Terratec Phase 26 usb User manual

TERRATEC PRODUCER/PHASE 26 USB

English Manual

Version 1.1, November 2003

CE Declaration

We:

TerraTec Electronic GmbH, Herrenpfad 38, D-41334 Nettetal, Germany

hereby declare that the product:

PHASE 26 USB,

to which this declaration refers are in compliance with the following standards or stan-

dardizing documents:

EN 50013, EN 50022

The following are the stipulated operating and environmental conditions for said compli-

ance:

residential, business and commercial environments and small-company environments.

This declaration is based on:

Test report(s) of the EMC testing laboratory

The information in this document is subject to change without notice and shall not be deemed as a

warranty by the seller. No warranties, express or implied, are made with regard to the quality,

suitability or accuracy of this document. The manufacturer reserves the right to change the contents

of this document and/or the associated products at any time without the provision of prior notice to

specific persons or organizations. The manufacturer shall not be held liable for damages of any

kind arising from the use, or the inability to use this product or its documentation, even if the

possibility of such damage is known. The information in this document is subject to copyright. All

rights are reserved. No part of this manual may be reproduced or transmitted in any form or for any

purpose without the express written permission of the copyright holders. Product and brand names

contained in this document are used for identification purposes only. All registered trademarks,

product designations or brand names used in this document are the registered property of their

respective owners.

2 PHASE 26 USB (English)

Contents

From unpacking the PHASE 26 to installing it. ................................................................ 7

Scope of delivery...................................................................................................... 7

The operating modes................................................................................................... 7

Windows installation—step by step. ................................................................................ 9

Installing the PHASE 26 USB Driver for Windows 2000. ........................................... 11

Installing the PHASE 26 USB Driver for Windows XP................................................ 13

The PHASE 26 USB as a system audio device (Windows). .......................................... 16

Updating the firmware (Windows).............................................................................. 16

MAC installation—step by step...................................................................................... 17

Driver installation. ...................................................................................................... 17

Installing the ASIO under OS9. .............................................................................. 17

Installation under OS X. ......................................................................................... 17

Updating the firmware (MAC OS X). ...................................................................... 18

The connections of the PHASE 26 USB System. .......................................................... 20

Analog outputs........................................................................................................... 21

Analog inputs............................................................................................................. 22

Digital Interface (S/PDIF)........................................................................................... 24

MIDI interface. ........................................................................................................... 25

The Windows drivers..................................................................................................... 26

The MME Wave driver. .............................................................................................. 26

The ASIO driver and the PHASE-ASIO ControlPanel. ............................................... 26

The USB settings: .................................................................................................. 28

The ASIO settings:................................................................................................. 28

The Controls settings: ............................................................................................ 30

The MIDI driver. ..................................................................................................... 31

In detail—special properties of the drivers. ................................................................ 32

DirectSound & WDM. ............................................................................................. 32

WDM sample rate (SR) interpolation...................................................................... 32

WDM kernel streaming........................................................................................... 32

The MAC OS 9 drivers. ................................................................................................. 33

The MAC OS X drivers.................................................................................................. 33

PHASE 26 USB (English) 3

The PHASE ControlPanel (with Windows operating systems). ......................................35

OUTPUT.................................................................................................................35

MONITOR SETTINGS............................................................................................36

UPDATE.................................................................................................................38

MISC ......................................................................................................................39

Colors. ....................................................................................................................39

Practical tips and tools for the phono preamplifier. ........................................................41

Appendix A - Technical Data .........................................................................................45

Software .................................................................................................................45

Bundled software....................................................................................................45

PC System Requirements (not in ASIO mode) .......................................................46

MAC System Requirements (not in OS9 ASIO mode) ............................................46

System recommendations - PC ..............................................................................46

System recommendations - MAC ...........................................................................46

4 PHASE 26 USB (English)

Safety note.

Please ensure that analog audio connections are turned off before

plugging them in. This will protect you from any possible - albeit

weak - electrical shocks, as well as protecting your speakers and

your hearing from sudden peaks.

For digital devices, be sure to at least reduce the volume of your

playback equipment.

Static noise can also occur if you connect the device to the USB

port on your computer. Be sure to lower the volume on your play-

back system accordingly.

Welcome!

