Telit Wireless Solutions BlueEva+SR Guide

Application Note
80507NT11470A, Rev. 02 –2016-05-26

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 2 of 10
BlueEva+SR
NFC Add-on Package
Release r02

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 3 of 10
Table of Contents
1Introduction .......................................................................................................4
2Requirements....................................................................................................4
3Add-on Package................................................................................................4
3.1 Package Contents.........................................................................................5
3.2 Hardware......................................................................................................5
3.3 Solder the pin strip........................................................................................6
3.4 Connect the NFC tag to the BlueEva+SR hardware......................................6
4BlueEva+SR Firmware Update (optional)..........................................................7
5Usage of NFC Handover ...................................................................................7
6History...............................................................................................................8

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 4 of 10
1 Introduction
This documentation describes the upgrade of the Bluetooth evaluation board
BlueEva+SR with NFC Handover.
2 Requirements
The BlueEva+SR NFC Add-on package is intended for customers who have
bought a BlueEva+SR hardware without NFC Handover feature in the past.
Figure 1: BlueEva+SR hardware without X3 connector (24 pin strip)
3 Add-on Package
Please use the following order number if you want to order the Add-on package
from Telit:
Order number: 53300-00

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 5 of 10
3.1 Package Contents
The NFC Handover Add-on package contains the following components:
1 x Pin strip (24 pins)
1 x NFC board “NTAGI2CEvalv1.0” including corresponding flat ribbon cable
3.2 Hardware
Figure 2: Pin strip (24 pins)
Figure 3: NFC tag with flat ribbon cable

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 6 of 10
3.3 Solder the pin strip
Please solder the pin strip carefully on top of the BlueEva+SR hardware and
avoid solder straps. Otherwise the NFC tag will not work correctly! The place
where the pin strip shall be soldered is labeled with “X3”. The pin strip has no
alignment so it is not possible to solder it in a wrong direction.
After soldering the pin strip it shall look as shown in the following picture.
Figure 4: BlueEva+SR with soldered pin strip
3.4 Connect the NFC tag to the BlueEva+SR hardware
Connect the NFC tag including the flat ribbon cable to the BlueEva+SR
hardware as shown in the following picture.
Figure 5: NFC tag connected to the BlueEva+SR

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 7 of 10
4 BlueEva+SR Firmware Update (optional)
The NFC Handover feature is supported since firmware version 1.502.
Please check if your BlueEva+SR includes at least this firmware version,
otherwise please update the firmware.
Please refer to the BlueEva+SR User Guide regarding firmware update.
http://www.telit.com/support/technical-support/
5 Usage of NFC Handover
Please refer to the BlueEva+SR User Guide regarding the usage of the NFC
Handover feature.
http://www.telit.com/support/technical-support/

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 8 of 10
6 History
Version
Release Date
By
Change description
r01
27.02.2015
NH
First release
r02
26.05.2016
BG
Telit cover page added

BlueEva+SR
NFC Add-on Package
Stollmann is a Telit brand.
Page 9 of 10
Telit Wireless Solutions GmbH
Mendelssohnstraße 15 D
22761 Hamburg
Germany
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
www.telit.com