Tesco FS10 User manual

FS10 USER GUIDE
$Release the ON/OFF button and allow the machine to
OPERATION
stop before making adjustments or removing the food
after you have finished slicing.
$Always keep your fingers well clear of the blade. Use the
slice feed plate whenever possible.
$If it is impossible to use the slice
feed plate you can remove the
plate and hand feed the food to
the slicer. Extreme caution must
be taken if you do this. To avoid
accidents the unsliced portion
must never be permitted to go
below the depth of the Sliding
OPERATION table guard.
$Assemble the machine and place the Collecting Tray at $
the front of the machine. Refer to View A on Page 3.
$Adjust the slice thickness as required $
$Plug the appliance into the mains. Switch the mains on.
$Move the Sliding table back so that the front edge of the
food is clear of the slicing blade.
$Place the food so that it is supported by the guard and
the slice feed plate.
$Press the Safety switch in and then press the ON/OFF
switch to start the slicer. You may now release the safety
switch if you wish.
Slice Feed Plate from the Sliding Table
Remove the Sliding Table.
Move the table
slowly back and
forth and lift it
slightly.
When the table
lines up with the
slot in the baseplate
it will lift up, and
you can remove it
$Keeping the ON/OFF switched pressed, bring the Slice easily.
Feed plate against the food and gently press the food DO NOT use force.
against the slicing plate. Move the food across the blade
forward and back. Collect the slices in the collecting tray.
Adjusting Slice Thickness
Tur n the Th ickness control
Clockwise to increase and
Anticlockwise to decrease the slice
thickness. The Thickness indicator
indicates the slice thickness.
When the control is rotated the Slice
Feed Plate moves in and out. For
safety, always rotate the control
anticlockwise to move the Slice Feed plate in front of the Knife
blade so that it is covered when the unit is not in use.
If the motor slows or the blade gets hot, switch off, and
allow the unit to cool fully before recommencing slicing.
Do not run the machine continuously for more than 6
min. Allow the unit to cool before recommencing slicing.
CARE AND CLEANING
After Use:
$Release the ON/OFF switch.
$Unplug the appliance and allow the machine to stop
rotating.
$Remove the sliced meat from the tray.
$Move the sliding plate back so any unsliced meat is well
clear of the slicing knife. Lift off any unsliced meat from
the machine.
Cleaning the machine and attachments
$Lift the
$
$Remove the slicing knife. (Refer to Fig. 3 on Page 4) MAINTENANCE
$Remove the Slicing Table. Turn the Thickness knob fully The feed screw of the slicing table is lightly greased. If it is
anticlockwise to release the table and lift it out. necessary to remove food residues from this area of the
appliance, clean the feed screw with a soft cloth dampened
with soapy water followed with a clean damp cloth and dry.
To re-grease the screw, apply a small dab of petroleum jelly
(Vaseline) to the screw and then replace the slicing table.
$Wash all the removed plastic components in warm
soapy water, rinse and dry thoroughly.
$Wash the slicing knife in warm soapy water taking care
not to touch the cutting surfaces, rinse and dry thoroughly.
$Wipe the motor unit, the base plate the rear plate and
all other surfaces, including the area behind the knife
blade all over with a soft cloth dampened with soapy
water followed with a clean damp cloth. Dry well. Do not
immerse the motor unit, mains cable or plug in water.
NOTE: This machine is used primarily to slice cooked or cured
meats which are not subjected to further cooking. It is essential
to keep this appliance spotlessly clean as there is a risk of
infection from cross-contamination due to infected food
residues if the unit is not thoroughly clean. When cleaning this
appliance, we strongly advise the use of anti-bacterial Class II construction double insulated. This product
cleaning agents (wipes, liquids or sprays) approved for use must not be connected to earth.
with food processing appliances. Follow the instructions on the
packaging of the anti-bacterial product carefully.
After Cleaning:
$Replace the Slicing Table. Reverse the instructions for
disassembly (Fig. 10 above)
$Replace the Slicing Knife. Make sure the slicing table is
extended so it is in front of the knife blade.
$Finally fold the appliance shut and replace the tray.
$Loosely coil the cable and store the unit with all
attachments in a dry cool cupboard out of the reach of
children and pets.
WARRANTY
Your appliance is covered by a warranty for 12 months from
the date of purchase. If a fault develops during this period,
please return the unit to your nearest Tesco store together
with the original receipt as proof of purchase. This warranty
in no way affects your consumer rights.
SPECIFICATIONS
Power: 230-240 VAC 50Hz, 120W
Duty Cycle: 6 minutes ON; 15 minutes OFF
Weight:
UK: Waste electrical products should not be
disposed of with household waste.
e for details.
ROI: Produced after 13th August 2005. Waste
electrical products should not be disposed of
with household waste. Please recycle where
facilities exist. Check with your Local Authority
or retailer for recycling advice.
1.2 kg
Separate
disposal facilities exist, for your nearest
facilities see www.recycle-more.co.uk or in-
stor
Page 5 Page 6
Tesco Stores Ltd, Delamare Road, Cheshunt, Herts, EN8 9SL
Food Slicer
USER GUIDE
FS10
FS10 USER GUIDE
MINIMUM
RESIDUAL
DEPTH
Fig 6
Fig 8
Fig 9
Fig 10
FEED SCREW
Fig 11
Fig 7

SAFETY GUIDE - PLEASE READ CAREFULLY mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
Please follow all the safety precautions listed below for safety instruction concerning use of the appliance by a person
and to reduce the risk of injury or electrical shock. responsible for their safety.
$Read all the instructions carefully before using your
$Children should be supervised to ensure that they do not
blender and keep them for future reference.
play with the appliance.
