Tennant 3530 Product manual

ENGLISH - ESPAÑOL - FRANÇAIS
3530/3560/3580
Operator and Parts Manual
Manual De Operador
Y Lista De Repuestos
Opérateur Manuel et
Liste Des Piéces
607620
Rev. 03 (08-2007)
www.tennantco.com
Model Part No.:
607617 - 3530
607618 - 3560
607619 - 3580
9003129 - 3580
Wet/Dry Vacuum
Aspirador en seco y húmedo
Aspirateur à sec/humide
*607620*

2Tennant 3530/3560/3580 (07--02)
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
WARNING -To reduce the risk of fire, electric shock, or injury:
1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing.
2. Use indoors only. Always install float before any wet pick--up operation.
3. Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
4. Use only as described in this manual. Use only manufacturer’s recommended attachments.
5. Do not use with damaged cord or plug. If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water, return it to a service center.
6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away from
heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9 Do not put any object into openings. Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving
parts.
11. Turn off all controls before unplugging.
12. Use extra care when cleaning on stairs.
13. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas
where they may be present.
14. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
SAVE THESE INSTRUCTIONS

Tennant 3530/3560/3580 (07--02) 3
INSTRUCTIONS DE SÉCURITÉ
Deben observarse siempre instrucciones básicas de seguridad al usar artefactos eléctricos
incluyendo las siguientes:
LIRE TOUTES LES INSTRUCTIONS AVANT DE FAIRE FONCTIONNER (CET APPAREIL)
ADVERTISSEMENT - Pour réduire les risques d’incendie, de choc électrique ou de blessure:
1. Ne pas laisser l’appareil san surveillance lorsqu’il est branché. Débrancher lorsque
l’appareil n’est pas utilisé et evant l’entretien.
2. Utiliser á l’intererieur seulement. Installer un flotteur avant d’aspirer des matières humides.
3. Ne pas permettre aux enfants de jouer avec l’appareil. une attention particuliér est
nécessarie lorsque lappareil est utilisé par des enfants ou à proximite de ces deniers.
4. Nutiliser que conformément à cette notice avec les accessories recommandés par le
fabricant.
5. Ne pas utiliser si le cordon ou la fiche est endommagé. Retourner lappareil a un atelier
de réparation s’il ne fonctionne pas bien, s’il est tombé ou s’il a été endommage, oublie
à l’extérieur ou immergé.
6. Ne pas tirer soulever ou traîner l’appareil par le condon. Ne pas uliliser le cordon
comme une poignée, le coincer dans l’embrasure d’une porte ou l’appuyer contre des
arêtes vives ou des coins. Ne pas faire rouler l’appareil sur le cordon. Garder le cordon à
l’écart des surfaces chaudes.
7. Ne pas débracher en tirant sur le cordon. Tier plutôt la fiche.
8. Ne pas toucher la fiche ou l’appareil lorsque vos mains sont humides.
9. N’insérer aucun objet dans les ouvertures. Ne pas utiliser l’appareil losqu’une ouverture
est bloquée. S’assurer que de la poussière, de la peluche, des cheveuxou d’autres
matières ne réduisent pas le débit d’air.
10. Maintenir les cheveux, les vêtements amples, les doigts et toutes les parties du corps l’écart
des ouvertures et des piéces mobiles
11. Mettre toutes les commandes a’la postion ARRêT avant de de’brancher l’appareil.
12. User de prudence lors du nettoyage des escaliers.
13. Ne pas aspirer des liquides inflammables ou combustibles, comme de l’essence, et ne
pas faire fonctionner dans des endroits où peuvente se trouver de tels liquides.
14. Ne pas aspirer de matières en combustion ou qui dégagent de la furmée, comme des cigarettes,
des allumettes ou des dendres chaudes.
MANTENER ESTE INSTRUCCIONES

