Tennant T16 Training manual

IB 9007961 (08- 2015) 1
INSTRUCTION BULLETIN
No. 9007961
Machine: T16
Published: 08- 2015
Rev. 01
NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the
Parts List in the appropriate place in the machine manual for future
reference. Retaining the Parts List will make it easier to reorder
individual parts and will save the cost of ordering an entire kit.
NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.
Installation instructions for kit number 9008135
SYNOPSIS:
This kit contains the parts needed to install a strobe light kit on T16 scrubbers equipped with overhead
guards.
Please follow step-by-step instructions.
SPECIAL TOOLS / CONSIDERATIONS: NONE
(Estimated time to complete: 1.25 hours)
PROTECT THE ENVIRONMENT
Please dispose of packaging materials, used machine components
such as batteries and fluids in an environmentally safe way according
to local waste disposal regulations.
Always remember to recycle.
PREPARATION:
1. Park the machine on a clean level surface,
turn off the machine, and remove the key.
FOR SAFETY: Before leaving or servicing
machine, stop on level surface, turn off
machine, and remove key.
2. Disconnect the battery cables from the
batteries.
WARNING: Always disconnect battery
cables from machine before working on
electrical components.

IB 9007961 (08- 2015)2
INSTALLATION:
NOTE:Complete Step 1 through Step 5 only if
machine is not equipped with a front headlight.
Proceed to Step 6 if machine is equipped with
optional front headlight.
1. Carefully remove the instrument panel from
the machine. Do not break any wire
connections. Set the hardware aside. (Fig. 1)
2. Remove the hole plug from the instrument
panel. Discard the hole plug. (Fig. 1)
3. Insert the rocker switch (12) into the
instrument panel where the hole plug was
previously located. (Fig. 1)
4. Connect the main wire harness to the rocker
switch (12). (Fig. 1)
5. Reinstall the instrument panel onto the
machine. (Fig. 1)
Remove and
discard hole plug
Instrument
panel
12
FIG. 1

IB 9007961 (08- 2015) 3
6. Crimp the bullet terminals (11) onto the strobe
light (1) wires. (Fig. 2)
7. Insert the rubber grommet (8) into the hole in
the overhead guard. (Fig. 2)
8. Route the strobe light (1) wires down through
the rubber grommet (8) installed in the
overhead guard. (Fig. 2)
9. Use two M5 pan screws (2), two flat washers
(3), and two hex nuts (4) to install the strobe
light (1) onto the overhead guard. (Fig. 2)
10. Use two M6 hex screws (6) and two flat
washers (7) to install the light guard (5) onto
the overhead guard. (Fig. 2)
1
2
3
4
5
6
7
8
9
10
10
11
11
9
Connect to main
wire harness
FIG. 2

IB 9007961 (08- 2015)4
11. Connect the overhead guard light wire
harness (9) to the main wire harness. (Fig. 2 /
Fig. 4)
12. Route the overhead guard light wire harness
(9) up to the strobe light (1) and connect the
harness to the strobe light. (Fig. 2 / Fig. 4)
13. Use three cable tie mounts (13) and three
cable ties (14) to secure the overhead guard
light wire harness (9) to the overhead guard.
(Fig. 3)
14. Use the larger cable ties (10) to secure the
overhead guard light wire harness (9) to the
overhead guard leg. (Fig. 2)
FIG. 3
FIG. 4

IB 9007961 (08- 2015) 5
15. Remove the hardware holding the electrical
panel to the machine. Set the hardware aside.
(Fig. 5)
FIG. 5
16. Carefully remove the electrical panel from the
machine. Take care to not break any cable /
wire connections when removing the panel.
17. Remove the blanks from the CB13 and CB11
locations on the electrical panel. (Fig, 6)
FIG. 6
18. Install a 2.5- Amp circuit breaker (16) and a
circuit breaker boot (17) into electrical panel
CB13 location. (Fig, 7)
FIG. 7
19. Install a 15- Amp circuit breaker (15) and a
circuit breaker boot (17) into electrical panel
CB11 location. (Fig, 7)
20. Connect the main wire harness to the 2.5
Amp circuit breaker (16) and 15- Amp circuit
breaker (15) installed in the previous steps.
(Fig.7/Fig.8)
21. Reinstall the electrical panel onto the
machine.
22. Reconnect the battery cables to the batteries.
23. Start and test the machine. Place the light
switch into the top position and ensure the
strobe light is functioning.
FIG. 8

IB 9007961 (08- 2015)6
FIG. 9

IB 9007961 (08- 2015) 7
Bill Of Materials For Light Kit, Strobe, OHG, CI [T16] - 9008135
Ref.
Tennant
Part No. Description Qty.
o9008135 Light Kit, Strobe, OHG, CI [T16] 1
Yo1 1017250 Light, Strobe, Amb, 12- 48VDC 1
YY 9000845 Lamp, Bulb, Strobe 1
YY 9000879 Lens, Amb, F/ Revl / Flasher 1
Y2 06933 Screw, Pan, Phl, M5 X 0.80 X 16, 4.8 2
Y319066 Washer, Flat, 0.25b 0.56d .05, Pl, 10 2
Y4 06549 Nut, Hex, Lock, M5 X 0.80, Nl 2
Y5 1039392 Guard, Light, Revl / Strobe 1
Y6 74455 Screw, Hex, M6 X 1.00 X 12, Fmg 2
Y7 32490 Washer, Flat, 0.25, Std 2
Y810632- 2 Grommet, Rbr, 0.62id, F/0.9h, .12 Matl 1
Y9 1058141 Harness, Wire, Light, OHG [T16] 1
Y10 130773 Tie, Cable, Nyl, 11.0l, .14w, 3.0 Max. D 5
Y11 55272 Terminal, Bullet, Mal, .157D, 12GA 1
Y12 377084 Switch, Rocker, Prgrsv 1
Y13 55248 Mount, Cable Tie 3
Y14 49266 Tie, Cable, Nyl, 07.3L .19W 1.8 Max D 3
Y15 1064188 Circuit Breaker, 15.0a, Resettable 1
Y16 1064184 Circuit Breaker, 02.5a, Resettable 1
Y17 1064191 Boot, Circuit Breaker 2
TENNANT COMPANY
P. O. Box 1452
Minneapolis, MN 55440-1452