We are pleased that you have chosen a TerraTec Producer Audio Interface for your

musical endeavors and would like to congratulate you on your decision. With the

PHASE 26 USB Audio System, you've purchased a sophisticated product representing

the state of the art of studio technology - and we're convinced this innovative develop-

ment will prove extremely useful to you in the coming years and, above all, provide you

with a great deal of entertainment.

We hope that this brochure is helpful to you while using the product. It is designed to

illustrate technical relationships based on practical examples from the studio environment.

However, it is designed not only for beginners, but also for those more advanced in this

complex matter: Ambitious professionals, too, will surely learn something new here and

there.

We hope you find this manual both informative and entertaining to read, and hope you

find lots of pleasure in the PHASE 26 USB System.

Sincerely,Your TerraTec Producer Team

Your new audio interface: PHASE 26 USB.

PHASE 26 USB (English) 5

The widest variety of connecting equipment. The PHASE 26 USB System is designed

with a great variety of connecting options to ensure that you can connect it to your Mac,

PC or notebook, and thus turn it into the central audio station of your home and project

studio.

With three switchable stereo inputs (for example for your line device or LP record player),

eight line outputs (up to six can be used simultaneously), a MIDI interface and digital I/Os

for a variety of uses, the stable break-out box of the PHASE 26 USB System offers

sufficient connections in all directions. Selected transformer modules as well as a

thoroughly thought-out circuit board design make the quality of your recordings crystal

clear, and provide perfect playback capabilities for high-quality audio productions with

audio resolutions of up to 24-bit/96kHz.

►For everything you need to know about connections, see Üpage 20.

Nerve center - the software. As you know, a professional audio system is no sound card

for wild-eyed gamers, but the heart of your day-to-day studio work with your PC & MAC.

And despite the extensive routing options, the PHASE software always provides you with

a clear overview and- depending on the complexity of your switching needs- remains

transparent and intuitive.

►For everything you need to know about the PHASE-ASIO ControlPanel, see Üpage

35.

The drivers provided for the PHASE 26 USB System, too, leave nothing to be desired.

A highly developed software architecture guarantees problem-free use with all modern

Windows and Apple operating systems.

The ASIO drivers, tried and tested in studios, allow the lowest possible latency between

the software-based sound generation and audio output.

►For the details on driver use, please turn to Üpage 26.

6 PHASE 26 USB (English)

From unpacking the PHASE 26 to installing it.

Before connecting the PHASE 26 USB System to your computer, please take note of any

special points pertaining to the configuration of your computer. Also refer to the manual of

your computer and other studio peripheral devices for their settings.

The installation should be trouble-free, especially on modern-equipped systems. If you

still have difficulties, please review carefully the relevant chapter in this manual. If you are

still having problems, please call our service hotline. The phone numbers and hours of the

hotline can be found in the Appendix of this documentation.

Scope of delivery.

Start by making sure that the contents of the package are complete.

The PHASE 26 USB System package should contain the following items:

■

1 5¼" BreakOut module (the PHASE 26 USB hardware)

1 USB connector cable

2 adapter plugs, 6.3 mm stereo jack to 3.5 mm stereo socket

1 cinch adapter for grounding an LP turntable

1 installation and driver CD with software for Mac and PC

1 customer service card

1 registration card with the serial number

1 Besonic “Premium Account” card.

this manual

Please return the enclosed registration card to us at the earliest possible opportunity, or

and hotline services.

The operating modes.

Before you install the PHASE 26 USB System, we want to tell you about one of its

particular features, which makes it different from “conventional” audio devices (such as

PCI cards and on-board sound cards).

The data bandwidth of the USB 1.1 (Universal Serial Bus) is limited to a maximum of 1.5

Mbytes/sec. To take best advantage of the bus system, the PHASE 26 USB System

offers numerous methods of calling up various operating modes using the switches on the

front of the device.

Therefore, please note: Each configuration you select makes the device appear as

a new hardware device to your computer. Practically speaking, every time you

change the configuration, the device appears to be “disconnected” from the computer,

reconfigured and then reregistered on the computer. When the PHASE 26 USB System

PHASE 26 USB (English) 7

registers on the system, it informs the operating system of its specific properties for the

mode in which it is operating. The operating system then configures the hardware

accordingly and prompts for the drivers necessary for the new installation. In other words,

modes 1 to 4 plus the ASIO mode appear as 5 different physical devices to the operating

system, where each mode requires its own separate drivers to be installed.

