mark indicates that the user must be alert against
a possible DANGER. The details of the danger which
the user must be aware of are described next to this
mark.
This mark indicates that the user are given a CAUTION
against possible hazards. The details of the caution
which the user must be aware of are described next to
this mark.
●Handling Precautions
DANGER
MUST
If any overheating sign is observed, discontinue
use immediately.
In the event that smoke, smell, or any other
overheating sign is observed, turn its power switch
OFF immediately, and remove its camera cable
from camera connector. Do NOT try to continue to
use your camera. To do so in spite of a clear sign of
a malfunction invites a fire, an electric shock
hazard, or any other serious damage. In such case,
after confirming that there is no risk of a fire
accident, contact us or our dealer/distributor
through which you purchased this device for repair
service. To avoid hazard, do NEVER attempt to
repair it yourself.
MUST
If any malfunctioning sign is observed, discontinue
use immediately.
Do NOT try to use this device when it is
obviously malfunctioning. (Example: No images
on the monitor) In the event of a malfunction, turn
its power switch OFF immediately, and remove its
camera cable from camera connector. In such case,
contact us or our dealer/distributor through which
you purchased this device for repair service.
MUST
If any liquid gets into the device, discontinue use
immediately.
In the event that water, or any other type of
liquid gets into the body, do NOT try to continue
to use the device. To do so invites a fire or an
electric shock hazard. In such case, turn its
power switch OFF immediately, and then
remove its camera cable from camera connector.
After that, contact us or our dealer/distributor
through which you purchased this device for
repair service/technical advice.
MUST
Connection/Disconnection only AFTER
power OFF.
When you connect/disconnect camera connector,
make sure to turn power SW OFF first. This
camera is not designed for “hot-plugging”. Do
NEVER make connection/disconnection while
power ON. Doing so might cause a breakdown.
DANGER
MUST
Use manufacturer-recommended peripheral
devices (option units) only.
Make sure to use option units specified in this
operation manual only. When connected with
any other non-guaranteed peripheral devices,
your camera might fail to perform its full
capacity. In the worst case, it might cause a fire
or breakdown.
NEVER
pull apart
Do NOT disassemble this device.
Do NOT attempt to pull apart, repair, or modify
your camera yourself. To do so might lead to a
fire or an electric shock accident. Contact us or
the dealer/distributor from which you purchased
the device for repair/modification.
DON’T
Do NOT supply any power other than specified.
This device is designed to work only under
specified voltage. Do NOT attempt to supply
the device with power other than specified.
Supplying the device with any unspecified
power invites a fire or an electric shock hazard.
(CS8600 series --- DC+12V)
DON’T
Do NOT use the camera in a high-humidity
environment.
Do NOT place your camera near a humidifier,
or in other high-humidity environment. To do so
might cause a fire or an electric shock accident.
●Handling Precautions
CAUTION
CAUTION
If the camera is operated in the electromagnetic
field, there may be cases where beat noises
(vertical, horizontal, or oblique stripes) appear in
the video output. In that case, take preventive
measures on the electromagnetic-wave
generating source so that your camera do not
receive the interference by the
electromagnetic-wave. Take extra precautions
against electromagnetic-wave-interference if
your camera is used with a servomotor, inverter,
or other electromagnetic-wave-generating
equipment.
CAUTION
Avoid giving a strong shock against the camera
body. It might cause a breakdown or damage. If
your camera is used in a system where its camera
head is subjected to strong repetitive shocks, its
camera head is possible to break down. If you
intend to use your camera in such a situation,
make sure to use an optional camera-connector
-fixing-hardware to connect the connector-plug
to the camera body.
CAUTION
When the camera is not in use, put a lens or a
lens-cap onto the camera head so that the image
pickup plane of CCD is protected from dust,
foreign object, or any other flaw-causing object.
If the glass plane (image pickup plane) gets dirty,
clean it with a cotton swab. When it needs to be
cleaned with a cleaner, be sure NOT to use any
organic solvent other than ethyl alcohol. As a
countermeasure against condensation, when the
camera is moved from a warm
condition/environment to a cold one, take
appropriate precautions to prevent condensation
from forming on the camera.