$Unplug the appliance from the mains supply when not
in use, when removing or attaching accessories, or When operating this appliance:
before cleaning any part of the appliance.
$When the appliance is not in use make sure that it is
$This appliance is for occasional household use only. safely unplugged from the mains supply.
$Do not use outdoors or in damp conditions. $To reduce the risk of injury, ensure that the cutting blade
$Do not immerse the motor unit or the electrical cord or is fully retracted when not in use.
plug in liquids. $When using the appliance ensure there is adequate
$Do not use near a source of heat or on an unstable room to work.
surface. $Do not run the appliance continuously for more than 6
$Ensure that the power cord does not touch any hot minutes After 6 minutes of continuous use let the unit
surface and that it does not overhang the edge of your cool for 15 minutes before using it again.
work surface. $The slicing knife on this appliance is sharp. Treat it with
$When unplugging the power cord, hold the plug top, not care at all times and never allow fingers, hair, or
the power cord. clothing to come into contact with the blade.
$Do not operate any appliance with a damaged cord or $
plug or after the appliance malfunctions, or is dropped
or damaged in any manner. Return the appliance to the $Do not slice hard or dense materials (such as hard
nearest authorised service facility for examination, cheeses) which cannot safely be sliced by the knife.
repair or electrical or mechanical adjustment.
$DO NOT slice food containing bones or frozen food.
$Do not use attachments or accessories which are not
$Very soft materials (i.e. Mozzarella Cheese)may tear, If
recommended by the manufacturer. They may cause there is any sign of tearing discontinue slicing the
malfunction or injury. material.
$Do not attempt to replace the power cord on this
$If the knife gets clogged, switch off, and allow the unit to
appliance. This should only be carried out by authorised stop before clearing the obstruction.
service personnel with specialist tools.
$If the motor slows down or the blade gets hot, switch off,
$Store the appliance away from direct sunlight and out of and allow the unit to stop and cool down before
the reach of children. recommencing slicing.
$There are no user serviceable parts in your appliance $Operate the appliance is on a sturdy work surface. and
Unauthorised dismantling or servicing will void the hold or support it during operation
product warranty.
$Do not yank or pull the cord as this may damage it and
$Do not use the appliance for any purpose not expressly eventually cause a risk of electric shock.
specified in this manual. $To protect against fire, do not operate the unit in the
$This appliance is not intended for use by persons presence of explosive and/or flammable fumes.
(including children) with reduced physical, sensory or $Keep the unit out of the reach of children
Hold the knife blade by the clamp when removing and
attaching it to the appliance.
COMPONENTS AND CONTROLS
Page 2 Page 3 Page 4
UNPACKING Before every use of your appliance:
$ Remove the Collecting Tray (2). (See Figure 1)
$Remove all packaging from the appliance. Retain the
$Wash the plastic components (12, 13, 14) and the tray (2)
packaging. If you dispose of it please do so according to
in warm soapy water , rinse and dry thoroughly.
any recycling regulations.
$Open the appliance and remove the slicing knife (7) (see
$Read and retain the manual. If you pass the product on
Fig.3) Wash in warm soapy water taking care not to touch
to a third party, make sure to include this manual.
the cutting surfaces, rinse and dry thoroughly.
PRELIMINARIES
$Wipe the motor unit (3), and the Tables(6, 10, 11) all
Always make sure the appliance is unplugged from the over with a soft cloth dampened with soapy water
mains when cleaning, attaching or removing accessories followed with a clean damp cloth. Dry well. Do not
Refer to the assembly instructions on the next page and the immerse the motor unit, mains cable or plug in water.
illustrations above. $Replace the Slicing Knife and assemble the unit for use.
PREPARATION FOR USE 2: Assemble the Sliding Table and Guard:
Hold the table down. Line the three tabs on the bottom of
the Guard with the slots in the top of the Sliding table and
push the Guard into place. make sure the Guard is firmly
locked to the table. Once assembled we do not recommend
dis-assembly of the table.
4: Attach the Sliding Table
1: Ensure the Slicing Knife edge is safely behind the Slice
adjustment table . (See Figure 6).
2: Line the tab under the Sliding
table with the slot in the Base Plate.
Insert the table into the slot and press
gently. Slide the table back and forth
and check it moves freely but securely
over the base plate. (See View B on Page 2).
FS10 USER GUIDEFS10 USER GUIDE
1: Thickness Adjustment Dial
2: Collecting Tray
3: Motor Housing
4: Safety Switch
5: Thickness Indicator
6: Slicing Table
7: Slicing Knife
8: Slicing Knife Clamp
9: On/Off Button
10: Rear Plate
11: Base Plate
12: Sliding Table
13: Slice Feed Plate
14: Sliding Table Guard
3
2
VIEW A
3: Removing and Replacing the Slicing Knife
Ensure the sliding table is removed.
A: Rotate the Clamp Clockwise
to unlock the Slicing Knife and
Anticlockwise to lock it.
B: Hold the knife blade by the
clamp when removing and
attaching it.
To attach the Slicing Knife, hold it as shown, place it into the
recess in the motor and rotate anticlockwise.
NEVER TOUCH THE BLADE EDGE WITH YOUR FINGERS!
UNLOCK
LOCK
Fig 3A
Fig 3B
Figure 2
FS10 USER GUIDE
1: Ensure the machine is disconnected from the mains.
Invert the unit. Place the unit on a solid level surface and
hold it securely. Detach the Collecting Tray.
Figure 1
Fig 4A
5: Attach the Slice Feed Plate
Place the Slice Feed Plate over the Sliding Table Guard as
shown.
Slide it back and forth and ensure it moves freely.
Fig 5BFig 5A
1
10
5 6 7 8
11
12
13
9
VIEW B
14
4