4Tennant 3530/3560/3580 (07--02)
CONSIGNES DE SÉCURITÉ IMPORTANTES
Lorsque vous utilisez un appareil électrique, des précautions de base doivent être respectées,
parmi lesquelles:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER CET APPAREIL
AVERTISSEMENT -Afin de réduire le risque d’incendie, de choc électrique ou de blessure :
1. Ne quittez pas l’appareil lorsqu’il est branché. Débranchez de la prise lorsque vous ne
l’utilisez pas et avant l’entretien.
2. Utilisez en intérieur uniquement. Installez toujours le flotteur avant une opération de ramassage en
milieu humide.
3. Ne laissez personne utiliser l’appareil comme un jouet. Une attention particulière est
nécessaire lorsque l’appareil est utilisé par ou près d’enfants.
4. Utilisez l’appareil uniquement comme décrit dans ce manuel. Utilisez uniquement les accessoires
recommandés par le fabricant.
5. N’utilisez pas l’appareil avec un câble électrique ou une prise endommagés. Si l’appareil ne
fonctionne pas convenablement, est tombé, a été endommagé, laissé à l’extérieur ou jeté
dans l’eau, renvoyez--le à un service de dépannage.
6. Ne tirez pas ou ne transportez pas par le cordon, n’utilisez pas le cordon comme une
poignée, ne fermez pas une porte sur le cordon, ne tirez pas le cordon sur des arêtes ou
coins tranchants. Ne roulez pas sur le cordon avec l’appareil. Eloignez le cordon des
surfaces chaudes.
7. Ne débranchez pas l’appareil en tirant sur le cordon. Pour débrancher l’appareil, attrapez la
prise, pas le cordon.
8. Ne manipulez pas la prise ou l’appareil avec des mains mouillées.
9 Ne placez pas d’objets dans les orifices. N’utilisez pas l’appareil lorsqu’ un orifice est bloqué;
maintenez à l’abri de la poussière, les peluches, les cheveux, ainsi que tout ce qui peut
réduire la circulation d’air.
10. Eloignez des ouvertures et des pièces mobiles les cheveux, les vêtements amples, les doigts
et toutes autres parties du corps.
11. Coupez toutes les commandes avant de débrancher l’appareil.
12. Soyez particulièrement prudent(e) lorsque vous nettoyez des marches d’escalier.
13. N’utilisez pas l’appareil pour ramasser des liquides inflammables ou combustibles tels que
l’essence ou dans des endroits où ces liquides peuvent être présents.
14. Ne ramassez pas de déchets enflammés ou fumants, comme des cigarettes, des allumettes ou
des cendres chaudes.
INSTRUCTIONS DE MISE A LA TERRE

Tennant 3530/3560/3580 (07--02) 5
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a
path of least resistance for electric current to reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment--grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING -- Improper connection of the equipment--grounding conductor can result
in a risk of electric shock. Check with a qualified electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do not modify the plug provided with
the appliance -- if it will not fit the outlet, have a proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120--volt circuit and has a grounding attachment plug that
looks like the plug illustrated in sketch. Make sure that the appliance is connected to an outlet
having the same configuration as the plug. No adaptor should be used with this appliance.
Grounded
3HoleOutlet
Ground Pin

6Tennant 3530/3560/3580 (07--02)
INSTRUCCIONES DE CONEXION A TIERRA
Este artefacto debe conectarse a tierra. Si funciona mal o se descompone, la conexión a tierra
provee una trayectoria de menor resistencia para la corriente eléctrica, para reducir el riesgo de
choque eléctrico. Este artefacto está provisto con un cordón que tiene un conductor de conexión
a tierra del equipo y un enchufe de conexión a tierra. El enchufe debe enchufarse a un
tomacorrientes apropiado que esté correctamente instalado y conectado a tierra de acuerdo con
todos los códigos y ordenanzas locales.
ADVERTENCIA: La conexión incorrecta del conductor de conexión a tierra del equipo
puede resultar en un riesgo de choque eléctrico. Consultar con un electricista calificado o
persona de servicio si existen dudas acerca de si el tomacorrientes está correctamente
conectado a tierra. No se debe modificar el enchufe provisto con el artefacto -- si no se
inserta en el tomacorrientes hacer que un electricista calificado instale un tomacorrientes
correcto.
Este artefacto es para usar en un circuito nominal de 120 voltios y tiene un enchufe de
aditamento para conectar a tierra que se parece al enchufe ilustrado en la figura. Asegurarse
que el artefacto esté conectado a un tomacorrientes con la misma configuración que el enchufe.
No se debe usar un adaptador con este artefacto.
ENCHUFE CONECTA-
DO A TIERRA
(3 ORIFICIOS)
CLAVIJADECONEXIONA
TIERRA

