Tesla TGZUJ-V07P4 User manual

MULTI SPLIT-TYPE
AIR CONDITIONER
USER
MANUAL
For Indoor unit models:
TGZUJ-V07P4
TGZUJ-V09P4
TGZUJ-V12P4
TGZUJ-V18P4
TGZUJ-V24P4
Ver. 2022
ENG RO SLO SRB

OPERATING INSTRUCTION
Note: All the pictures in this manual are just schematic diagrams, the actual is the standard. Please read
this owner’s manual carefully and thoroughly before operating the unit! Take care of this manual for future
reference.
MANUAL DE UTILIZARE
Nota: Fotografiile din acest manual sunt doar diagrame schematice. Vă rugăm să citiți “Manualul de Utilizare”
cu atenție, înainte de a utiliza aerul condiționat, pentru a asigura funcționarea corespunzătoare. Păstrați
manualul pentru referințe ulterioare.
ENG
RO
NAVODILA ZA UPRAVLJANJE
Opomba: vse slike v tem priročniku so samo shematski prikazi; standard predstavlja dejansko stanje.
Preden začnete upravljati enoto, natančno in temeljito preberite za priročnik za uporabo. Priročnik shranite
za bodočo uporabo.
SLO
UPUTSTVO ZA UPOTREBU
Napomena: Sve slike u ovom priručniku su samo šematski dijagrami, fizički proizvod je standard. Molimo
Vas da pažljivo i temeljno pročitate ovo uputstvo za upotrebu pre korišćenja uređaja! Sačuvajte ovo
uputstvo za buduću upotrebu.
SRB

3
ENG
Warning: This air conditioner uses R32 flammable refrigerant.
• The room space for the installation, use, repair, and storage of this air conditioner should be greater than 5 m’.
• Air conditioner refrigerant can not charge more than 1. 7kg.
• Do not use any methods to speed up defrost or to clean frosty parts except for particular recommended by
manufacturer.
• Not pierce or burn air conditioner, and check the refrigerant pipeline wether be damaged.
• The air conditioner should be stored in a room without lasting fire source, for example, open flame, burning gas
appliance, working electric heater and so on.
• Notice that the refrigerant may be tasteless.
• The storage of air conditioner should be able to prevent mechanical damage caused by accident.
• Maintenance or repair of air conditioners using R32 refrigerant must be carried out after security check to
minimize risk of incidents.
• Air conditioner must be installed with stop valve cover.
• Please read the instruction carefully before installing, using and maintaining.
Notes: Air conditioner with R32 refrigerant, if roughly treated, may cause serious harm to the human body
or surrounding things.
Incorrect installation or operation by not following these instructions may cause harm or damage to
people, properties, etc.The seriousness is classified by the following indications:
This symbol indicates the possibility of death or serious injury.
This symbol indicates the possibility of injury or damage to properties.
Symbol Note Explanation
WARNING
This symbol shows that this appliance uses a flammable refrigerant.If
the refrigerant is leaked and exposed to an external ignition source,
there is a risk of fire.
CAUTION This symbol shows that the operation manual should be read
carefully.
CAUTION This symbol shows that a service personnel should be handling this
equipment with reference to the installation manual.
CAUTION This symbol shows that information is available such as the operating
manual or installation manual.
WARNING
SAFETY PRECAUTIONS
WARNING!
CAUTION!