The individual operating modes.

Depending on how you want to use the PHASE 26, change the operating mode using the

switches on its front panel. The individual modes available to you are:

Mode Audio inputs Audio outputs Max. resolution

1 1+2 - 24/96

2 - 1+2 24/96

3 1+2 1+2 24/48

4 1+2 1-6 16/48

If ASIO is enabled on the system, the four operating modes can be switched likewise. As

such, the module is then set up in all common audio applications as an ASIO device with

very low latency and the best possible sound quality. For “non-ASIO” audio applications,

however, you will have to do without the ASIO modes.

Note: As long as a software application is accessing a PHASE 26

USB driver, the device modes are locked and cannot be switched.

The PHASE 26 USB ControlPanel, too, blocks the device from

being switched and has to be closed in order to switch modes.

The input switch does not have any effect on driver selection. This is described further on

in section “Analog inputs.”, Üpage 22.

8 PHASE 26 USB (English)

Windows installation - step by step.

Be sure to follow these instructions carefully and in the order

in which they are described. First connect the PHASE 26 USB

module to the computer at the installation point indicated.

Do you know what the operating modes are?

Before you start installing the module, please read the previous chapter to learn about the

various operating modes on Üpage 7. Oh, but of course! Being the attentive person you

are, you've already read that chapter. ;-) (But really, read the previous chapter no matter

how excited you are to install your new device: the information it provides is extremely

important.)

Which operating system?

The PHASE 26 USB System is compatible with Windows 2000 and Windows XP (Home

Edition and Professional Edition). Older Windows versions are not officially supported.

Generally, the system should operate correctly under Windows 98SE and Windows ME.

However, not all of the device's functions may be available in this case (for example, MIDI

in ASIO mode is not always available for 98SE). Check that your installation of Windows

has been updated with the latest Microsoft service packs and updates. Otherwise (and

especially with Windows versions prior to Windows 2000), problems may occur with the

installation and operation of USB devices. We recommend the use of Windows XP -

practically all common audio applications provide full support for this operating system.

Installing the PHASE 26 USB ControlPanel and Driver.

When you place the provided product CD into the CD-ROM drive of your computer, the

autorun software should launch automatically. If the autorun application on the CD does

not launch automatically, start the application manually by double-clicking the “auto-

run.exe” file in the root directory of the CD. Simply follow the installation instructions for

the PHASE 26 USB ControlPanel. The “PHASE 26 USB Driver” button in the autorun

installation program copies the PHASE 26 USB driver (without ASIO) to your hard drive. If

you prefer, type in the name of the directory to which you want the driver installed. If later

you are prompted for a driver, simply indicate this directory.

PHASE 26 USB (English) 9

Power supply.

The PHASE 26 USB System generally can be operated from the USB port without the

need for a power adapter. You should ensure, however, that the port you wish to use can

provide the maximal USB 1 power of 500 mA. Normally, all computer USB interfaces and

hubs that provide their own power provide 500 mA. If necessary, check the technical

specifications of your computer or hub to make sure. Hubs that are themselves supplied

with power by the bus cable provide a maximum of 100 mA per port, and therefore are

not suitable for supplying power to the PHASE 26 USB System (such as, for example, the

USB port on a Macintosh keyboard). In this case, you can use a common 9-Volt DC

power adapter that can supply a direct current of 300 mA to power the PHASE 26 USB

System (to be purchased separately). You may want to use an external power adapter

anyway, for example to save your laptop battery.

Plug in the USB cable.

Now connect the PHASE module to the USB port on of your computer and wait a few

seconds.

Windows now detects, one after the other, the following new hardware components and

launches software wizards to install their drivers.

10 PHASE 26 USB (English)

Installing the PHASE 26 USB Driver for Windows 2000.

Important note: If the driver installation does not begin automati-

cally, you will have to update your firmware version. For more

information, please read section “Updating the firmware (Win-

dows).” on Üpage 16.

1. Make sure the ASIO mode is disabled on the device.

2. The “Found New Hardware Wizard” asks you to specify the location of the drivers for

the new hardware component “TerraTec PHASE 26 USB”. Select the “Search for a

suitable driver for my device” option. Confirm by clicking “Next”.