Tennant 3530/3560/3580 (07--02) 7
INSTRUCTIONS VISANT LA MISE ‘A LA TERRE
Cet appareil doit être mis à la terre. En cas de défaillance ou de panne éventuelles, la mise à la
terre fournit au courant un chemin de moindre résistance qui réduit le risque de choc électrique.
Cet appareil est pourvu d’un cordon muni d’un conducteur de terre et d’une fiche avec broche de
terre. La fiche doit être branchée dans une prise appropriée correctement installée et mise à la
terre conformément aux règlements et ordonnances municipaux.
AVERTISSEMENT. Un conducteur de terre mal raccordé peut entraîner un risque de choc
électrique. Consulter un électricien ou un technicien d’entretien qualifié si vous n’êtes pas
certain que la prise est correctement mise à la terre. Ne pas modifier la fiche fournie avec
l’appareil -- si elle ne peut être insérée dans la prise, faire installer une prise adéquate par
un électricien qualifié.
Cet appareil est destiné à un circuit de 120 v et est muni d’une fiche de mise à la terre semblable à
celle illustrée par le croquis. S’assurer que l’appareil est branché à une prise de courant ayant la même
configuration que la fiche. Aucun adaptateur ne devrait être utilisé avec cet appareil.
Priseà3trous
reliéeàlaterre
Fichedeterre

OPERATION
8Tennant 3530/3560/3580 (08--07)
This manual is furnished with each new model.
It provides necessary operation and maintenance
instructions and an illustrated parts list.
Read this manual completely and understand the
machine before operating or servicing it.
When ordering replacement parts, use the illustrated
parts lists section in this manual. Before ordering parts
or supplies, be sure to have your machine model
number and serial number available. Parts and
supplies may be ordered by phone or mail from any
authorized parts and service center, distributor or from
any of the manufacturer’s subsidiaries.
This machine will provide excellent service. However,
the best results will be obtained at minimum costs if:
SThe machine is operated with reasonable care.
SThe machine is maintained regularly - per the
machine maintenance instructions provided.
SThe machine is maintained with manufacturer
supplied or equivalent parts.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,
old machine components such as
batteries, hazardous fluids such as
antifreeze and oil, in a safe
environmentally way according to your
local waste disposal regulations.
Always remember to recycle.
Tennant Company
PO Box 1452
Minneapolis, MN 55440
Phone: [phone] or (763) 513--2850
www.tennantco.com
E1999, 2002, 2006, 2007 Tennant Company. All rights reserved.
Printed in U.S.A.
Specifications and parts are subject to change without notice.
MACHINE DATA
Please fill out at time of installation for future reference.
Model No.-
Install. Date -
Serial No.-

OPERATION
Tennant 3530/3560/3580 (08--07) 9
TABLE OF CONTENTS (ESPAÑOL....21) (FRANÇAIS....33)
SAFETY PRECAUTIONS 10....................
GROUNDING INSTRUCTIONS 10...........
SAFETY LABEL 11............................
MACHINE COMPONENTS 12...................
MACHINE INSTALLATION 13...................
MACHINE CONTENTS 13...................
ATTACHING HANDLE 13....................
ATTACHING OPTIONAL SQUEEGEE KIT 13..
MACHINE SETUP 14..........................
WET VACUUMING 14......................
DRY VACUUMING 15.......................
MACHINE OPERATION 15.....................
OPERATING ACCESSORY TOOLS 15.......
OPERATING SQUEEGEE KIT OPTION 15....
VACUUM MOTOR THERMAL PROTECTOR 16
DRAINING RECOVERY TANK 16................
FLOOR DRAINING 16......................
ELEVATED DRAINING 16...................
MACHINE MAINTENANCE 17..................
DAILY MAINTENANCE 17..................
WEEKLY MAINTENANCE 18................
MONTHLY MAINTENANCE 18...............
QUARTERLY MAINTENANCE 18............
STORING MACHINE 18........................
RECOMMENDED STOCK ITEMS 18.............
TROUBLE SHOOTING 19......................
SPECIFICATIONS 20..........................
MACHINE DIMENSIONS 20....................
ELECTRICAL DIAGRAM 47....................
PARTS LIST 48...............................
TANK GROUP 48..........................
BASE & HANDLE GROUP
(NON PUMP--OUT) 50.....................
BASE & HANDLE GROUP (PUMP-OUT) 52...
OPTIONAL ACCESSORIES 54..................
SQUEEGEE ASSEMBLY GROUP 54.........
WET/DRY TOOL KIT 56.....................
DRY TOOL KIT 57..........................
STANDARD FLOOR TOOL KIT 58...........
WET PICK-UP TOOL KIT 59.................