4
ENG
WARNING!
• This appliance can be used by children aged from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
(Only for the AC with CE-MARKING)
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to
ensure that they do not play with the appliance. (Except for the AC with CE-MARKING)
• The air conditioner must be grounded. Incomplete grounding may result in electric shocks. Do
not connect the earth wire to the gas pipeline, water pipeline, lightning rod, or telephone earth wire.
• Always switch off the device and cut the power supply when the unit is not in use for long time so as to ensure
safety.
• Take care not let the remote control and the indoor unit watered or being too wet. Otherwise, it may cause short
circuit.
• If the power supply cable is damaged, it must be replaced by manufacture or its service agent or a similar
qualified person.
• Don’t cut off main power switch during operating or with wet hands. It may cause electric shock.
• Don’t share the socket with other electric appliance. Otherwise, it may cause electric shock even fire and
explosion.
• Always switch off the device and cut the power supply before performing any maintenance or cleaning.
Otherwise, it may cause electric shock or damage.
• Don’t pull the power cord when pull out the power plug. The damage of pulling power cord will cause serious
electric shock.
• A warning that ducts connected to an appliance shall not contain an ignition source.
• Don’t install air conditioner in a place where there is flammable gas or liquid. The distance between them
should above 1m. It may cause fire even explosion.
• Don’t use liquid or corrosive cleaning agent wipe the air conditioner and sprinkle water or other liquid either.
Doing this may cause electric shock or damage to the unit.
• Don’t attempt to repair the air conditioner by yourself. Incorrect repairs may cause fire or explosion. Contact a
qualified service technician for all service requirement.
• Don’t use air conditioner in lightning strom weather. Power supply should be cut in time to prevent the
occurrence of danger.
• Don’t put hands or any objects into the air inlets or outlets. This may cause personal injury or damage to the unit.
• Please note whether the installed stand is firm enough or not. If it is damaged, it may lead to the fall of the unit
and cause the injury.
• Don’t block air inlet or air outlet. Otherwise, the cooling or heating capacity will be weakened, even cause
system stop operating.
• Don’t let the air conditioner blow against the heater appliance. Otherwise it will lead to incomplete combustion,
thus causing poisoning.
• The appliance shall be installed in accordance with national wiring regulations.
• An earth leakage breaker with rated capacity must be installed to avoid possible electric shocks.
• This product contains fluorinated greenhouse gases.
• Refrigerant leakage contributes to climate change.
Refrigerant with lower global warming potential (GWP) would contribute less to global warming than a
refrigerant with higher GWP, if leaked to the atmosphere. This appliance contains a refrigerant fluid with a GWP
equal to [675]. This means that if 1 kg of this refrigerant fluid would be leaked to the atmosphere, the impact on
global warming would be [675] times higher than 1 kg of CO2, over a period of 100 years. Never try to interfere
with the refrigerant circuit yourself or disassemble the product yourself and always ask a professional.
• Ensure no following objects under the indoor unit:
1. microwaves, ovens and other hot objects.
2. computers and other high electrostatic appliances.
3. sockets that plug frequently.
• The joints between indoor and outdoor unit shall not be reused, unless after re-flaring the pipe.
• The specification of the fuse are printed on the circuit bord, such as: 3.15A/250V AC, etc.

5
ENG
• Don’t open the windows and doors for long time when the air conditioner is running. Otherwise, the cooling or
heating capacity will be weakened.
• Don’t stand on the top of the outdoor unit or place heavy things on it. This cloud cause personal injuries or
damage the unit.
• Don’t use the air conditioner for other purposes, such as drying clothes, preserving foods,etc.
• Don’t apply the cold air to the body for a long time. It will deteriorate your physical conditions and cause health
problems.
• Set the suitable temperature. It is recommended that the temperature difference between indoor and outdoor
temperature should not be too large. Appropriate adjustments of the setting temperature can prevent the
waste of electricity.
• If your air conditioner is not fitted with a supply cord and a plug, an anti-explosion all-pole switch must be
installed in the fixed wiring and the distance between contacts should be no less than 3.0 mm.
• If your air conditioner is permanently connected to the fixed wiring, a anti-explosion residual current device
(RCD) having rated residual operating current not exceeding 30 mA should be installed in the fixed wiring.
• The power supply circuit should have leakage protector and air switch of which the capacity should be more
than1 .5 times of the maximum current.
• Regarding the installation of the air conditioners, please refer to the below paragraphs in this manual.
• Within the temperature range provided in following table, the air conditioner may stop running and other
anomalies may arise.
• When the temperature is too high, the air conditioner may activate the automatic protection device, so that the
air conditioner could be shut down.
• When the temperature is too low, the heat exchanger of the air conditioner may freeze, leading to water
dripping or other malfunction.
• In long-term cooling or dehumidification with a relative humidity of above 80% (doors and windows are open),
there may be water condenses or dripping near the air outlet.
• T1 and T3 refer to ISO 5151.
WEEE Warning
Meaning of crossed out wheeled dustbin: Do not dispose of electrical appliances as
unsorted municipal waste, use separate collection facilities. Contact you local government for
information regarding the collection systems available. If electrical appliances are disposed
of in landfills or dumps, hazardous substances can leak into the groundwater and get into the
food chain, damaging yourhealth and well-being. When replacing old appliances with new
ones, the retailer is legally obligated to take back your old appliance for disposals at least free
of charge.
CAUTION!
NOTICES FOR USE
The conditions of unit can’t normally run
Cooling Outdoor >43°C (Apply to T1)
>52°C (Apply to T3)
Indoor <18°C
Heating Outdoor >24°C
<-7°C
Indoor >27°C