3. Enable the “Specify a Location” option and then click “Next”. In the next dialog, enter

the path to the driver folder as <CD>:\Driver\Windows\PHASE26USB\ or the path to

your hard drive (usually C:\TerraTec\PHASE 26 USB\) and confirm with “OK”. Confirm

the path in the Windows Wizard by clicking “Next”.

4. The following dialog box may appear at this point or later in the installation:

This is no cause for alarm. Click “Yes” to continue. The installation will now be exe-

cuted.

If contrary to all expectations an additional request should appear for you to perform

some action and you are not sure about it, then pressing the Enter key is generally a safe

action. If Windows requests a second driver file, please refer to the aforementioned

directory on the PHASE CD-ROM or on your hard disk.

PHASE 26 USB (English) 11

After a successful driver installation, you should verify the correct condition of your

Windows 2000 system. The Device Manager presents an overview of installed and

recognized hardware components of your computer. The Device Manager can be found

on the Control Panel under “System” > “Hardware”. Then click the “Device Manager”

button.

12 PHASE 26 USB (English)

Installing the PHASE 26 USB Driver for Windows XP.

Important note: If the driver installation does not begin automati-

cally, you will have to update your firmware version. For more

information, please read section “Updating the firmware (Win-

dows).” on Üpage 16.

1. Make sure the ASIO mode is disabled on the device.

2. The “Found New Hardware Wizard” asks you to specify the location of the drivers for

the new hardware component “TerraTec PHASE 26 USB”. Select “Install from a list or

specific location...”. Confirm by clicking “Next”.

3. Enable the “Search for the best driver in these locations” and “Include this location in

the search” options. In the next dialog, enter the path to the driver folder as

<CD>:\Driver\Windows\PHASE26USB\ or the path to your hard drive (usually

C:\TerraTec\PHASE 26 USB\) and confirm with “OK”. Confirm the path in the Win-

dows Wizard by clicking “Next”.

4. The following dialog box may appear at this point or later in the installation:

This is no cause for alarm. Click “Continue Anyway” to continue. The installation will

now be executed.

5. In the final window, the hardware wizard will report that the driver software has been

installed successfully. Close the wizard by clicking “Finish”.

If contrary to all expectations an additional request should appear for you to perform

some action and you are not sure about it, then pressing the Enter key is generally a safe

action. If Windows requests a second driver file, please refer to the aforementioned

directory on the PHASE CD-ROM or on your hard disk.

PHASE 26 USB (English) 13

After a successful driver installation, you should verify the correct condition of your

Windows XP system. The Device Manager presents an overview of installed and

recognized hardware components of your computer. The Device Manager can be found

on the Control Panel under “System” > “Hardware”. Then click the “Device Manager”

button.

Switching operating modes.

As mentioned already, the PHASE 26 USB module registers with the operating system as

new hardware when the operating mode is switched. Because of this, we recommend that

you switch once through all of the modes right now. Remember that you can not switch

modes unless all of the programs that access the PHASE 26 USB drivers are closed

(including the PHASE 26 USB ControlPanel). Every time you switch from one mode to

another, the installation procedure repeats the steps listed above. While time-consuming

now, this will avoid the surprise (which would of course happen at the least appropriate

time) of having to install the drivers in the future. Authors remarks: Yes, I agree. This

procedure may not seem worthwhile, and can be frustrating. And things get better: If you

switch the USB port you are using, Microsoft's Windows detects all of the “devices” as

new. Unfortunately, there is nothing the TerraTec production team can do about this - so,

bear it with a grin! Everything will be just fine!

Installing the ASIO driver.

1. Disconnect the USB connection between the PHASE 26 USB System and your

computer.

2. Use the autorun software on the PHASE 26 USB product CD to launch the installation

of the ASIO driver.

3. Follow the installer software instructions in the screen.

If the ASIO mode will be changed for the first time at the device it might happen the

Windows hardware wizard pops up again. In this case simply choose the hardware

wizards automatic installation.

Congratulations!

Your PHASE 26 USB System is now available for use as an audio device in all applica-

tions. To better understand the interaction of the PHASE 26 USB System with Windows,

we recommend reading the descriptions in the driver chapter on Üpage 26.

