Teli CS400B series User manual


D4119853A
CCD B/W CAMERA
CS4000B/BC SERIES
OPERATIONMANUAL
Before using your CCD camera, please read this user's manual to become familiar with the correct usage
procedures. After reading, keep this manual in a safe place for future reference.
TOKYO ELECTRONIC INDUSTRY CO.,LTD.
This user's manual is manufactured from recycled paper.


D4119853A
Important Safety Precautions
The main unit and the user's manual of the product provide information on important contents that
will help prevent injury to those using the product and others, prevent property damage, and
ensure safe use of the product. Please make yourself familiar with this information before using
your CCD camera.
Make sure you understand the meaning of the indications and graphic symbols shown below
before reading this manual. Be sure to observe the precautions indicated.


●
●●
●Description of indications
Indication Meaning of indication
DANGER
Incorrect use or disregarding precautions may result in death or
serious injury
WARNING
Incorrect use or disregarding precautions may result in death or
serious injury
CAUTION
Incorrect use or disregarding precautions may result in personal
injury (*1) or damage to property (*2).
*1: Personal injury refers to injuries, burns, or electric shockthat does
not require hospitalization or repeated hospital isits.
*2: Property damage refers to damage to assets or materials.


●
●●
●Description of graphic symbols
Graphic symbol Meaning of graphic symbol
Prohibited – actions to be avoided at all times. The prohibited actions are
indicated within or near the graphic symbol with illustrations or text.
Required – actions or that must be taken. The required actions are indicated
within or near a graphic symbol with illustrations or text.
Hazardous. The nature of the hazard is indicated within or near the graphic
symbol with illustrations or text.
Caution. The reason for the precaution indicated within or near the graphic
symbol with illustrations or text.


D4119853A
●Handling Precautions (Camera Control Unit)
DANGER
Unplug
If any overheating sign is observed, discontinue the use immediately.
In the event that smoke, smell, or any other overheating sign is observed, turn its power
switch OFF immediately, and remove your plug from outlet. Do NOT try to continue to
use this device. To do so in spite of clear signs of malfunction invites a fire, an electric
shock hazard, or a serious damage. In such case, contact us or our dealer /distributor
from which you purchased this device for repair service.
Unplug
If any malfunctioning sign is observed, discontinue the use immediately.
Do NOT try to use this device when it is obviously malfunctioning. (Example: No
images on the monitor) In the event of malfunction, turn its power switch OFF
immediately, and remove the plug from the outlet. In such case, contact us or our dealer/

distributor from which you purchased this device for repair service.
Unplug
If any liquid gets into the device, discontinue the use immediately.
In the event that water, or any other type of liquid gets into the body, do
NOT try to continue to use the device. To do so invites a fire or an electric
shock hazard. In that case, turn its power switch OFF immediately, and then
remove the plug from the outlet. After that, contact us or our dealer/ distributor
from which you purchased this device for repair service/technical advice.
Unplug
If any foreign object gets into the body, discontinue the use immediately.
In the event that grits, small particles, or any other foreign
objects get inside, do NOT try to continue to use the device. To do so invites
a fire or an electric shock hazard. In that case, turn its power switch OFF
immediately, and then remove the plug from theoutlet. After that,contactus
or our dealer/distributor from which you purchased this device for
repair service/technical advice.
Unplug
If any outer strong impact is given to this device, discontinue the use immediately.
In the event that this device is dropped onto the ground, or its cabinet is
damaged, turn its power switch OFF immediately, and remove the plug from
the outlet. Do NOT try to continue to use the device. To do so invites
a fire or an electric shock hazard.
In such case, contact us or our dealer/distributor from which you purchased
this device for repair service.
NEVER
pull apart
Do NOT disassemble this device.
Do NOT attempt to pull apart, repair, or modify the device on your own.
To do so might lead to a fire or an electric shock accident.
Contact us or the dealer/distributor from which you purchased the device for
repair/modification.