OPERATION
10 Tennant 3530/3560/3580 (07--02)
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is
suited for wet/dry vacuuming in an indoor environment
and is not constructed for any other use. Use only
recommended accessory tools.
All operators must read, understand and practice
the following safety precautions.
The following safety alert symbol/words are used
throughout this manual as indicated in their
description.
WARNING: To warn of hazards or unsafe
practices which could result in severe personal
injury or death.
FOR SAFETY: To identify actions which must be
followed for safe operation of equipment.
The following information signals potentially dangerous
conditions to the operator or equipment:
FOR SAFETY:
1. Do not operate machine:
-- Unless trained and authorized.
-- Unless operator manual is read and
understood.
-- In flammable or explosive areas.
-- Unless cord is properly grounded.
-- With damaged cord or plug.
-- If not in proper operating condition.
-- In outdoor areas.
-- In standing water.
-- Without bag and/or filters in place.
-- With the use of additional extension cords.
Only use manufacturer’s extension cord
equipped with machine which has proper
capacity and is grounded.
2. Before operating machine:
-- Make sure all safety devices are in place
and operate properly.
3. When using machine:
-- Do not run machine over cord.
-- Do not pull machine by plug or cord.
-- Do not pull cord around sharp edges or
corners.
-- Do not unplug by pulling on cord.
-- Do not stretch cord.
-- Do not handle plug with wet hands.
-- Keep cord away from heated surfaces.
-- Do not pick up burning or smoking debris,
such as cigarettes, matches or hot ashes.
-- Report machine damage or faulty
operation immediately.
4. Before leaving or servicing machine:
-- Turn off machine.
-- Unplug cord from wall outlet.
5. When servicing machine:
-- Unplug cord from wall outlet.
-- Use manufacturer supplied or approved
replacement parts.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Unplug machine before
servicing.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
GROUNDING INSTRUCTIONS
Machine must be grounded. If it should
malfunction or breakdown, grounding provides a
path of least resistance for electrical current to
reduce the risk of electrical shock. This machine
is equipped with a cord having an
equipment--grounding conductor and grounding
plug. The plug must be plugged into an
appropriate outlet that is properly installed in
accordance with all local codes and ordinances.
Do not remove ground pin; if missing, replace
plug before use.
Grounded
3HoleOutlet
Ground Pin

OPERATION
Tennant 3530/3560/3580 (11--06) 11
SAFETY LABEL
The safety label appears on the machine in the location indicated. Replace label if it is missing or becomes damaged
or illegible.
WARNING LABEL -- Located on top of machine.

