Tenmars HB2TM102001 User manual

SOUND LEVEL METER
User's manual
/ qttgiF
iiS^#
i ftT#,
,ffi (€
HB2TM1 02001

CONTENTS
1. General Description & Specifications............ 1
2. Name and Funtions ................. 3
3. Calibration Procedures ............ 6
4. Measurement Preparation .................. .......... 7
5. Operating precautions .............7
6. Measurement................ ...........8
7. END OF 1lFE....... ....................8

TEi$vlAf:s TM-102
Thank you for using our Sound Level Meter.
To ensure that you can get the most from it, we
recommend that you read and follow the manual
carefully before use.
This unit conforms to the IEC 61672-1 class 2 standard ,
lEC651 Type2, ANSI 51.4 Type2 for Sound Level
Meters.
This Sound Level Meter has been designed to meet the
measurement requirements of safety Engineers, Health,
lndustrial safety offices and quality control in various
environments.
. Ranges from 30dB to 1 30dB at frequencies between
31 .SHZand 8 KHZ .
. Display with 0"1dB steps on a 4 digits LCD.
. With two equivalent weighted sound pressure levels,
A and C.
1. GENERAL DESCRIPTION &
SPECIFICATIONS
a. Display:4 digits LCD with maximum/minimum,
Resolution:0.1d8, Display Update:0.5 sec.
b. Standard applied:lEC 61672-1 class 2 standard and
lEC651 Type2, ANS|1.4 Type2.
Frequency range:31 .5Hz-BKHz.
Measuring level range:A Weighting 30 -130d8.
C Weighting 35-130d8.
Frequency weighting:A,/C.
Microphone:1/2 inch Electret condenser
microphone.
Time weighting:FAST(1 25mS),SLOW( 1 sec).
Level ranges:3O -1 3OdB(Auto Range).
?Elurtqttril* TM-102
i. Accuracy:+1.5d8.
j. Dynamic range:S0dB.
k. MM/MlN:Hold readings for the Maximum and
Minimum value.
l. DATA HOLD:The reading data shown on LCD can
be locked while pressing the button
m. Low Battery lndication: Replace battery as LCD
display "Etr".
n. Power Supply:9v NEDA 1604,1EC 6F22,JlS 006P
batteryx 1 P6s.
o. Power Life:About 50 hrs (alkaline Battery).
p. Operation height:2000M under the elevation above
sea level.
q. Operation temperature & Humidity:5'C-40"C,
below 80%RH "
r. Storage Temperature&Humidity:-10"C -60"C,
below 70%RH "
s. Dimension: 200mm(L)x55mm(W)x38mm(H).
t. Weight: About 1709. (lncluding batteries)
u. Accessories: lnstruction manual, carrying case ,
9V Battery, windscreen.
c.
d.
e.
f.
s.
h.
EN-1 EN.2

2. NAME AND FUNTIONS
.---@
!;
ir:
1. Windscreen
lf you operate at wind speed over 10m/sec, please
put protective accessories-windscreen in front of
the microphone.
TehFttAfEi TM_102
a. Low battery indicaiion
b.DATA HOLD
indication
c. Maximum indication
d.Minimum indication
e.A-Weighting
f. C-Weighting
g.Slow response
h.Fast response
i. Sound level read out
Power button.
The key for 'lsec to turn the sound level meter ON
or OFF. The auto power will be off automatically
after 5 minutes idle time
MAX/MlN hold button
Press MAXMIN button to enter the maximum and
minimum recording mode. Press once to select
MAX value. Press again to select MIN value,
Press again to exit the MAX/MIN mode.
Frequency Weighting select button.
A : A-Weighting. For general sound level
measurements. C:C-Weighting. For checking the
low-frequency content of noise.(lf the C-Weighted
level is much higher than the A-weighted level,
then there is a large amount of low-frequency
noise)
Time weighting select button.
FAST:for normal measurements.
SLOW:for checking average level of fluctuation
noise.
HOLD button.
EN-4
1.
2.
J.
4.
E
o.
7.
6-
9.
10.
11.
Windscreen
Display
DATA HOLD button
Frequency weighting
select button
Time weighting select
button
Maximum/Minimum hold
button
Backlight button
Power button
Microphone
Battery Cover
Tripod socket
1
J
6.
7.
Display
EN-3

8.
TElSTIAffi TM-102
The reading data shown on LCD can be locked
while pressing the button.
Backlight button.
Press the button you enable the display backlight
to easy readings in dark environments. Press
more than 1 second to disable backlight' which
however it automatically OFF after 15 seconds.
Microphone
112 inch Electret Condenser microphone.
Battery cover
TEl{rlAtlg TM-'102
3. CALIBRATION PROCEDURES
Using a standard Acoustic Calibrator(94dB,1KHz Sine
wave)
Acoustic calibrator
Sound level meter
Make the button settings. Display:dBA
Time weighting:FAST
lnsert the Microphone nozzle carefully into the
insertion hole of the calibrator.
Press A/C button then press the HOLD button, hold
the 2 buttons at the same time more than 1 second,
LCD will be blinking to confirm calibration.
When LCD blinked, release the A/C and the HOLD
bultons. The sound level meterwill display 94.0
dBA . The calibration is done.
EN-6
9.
10.
1.
2.
3.
4.
EN-5

1.
6,
1.
2
4.
4.
5.
1.
5.
7.
TEfr$llAff' TM-102
The 94 dB calibration process can be repeated until the
meter reads 94.0 dB. Recalibration cycle:1 year.
MEASU REMENT PREPARATION
Battery Loading
Remove the battery cover on the back and put in
one 9V Battery.
Battery Replacement When the battery voltage
drops below the operating voltage, the mark F?l
appears. lf it appears, battery should be replaced
with new one.
OPERATING PRECAUTIONS
Wind blowing across the microphone would bring
additional extraneous noise. Once using the
instrument in the presence of wind, it is necessary
to mount the windscreen preventing to pick up
undesirable signals.
To achieve more accurate measurement, use an
extension cable to separate the Microphone from
the main body so that the effect of unexpected
sound reflection can be eliminated.
Calibrate the instrument before operation if the
instrument was not in use for a long time or
operation at bad environment.
Do not store or operate the instrument at high
temperature and high humidity environment.
Keep microphone dry and avoid severe vibration.
Please take out the battery and keep the instrument
in low humidity environment. When it is not in use.
TeTwlAlll=; rM-102
MEASUREMENT
Open battery cover and install a 9 Volt battery in
battery compartment.
Turn on power and select the desired response
time and weighting. lf the sound source consists of
short bursts or only catching sound peak, set
response to FAST. To measure average sound
level, use the slow setting. Select A weighting for
general noise sound level and C weighting for
measuring sound level of acoustic material-
Hold the instrument comfortably in hand or fix on
tripod and point the microphone at the suspected
noise source, the sound pressure level will be
displayed.
When MAX MIN (maximum, minimum hold) mode
is chosen. The instrumeni captures and holds the
maximum or minimum noise level . Press once to
select MAX value. Press again to select MIN value,
Press again to exit the MAXMIN mode. "MAX" or "
MlN" symbol disappears.
Turn off the instrument and remove the battery
when it is not in use.
END OF LIFE
Caution: this symbol indicates that
equipment and its accessories shall be
subject to a separate collection and
correct disposal
J.
4.
5.
6. X
I
EN-B
EN-7