6
ENG
Notes for heating
Notes for turning off
Emergency operation
Airflow direction adjustment
Specific caution
• The fan of the indoor unit will not start running immediately after the heating is started to avoid blowing out cool
air.
• When it is cold and wet outside, the outdoor unit will develop frost over the heat exchanger which will increased
the heating capacity. Then the air conditioner will start defrost function.
• During defrost, the air conditioner will stop heating for about 5-12 minutes.
• Vapor may come out from the outdoor unit during defrost. This is not a malfunction, but a result of fast defrost.
• Heating will resume after defrost is complete.
• When the air conditioner is turned off, the main controller will automatically decide whether to stop immediately
or after running for dozens of seconds with lower frequency and lower air speed.
• If the remote controller is lost or broken, use force switch
button to operate the air conditioner.
• If this button is pushed with the unit OFF, the air
conditioner will operate in Auto mode.
• If this button is pushed with the unit ON, the air
conditioner will stop running.
1. Use up-down swing and left-right swing buttons on the remote
controller to adjust the airflow direction. Refer to the operation
manual of the remote controller for detail.
2. For models without left-right swing function, the fins has to be
moved manually.
Note: Move the fins before the unit is in operation, or your finger
might be injured. Never place your hand into the air inlet or outlet
when the air conditioner is in operation.
1.Open front panel of the indoor.
2. The connector (as Fig) can not touch the terminal
board, and is positioned as shown in Fig.
Force switch
Connector
Cable 1
Cable 2
Terminal board

7
ENG
NAMES OF EACH PART
Indoor unit
Outdoor unit
Air inlet grille
Panel
Air filter
Air louver
Remote controller
Pipe
protection
ring
Force switch
Air inlet
Air outlet
Air vent
Power cable
Air outlet grille
Air outlet
Connecting
pipe
Drain hose
Note: All the pictures in this manual are just schematic diagrams, the actual is the standard.
Plug, WiFi function, Negative-ion function, and vertical and horizontal; swing function both are optional.

8
ENG
WARNING!
• Before the cleaning of the air conditioner, it must be shut down and the electricity must be cut off for more than
5 minutes, otherwise there might be the risk of electric shocks.
• Do not wet the air conditioner, which can cause an electric shock. Make sure not to rinse the air conditioner with
water under any circumstances.
• Volatile liquids such as thinner or gasoline will damage the air conditioner housing, therefore please clean the
housing of air conditioner only with soft dry cloth and damp cloth moistened with neutral detergent.
• In the course of the using, pay attention to cleaning the filter regularly, to prevent the covering of dust which
may affect the effect. If the service environment of the air conditioner is dusty, correspondingly increase the
number of times of cleaning. After removing the filter, do not touch the fin part of the indoor unit with the finger,
and no force to damage the refrigerant pipeline.
Clean the panel
Clean the air filter
Check before use
Remove the air filter
Clean the Air Filter
Mount the Filter
When the panel of the indoor unit is contaminated, clean it gently with a wrung towel using tepid water below
40°C, and do not remove the panel while cleaning.
1. Use both hands to open the panel for an angle from both ends of the panel in accordance with the direction of
the arrow.
2. Release the air filter from the slot and remove it.
Use a vacuum cleaner or water to rinse filter, and if the filter is very dirty (for example, with greasy dirt),
clean it with warm water (below 45 °C) with mild detergent dissolved in, and then put the filter in
the shade to dry in the air.
1. Check whether all the air inlets and outlets of the units are unblocked.
2. Ceck whether there is blocking in the water outlet of the drain pipe, and immediately clean it up if any.
3. Check the ground wire is reliably grounded.
4. Check whether the remote control batteries are installed, and whether the power is sufficient.
5. Check whether there is damage in the mounting bracket of the outdoor unit, and if any, please contact our local
service center.
1. Reinstall the dried filter in reverse order of removal, then cover and lock the panel.
CLEAN AND CARE

9
ENG
Maintain after use
TROUBLESHOOTING
1. Cut off the power source of the air conditioner, turn off the main power switch and remove the batteries from the
remote controller.
2. Clean the filter and the unit body.
3. Remove the dust and debris from the outdoor unit.
4. Check whether there is damage in the mounting bracket of the outdoor unit, and if any, please contact our local
service center.
Do not repair the air conditioner by yourself as wrong maintenance may cause electric shock or fire or explode,
please contact the authorized service center and let the professionals conduct the maintenance, and checking the
following items prior to contacting for maintenance can save your time and money.
CAUTION!
Phenomenon Troubleshooting
The air conditioner does
not work.
• There might be power outages. → Wait until power is restored.
• Power plug may be loose out from the socket. → The plug in the plug tightly.
• Power switch fuse may blow. → Replace the fuse.
• The time for timing boot is yet to come. → Wait or cancel the timer settings.
The air conditioner can’t
run after the immediate
start-up after it is shut
down.
• If the air conditioner is turned on immediately after it is turned off, the protective
delay switch will delay the operation for 3 to 5 minutes.
The air conditioner stops
running after it starts up
for a while.
• May reach the setting temperature. → It is a normal function phenomenon.
• May be at a defrosting state. →It will automatically restore and run again after
defrosting.
• Shutdown Timer may be set. → If you continue to use, please turn it on again.
The wind blows out, but
the cooling/ heating
effect is not good.
• Excessive accumulation of dust on filter, blocking at air inlet and outlet, and the
excessively small angle of the louver blades all will affect the cooling and heating
effect. → Please clean the filter, remove the obstacles at the air inlet and outlet
and regulate the angle of the louver blades.
• Poor cooling and heating effect caused by doors and windows opening, and
unclosed exhaust fan. →Please close the doors, windows, the exhaust fan, etc.
• Auxiliary heating function is not turned on while heating, which may lead to poor
heating effect. →Turn on the auxiliary heating function. (only for models with
auxiliary heating function)
• Mode setting is incorrect, and the temperature and wind speed settings are not
appropriate. →Please re-select the mode, and set the appropriate temperature
and wind speed.
The indoor unit blows
out odor.
• The air conditioner itself does not have undesirable odor. If there is odor, it may
be due to accumulation of the odor in the environment. →Clean the air filter or
activate the cleaning function.
There is sound of
running water during
the running of air
conditioner.
• When the air conditioner is started up or stopped, or the compressor is started
up or stopped during the running, sometimes the “hissing” sound of running
water can be heard. → This is the sound of the flow of the refrigerant, not a
malfunction.