CAUTION
Do not pull strongly the camera
cable/camera-head nor swing it. The stress from
pulling or swinging may cause damage in the
coating of the cable, or breaks in the inside
wires.
CAUTION
Avoid short-circuiting signal output. Otherwise,
it may cause a malfunction.
CAUTION
Do NEVER expose its camera head to any
intensive light (such as direct sunlight).
Otherwise, its inner image pickup device might
get damaged.
This equipment has been tested and found to comply with the
limits for a class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in
which case the user will be require to correct the interference at
his own expense.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device accept any
interference received, including interference that may cause
undesired operation.
RESTRICTION FOR USE
In the case where a malfunction of this camera (e.g. video output
cut-off) can be expected to lead to a significant accident, avoid
using this device for such system build-in use.
DISCLAIMER (LIMITED WARRANTY)
We assume no responsibility and shall be held harmless for
damage or loss incurred by the user in the following cases.
1.In the case where damage or loss is caused by fire, earthquake,
or other acts of Gods, acts by a third party, misuse by the user
deliberately or erroneously, or use under extreme operating
conditions.
2.In the case where any indirect, additional, consequential
damages (e.g. loss of expected interest, suspension of business
activities) are incurred as results of a malfunction or
non-functioning of this device, we shall be exempted from
assuming responsibility for such damages.
3.In the case where damage or loss is caused by incorrect use
which is not in line with the instructions given in this
operation manual.
4.In the case where damage or loss is caused by a malfunction
resulting from bad connection with other equipment.
5.In the case where damage or loss is caused by repair or
modification done by the user.
PRODUCT DESCRIPTION
Model CS86xxi is a miniature camera series featuring its
ultra-small light-weight body. The CS86xxi camera series is
designed mainly for factory automation, machine vision, and
image measurement application.
FEATURES ⑤DC IN/SYNC
This connector is for DC power input, external sync signal
(1) High resolution input, and video output, to be connected with a power supply,
The 380,000 pixel CCD realizes the horizontal resolution of sync-signal generator, and video monitor.
570TV lines.
High-density images with minimum moire-fringes & beatings (4) DIP SW
are obtained. (CCIR: 440,000 pixels, 560TV lines)
(2) Ultra-compact & light-weight body Using the rear-
p
anel DIP switch, you ca
n
make various mode setting.
Each numbered switch is OFF in LEF
T
position, and ON in RIGHT position.
1
2
3
4
5
6
7
8
9
0
O
N
The camera features its ultra-small light-weight body. Its super-
small body will free you from much of your space restriction
problem. The camera is driven by DC12V.
(3) Electronic shutter
The built-in electronic shutter allows this camera to
capture a fast-moving object clearly and sharply.
(4) AGC (Automatic Gain Control)
This series is equipped with AGC function. With the
[Shutter-speed Setting] X : Don’t care
AGC, the camera obtains optimal images constantly
even when the amount of incoming light fluctuates.
(5) Restart/Reset
When the restart/reset function set ON, the camera
captures images at any timing given by R.R. pulse
input (VD input).
Remark : CS8620Hi, CS8620HCi are possible for a restart/reset
operation only at the field integration mode.
(6) SS (Special shutter) & RTS (Random trigger shutter)
This camera is fitted with special shutter and random trigger
shutter function, which allows the camera to capture images
cued by external trigger input.
(7) Near-infrared region sensitivity
(Model -----H type only)
The CCD integrated in the model CS8620Hi,
CS8620HCi,CS8630H, and CS8630HC has a near-
infrared-region sensitivity. These models capture clear
images even under near-IR shooting condition.
CS8600i Series Spec Lookup Table
Model name
Image
size
TV
format
Near
IR
SS /
RTS R.R.
CS8620i 1/2 type EIA ×○○
CS8620Hi 1/2 type EIA ○○○
CS8630i 1/3 type EIA ×○○
CS8630H 1/3 type EIA ○○○
CS8620Ci 1/2 type CCIR ×○○
CS8620HCi 1/2 type CCIR ○○○
CS8630Ci 1/3 type CCIR ×○○
CS8630HC 1/3 type CCIR ○○○
CONFIGURATION
(1) Camera body 1
････････････････････
････
･･･
(2) Accessory
Operation Manual（English）1
Operation Manual（Japanese）1
CONNECTION / MODE / REAR-PANEL SWITCH
(1) Connector Pin Assignment
Compatible plug: HR10A-10P-12S
(Manufactured by HIROSE ELEC.)