D4119853A
Avoid
Do NOT supply any power other than specified.
This device is designed to work only under specified voltage. Do NOT
attempt to supply the device with power other than specified. Supplying
the device with unspecified power invites a fire or an electric shock hazard.
●Handling Precautions
DANGER
Avoid
Do NOT place the device unstably.
Do NOT place the device on an unstable table, sloped ground, etc.. Make sure that the
device do not fall nor roll over to prevent an accident.
Avoid
Do NOT place any potentially-hazardous things on this device.
Do NOT place any things on the device which may, if it gets into the inside of the body,
damage the inner parts of the device (such as a flower pot, glass, cosmetics, a container
filled with liquids or chemicals, as well as small metal parts, etc.). If tumbled, the
liquids inside the bottle, etc. may get into the chassis, causing a fire or an electric shock
accident.
Avoid
Do NOT insert any foreign object through air-vent
Avoid inserting any foreign object, especially metal part, combustible, through
ventilation slits. To do so may cause a fire or an electric shock accident.
Avoid
Do NOT damage the power cord.
Do NOT damage, break, re-
p
rocess, nor bend forcefully the power cord. Pulling
forcefully/Twisting/Placing a heavy object on/Applying heat on the cord should also be
avoided. Otherwise, the cord may be damaged, causing a fire or an electric shock
accident. If the cord is damaged, contact us or our dealer/distributor from which you
purchased this device for repair service.
Avoid
Do NOT remove the protective cover
Avoid removing its protective cover. If you touch the inner high-voltage part, you might
get an electric shock. For inner part/circuit checkup, maintenance, or repair, contact us
or the dealer/distributor from which you purchased this device.


D4119853A
●Handling Precautions
CAUTION
Unplug
Unplug the power-plug when the your device is not in use.
For safety, make sure to unplug the power-plug before you give your device a
cleanup, or when it is not used. Keeping the power-cord connected might invite
a fire or an electric shock hazard.
Avoid
Do NOT expose your device to direct sunlight, nor intensive heat.
Do NOT place this device where it is exposed to direct sunlight, or in a high
temperature condition. To do so may cause the inner temperature of the device to go up,
resulting in burning-down of inner parts, circuits or a fire accident.
Avoid
Do NOT attempt to make connection before turning power off
Make sure to check the CCU power is OFF before connection.
Otherwise, you might get an electric shock.
Avoid
Do NOT pull the cord itself
When disconnecting the power-plug out of the outlet, make sure to
hold the plug, and then pull it out. Do NEVER try to pull the cord itself. Otherwise, the
cord may be damaged or broken, leading to a fire or an electric shock accident.
Avoid
Do NOT handle the power cord with your hand in an wet condition.
Do NOT plug in/out the power cord with an wet hand. Otherwise, it
may cause an electric shock accident.

Avoid
Do NOT block ventilating slits.
You should avoid;
n Placing your device upside down, or with wrong side up.
n Installing your device in a poor natural draft condition, recessed area.
n Placing your device on carpet, cushion.
n Putting a tablecloth, curtain on your device.
Blocking the ventilation slits prevents inner heat from escaping, which might
lead to a fire accident.

Avoid
Do NOT place your device too close to a heater.
Do NOT place your device or its power cord too close to any heating appliance.
Otherwise, the coating of its switch and/or power-cord may melt, leading to a fire or
an electric shock accident.

Avoid
Do NOT use chemical solvent for cleanup.
When giving your camera a cleanup, avoid using a benzene, alcohol, and
thinner. These chemicals might cause its coating or markings to come off or
become degraded.


D4119853A
●Handling Precautions (Camera-head)
DANGER
NEVER pull
apart
Do NOT disassemble this device.
Do NOT attempt to pull apart, repair, or modify the device on your own. Todo
so might lead to a fire or an electric shock accident. Contact us or the
dealer/distributor from which you purchased the device for repair/modification.
CAUTION

Avoid
Do NOT connect/disconnect connectors before turning power off.
Make sure to check the CCU power is OFF before connecting/disconnecting
connectors. Otherwise, you might get an electric shock, or your camera
might break down.

Avoid
Do NOT expose your device to direct sunlight, nor intensive heat.
Do NOT place this device where it is exposed to direct sunlight, or in a
high temperature condition. To do so may cause the inner temperature of the
device to go up, resulting in burning-down of inner parts, circuits or a fire
accident.
●Handling Precautions (Camera Cable)
DANGER
NEVER pull
apart
Do NOT disassemble this device.
Do NOT attempt to pull apart, repair, or modify the device on your own. To d
o so might lead to a fire or an electric shock accident. Contact us or the
dealer/distributor from which you purchased the device for repair/modification.
CAUTION

Avoid
Do NOT connect/disconnect connectors before turning power off.
Make sure to check the CCU power is OFF before connecting/disconnecting
connectors. Otherwise, you might get an electric shock, or your camera
might break down.



