Tesco TF37 User manual
PLACEMENT
SWITCHING ON
OPERATION
OSCILLATION
CARRYING THE FAN
CARE AND MAINTENANCE
WARRANTY
A
fter assembly, stand the fan upright on a solid
level floor in a safe location.
The control panel of the fan consists of a Speed
Switch, a Timer Control and an Oscillator Button.
switches the fan off.
selects Low speed
selects Medium speed
selects High Speed
The setting disables the timer. In this mode
the fan is controlled by the Speed buttons.
The timer can be set from 0 to 120 minutes.
When the time is up, the timer reaches 0 and
switches the fan off.
To operate the fan again:
Set the Timer to ON or set a new time.
Ensure the Speed Switch is set to‘0’.
Set the TIMER to ON, or select a time.
Plug in the fan and switch it on at the mains.
Now select the desired speed.
Your fan can oscillate about its axis for better
cooling. The oscillator button is located under the
Timer Knob and marked with the symbol .
Ensure that the fan can oscillate freely before using
this feature.
To oscillate the fan press the oscillator button in.
Press and release the Oscillator button again
to return to fixed operation..
Press the oscillator button down, allow the fan
to reach the desired position and press the
oscillator button again to lock the fan in its
new position.
When moving the fan always ensure that it is
switched off and unplugged at the mains point.
Carry the fan with one hand in the handgrip at the
top rear and the column body in the other.
Before cleaning, switch the fan off and unplug
from the mains. The fan column may be cleaned
with a mild detergent lightly applied to a damp
cloth. Remove all traces of detergent with a clean
damp cloth and dry thoroughly before operating
the appliance.
Never spray liquid onto any part of the fan or allow
liquids to run into the interior of the appliance.
When not in use, store the appliance away from
sources of moisture and heat and where children
and pets cannot access the unit.
Your Tesco appliance is covered by a warranty for
12 months from the date of purchase. If a fault
develops during this period, please return it
together with your original purchase receipt to
your nearest Tesco store. This warranty in no way
affects your consumer rights.
The Speed Switch
0
1
2
3
The Timer
ON
!
!
!
!
!
!
!
!
!
!
!
!
!
!
When the timer registers 0 you cannot switch
the fan on or off via the speed switch
To change the angle at which the fan operates:
Tesco Stores Ltd
,
Delamare Road
,
Cheshunt
,
Herts
,
EN8 9SL
Timer
Knob Oscillator
Button
Speed Control Buttons
CONTROL PANEL
TF37 Tower Fan User Guide
Produced after 13th August 2005.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
TF37
To w e r F a n
User Guide
IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL INFORMATION
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Read these instructions.
Keep these instructions.
Follow all instructions.
Unplug the fan when not in use, before moving it
between locations and before cleaning,
Refer all servicing to qualified service personnel.
Do not expose this apparatus to rain or
moisture, e.g. by operating it in a window or
verandah, etc.
Do not immerse the power cord or plug in water.
Do not spray liquids into or near the fan
Do not operate this unit in the presence of
explosive and/or flammable fumes.
Do not place the fan on or near an open flame,
cooking or heating appliance.
Avoid contact with moving parts.
Protect the power cord from being walked on or
pinched.
The power cord must not present a source of
danger to persons or pets.
Do not operate the fan with a damaged cord or
plug, after a malfunction or if dropped or
damaged in any way.
To disconnect, grip the plug and pull from wall
outlet. Never yank on the power cord.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid hazard.
The use of attachments not recommended by
the manufacturer may be hazardous.
Warning: Do NOT use this fan with any solid
state voltage regulator or speed control.
Always use on a dry, level and stable surface
when operating to avoid overturning.
Do not mount this fan on a table or elevated
stand.
Do not hang or mount the fan on a wall or
ceiling.
Never use the fan improperly assembled or
without the guard correctly fitted.
Do not insert any object into the fan whether the
fan is running or not.
Close supervision is necessary when any
appliance is used by or near children.
This product is intended solely for household use
Before using this appliance ensure that the voltage
of your electricity supply is the same as that indicated
on the appliance.
The means of disconnecting this appliance from the
mains supply is the mains plug. This should be
unobstructed and readily operable at all times .
The appliance cord is terminated with a UK
approved mains plug fitted with a 3A fuse. If
Class II construction double insulated. This
product must not be connected to earth.
the fuse
needs to be replaced, an ASTA or BSI approved
BS1362 fuse rated at 3A must be used.
If you need to change the fuse in a non-rewireable
plug, the fuse cover must be fitted. If the fuse cover is
lost or damaged the appliance must not be used
until a suitable cover is obtained and fitted. It is
important that the fuse cover fitted corresponds with
the colour marking on the base of the plug.
If you need to change the mains plug, remove the
fuse and dispose of the old plug safely immediately
after cutting it from the cord.
The wires in the mains lead are coloured in
accordance with the code:
NEUTRAL, LIVE
As these colours may not correspond to the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire coloured
BLUE must be
connected to the
terminal marked
with the letter N or
coloured BLUE or
BLACK.