External sync.
Pin
No. HD VD VS/SYNC R.R. Internal sync.
1 GND GND GND GND
2 +12V +12V +12V +12V
3 GND GND GND GND
4 VIDEO
OUT
VIDEO
OUT
VIDEO
OUT VIDEO OUT
5 GND GND GND GND
6 HD IN ----- HD IN HD OUT*
7 VD IN
VS/SYNC
IN R.R. IN VD OUT*
8 GND GND GND GND
9 CLOCK
OUT
CLOCK
OUT
CLOCK
OUT
CLOCK
OUT
10 WEN OUT WEN OUT ----- WEN OUT
11 TRIG IN TRIG IN TRIG IN TRIG IN
12 GND GND GND GND
No. SHUTTER
OFF 1/125 1/250 1/500
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 OFF OFF OFF OFF
6 OFF OFF OFF OFF
7 X X X X
8 X X X X
9 X X X X
0 X X X X
No. 1/1,000 1/2,000 1/4,000 1/10,000
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 ON ON ON ON
6 OFF OFF OFF OFF
7 X X X X
8 X X X X
9 X X X X
0 X X X X
No. Flicker-less 1FLD 2FLD 4FLD
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 OFF OFF OFF OFF
6 ON ON ON ON
7 X X X X
8 X X X X
9 X X X X
0 X X X X
No. 6FLD 8FLD 10FLD
Pulse-width
1 X X X X
2 X X X X
3 OFF ON OFF ON
4 OFF OFF ON ON
5 ON ON ON ON
6 ON ON ON ON
7 X X X X
8 X X X X
9 X X X X
0 X X X X
[Mode Setting]
ＧＡＩＮ TRIGGER Polarity
No. MGC AGC POSI NEGA
1 X X X X
2 X X X X
3 X X X X
4 X X X X
5 X X X X
6 X X X X
7 X X OFF ON
8 X X X X
9 X X X X
0 OFF ON X X
Integration Mode Gamma Correction
No. Frame Field 1.0 0.45
1 X X X X
2 X X X X
3 X X X X
4 X X X X
5 X X X X
6 X X X X
7 X X X X
8 OFF ON X X
9 X X OFF ON
0 X X X X
* HD VD output is available via inner SW selection under internal
sync operation.
(2) Connection Example
TR
IN OUT
VIDEO OUT/
DC IN/SYNC
M GAIN
HD/VD
HIGH 75Ω
HD/VD
SHUT
FR/FL
TRIG
γ
M/AGC
MODE
HD
HIGH-75Ω VIDEO OUTVIDEO IN
SERIAL No.
CLOCK OUT
HD
AC100V IN
TOKYO ELECTRONIC INDUSTRY CO.,LTD.
CAMERA
WEN
TRIGGER
VIDEO OUT
VD
IGGER
To be connected if necessary
VD/VS/SYNC/R.R
(Either one) Camera Cable (option)
Camera Adapter
CA130C
(Rear Panel)
CCD Camera
CS86xxi Series
(Rear Panel)
AC100V
50/60Hz
Clock Output
Video Cable
AC100V50/60Hz
Video Monitor
(Rear Panel)
WEN
* Make sure that video output is properly 75-ohm terminated.
[Restart Reset / Special Shutter]
No. Normal Restart Reset Special Shutter
1 OFF ON ON
2 OFF ON ON
3 OFF ON ON
4 OFF ON ON
5 OFF ON ON
6 OFF ON ON
7 X X X
8 X X X
9 X X X
0 X X X
(3) Rear SW, Potentiometer, Connector
[Random trigger shutter]
No. Normal Mode 1,2 Mode 3,4
1 OFF OFF OFF
2 OFF OFF ON
3 OFF X X
4 OFF X X
5 OFF X X
6 OFF X X
7 X X X
8 X X X
9 X X X
0 X X X
No. Mode 5,6 Mode 7,8
1 OFF ON
2 OFF OFF
3 X X
4 X X
5 X X
6 X X
7 X X
8 X X
9 X X
0 X X
IN OUT
VIDEO OUT/
DC IN/SYNC
M GAIN
HD/VD
HIGH 75Ω
HD/VD
SHUT
FR/FL
TRIG
γ
M/AGC
①
②
③
④
⑤
CS86xxi Series
Rear View
①Gain adjustment potentiometer
This manual gain adjuster is enabled under Manual Gain
Control setting (Gain selection SW: MGC). Turned
clockwise, video amplification gain increases.