D4119853A
RESTRICTION FOR USE
1. Avoid irregular signal interface.
Do not attempt irregular signal interface other than specified. Under signal interface
other than recommended/specified in this instruction manual, the device might fail to
exert the maximum performance. In much worse case, if you continue to use your device
under incorrect signal interface, part(s) of inner circuits might burn down.
DISCLAIMER (LIMITED WARRANTY)
We disclaim any responsibility and shall be held harmless for damages or losses incurred by user(s) in
either of the following cases.
1. In case damages or losses are caused by fire, earthquake, or other acts of Gods, the act by third party,
misuse by the user deliberately or erroneously, use under extreme operating conditions.
2. In case any indirect, additional, consequential damages (loss of expected interest, suspension of
business activities) are incurred as results of malfunction or non-function of this device, we shall be
exempted from assuming responsibility for such damages.
3. In case damages or losses are caused by incorrect use which is not in line with the instructions given in
this instruction manual.
4.In case damages or losses are caused by malfunction resulting from bad connection with other
equipment.
5.In case damages or losses are caused by repair or modification done by the user.
OTHER INSTRUCTIONS
Do NOT use power other than specified
Be sure to use DC12V power supply. The camera is designed to work only under the specified voltage.
Do NOT attempt to drive the camera with the power other than DC12V. Operating the camera under
power other than DC12V invites a fire or a electric shock hazard.
Avoid intensive light
Do NOT expose the camera’s image-pickup-plane to sunlight or other intense light directly. If the part of
CCD is exposed to spot-intensive light, you might get a picture problem like blooming and/or smear. You
might observe vertical stripes on your monitor if your camera is exposed to sunlight (or any other
intensive light), however, this is not a malfunction. Redirect your CH (camera-head) to different
directions in such case.
Use under right operation condition
This equipment is designed and guaranteed to work under the temperature range of 0 to 40 degrees C and
30 through 90% humidity range. Avoid using the equipment beyond that limits.
Handle with care
Take care not to drop the equipment, nor give strong impact, as this may cause breakdown.
Do NOT tamper with switches
Read this operation guide thoroughly before you touch switches and adjusters on the rear panel. Do
NEVER attempt to disassemble the camera and/or tamper with any inner switches, potentiometers, etc.


D4119853A
Avoid liquid
Avoid placing the camera where it is likely to be splashed with water or any other fluids. Operating the
camera with its inner parts/circuits in an wet condition might cause a damage or an electric shock
accident.
About camera cable
The connector of the camera cable is in “screw-coupling” lock structure. Improper cramping might cause
image noise. Be sure to give it a good cramping to avoid noise.
Camera cable connection/disconnection
Before connecting/disconnecting connectors, make sure to turn camera power OFF. Otherwise, your
camera might break down.
Avoid placing near TV/radio
This camera might cause an interference (e.g. noise) if used around radio / TV set. In such a case, change
the location of your camera (or radio / TV).
Abnormal operation
In the event that any abnormal condition is observed, turn the power switch OFF immediately. Do NOT
try to continue to use the camera. To do so reckless of visible signs of malfunction invites a fire, an
electric shock hazard, or any other serious damage to the camera. In such case, contact us or our
dealer/distributor from which you purchased the camera for repair service.

Thank you for purchasing CS4000B series television camera featuring compact and light weight.
To take best advantage and gain the most service from your camera, read this operation manual
carefully and thoroughly.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
This equipment should be used with DC12V. Do not use any other power source.
INFORMATION
This equipment generates and uses radio frequency energy and if not installed and used properly,
that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception. If does so, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient the receiving antenna;
Relocate this equipment with respect to the receiver;
Move this equipment away from the receiver;
If necessary, the user should consult the dealer or an experienced radio/television technician
for additional suggestions.