OPERATION
12 Tennant 3530/3560/3580 (08--07)
MACHINE COMPONENTS
9
2
10
38
7
4
5
6
1
11
1. Tank
2. Cover
3. Drain Hose
4. Caster, Swivel
5. Squeegee (Optional)
6. Vacuum Hose (Optional)
7. Handle
8. Switch, On/Off
9. Power Cord
10. Filter Housing
11. Squeegee Lift Pedal (Optional)

OPERATION
Tennant 3530/3560/3580 (07--02) 13
MACHINE INSTALLATION
Check carton for signs of damage. Report damages
to carrier immediately.
Check machine contents list, contact distributor for
missing items.
MACHINE CONTENTS
1 -- 3m (10 ft) vacuum hose -- for accessory tools
1 -- Cloth bag
1 -- Paper bag
1 -- 15m (50 ft) power cord
NOTE: Squeegee and Accessory Tool Kits are sold
separately. See Optional Accessories.
ATTACHING HANDLE
1. Remove handle from ship position. Also remove
upper handle mounting screws and washers from
machine(Figure1).
Handle
(4) Screws
w/Washers
Cord Grip
Exhaust Hose
FIG. 1
2. Realign handle as shown and replace screws and
washers.
3. Push excess cord slack up into cord grip. Tighten
cord grip with 5/16 inch wrench until cord is
secure. DO NOT overtighten.
4. Connect exhaust hose to bottom of handle
housing.
ATTACHING OPTIONAL SQUEEGEE KIT
See Optional Accessories.
1. Empty recovery tank.
2. Remove vacuum bag.
3. Tip machine on back.
4. Remove (2) bolts and washers located at bottom
of machine.
5. Install squeegee mounting bracket with bolts and
washers (Figure 2).
FIG. 2
6. Fasten squeegee to mounting bracket. Use (2)
clevis and cotter pins provided (Figure 3).
FIG. 3
7. Stand vacuum upright.
8. Insert spacer through hole in pedal as shown.
Position pedal between two holes in bracket and
slide hex head screw through bracket and pedal.
Secure with washer and nut (Figure 4).
FIG. 4

OPERATION
14 Tennant 3530/3560/3580 (08--07)
9. Slide pedal between two mounting arms on back
of machine. Align and insert clevis pin through
arms and slot in pedal, secure with cotter pin
(Figure 5).
FIG. 5
10. Attach squeegee assembly to bracket. Use (2)
thumb screws to secure (Figure 6).
FIG. 6
11. Connect 117 cm (46 in) vacuum hose to squeegee
assembly and to neck on machine lid (Figure 7).
FIG. 7
MACHINE SETUP
1. Connect 15m (50 ft) power cord to machine pigtail
cord.
2. Plug power cord into a grounded outlet (Figure 8).
Grounded
3HoleOutlet
Ground Pin
FIG. 8
FOR SAFETY: Do not operate machine with the
use of additional extension cords. Only use
manufacturer’s extension cord equipped with
machine which has proper capacity and is
grounded.
WET VACUUMING
1. Open machine cover and remove vacuum bag
from recovery tank (Figure 9).
FIG. 9
2. Make sure automatic float shut-off screen is in
place (Figure 10).
FIG. 10

OPERATION
Tennant 3530/3560/3580 (07--02) 15
ATTENTION: To prevent vacuum motor damage,
automatic float shut-off screen must be in place.
DRY VACUUMING
1. Open vacuum machine cover and install cloth filter
bag, make sure that the bag edge is properly
seated on compartment rim (Figure 11).
For easy debris disposal and to prolong cloth bag
life, use a paper vacuum bag inside the cloth bag.
Tuck the top of paper bag around outside rim of
cloth bag. Never use paper bag without cloth filter
bag in place. Do not reuse paper bags -- always
dispose (Figure 11).
FIG. 11
FOR SAFETY: Do not operate machine without
bag and/or filter in place.
2. Close cover and fasten latches.
3. Leave automatic float--off screen in place when
dry vacuuming. It can provide limited vacuum
motor protection for a faulty bag.
MACHINE OPERATION
FOR SAFETY: Do not operate machine unless
operator manual is read and understood.
Perform MACHINE SETUP instructions before operating
machine.
WARNING: Flammable materials or reactive
metals can cause an explosion or fire. Do not pick
up.
OPERATING ACCESSORY TOOLS
1. Connect 3m (10 ft) vacuum hose to machine cover
snout.
2. Select desired accessory tool and connect to
vacuum hose (Figure 12).
FIG. 12
3. Activate ON/OFF switch and operate accessory
tool as normal.
4. During DRY vacuuming, check bag periodically for
fullness. For best suction performance, empty bag
at 3/4 full.
During WET vacuuming, the float shut-off screen
will automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If foam develops in recovery tank
during wet vacuuming, use a quality defoamer
chemical to eliminate the foam. Foam buildup will
NOT activate float, and will cause damage to the
vacuum motor. Damage due to foam is NOT
covered by warranty.
OPERATING SQUEEGEE KIT OPTION
1. Lower squeegee to floor, lightly kick the pedal
forward to release from transport position
(Figure 13).
FIG. 13