The wire coloured BROWN must be connected
to the terminal marked with the letter L or
coloured BROWN or RED.
Do NOT connect to the terminal marked with
the letter E or coloured GREEN or GREEN &
YELLOW or marked with the Earth Symbol .
Model No. TF37
Mains Voltage 220V-240V AC, 50 Hz
Mains Power Watts
Connecting a Mains Plug
Blue: Brown:
$
$
$
SPECIFICATIONS
60
3A FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
TF37 Tower Fan User Guide
INTRODUCTION
UNPACKING
ASSEMBLY
Before using this appliance please read all these
notes and instructions carefully and famliarise
yourself with the features of your new appliance. In
particular, please study the assembly instructions
before assembling your tower fan.
Unpack all the items carefully and remove all plastic
wrappings from the component parts.
Check the fan carefully. If any items are damaged or
missing, please return the appliance for
replacement to the store you purchased it from, or to
your nearest Tesco store. Remember to take your
receipt.
Retain the packing, or if you decide to dispose of it,
make sure that you do so with due regard to any
recycling provisions currently in force.
For ease of assembly, lay the Fan down so that
the front grill and control panel are facing up.
Identify the two base sections and .
Remove the four screws attached to the support
pillars in Section A and keep them safe
Thread the Power Cord through the centre of the
support base section A.
Align the two Base sections by interlocking the
guides on Base A with the support pillars on Base B.
Push them firmly together.
Attach the four screws screws into the four
holes in the pillars at the bottom of the base.
Note the position of the power cord.
Remove the four screws in the base of the
fan column and save them
Align the support base assembly with the
column support assembly
Ensure that the cord channel on the bottom of
the support base faces the rear of the fan.
Ensure that the power cord is routed away from
the oscillating mechanism at the base of the
fan so that the cord is not damaged and does
not prevent the fan from oscillating.
Attach the support base assembly to the
column support assembly with the four screws.
Place the cord in the wire trough in the base.
The power cord is protected by a length of
plastic sleeve. Push the cord under the strain
relief in the back of the base. The sleeve should
protrude just beyond the fan support base.
1.
AB
2.
3.
4.
5.
6.
7.
.
8.
(refer to Fig 1 below)
(Figure 2)
Fig. 1
Power Cord
Base
Section A
Support
Pillars
Fig. 2
Screws
Base
Section B
Assembled Base
Power
Cord
Power
Cord
Trough
& Strain
Relief
Clip
Base
Fig. 3
Screws
TF37 Tower Fan User Guide
IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL INFORMATION
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Read these instructions.
Keep these instructions.
Follow all instructions.
Unplug the fan when not in use, before moving it
between locations and before cleaning,
Refer all servicing to qualified service personnel.
Do not expose this apparatus to rain or
moisture, e.g. by operating it in a window or
verandah, etc.
Do not immerse the power cord or plug in water.
Do not spray liquids into or near the fan
Do not operate this unit in the presence of
explosive and/or flammable fumes.
Do not place the fan on or near an open flame,
cooking or heating appliance.
Avoid contact with moving parts.
Protect the power cord from being walked on or
pinched.
The power cord must not present a source of
danger to persons or pets.
Do not operate the fan with a damaged cord or
plug, after a malfunction or if dropped or
damaged in any way.
To disconnect, grip the plug and pull from wall
outlet. Never yank on the power cord.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid hazard.
The use of attachments not recommended by
the manufacturer may be hazardous.
Warning: Do NOT use this fan with any solid
state voltage regulator or speed control.
Always use on a dry, level and stable surface
when operating to avoid overturning.
Do not mount this fan on a table or elevated
stand.
Do not hang or mount the fan on a wall or
ceiling.
Never use the fan improperly assembled or
without the guard correctly fitted.
Do not insert any object into the fan whether the
fan is running or not.
Close supervision is necessary when any
appliance is used by or near children.
This product is intended solely for household use
Before using this appliance ensure that the voltage
of your electricity supply is the same as that indicated
on the appliance.
The means of disconnecting this appliance from the
mains supply is the mains plug. This should be
unobstructed and readily operable at all times .
The appliance cord is terminated with a UK
approved mains plug fitted with a 3A fuse. If
Class II construction double insulated. This
product must not be connected to earth.
the fuse
needs to be replaced, an ASTA or BSI approved
BS1362 fuse rated at 3A must be used.
If you need to change the fuse in a non-rewireable
plug, the fuse cover must be fitted. If the fuse cover is
lost or damaged the appliance must not be used
until a suitable cover is obtained and fitted. It is
important that the fuse cover fitted corresponds with
the colour marking on the base of the plug.
If you need to change the mains plug, remove the
fuse and dispose of the old plug safely immediately
after cutting it from the cord.
The wires in the mains lead are coloured in
accordance with the code:
NEUTRAL, LIVE
As these colours may not correspond to the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire coloured
BLUE must be
connected to the
terminal marked
with the letter N or
coloured BLUE or
BLACK.
The wire coloured BROWN must be connected
to the terminal marked with the letter L or
coloured BROWN or RED.