10
ENG
Phenomenon Troubleshooting
A slight “click” sound is
heard at the of start-up
or shut-down.
• Due to temperature changes, panel and other parts will swell, causing the sound
of friction. → This is normal, not a fault.
The indoor unit makes
abnormal sound.
• The sound of fan or compressor relay switched on or off.
• When the defrosting is started or stop running, it will sound. → That is due to the
refrigerant flowed to reverse direction. They are not malfunctions.
• Too much dust accumulation in the air filter of the indoor unit may result in
fluctuation of the sound. →Clean the air filters in time.
• Too much air noise when “Strong wind” is turned on. →This is normal, if feeling
uncomfortable, please deactivate the “Strong wind” function.
There are water drops
over the surface of the
indoor unit.
• When ambient humidity is high, water drops will be accumulated around the air
outlet or the panel, etc. → This is a normal physics phenomenon.
• Prolonged cooling run in open space produces water drops. → Close the doors
and windows.
• Too small opening angle of the louver blades may also result in water drops at
the air inlet. → Increase the angle of the louver blades.
During the cooling
operation, the indoor
unit outlet sometimes
will blow out mist.
• When the indoor temperature and humidity are high, it happens sometimes.
→ This is because the indoor air is cooled rapidly. After it runs for some time, the
indoor temperature and humidity will be reduced and the mist will disappear.
Immediately stop all operations and cut off the power supply, contact our Service center locally in
following situations.
• Hear any harsh sound or smell any awful odor during running.
• Abnormal heating of power cord and plug occurs.
• The unit or remote controller has any impurity or water.
• Air switch or leakage protection switch is often disconnected.
IMPORTANT NOTICES!
NOTICES FOR INSTALLATION
Unpacking Inspection
• Before installating, please contact with local authorized maintenance cenler, if unit is not installed by the
authorized maintenance center, the malfunction may not solved,due to discommodious contact.
• The air conditioner must be installed by professionals according to the national wiring rules and this manual.
• Refrigerant leak tesf must be made after installation.
• To move and install air conditioner to another place, please contact our local special service center.
• Open the box and check air conditioner in area with good ventilation (open the door and window) and without
ignition source.
Note: Operators are required to wear anti-static devices.
• It is necessary to check by professional whether there is refrigerant leakage before opening tlie box of outdoor
machine; stop installing the air conditioner if leakage is found.
• The fire prevention equipment and anti-static precautions shall be prepared well before checking.Then check
the refrigerant pipeline to see if there is any collision traces, and whether the outlook 1s good.