D4119853A
CONTENTS
Page
1. FEATURES 1
2. PRECAUTION 1
3.CAMERAHEAD&CAMARACABLE 2
4.CONSTITUTION 3
5.SPECIFICATION 3
6.CONNECTIONS 8
7.OPERATION 9
8. TROUBLE-SHOOTING GUIDE 12
9. EXTERNAL VIEW
SPECTRUM RESPONSE
CAMERA CONTROL UNIT
CAMERAHEAD
CAMERA CABLE
HOW TO FIXED A LENS TO SQURE TYPE CAMERA HEAD
CAMERA MOUNTING KIT(OPTION)





1
D4119853A
1. FEATURES
(1) Compact and light weight camera head.
(2) Equipped with AGC (Automatic Gain Control) which allows wide dynamic range from bright to
dark subjects.
(3) Equipped with RTS (Random Trigger Shutter) which allows free timing capture with stable SYNC.
(4) Available external SYNC (HD/VD, VS, SYNC) operation.
2. PRECAUTION
(1) This equipment should be used with DC12V only.
To prevent electric shocks and fire hazards, do not use any other power source.
(2) The CS4000 series are designed to be used with EIA B/W television signals.
It cannot be used for playback with a television of a different standard
(3) Please handle the equipment carefully.
(4) Do not point your camera lens directly into sunlight or strong artificial light.
This might cause irreparable damage to the image sensor.
Also, be sure to use the lens cap when the camera is not in use.
(5) Do not expose the camera unit to high temperatures. For example, do not place it near a stove for
long periods, or in direct sunshine or in a car in hot weather. Heat may cause some malfunction.
(6) Keep the camera clean. Dust can damage the camera and cause trouble in moving parts.
Take particular care to avoid the entry of sand or grit when changing the camera lens.
(7) Avoid jolting the equipment or exposing it to vibration.
(8) Never attempt to dismantle the equipment.
(9) Avoid folding or stretching the camera cable or other connection cable between equipment.
(10) When the cabinet is dusty, clean by gently wiping with a soft cloth. And avoid the use of
strong cleaning agents such as benzene or alcohol as they may damage the cabinet.














2
D4119853A
３．CAMERA HEAD $ CAMERA CABLE
The constitution (the combinations of the camera head and the camera cable) is as following.
Camera Head
Type name CCD
Size Appearance Lens mount Appearance of the
camera head Cameracable
CSH4200B
CSH4200BC
Type
1/2 φ17mm M15.5 P0.5 (male screw) Round type
3m(CPRC4000B-03)
5m(CPRC4000B-05)
Extension7m ：
(CPC4000B-07J)
CSH4300B
CSH4300BC
Type
1/3 φ12mm M10.5 P0.5 (male screw) Round type
3m(CPRC4000B-03)
5m(CPRC4000B-05)
Extension7m ：
(CPC4000B-07J)
CSH4301B
CSH4301BC
Type
1/3 φ12mm M10.5 P0.5 (male screw) Round type
Cable length 3m
(Direct wiring)
Extension7m ：
(CPC4000B-07J)
CSH4310BV-□□
CSH4310BCV-□□
Type
1/3 20×20mm M10.5 P0.5
(female screw) Square type
CSH4310BW-□□
CSH4310BCW-□□
Type
1/3 20×20mm M10.5 P0.5
(female screw) Square type
CSH4310BX-□□
CSH4310BCX-□□
Type
1/3 20×20mm M10.5 P0.5
(female screw) Square type
CSH4310BY-□□
CSH4310BCY-□□
Type
1/3 20×20mm M10.5 P0.5
(female screw) Square type
CSH4310BZ-□□
CSH4310BCZ-□□
Type
1/3 20×20mm M10.5 P0.5
(female screw) Square type
CSH4410BW-□□ Type
1/4 20×20mm M10.5 P0.5 (female screw)Square type
CSH4410BX-□□ Type
1/4 20×20mm M10.5 P0.5
(female screw) Square type
CSH4410BY-□□ Type
1/4 20×20mm M10.5 P0.5
(female screw) Square type
CSH4410BZ-□□ Type
1/4 20×20mm M10.5 P0.5
(female screw) Square type
Cable：
Direct wiring
Type name:
(view from rear)
(1) V：rear
(2) W：left
(3) X：under
(4) Y：right
(5) Z：upper
□□:･Cable length
(1) 03：3m
(2) 05：5m
Extension7m：
(CPC4000B-07J)