14 PHASE 26 USB (English)

Driver installed (ASIO mode disabled)

Driver installed (ASIO mode enabled)

PHASE 26 USB (English) 15

The PHASE 26 USB as a system audio device (Windows).

If you want to use the PHASE 26 USB System not only in your audio applications, but

also as the preferred audio device for Windows, simply open the Windows Control Panel,

go to “Sounds and Multimedia” > “Audio”, and select the PHASE 26 audio driver as the

“Preferred Device” for any or all system audio functions.

Then you can use the standard speaker icon in the Windows taskbar to adjust volume.

For details on the mixer functions for your Windows operating system version, refer to the

Microsoft Windows help on your system. You can also use the PHASE 26 USB Control-

Panel to adjust the output volume.

Updating the firmware (Windows).

Thanks to the advanced software technology: Future changes to existing standards and

new functions developed for the PHASE 26 USB System can be integrated simply by

updating the device's “firmware”, without having to replace or change any hardware. To

update the firmware, follow these steps:

■

First unplug the USB connection from the PHASE 26 USB hardware. Now press the

“Mode” and “Input” buttons on the PHASE 26 USB module at the same time while you

plug the USB cable back in.

The hardware now registers as a “PHASE 26 Firmware Update” device and, if this is

the first time you've updated the firmware, the Windows hardware wizard opens to

install the update drivers.

Select “Install from a list or specific location” and enter the path to the drivers in the

next dialog, for example on the product CD

<CD>:\PHASE 26 USB\Driver\PC\PHASE 26 USB Driver\ (or as an update

from the TerraTec web site).

After the “Flash Updater for TerraTec PHASE 26 USB” driver has been installed

successfully (which you can confirm in the Device Manager -> USB Controllers),

launch the PHASE 26 USB ControlPanel. If you have not yet installed the Control-

Panel, run the installer from the autorun program on the PHASE CD.

Click the “Load” button on the Update page of the ControlPanel. Browse to and select

the current Windows firmware called “PHASE26USB_WIN_x.xx.BIN”, for example on

the CD: <CD>:\PHASE 26 USB\Driver\PC\Firmware\ or as an update from the

TerraTec web site.

Click “Open” to close the browse dialog and begin the firmware update automatically.

You can view the progress of the update in the status window.

When done, unplug the USB cable again and then plug it back in a few seconds later.

The PHASE 26 USB System is again available for your use.

16 PHASE 26 USB (English)

MAC installation - step by step.

Be sure to follow these instructions carefully and in the order in

which they are described. First connect the PHASE 26 USB

module to the computer at the installation point indicated.

Do you know what the operating modes are?

Before you start installing the PHASE 26 USB System, please read the previous chapter

to learn about the various operating modes of the PHASE 26 USB System on Üpage 7.

Oh, but of course! Being the attentive person you are, you've already read that chapter.

;-) (But really, read the previous chapter no matter how excited you are to install your new

device: the information it provides is extremely important.)

Which operating system?

The PHASE 26 USB System can be used with MAC OS 9.x and MAX OS 10.x (OS X). A

special ASIO driver is available for OS 9, but there is no MIDI driver. Furthermore, the

OS 9 Sound Manager is not supported. Implementing the PHASE 26 USB System in

OS X is easy with the help of OS X CoreAudio and CoreMIDI. We recommend purchas-

ing and installing the MAC OS X “Jaguar” upgrade, as it includes several improvements in

detail, including some for audio applications.

Driver installation.

Installing the ASIO under OS9.

Copy the compressed .SIT file from the installation CD

(<CD>:\PHASE 26 USB\Driver\Mac\OS9\ASIO\) to the MAC OS9 Desktop and then

extract it using an application such as StuffIt-Expander. Now copy the

”PGTerraTecPhase26” file from the extracted folder to the system extensions folder.

Then copy the ASIO driver, called “TerraTec Phase 26 ASIO Driver”, to the ASIO folder of

your audio application and reboot the computer.

Installation under OS X.

As mentioned above, the PHASE 26 USB System implements the operating system's

own CoreAudio and CoreMIDI drivers. Because of this, there is no need to install other

drivers. Once you've plugged the module into the MAC USB port, it is immediately

available for your use.

PHASE 26 USB (English) 17