Do NOT connect to the terminal marked with
the letter E or coloured GREEN or GREEN &
YELLOW or marked with the Earth Symbol .
Model No. TF37
Mains Voltage 220V-240V AC, 50 Hz
Mains Power Watts
Connecting a Mains Plug
Blue: Brown:
$
$
$
SPECIFICATIONS
60
3A FUSE
BS 1362
BROWN
(Live)
BLUE
(Neutral)
TF37 Tower Fan User Guide
INTRODUCTION
UNPACKING
ASSEMBLY
Before using this appliance please read all these
notes and instructions carefully and famliarise
yourself with the features of your new appliance. In
particular, please study the assembly instructions
before assembling your tower fan.
Unpack all the items carefully and remove all plastic
wrappings from the component parts.
Check the fan carefully. If any items are damaged or
missing, please return the appliance for
replacement to the store you purchased it from, or to
your nearest Tesco store. Remember to take your
receipt.
Retain the packing, or if you decide to dispose of it,
make sure that you do so with due regard to any
recycling provisions currently in force.
For ease of assembly, lay the Fan down so that
the front grill and control panel are facing up.
Identify the two base sections and .
Remove the four screws attached to the support
pillars in Section A and keep them safe
Thread the Power Cord through the centre of the
support base section A.
Align the two Base sections by interlocking the
guides on Base A with the support pillars on Base B.
Push them firmly together.
Attach the four screws screws into the four
holes in the pillars at the bottom of the base.
Note the position of the power cord.
Remove the four screws in the base of the
fan column and save them
Align the support base assembly with the
column support assembly
Ensure that the cord channel on the bottom of
the support base faces the rear of the fan.
Ensure that the power cord is routed away from
the oscillating mechanism at the base of the
fan so that the cord is not damaged and does
not prevent the fan from oscillating.
Attach the support base assembly to the
column support assembly with the four screws.
Place the cord in the wire trough in the base.
The power cord is protected by a length of
plastic sleeve. Push the cord under the strain
relief in the back of the base. The sleeve should
protrude just beyond the fan support base.
1.
AB
2.
3.
4.
5.
6.
7.
.
8.
(refer to Fig 1 below)
(Figure 2)
Fig. 1
Power Cord
Base
Section A
Support
Pillars
Fig. 2
Screws
Base
Section B
Assembled Base
Power
Cord
Power
Cord
Trough
& Strain
Relief
Clip
Base
Fig. 3
Screws
TF37 Tower Fan User Guide
PLACEMENT
SWITCHING ON
OPERATION
OSCILLATION
CARRYING THE FAN
CARE AND MAINTENANCE
WARRANTY
A
fter assembly, stand the fan upright on a solid
level floor in a safe location.
The control panel of the fan consists of a Speed
Switch, a Timer Control and an Oscillator Button.
switches the fan off.
selects Low speed
selects Medium speed
selects High Speed
The setting disables the timer. In this mode
the fan is controlled by the Speed buttons.
The timer can be set from 0 to 120 minutes.
When the time is up, the timer reaches 0 and
switches the fan off.
To operate the fan again:
Set the Timer to ON or set a new time.
Ensure the Speed Switch is set to‘0’.
Set the TIMER to ON, or select a time.
Plug in the fan and switch it on at the mains.
Now select the desired speed.
Your fan can oscillate about its axis for better
cooling. The oscillator button is located under the
Timer Knob and marked with the symbol .
Ensure that the fan can oscillate freely before using
this feature.
To oscillate the fan press the oscillator button in.
Press and release the Oscillator button again
to return to fixed operation..
Press the oscillator button down, allow the fan
to reach the desired position and press the
oscillator button again to lock the fan in its
new position.
When moving the fan always ensure that it is
switched off and unplugged at the mains point.
Carry the fan with one hand in the handgrip at the
top rear and the column body in the other.
Before cleaning, switch the fan off and unplug
from the mains. The fan column may be cleaned
with a mild detergent lightly applied to a damp
cloth. Remove all traces of detergent with a clean
damp cloth and dry thoroughly before operating
the appliance.
Never spray liquid onto any part of the fan or allow
liquids to run into the interior of the appliance.
When not in use, store the appliance away from
sources of moisture and heat and where children
and pets cannot access the unit.
Your Tesco appliance is covered by a warranty for
12 months from the date of purchase. If a fault
develops during this period, please return it
together with your original purchase receipt to
your nearest Tesco store. This warranty in no way
affects your consumer rights.
The Speed Switch
0
1
2
3
The Timer
ON
!
!
!
!
!
!
!
!
!
!
!
!
!
!
When the timer registers 0 you cannot switch
the fan on or off via the speed switch
To change the angle at which the fan operates:
Tesco Stores Ltd
,
Delamare Road
,
Cheshunt
,
Herts
,
EN8 9SL
Timer
Knob Oscillator
Button
Speed Control Buttons
CONTROL PANEL
TF37 Tower Fan User Guide
Produced after 13th August 2005.
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice.
TF37
To w e r F a n
User Guide
Other manuals for TF37
1
Table of contents
Other Tesco Fan manuals