11
ENG
Safety Principles for Installing Air Conditioner
Requirements For Installation Position
• Fire prevention device shall be prepared before installation.
• Keep installing site ventilated.(open the door and window)
• Ignition source,smoking and calling is not allowed to exist in area where R32 refrigerant rocated.
• Anti-static precautions in necessary for installing air conditioner, e.g. wear pure cotton clothes and gloves.
• Keep leak detector in working state during the installation.
• If R32 refrigerant leakage occurs during tfle installation, you shall immediately detect the concentration in indoor
environment until it reaches a safe level. If refrigerant leakage affects the performance of the air conditioner,
please immediately stop the operation, and the air conditioner must be vacuumed firstly and be returned to the
maintenance station for processing.
• Keep electric appliance, power switch, plug, socket, high temperature heat source and high static away from the
area underneath sidelines of the indoor unit.
• The air conditioner shall be installed in an accessible location to installation and maintenance, without obstacles
that may block air inlets or outlets of indoor/outdoor units, and shall keep away from heat source inflammable or
explosive conditions.
• When installing or repairing the air conditioner and the connecting line is not long enough, the entire
connecting line shall be replaced with the connecting line of the original specification; extension is not allowed.
• Use new connection pipe, unless re-flaring the pipe.
• Avoid places of inflammable or explosive gas leakage or where there are strongly aggressive gases.
• Avoid places subject to strong artificial electric/magnetic fields.
• Avoid places subject to noise and resonance.
• Avoid severe natural conditions (e.g. heavy lampblack, strong sandy wind, direct sunshine or h1gli temperature
heat sources).
• Avoid places within the reach of cnildren.
• Shorten the connection between the indoor and outdoor units.
• Select where it is easy to perform service and repair and where the ventilation good.
• The outdoor unit shalrnot be installed in any way that could occupy an aisle, stairway, exit, fire escape, catwalk or
any other public area.
• The outdoor unit shall be installed as far as possible from the doors and windows of the neighbors as well as the
green plants.
Installation environment inspection
• Check nameRlate of outdoor unit to make sure whether the refrigerant is R32.
• Check the floor space of the room. The space shall not be less than usable space(sm2 ) in the specification.The
outdoor unit shall be installed at a well-ventilated place.
• Check the surrounding environment of installation site: R32 shall not be installed in the enclosed reserved space
of a building.
• When using electric drill to make holes in the wall, check first whether there is pre-buried pipeline for water,
electricity and gas.
• It is suggested to use the reserved hole in the roof of tfle walr
Requirements of the mounting structure
• The mounting rack must meet the relevant national or industrial standards in terms of strength with welding and
connection areas rustproofed.
• The mounting rack and its load carry surface shall be able to withstand 4 times or above the weight of the unit,
or 200kg, whichever is heavier.
• The mounting rack of the outdoor unit shall be fastened with expansion bolt.
• Ensure the secure installation regardless of what type of wall on which it is installed, to prevent potential
dropping that could hurt people.

12
ENG
Requirements for operations at raised height
Grounding Requirements
Others
Electrical Safety Requirements
• When carrying out installation at 2m or higher above the base level, safety belts must be worn and ropes of
sufficient strength be securely fasten to the outdoor unit, to prevent falling that could cause personal injury or
death as well as property loss.
• The air conditioner is the class I electrical appliance and must ensure a reliable grounding.
• Do not connect the grounding wire to a gas pipe, water pipe, lightning rod, telephone line, or a circuit poorly
grounded to the earth.
• The grounding wire is specially designed and shall not be used for other purpose, nor shall it be fastened with a
common tapping screw.
• Interconnection cord diameter should be recommended as per instruction manual ,and with type O terminal
that meet local standards (internal diameter of type O terminal needs to match the screw size of the unit, no
more than 4.2mm). After installation, check the screws whether have been fixed effectively, and there is no risk
of loosening.
• The connection method of the air conditioner and the power cord and the interconnection method of each
independent element shall be subject to the wiring diagram affixed to the machine.
• The model and rating value of the fuse shall be subject to the silkscreen on corresponding controller or fuse
sleeve.
• Be sure to use the rated voltage and air conditioners dedicated circuit for the power supply, and the power cord
diameter must meet the national requirements.
• When the maximum current of air conditioner is ≥16A, it must use the air switch or leakage protection switch
equipped with protection devices.
• The operating range is 90%-110% of the local rated voltage. But insufficient power supply malfunction, electrical
shock, or fire. If the voltage instability, proposed to increase the voltage regulator.
• The minimum clearance between the air conditioner and the combustibles is 1.5 m.
• The interconnection cord connect the indoor and outdoor units. You must first choose the right cable size
before preparing it for connection.
• Cable Types: Outdoor Power Cable: H07RN-F or H05RN-F;
Interconnection cord: H07RN-F or H05RN-F;
• Minimum Cross-Sectional Area of Power cable and interconnection cord.
• The size of the interconnection cord, power cable, fuse, and switch needed is determined by the maximum
current of the unit. The maximum current is indicated on the nameplate located on the side panel of the unit.
Refer to this nameplate to choose the right cable, fuse, or switch.
• Note: Core number of cable refer to the detailed wiring diagram adhered on the unit which you purchased.
Appliance
Amps (A) AWG
10 18
13 16
18 14
25 12
30 10
40 8
Rated Current of
Appliance (A)
Nominal Cross-Sectional
Area (mm2)
>3 and ≤ 6 0.75
>6 and ≤10 1
>10 and ≤16 1.5
>10 and ≤16 2.5
>10 and ≤16 4
>10 and ≤16 6
North America Other regions