OPERATION
16 Tennant 3530/3560/3580 (07--02)
2. Activate the ON/OFF switch.
3. Begin operating by pushing and pulling machine in
either direction.
4. During operation, the float shut-off screen will
automatically stop water intake when recovery
tank becomes full (See DRAINING RECOVERY
TANK).
ATTENTION: If foam develops in recovery tank
during wet vacuuming, use a quality defoamer
chemical to eliminate the foam. Foam buildup will
NOT activate float, and will cause damage to the
vacuum motor. Damage due to foam is NOT
covered by warranty.
5. To raise squeegee, step downward on pedal until
pedal engages in the transport position
(Figure 14).
FIG. 14
NOTE: Squeegee Kit can be used to pick up fine
particles (dust, sand, sawdust, etc.). Squeegee not
recommended for ordinary dry pick up.
VACUUM MOTOR THERMAL PROTECTOR
Vacuum motor is thermally protected by a temperature
sensor device. It will trip if motor has an overload. If
motor should quit, wait 20 minutes for motor to cool
and remove obstruction before continuing.
DRAINING RECOVERY TANK
FLOOR DRAINING
1. Push machine to nearest floor drain, if not
available use a bucket to drain machine.
2. Remove drain hose from holder, twist off drain
hose knob and drain. Raise hose to stop flow of
water (Figure 15).
FIG. 15
3. After draining recovery tank, open cover and
thoroughly rinse out tank with clean water.
4. Replace drain hose knob securely and return to
holder.
ATTENTION: Be certain drain hose knob is secure
to prevent suction loss.
ELEVATED DRAINING
NOTE: Machine must be equipped with pump--out
feature.
1. Disconnect vacuum hose from attachment tool or
from squeegee attachment.
2. Disconnect exhaust hose from rear of machine
and connect it to vacuum hose (Figure 16).
FIG. 16

OPERATION
Tennant 3530/3560/3580 (07--02) 17
3. Hang drain hose elbow over edge of drain sink
(Figure 17).
FIG. 17
4. Pull up on drain lever and turn on switch
(Figure 18).
FIG. 18
5. Vacuum motor will pressurize tank and force
waterupintodrainsink.
MACHINE MAINTENANCE
To keep machine in good working condition, simply
follow machine’s daily, weekly and monthly
maintenance procedures.
WARNING: Hazardous Voltage. Shock or
electrocution can result. Unplug machine before
servicing.
DAILY MAINTENANCE
(Every 4 Hours of Use)
1. Drain and rinse recovery tank after wet
vacuuming.
2. Remove and clean float shut--off screen from
recovery tank (Figure 19).
FIG. 19
3. Clean squeegee blades with a cloth. Replace
blades when they become worn.
4. Check bag for fullness, empty bag at 3/4 full.
5. Wipe machine housing with a nonabrasive,
nonsolvent cleaner.
6. Check cords and cord grips for damage. If worn or
damaged, replace immediately. Coil cord neatly.
ATTENTION: Always have float shut--off screen in
place before operating. During wet operation, the
shut--off float protects the vacuum motor from
water. During dry vacuuming, the float screen can
provide limited protection for a faulty filter bag.
7. Inspect vacuum hose regularly for holes, loose
cuff or clogged debris.

