Tesco Mika Shorty Bunk User manual

Version 1
Before You Start
•Important: Retain these instructions for future reference.
•When you are ready to start, make sure that you have the right tools, plenty of space and a
clean, dry area for assembly.
•Unwrap all packaging materials and place the components on top of the carton box or on a
clean floor to prevent it from scratching.
•Check the pack and make sure you have all the parts listed.
•During assembly children should be kept away from the product due to possible risk of injury.
•Tools not included.
•Do not use power tools to construct this product.
•Due to the size of this product we recommend that it is assembled in the room intended for
use.
•Ensure that this product is fully assembled as illustrated before use.
Warnings
•This product is intended for a maximum weight of 100 kg. Do not exceed this weight.
•It is recommended that 2 people are required to assemble this product.
•This product should only be used on firm, level ground.
•Make sure the legs remain in contact with the ground.
•Keep small parts out of reach of children.
•Check all screws or bolts are tightened and inspect regularly.
•Do not tighten screws until fully assembled.
•Do not over tighten screws or bolts.
•Do not use this product if parts are missing, damaged or worn.
•Do not allow children to jump on the bed as this could cause damage to the frame.
•This product complies with the requirements of UK Bunk Beds Entrapments Hazards Safety
Regulations 1987 and the European Standard EN 747-1 & 2 ：2007
•Top bunk not recommended for children under the age of 6 years. Be aware of the danger of
young children (under 6) falling from the upper bunk.
•The top of the mattress must not come above the line marked on the bed.
Care Instructions
•To clean wipe with a sponge and warm soapy water. Do not use solvent based cleaners or
detergents as they can bleach or damage the product.
Mika Shorty Bunk
(
75x175cm
)

Version 1
x 4 PCS(Metal post) x 2 PCS x 2 PCS
(Ladder)
x2PCS(SideRail)
Parts List:
(Headboard /Footboard)
x 1 PC(Long safety rail)
x 3 PCS (Ladder steps)
x 4 PCS (Metal slat joint)
x 2 PCS (Metal slat)
x1PC(Short safetyrail) (Headboard / Footboard)
(Bottompanel)
x 2 PCS

Version 1
1
2K
1
D
1
D
O
10
D
D
O
10
2
6
6
8
7
6
D
7
DL
L
8
K
K
D
D
Fitting List:-
D16
M6 X 20MM
K1
O4
M4
38MM
Fitting List:-
D8
M6 X 20MM
K1
L4
M4
25 X 50 MM

Version 1
3
7
G
Twist left
and right
Using a plier or your finger, adjust the
wire into the correct position shown
in picture A,
Twist left and right until the wire comes through
the hole, then adjust the wire to the correct
position shown in picture B.
During assembly, if the pin does not come out,
please follow the steps below to adjust,
PICTURE A PICTURE B
Fixing G is used to press down the wire to insert
part 5 into part 7 & 8 then release. Remove Fixing
G from part 5 and then repeat this all parts 5's
are fitted.
4
D
6
6
3
3D
K
K
K
turn over
L
L
5
D
Fitting List:-
G1
Fitting List:-
D8
M6 X 20MM
K1
L4
M4
25 X 50 MM

Version 1
5
3
Twist left
and right
Using a plier or your finger, adjust the
wire into the correct position shown
in picture A,
Twist left and right until the wire comes through
the hole, then adjust the wire to the correct
position shown in picture B.
During assembly, if the pin does not come out,
please follow the steps below to adjust,
PICTURE A PICTURE B
G
Fixing G is used to press down the wire to insert
part 5 into part 3, then release. Remove Fixing
G from part 5 and then repeat this all parts 5's
are fitted.
6
EA
E
A
E
B
B
A
7K
B
E
J
A
A
7
5Fitting List:-
G1
Fitting List:-
A4
M8 X 80MM
E4
B3
J1
M5
M6 X 60MM
M4
K1
K
J