13
ENG
INSTALL INDOOR UNIT
Dimension drawing of indoor unit installation
Space to the ceiling
Space to the floor
Space to the wallSpace to the wall
15cm above
20cm above20cm above
200-260cm
Mounting plate
Wall-through Hole
1. The wall for installation of the indoor unit shall be hard and
firm, so as to prevent vibration.
2. Use the “+” type screw to fasten the peg board, horizontally
mount the peg board on the wall, and ensure the lateral
horizontal and longitudinal vertical.
3. Pull the peg board by hand after the installation, to confirm
whether it is solid.
1. Make a hole with an electric hammer or a water drill at the
predetermined position on the wall for piping, which shall
slant outwardly by 5° -10° .
2. To protect the piping and the cables from being damaged
running through the wall, and from the rodents that may
inhabit in the hollow wall, a pipe protecting ring shall be
installed and sealed with putty.
Note: Usually, the wall hole is ɸ60mm~ɸ80mm. Avoid pre-
buried power wire and hard wall when making the hole.
Pipe protection
ring
Putty

14
ENG
Route of Pipeline
Drain pipe connection
Wrap the Piping
1. Depending on the position of the unit, the piping may be routed sideway from the left or the right (Fig 1), or
vertically from the back (Fig 2) (depending on the pipe length of the indoor unit). In the case of sideway routing,
cut off the outlet cutting stock of the opposite side.
1. Remove the fixed part to pull out pipe of indoor machine from the case. Screw the hexagon nut in the left of the
joint to the end with your hand.
2. Connect the connecting pipe to the indoor unit:
Aim at the pipe center, tighten the Taper nut with fingers, and then tighten the Taper nut with a torque wrench,
and the direction is shown in diagram on the right.The torque used is shown in the following table.
Note: Carefully check if there is any damage of joints before installation.
The joints shall not be reused, unless after re-flaring the pipe.
1. Use the insulation sleeve to wrap the joint part the indoor
unit and the connection pipe, and then use insulating
material to pack and seal insulation pipe, to prevent
generation of condensate water on the joint part.
2. Connect the water outlet with drain pipes, and make the
connection pipe, cables, and the drain hose straight.
3. Use plastic cable ties to wrap the connecting pipes, cables
and drain hose. Run the pipe sloping downward.
Connecting Pipe
Drain Hose and
Cables Connecting Pipe
Drain Hose and
Cables
Outlet material preparation
Fig 2
Fig 1
The size of pipe (mm) Torque (Nm)
ɸ6 / ɸ6. 35 15 ~ 88
ɸ9 / ɸ9. 52 35 ~ 40
ɸ12 / ɸ12.7 45 ~ 60
ɸ15.88 73 ~ 78
ɸ19.05 75 ~ 80
Tightening torque table
Indoor unit pipe
Spanner Torgue wrench
Connecting Pipe
Drain Hose
and Cables
Plastic Strap
Taper nut Connecting
pipe

15
ENG
Fixing the Indoor Unit
1. Hang the indoor unit on the peg board, and move the
unit from left to right to ensure that the hook is properly
positioned in the peg board.
2. Push toward the lower left side and the upper right side of
the unit toward the peg board, until the hook is embedded
in the slot and makes a “click” sound.
Wiring diagram
• If your air conditioner is provided with interconnection cord , the wiring of the indoor unit is connected in the
factory, there is no need of connection.
• If the interconnection cord is not provided, connection is needed in accordance with the
After installation, check:
1. The screws whether have been fixed effectively, and there is no risk of loosening.
2. Connector of display board whether put in the right place and do not touch the terminal board.
3. Control box cover whether cover tightly.
If there is a connector,
connect it directly.
Constant speed
To Outdoor unit
To Outdoor unit
To Outdoor unit
To Outdoor unit
Variable speed Connector
NOTE:
• This manual usually includes the wiring mode for the different kind of A/C. We cannot exclude the possibility that
some special type of wiring diagrams are not included.
• The diagram are for reference only. If the entity is difference with this wiring diagram, please refer to the detailed
wiring diagram adhered on the unit which you purchased.

16
ENG
REMOTE CONTROLLER INSTRUCTIONS
Attention
• Read this “instructions” carefully so that you can use the air-conditioner safely and correctly.
• Take good care of the “instructions” so that it can be referred to at any time.
1. Aim the remote controller towards the receiver on the airconditioner.
2. The remote controller should be within 8 meters away from the receiver.
3. No obstacles between the remote controller and receiver.
4. Do not drop or throw the remote controller.
5. Do not put the remote controller under the forceful sun rays or heating facilities and other heating sources.
6. Use two 7# batteries, do not use the electric batteries.
7. Take the batteries out of remote controller before stop its using for long.
8. When the noise of transmitting signal can’t be heard indoor unit or the transmission symbol on the display
screen doesn’t flare, batteries need be replaced.
9. If reset phenomenon occurs on pressing the button of the remote controller, the electric quantity is deficient
and new batteries need to be substituted.
10. The waste battery should be disposed properly.
Note:
• The picture is general remote controller, contains almost all of the function buttons. They may be slightly
different from material abject(depend on model).
• All the figures above are the displays after being initially electrified or re-electrified after power off. In actual
operations, the remote controller screen displays related items only.
• The cooling only units don’t have the function of heating or electric heating. When the remote controller turns to
such function buttons, the units will not result such effect. Please don’t turn the remote controller to such buttons.