3
D4119853A
４．CONSTITUTION
(1) Cameracontrolunit 1
(2) Accessories Operationmanual 1
(3) Option
① Each camera head
② Camera cable：CPRC4000B-03(3m),-05(5m)
③ Extension camera cable：CPC4000B-07J(7m)
④ Power adapter：CA130C-01
⑤ Power cable（Both ends 12P connector）：3m, 5m, 10m
⑥ Cable for power supply（VIDEO,HD,VD，SYNC，WENOUT、TRIGINPUT）
⑦ Lens
⑧ For DC INPUT CONNECTOR
⑨ C mount Adapter
About the option part and EMC
This camera guarantee combination with option part .
EMC is not guarantee incase with use non-designate option part.
５．SPECIFICATIONS
(The FACTOR is combination CSH4200B with 3m camera cable when no display head type.)
(1) TV system
Btype EIA
BC type CCIR
(2)Imagesensor InterlineCCD
(CSH4200B) ICX418ALB
(CSH4200BC ) ICX419ALB
(CSH4301B) ICX408ALB
(CSH4301BC ) ICX409ALB
(CSH4310B□-□□) ICX408AL
(CSH4310BC□-□□) ICX409AL
(CSH4410B□-□□) ICX228AL
･Total Active pixel
(EIA)/(CCIR) 811(H)×508(V) / 795(H)×596(V)
･Active pixel
(EIA)/ (CCIR) 768(H)×494(V) / 752(H)×582(V)
･VideooutActivepixel
(EIA)/ (CCIR) 756(H)×485(V) / 742(H)×575(V)
･Pixel Size
(CSH4200B) 8.4×9.8μm
(CSH4200BC ) 8.6×8.3μm
(CSH4301B､CSH4310B□-□□) 6.35×7.4μm
(CSH4301BC､CSH4310BC□-□□)6.5×6.25μm

4
D4119853A
(CSH4401B□-□□) 4.75×5.55μm
･Active image area
(CSH4200B,CSH4200BC) 6.5×4.85mm(1/2Type)
(CSH4301B､CSH4310B□-□□) 4.8×3.6mm(1/3Type)
(CSH4301BC､CSH4310BC□-□□)
(CSH4401B□- □□) 3.65×2.74mm(1/4Type)
(3) Number of scanning lines
(EIA)/ (CCIR) 525 lines / 625 lines
(4)Scanningsystem 2 : 1 interlace
(5)Sync.System Internal/External automatic switch-over
(6)Aspectratio 4:3
(7) Illumination
･Standard
(CSH4200B,CSH4200BC) 100lx F5.6
(CSH4301B､CSH4310B□-□□ 150lx F5.6
CSH4301BC､CSH4310BC□-□□)
(CSH4401B□-□□) 300lx F5.6 GAIN:STD γ＝1.0
･Minimum
(CSH4200B, CSH4200BC) 0.5lx F5.6
(CSH4301B､CSH4310B□-□□ 0.7lx F5.6
CSH4301BC､CSH4310BC□-□□)
(CSH4401B□-□□) 1.5lx F5.6 GAIN:MAX､γ＝0.45
(8)Videooutput VS=1.0V(p-p)/75Ω,1line
DC/AC coupling (inner SW setting)
(9) Resolution
(EIA) H:570TVlines , V:485TVlines
(CCIR ) H:560TVlines , V:575TVlines
(10)GAINcontrol AUTO/STD/MANU(FrontpanelSWsetting)
Videolevelcanbeadjustableby｢GAIN｣
Potentiometerwhen MANU.
(11)Gamma ON(0.45)/OFF(1.0)SelectablebyrearDIPSWsetting
Initialfactorysetting:OFF(1.0)
(12)Whiteclip clip-level857±40mV(p-p):SYNC non-include
(13) S/N 50dB(p-p)/rms(standard) (GAIN=STD,γ=1.0)
(14) CCD integration mode Field/Frame storage (integration) by rear DIPSW setting
Initialfactorysetting:Fieldstorageintegration
(15)Powersource DC12V±10%(Ripple level: Less than10mV(p-p)
(16) Power consumption approx.400mA(DC12V)
(17) Scanning frequencies (Internal synchronization mode)
･Horizontal drive(H)
(EIA) /(CCIR) 14.31818MHz±100ppm/ 14.18750MHz±100ppm