②Mode selection SW
This is the camera mode selection switch.
③75-ohm termination ON/OFF SW
This SW switches external-sync input terminal 75-ohm
termination ON/OFF. When set in right side, the
termination is 75-ohm. When set in left, it is 10k-ohm.
The initial factory setting is in OFF position.
④HD VD IN/OUT selection SW
This is the HD VD sync-signal IN/OUT selection switch.
The status is HD VD IN when set in left side, HD VD OUT
when in right. The initial setting is EXT.
D3002864 A

ｔ１ ｔ２
ＶＤ
ＨＤ
Specification
Material Lens-mount, Rear panel : Aluminum die-cast
Cover : Anticorrosio aluminum alloy
Processing Lens-mount, Rear panel : Cation coati g
Cover :Leather sati coating
n
n
n
OPERATION
(1) Connect each system component as illustrated in Section 4
above.
(2) Turn the power switch of the video monitor ON.
(3) Feed power to the camera.
(4) Confirm that images appear on the video monitor. Adjust the
lens aperture so that the optimal illumination is obtained.
(5) While monitoring the images on the video monitor, adjust the
lens-focus so that the sharpest images are obtained.
(6) Adjust sensitivity. The factory setting is in MGC (Manual Gain
Control). AGC (Automatic Gain Control) mode is also available.
The selection is made via DIP SW selection on the rear side.
Under the MGC mode, the rear-panel M GAIN potentiometer is
enabled for manual gain adjustment by an user.
(7) Select gamma factor. The factory setting is 1.0. The selection
between 1.0 and 0.45 is made via the rear DIP SW selection.
(8) Select the electronic shutter ON/OFF. The factory setting is in
OFF position. To set E-shutter ON, use the rear-panel DIP SW.
(9) Select integration mode. The selection between the frame/field
integration is made via the rear DIP SW selection. The initial
factory setting is the frame integration.
(10) Set restart/reset, special shutter, or random trigger shutter
mode as necessary. The factory setting is all in OFF position.
Each function is set ON/OFF via the rear DIP SW selection.
(11) If you need HD VD output, use the rear SW under internal
sync operation.
(12) For connection with an image processor and other
peripheral devices, this camera is provided with CLK OUT
(Clock output function).
SPECIFICATION
(1) TV system (EIA) Based on EIA standard
(CCIR) Based on CCIR standard
(2) Image sensor Interline CCD
･Total pixel counts
(EIA) 811(H)×508(V)
(CCIR) 795(H)×596(V)
･Active pixel counts
(EIA) 768(H)×494(V)
(CCIR) 752(H)×582(V)
･Video output pixel counts
(EIA) 756(H)×485(V)
(CCIR) 742(H)×575(V)
･Cell size
(CS8620i,CS8620Hi) 8.4×9.8μm
(CS8620Ci,CS8620HCi) 8.6×8.3μm
(CS8630i,CS8630H) 6.35×7.4μm
(CS8630Ci,CS8630HC) 6.5×6.25μm
･Scanning area
(CS8620i,CS8620Ci, 6.5×4.85mm
CS8620Hi,CS8620HCi) (type-1/2)
(CS8630i,CS8630Ci, 4.8×3.6mm
CS8630H,CS8630HC) (type-1/3)
･H drive frequency (Internal sync)
(EIA) 14.31818MHz ±100ppm
(CCIR) 14.18750MHz ±100ppm
(3) Scanning lines
(EIA) 525 lines
(CCIR) 625 lines
(4) Scanning format 2 : 1 interlace
(5) Sync System Internal/External