17
ENG
Instructions of remote controller
ECO
Turbo
“ON/OFF”
UP and down swinging
Timer
Fan speed
Temperature addtion
Mode
Left and right swinging
Temperature reduction
Sleep
1. The icon meaning of remote controller
1. The remote controller is equipped with 11 buttons, and the LCD .
2. At the first power on, the LCD of the remote controller displays all the icons first and then enters the standby
state, displaying only the mode icon.
3. Introduction of LCD screen icon:
• Mode display: automatic , cooling , dehumidification , fan and heating .
• Temperature display: displays temperature, which range between16~32�C or 61~90�F
• Wind speed display: means wind speed.
• Swinging display: means external pendulum wind.
means internal pendulum wind.
• Timer display: means TIME ON. means TIME OFF.
• Other display: means sleep; means TURBO; means ECO; means electric heating;
means lock; means lamplight.
2. Button function of remote controller
ON/OFF:
When pressing this key, the remote controller switches by “on, off, on” circularly.
Mode:
1. When pressing this key, the remote controller switches by “automatic, cooling, dehumidification, fan, heating,
automatic” circularly.
2. In dehumidification mode, the setting temperature of the internal machine is 25 degree C. The remote

18
ENG
controller does not display the setting temperature and is not adjustable.The internal pendulum wind stays
unchanged according to the state before switching, but the external pendulum wind is forced to close.
Temperature reduction -
1. Temperature setting: when pressing this key, the setting temperature will be reduced by “32°C, 31 °C, .......,
17°C, 16°C “. (When pressing this key in dehumidification and fan mode, the temperature will not change).
2. Keep pressing will continuously change the temperature.
Temperature addition +
1. Temperature setting: when pressing this key, the setting temperature will be added by “16°C, 17°C, ......., 31°C,
32°C”, (When pressing this key in dehumidification and fan mode, the temperature will not change).
2. Keep pressing will continuously change the temperature.
Up and down swinging (External pendulum wind)
1. Pressing this key in the dehumidification mode, the external pendulum wind is forced to close.
2. Pressing this key in the other modes, the external pendulum switches by “swing, fixed wind, swing” circularly.
Left and right swinging (Internal pendulum wind):
1. Pressing this key in the dehumidification mode, the internal pendulum wind stays unchanged according to the
state before switching.
2. Pressing this key in the other modes, the internal pendulum switches by “swing, stop, swing” circularly.
FAN:
1. When the first power on, the remote controller is set to the automatic wind speed by default. In
dehumidification mode, the wind speed is fixed to low wind and is not adjustable. By pressing the wind speed
key, there is no response to the remote controller.
2. Pressing this key in the other modes, the wind speed switches by “automatic wind speed, low speed, middle
speed, high speed, automatic wind speed “ circularly.pendulum switches by “swing, stop, swing” circularly,
high speed, automatic wind speed “ circularly.
Timer:
1. Under the shutdown state, press this key to set the opening time, range from 1 hour to 24 hour.
2. Under the boot state, press this key to set the shutdown time, range from 1 hour to 24 hour.
3. The timing time is according to the cycle of “1h, 2h, ......., 23h, 24h, cancel, 1h”.
4. Exit timing adjustment after 3 seconds without key pressing.
TURBO:
1. Extension code remote controller has the effect. The remote controller is no TURBO by default, and the
TURBO key will not work in automatic mode, dehumidification mode and fan mode.
2. Pressing this key in the cooling or heating mode, the TURBO mode switches between opening and closing.
When in the TURBO mode, it still displays the wind speed. Switching mode or entering sleep function will
close TURBO mode.
3. If the air conditioner has TURBO mode, pressing this key, the remote controller still displays current
windshield, and indoor unit runs with the highest wind.
ECO:
1. The remote controller is no ECO by default, and the ECO key will not work in automatic mode,
dehumidification mode and fan mode.
2. Pressing this key in the cooling or heating mode, the ECO mode switches between opening and closing.
When in the ECO mode, the setting temperature is set to 26°C (79°F) and other settings are unchanged. If
closing ECO mode, the remote controller will recover to the setting before opening ECO mode. Switching
mode will close ECO mode.
SLEEP:
1. Pressing this key in the modes except of the fan mode, the sleep function switches between opening and
closing. Switching mode will cancel sleep function.
2. When pressing this key, the wind speed is automatically switched to low wind. However, the wind speed can
be adjusted according to the wind speed key (except of the dehumidification mode).
LIGHT
1. When the first power on, there is no lamplight by default. Pressing Fan key 3S force to turn off or turn on the
lamplight. Decide whether to have this function according to the actual model.