5
D4119853A
･Vertical drive(V)
(EIA)/(CCIR) 59.94Hz±100ppm/ 50.0Hz±100ppm
(18)Externalsyncinput HD･VD/SYNC/ VS
･Input level
HD･VD,SYNC 2〜6V(p-p)
VS 1.0V(p-p)(Sync:0.3V(p-p))
･Inputimpedance High/75Ω､Selectable by rear SW setting
･Scanningsystem 2:1interlace
･Polarity Negative
･Frequency
(EIA) fH =15.734kHz±1%, fV =2fH/525
(CCIR) fH =15.625kHz±1%, fV =2fH/625
･Scanning lines
(EIA)/(CCIR) 525lines/625lines
･Phase different The difference in phase between the falling edge of VD
andthatofHDisshowninthefigurebelow.
1st fieldforEIA２nd FIELD for EIA
２nd FieldforEIA １st Field for CCIR
    t1＝0±5μs t2＝１／fH／2±5μs

(19) Trigger input
･Inputlevel VL=0〜0.5V､VH=2〜5V
･Input impedance High impedance
･Polarity Negative
･Pulsewith 2μs〜1/4s
(20) Output signal
①HD･VD
･Outputlevel HD:4.5V±0.5V(p-p)(on no-load condition)
VD:5.0V±0.5V(p-p)(on no-load condition)
・Scanningsystem 2:1interlace
・Polarity Negative
･Pulse width
(EIA) HD:6.36±1μs, VD:572±10μs
(CCIR) HD:6.41±1μs, VD:480±10μs
ｔ１ ｔ２
ＶＤ
ＨＤ

6
D4119853A
･Frequency
(EIA) fH:15.334kHz±100ppm, fV:2fH/525
(CCIR) f
H:15.625kHz±100ppm, fV:2fH/625
･Scanning line
(EIA)/(CCIR) 525line/625line
②CLOCK
･Outputlevel 2.0±0.3V(p-p)(on no-load condition)
･Frequency
(EIA) 14.31818MHz±100ppm(on no-load condition)
(CCIR ) 14.18750MHz±100ppm(on no-load condition)
③WEN On operate random shutter mode, WEN put out from the fall time of VD
tothefalltimeofVDunderputoutvideosignal..
・Polarity Positive
・Diagram The circuit is shown in the figure below
(21) Electronic shutter Shutter speed can set by front panel switch
Asfollow:
OFF,1/125,1/250,1/500,1/1000,1/2000,
1/4000,1/10000, flickerless
1FLD,2FLD,4FLD,6FLD,8FLD,10FLD
(slowspeedshuttermode)

(22) Random shutter RTS mode selection available
Mode1 Shutter‑speedswitchsetting Internal sync SYNC non-reset
Mode2 Shutter‑speedswitchsetting Internal sync SYNC non-reset
Mode3 Shutter‑speedswitchsetting Internal sync SYNC Reset
Mode4 Shutter‑speedswitchsetting Internal sync SYNC Reset
Mode5 Shutter‑speedswitchsetting Series ＨＤ， Series ＶＤ input SYNC non-reset
Mode6 Shutter‑speedswitchsetting  Series ＨＤ， Series ＶＤ input SYNC non-reset
Mode7 Shutter‑speedswitchsetting Series ＨＤ， One-pulse ＶＤ input SYNC non-reset
Mode8 Shutter‑speedswitchsetting  Series ＨＤ， One-pulse ＶＤ input SYNC non-reset

(23) Special shutter Usr-defined shutter-speed cued and timed by shutter
triggerandrestart/resetpulseinputON/OFF
selectableviarearpanelDIPSW.
(Initialfactorysetting:OFF)
WEN
2SC4176
51
10k
4700

7
D4119853A
(24) Restart Reset Restart Reset function available via rear DIP SW
selection.
(25) Lens Mount Special Mount, by each head specification.
(26) Mass Camera control unit: about 350g
(27) GND Circuit GND---Chassis: Electrically continuous
(28) EMI Conforms to EN50081-2
(29) Connector Pin Assignment
･Power/Video connector
・Compatible plug :HR10A-10P-12S(Manufactured HIROSE ELEC)
External syncPin
No. HD・VD VS/SYNC Restart Reset
Internal sync
１GND GND GND GND
２+12V +12V +12V +12V
３GND GND GND GND
４Video OUT Video OUT Video OUT Video OUT
５GND GND GND GND
６HD INPUT HD INPUT HD OUT (*１)
７VD INPUT VS/SYNC
INPUT
R.R INPUT VD OUT (*１)
８GND GND GND GND
９CLOCK OUT CLOCK OUT CLOCK OUT CLOCK OUT
１０ WEN OUT WEN OUT WEN OUT
１１ TRIG INPUT TRIG INPUT TRIG INPUT TRIG INPUT
１２ GND GND GND GND