(automatic change over)
(6) Scanning frequencies (internal synchronization
Horizontal drive (H) mode)
(EIA) 15.734kHz ±100ppm
(CCIR) 15.625kHz ±100ppm
Vertical drive (V)
(EIA) 59.94Hz ±100ppm
(CCIR) 50.0Hz ±100ppm
(7) Aspect ratio 4:3
(8) Sensitivity
･Standard (GAIN:MGC,γ=1.0)
(CS8620i,CS8620Ci 200 lx ､F5.6 (3100K)
CS8630i,CS8630Ci)
(CS8620Hi,CS8620HCi) 400 lx ､F11 (3100K)
(CS8630H,CS8630HC) 400 lx ､F8 (3100K)
･Minimum (GAIN:MAX､γ=0.45)
(CS8620i,CS8620Ci) 0.2 lx ､F1.4
(CS8630i,CS8630Ci) 0.2 lx ､F1.4
(CS8620Hi,CS8620HCi) 0.1 lx ､F1.4
(CS8630H,CS8630HC) 0.2 lx ､F1.4
(9) Video output VS:1.0V(p-p) /75Ω
VS(Video+SYNC)
(10) Resolution
Horizontal
(EIA) 570 TV lines
(CCIR) 560 TV lines
Vertical
(EIA) 485 lines (350 TV lines)
(CCIR) 575 lines (410 TV lines)
(11) S/N 60dB(p-p)/rms (typical)
(GAIN:MGC､γ=1.0)
(12) Input signal
①External sync pulses HD･VD/SYNC/VS
･Pulse level HD､VD､SYNC:2～6V(p-p)
VS:1.0(SYNC0.3)V(p-p)
･
Input impedance 75Ω/ High Switch-able by the
panel SW
(Initial factory setting: High)
･Scanning system 2 : 1 interlace
･Polarity Negative
･Pulse width HD:6.4±3μs
VD:150～800μs
･Frequency
Horizontal (fH)
(EIA) fH=15.734kHz ±2%
(CCIR) fH=15.625kHz ±2%
Vertical (fV)
(EIA) fV=2fH/525
(CCIR) fV=2fH/625
･Scanning lines
(EIA) 525 lines
(CCIR) 625 lines
･Phase different The difference in phase
between the falling edge of
VD and that of HD is shown in
the figure below.
1st FIELD for EIA 2nd FIELD for EIA
2nd FIELD for CCIR 1st FIELD for CCIR
t1＝０±５μＳ t2＝（１／２）fH±５μＳ
②Shutter trigger (TRG)
･Pulse level VL=0～0.5V VH=2～5V
･
Input impedance High impedance
･Polarity Positive
･Pulse width 2μs～1/4s
(13) Output signal
①HD/VD pulses Under internal sync operation,
output available by the panel
SW selection
(Initial factory setting: IN)
･Output level HD: 4.5±0.5V(p-p)
(high impedance) VD: 5.0±0.5V(p-p)
･Scanning system 2 : 1 interlace
･Polarity Negative
･Pulse width
(EIA) HD: 6.36±1μs, VD: 572±10μs
(CCIR) HD: 6.41±1μs, VD: 480±10μs
･Frequency
Horizontal (fH)
(EIA) fH=15.734kHz ±100ppm
(CCIR) fH=15.625kHz ±100ppm
Vertical (fV)
(EIA) fV=2fH/525
(CCIR) fV=2fH/625
･Scanning lines
(EIA) 525 lines
(CCIR) 625 lines
②Clock pulse
･Output level 2.0±0.3V(p-p)
(highimpedance)
･Frequency (Under internal synchronization)
(EIA) 14.31818 MHz±100ppm
(CCIR) 14.18750 MHz±100ppm
③WEN Under random trigger shutter
operation, WEN is output
during the period starting from
the VIDEO OUT START VD
falling edge through the VIDEO
OUT END VD falling edge.
･Polarity Positive
･Diagram The circuit is shown in the
figure below.
(14) Sensitivity setting Mode selection via panel SW
(Initial factory setting: MGC)
AGC(Automatic Gain Control)
MGC (Manual Gain Control)
(15) MGC Manual sensitivity adjustment
available
(16) Gamma 1.0 / 0.45 selectable via rear panel
DIP switch
(Initial factory setting: 1.0)
(17) White clip Clip-level: 820±40mV(p-p)
(Excluding SYNC)
(18) Electronic shutter Normal shutter
The following shutter speed setup
is possible by rear panel DIP
switch selection.