19
ENG
LOCK
1. There is no lock by default. Pressing Sleep key 3S, the lock function switches between opening and closing.
Electricheating (Optional)
1. Pressing Timer key 3S, the electric heating function switches between opening and closing.
2. It only works in heating mode, switch heating mode, the default on.
CLEAN (Optional)
1. The remote controller is no CLEAN by default.Pressing TURBO key 3S, the CLEAN function switches between
opening and closing.Decide whether to have this function according to the actual model.
IFEEL (Optional)
1. The remote controller is no IFEEL by default. Pressing ECO key 3S, the IFEEL function switches between
opening and closing.Decide whether to have this function according to the actual model.
Distribution function
1. Press the TURBO 10 times or more continuously within 20 seconds until the lamplight displays A P. Decide
whether to have this function according to the actual model.
Combinatorial key: “Mode +ECO”
1. On the shutdown interface, press the combinatorial key on the remote controller for 5 seconds to enter the
address setting interface, the address displayed by the remote controller after entering is the address retained
last time. When controlling the wired controller by remote controller, press the mode key to query the address,
querying address remote controller interface does not display, the wired controller can display.
2. At the address setting interface, press the temperature addition or reduction to adjust the setting address,
and it ranges from 00 1 ... 99 00. Press the ON / OFF key to enter the sending state and send the
address setting code.
3. Press the combinatorial key on the remote controller for 5 seconds to exit the address setting interface. If there
is no key pressing associated with address setting for more than 30 minutes, the remote controller will exit the
address setting interface.
Combinatorial key: “TIMER” + “SLEEP”(Optional)
1. Pressing the combinatorial key on the remote controller for 3 seconds, the ionizer function switches between
opening and closing.
2. The ionizer function works in any mode. When the ionizer function is ON, if turn off the unit, the ionizer
function will be closed at same time and it is still closed after turning on the unit again.
Smart WiFi app user manual can be found at:
https://tesla.info/wp-content/uploads/pdf/TeslaTCWiFiapp.pdf

20
RO
Atentie: Acest aparat de aer conditionat utilizeaza agentul frigorific R32 inflamabil.
• Spatiul pentru instalarea, utilizarea, repararea si depozitarea acestui aparat de aer conditionat trebuie sa fie mai
mare de 5 m.
• Agentul frigorific al aerului conditionat nu poate incarca mai mult de 1,7 kg.
• Nu utilizati alte metode pentru a accelera dezghetarea sau pentru a curata partile inghetate, cu exceptia
cazurilor speciale recomandate de producator.
• Nu aruncati sau ardeti aparatul de aer conditionat si verificati daca conductele de agent frigorific sunt
deteriorate.
• Aparatul de climatizare trebuie depozitat intr-o incapere fara sursa de incendiu de durata, de exemplu: flacara
deschisa, aparat de ardere a gazului, incalzitor electric si asa mai departe.
• Depozitarea aparatelor de aer conditionat trebuie sa previna deteriorarea mecanica cauzata de accident.
• Mentinerea sau repararea aparatelor de climatizare folosind agentul frigorific R32 trebuie sa fie efectuate dupa
verificarea de securitate, pentru a minimiza riscul de incidente.
• Aerul conditionat trebuie instalat cu capacul supapei de oprire.
• Va rugam sa cititi instructiunile cu atentie inainte de instalare, utilizare si intretinere.
Observatii: Aparatul de racire cu agent frigorific R32, daca este tratat cu duritate mare, poate cauza
probleme grave, daunand corpului uman sau lucrurilor din jur.
Instalarea incorecta sau functionarea prin nerespectarea acestor instructiuni poate provoca vatamari sau
daune persoanelor, proprietatilor etc. Gravitatea este clasificata dupa urmatoarele indicatii:
Acest simbol indica posibilitatea de deces sau vatamari grave.
Acest simbol indica posibilitatea ranirii sau deteriorarii proprietatilor.
Simbol Nota Explicatie
Avertizare
Acest simbol arata ca acest aparat utilizeaza un agent frigorific
inflamabil. Daca agentul frigorific este scurs si expus la o sursa
externa de aprindere, exista riscul de incendiu.
Masuri de
precautie Acest simbol arata ca manualul de operare trebuie citit cu atentie.
Masuri de
precautie
Acest simbol arata ca service-ul trebuie sa se ocupe de acest
echipament cu referire la manualul de instalare.
Masuri de
precautie
Acest simbol arata ca sunt disponibile informatii, cum ar fi manualul
de operare sau manualul de instalare.
ATENTIE
MASURI DE SIGURANTA
ATENTIE!
PRUDENTA!