*１HD･VD OUT is available via inner SW selection under internal sync operation.
(30) Ambient condition
･Performance assurance
Temperature ０℃〜４０℃
Humidity ２０〜８０％ (No condensing)
･Operation assurance
Temperature -1０℃〜5０℃
Humidity ２０〜８０％ (No condensing)
･Storage
Temperature -2０℃〜6０℃
Humidity ２０〜９５％ (No condensing)





8
D4119853A
6．CONNECTIONS
When install the CS4000B series camera to your system, you have to connect between Equipment.
(1)Typical connection(One sample)

9
D4119853A
(2) Camera control unit rear panel connector
①｢CAMERA｣connector
This connector is used to connect the camera head and the camera control unit
With the camera cable.
When inserting the connector, make sure to set the position of the coupling-guide
Properly, and screw it up tightly, If it is loose, it may cause noise.
②｢VIDEO｣connector
Composite video output come out from this connector which is employed BNC type.
③｢DC IN/VIDEO OUT｣connector
The alignment of the receptacle dip posts







７．Operation
(1) Front panel
 

①「ＰＯＷＥＲ」
Power ON/OFF switch. When power is turned on, the pilot lamp on the power switch
Will light.
②「ＳＨＵＴＴＥＲ」
･Toggle switch
High/OFF: High speed shutter mode and no shutter mode.
LOW/F/L:Slowspeedshuttermode,FL, Width of Shutter mode.
①
②
③④⑤⑥
⑦
⑧
⑨
⑩
⑪⑫１２terminals(male) (rear view)

10
D4119853A
･Rotary switch
(When set the toggle switch to High/OFF)
  ０：Ｓｈｕｔｔｅｒ ｏｆｆ
  １：１／１２５s
  ２：１／２５０s
  ３：１／５００s
  ４：１／１，０００s
  ５：１／２，０００s
  ６：１／４，０００s
  ７：１／１０，０００s

(When set the toggle switch to ＬＯＷ／Ｆ．Ｌ)
  ０：ＦＬ（ｆｌｉｃｋｅｒｌｅｓｓ）
  １：１／６０（ＣＣＩＲ：１／５０）
  ２：２ＦＬＤ
  ３：４ＦＬＤ
  ４：６ＦＬＤ
  ５：８ＦＬＤ
  ６：１０ＦＬＤ
７：①setting of pulse width
②Rear panel switch SMD1:ON, SMD2:ON
Restart Reset operation/ special shutter ･reset operation
③「ＧＡＩＮ ＣＯＮＴＲＯＬ」
･AUTO
When AGC (Automatic Gain Control) is to increase or decrease sensitivity electrically to
get the comfortable video level.
･STD
Normally, put it [STD] position. The gain is fixed.(0dB)
･MANU
If the illumination of the subject is not sufficient and the picture on the monitor is dark or
bright, set this switch to [MANU] position. And you can adjust the video level with the
knob of [GAIN].










11
D4119853A
(2)Rear panel


① 「ＳＥＬＥＣＴ」：This Switch set every kind of setting.
1：SMD１（Setting about Shutter mode）
 2：SMD2（Setting about Shutter mode）
3：TRIGON：NegativeOFF：Positive
4：Ccd integration mode ON：FIELDOFF：FLAME
5：Gamma(γ)ON：0.45OFF：1.0
 ６：Open

SMD1 SMD2 Operation
ON ON
Restart･Reset/Special shutter: Toggle switch set
LOW/F.L
ON OFF Mode 7, Mode 8
OFF ON Mode 3, Mode 4
OFF OFF Mode 1，Mode 2, Mode 5, Mode 6
*Refer to shutter specification about Mode.
 
②「ＨＤ ＶＤ  ＨＩＧＨ／７５Ω」
This switch switches external-sync input terminal 75-ohm termination ON/OFF.
When set in right side, the termination is 75-ohm. When set in left side,
the termination is 10k-ohm.The initial factory setting is in OFF position.
③ 「ＨＤ ＶＤ ＩＮ／ＯＵＴ」
This is the HD VD sync-signal IN/OUT selection switch. The state is HD VD IN
When set in left side, HD VD OUT when in right. The initial setting is IN.