Normal,1/125,1/250, 1/500,
1/1000,1/2000, 1/4000, 1/10000s,
and Flicker-less (Initial Factory
setting: Normal)
Slow-speed shutter
1FLD,2FLD, 4FLD, 6FLD,8FLD,
and 10FLD
(19) Random trigger shutter RTS Mode selection available
1Shutter-speed Switch
Setting Internal sync SYNC
Non-reset
2Shutter-speed TRIG
Pulse-width Setting Internal sync SYNC
Non-reset
3Shutter-speed Switch
Setting Internal sync SYNC Reset
4Shutter-speed TRIG
Pulse-width Setting Internal sync SYNC Reset
5Shutter-speed Switch
Setting
HD / VD IN
(*1)
SYNC
Non-reset
6Shutter-speed TRIG
Pulse-width Setting
HD / VD IN
(*1)
SYNC
Non-reset
7Shutter-speed Switch
Setting
HD / VD IN
(*2)
SYNC
Non-reset
8Shutter-speed TRIG
Pulse-width Setting
HD / VD IN
(*2)
SYNC
Non-reset
*1: Consecutive HD / Consecutive VD IN
*2: Consecutive HD / Single VD IN
(20) Special shutter User-defined shutter-timing and
shutter-speed cued and timed by
shutter trigger and restart / reset
pulse input ON / OFF selectable
via rear panel DIP SW
(Initial factory setting: OFF)
(21) CCD integration mode Field / Frame storage(integration)
Switch-able by rear panel DIP
Switch Selection (Initial factory
setting:frame integration)
(22) Restart/Reset Restart / Reset function available
via rear panel DIP-SW selection
(Initial factory setting: OFF)
Remark : CS8620Hi, CS8620HCi are possible for a
restart/reset operation only at the field
integrationmode.
(23) Power source DC12V±10%[Ripple level
: Less than 10mV(p-p)]
(24) Power consumption approx. 1.3W
(25) Ambient condition
･Performance assurance
Temperat ure 0℃～40℃
Humidity 20～80% (No condensing)
･Operation assurance
Temperature -10℃～50℃
Humidity 20～80% (No condensing)
･Storage
Temperature -20℃～60℃
Humidity 20～95% (No condensing)
(26) Lens mount C-mount
(27) Flange back 17.526mm
(28) Dimensions 29(W)×29(H)×31(D)mm
(Excluding protruding part)
(29) Mass Approx. 50g
(30) Option unit
･Power adapter CA130C (AC100V)
･Power / Video connector (Maker : Hirose denki)
HR10A-10P-12S
･Camera cable CPSC2000 (2m)
･Tripod adapter
･IR cut filter
DRAWINGS
Typical spectral response
[The lens characteristics and light source characteristics is not
reflected in the table.]
CS8620i,CS8620Ci
CS8620Hi
CS8630H,CS8630HC
HOW TO FIX CAMERA
(1) Use tripod
If you use tripod, use camera mounting kit (optional) and fix
camera.
(2) Use fixing holes on the bottom of camera
If you use fixing holes on the bottom of camera, Please use
screw (M2 and M3).
Please use screw length less then 3mm.
2-M2 depth 3
CS8630i,CS8630Ci
CS8620HCi
Head Office 7-1, 4 chome, Asahigaoka, Hino-city,
Tokyo 191-0065, japan
・Telephone [phone]
・Facsimile [phone]
Kansai Branch Nitto Building, 1-2, 2chome,
Sakaemachi-dori, Chuo-ku,
Kobe, Hyogo 650, japan
・Telephone [phone]
・Facsimile [phone]
Fukuoka Division Yen Building, 7-21, 3 chome, Hirao,
Chuo-ku, Fukuoka 810, Japan
・Telephone [phone]
・Facsimile [phone]
Dealership
WEN
2SC4176
51
10k
4700
CAUTION
If the screw is long, it touches with printed circuit board,
and it causes some trouble and accident.
3-M3 depth 3
4-M2 depth 3
Lens screw
all-in depth
Cover
Lens mount
Rear panel
D3002864 A