OPERATION
18 Tennant 3530/3560/3580 (07--02)
WEEKLY MAINTENANCE
(Every20HoursofUse)
To maintain maximum performance, wash cloth filter
bag by hand with a mild detergent. Let bag dry
thoroughly before replacing.
MONTHLY MAINTENANCE
(Every80HoursofUse)
1. Lubricate axle grease fittings with a water resistant
grease.
2. Lubricate front swivel caster with a silicone spray.
3. Check machine for loose nuts and bolts.
QUARTERLY MAINTENANCE
(Every 250 Hours of Use)
Check motor for carbon brush wear, replace brushes if
worn to 10mm (0.38 in) or less.
Contact an Authorized Service Center for motor
maintenance.
STORING MACHINE
Before storing the machine perform the following
instructions:
1. Empty and rinse recovery tank and accessory
tools.
2. Empty or replace vacuum bag.
3. Raise or remove squeegee assembly, if equipped.
4. Store machine in a dry area in the upright position.
ATTENTION: Do not store outdoors and avoid
getting wet. Do not allow machine to freeze.
ATTENTION: If storing machine in freezing
temperatures, be certain to drain machine of all
water. Damage due to freezing is not covered by
warranty.
RECOMMENDED STOCK ITEMS
Refer to the Parts List section for recommended stock
items. Stock Items are clearly identified with a bullet
preceding the parts description. See example below:

OPERATION
Tennant 3530/3560/3580 (07--02) 19
TROUBLE SHOOTING
PROBLEM CAUSE SOLUTION
Machine does not run. ON/OFF switch is OFF. Turn switch to ON.
Vacuum not plugged into wall outlet. Plug power cord to wall outlet.
Faulty ON/OFF switch. Replace switch.
Faulty wiring. Contact Service Center.
Faulty power cord. Contact Service Center.
Building circuit breaker tripped. Reset circuit breaker and change to a
different power circuit.
Vacuum motor over heated. Find air obstruction. Let motor cool for 20
minutes.
Faulty vacuum motor. Contact Service Center.
Machine has little or no
suction.
Machine with Pump--Out
feature:
Hose is clogged. Clear hose.
Holes in hose. Replace hose.
Intake elbow in lid is clogged. Remove hose from elbow and remove
clogged material.
Drain hose knob is loose or open. Tighten drain knob.
Lid is not securely latched. Latch both sides of lid securely.
Worn gasket which is leaking air. Inspect all gaskets, and replace if
necessary.
Recovery tank or bag is full. Empty tank or bag.
Drain valve is open. Close drain valve.
Drain hose elbow is loose or off plug. Connect elbow to plug securely.
Squeegee has poor pick
up. Debris is wedged under squeegee blade. Wipe off squeegee blades.
Squeegee blades are worn. Replace squeegee blades.
Squeegee blade is loose. Tighten thumbscrews.
Vacuum hose connection on squeegee
mount is loose. Push vacuum hose onto squeegee mount securely.

OPERATION
20 Tennant 3530/3560/3580 (07--02)
SPECIFICATIONS
MODEL 3530 3560 3580
LENGTH 76.2 cm (30 in) 76.2 cm (30 in) 76.2 cm (30 in)
WIDTH 50.8 cm (20 in) 50.8 cm (20 in) 50.8 cm (20 in)
HEIGHT 88.9 cm (35 in) 88.9 cm (35 in) 88.9 cm (35 in)
WEIGHT 28.58 kg (63 lb) 28.58 kg (63 lb) 29.03 kg (64 lb)
VACUUM MOTOR 8.5 A, 1.3 hp.,
120V, 980 watts 10 A, 1.57 hp., 120V, 1200 watts 10.7 A, 1.6 hp., 120V, 1253 watts
POWERCORDLENGTH 15 m (50 ft) 15m (50 ft) 15m (50 ft)
OPTIONAL SQUEEGEE PATH WIDTH 685mm (27 in) 685mm (27 in) 685mm (27 in)
864mm (34 in) 864mm (34 in) 864mm (34 in)
1016mm (40 in) 1016mm (40 in) 1016mm (40 in)
WATER LIFT 233.68 cm (92 in) 289.56 cm (114 in) 271.78 cm (107 in)
TANK CAPACITY 60.57L (16 gal) 60.57L (16 gal) 60.57L (16 gal)
MACHINE DIMENSIONS
88.9 cm
(35 in)
50.8 cm (20 in)
(See Specifications Chart)
Optional Squeegee
76.2 cm (30 in)