Test Equipment Depot 8901 User manual

OPERATION MANUAL
RS232
REMOTE VANE
DIGITAL ANEMOMETER
CE
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

A. Measuring Air Velocity (Single point)
Feet per Minute (FPM).
B. Continuous Moving Average.
C. MIN/MAX/AVG reading on a single
point.
D. Air Velocity average for multiple
points .
E. Non Sleep Mode(Bypass auto power
off).
F. Default setting ( Imperial/ Metric)
G. RS232 interface setting.
H. Auto power off function.
I. Direct measuring of air flow
(Single point) CFM
J. Obtain air flow (CFM) average
for multi-point
FEATURES
Typical Measurement
a) Please placethe meter inthe
airstream. Make surethat the
airstream and thesensor
are aligned asshown ( 20
degrees maximum).
b) 3 secondsfor the
reading to stabilize.
o
20
o
20
Rear side
2

1.ON/OFF. Power on or off .
2.HOLD SET/SAVE. Freezs the reading.
Adjust the digit to the value needed.
3.SEL/AVG ,NXT DGT-> MULTI-P.
AVERAGE . Display the average of
all the measurements. Select the next
digit for editing.
4.MN/MX REC SINGLE-P
View the minimum or maximum ,
average or record value .
5.MODE :
VELOCITY .Air Velocity in FPM .
FREE AREA. Enter area value .
VOLUME. Air Volume mode.
BUTTON / DISPLAY
FRONT PANEL DESCRIPTION
3

MIN
mil/h cfm
AVG
REC
FLOW
km/h cms
AREA
m/s
vel Hold PH Knots
ft/m 2
ft
2
m
MAX
INDICATORS
16. Primary readout-Numerical display
for Air Velocity/ Air Volume/Free
area digit
17. Secondary readout -Temperature
display or records number.
18. "-" Polarity indicator for negative
temperature.
19. Knots.
20. Mil/h.
21. Km/h.
1850 meters per hour
Miles per hour
Kilometer per hour
1.vel.
Air velocity measurement.
2.FLOW. Air Flow/Air volume.
3.AREA. Free area degault setting.
4.Hold. Freezs the reading.
5.ft/m.
m/s
Feet per minute.(imperial)
Meter per second.(metric)
2
6.ft . Feet square.(imperial)
7.m .
2meter square.(metric)
8.cfm. Cubic feet per minute.
9.cms. Cubic meter per second.
10.C. Celsius unit.
11.F. Fahrenheit unit.
12.REC. Record and saved.
13.AVG. Average data
14.MIN. Minimum data
15.MAX. Maximum data
4

B. CONTINUOUS MOVING AVERAGE
1. Turn the power ON .
2. Place sensor in front of air flow
source.
3. Press MN/MX record key once.
An "AVG" in the lower left corner
of the display confirms the meter
is in the continuous moving average
measurement mode. The display
will update once per second.
(See Fig.3)
The meter has the ability to display
continuous moving average for up to
two(2) hours.
1. Press the ON/OFF button and turn
meter on. Meter will show full display
when first powered on in 5 seconds.
(See Fig.1)
2. Unit is ready for use when LCD display
shows "vel" at upper left corner and
temperature at lower right corner.
(See Fig.2)
A. MEASURING AIR VELOCITY
(SINGLE POINT) FEET PER
MINUTE (FPM)
Fig.1 Fig.2
Fig.3
vel
m/s
MIN
cfm
AVG
REC
FLOW
cms
AREA
m/s
vel Hold
ft/m 2
ft
2
m
MAX
AVG
vel
m/s
5

C. MIN/MAX/AVG READING ON A
SINGLE POINT
1. Power unit ON.
2. Place sensor in front of air flow
source.
3. Press MN/MX REC SINGLE-P
key. The unit will begin to record
the readings.
The meter displays the average
velocity by default. (See Fig.C-1)
Each press of the MN/MX button
cycles the display through:
* Real-time readings.
* MIN velocity.(Fig.C-2)
* MAX velocity.(Fig.C-2)
* Back to AVG velocity.(Fig.C-1)
To obtain MIN/MAX/AVG readings on a
single point.
6
AVG
REC
m/s
vel
MIN REC
m/s
vel
REC
m/s
vel
MAX
Fig.C-1
Fig.C-2
Fig.C-3

Press the HOLD key before removing the
unit from the air source.Press the MIN/
MAX REC SINGLE-POINT key to view
the stored data which will appear in the
following order :
Instantaneous measurement
Minimum
Maximum
Average
To clear the current MIN/MAX average
readings, turn off the power or press
and hold MN/MX key until unit beeps
twice, then release.
1. Turn the meter on and position the
vane at the first point to be measured.
soon as the first measurement is
completed press the HOLD key,(you
will hear a single beep), and release.
The display will show HOLD above
the reading. (See Fig.4)
D. AIR VELOCITY AVERAGE FOR
MULTIPLE POINTS
Fig.4
vel Hold
m/s
2. Press the MN/MX key,(You will hear
a single beep), and release,( the
display will show a digit 1-8). This
number represents the point that is
being recorded.(See Fig.5)
Hold anucinator and point at the
lower corner will be disappeared in
one second.
7

3. Once all measurements have been
recorded press SEL/AVG key.
The unit will display the average air
velocity reading and number of points
measured. ( See Fig.5-1) as an
example of stored 8 points shows
average air velocity measurement.
Fig.5
Repeat this process until all desired
points have been measured and
recorded, A maximum of 8 points may
be recorded at one time.
8
vel Hold
m/s
ll
ll
ll
ll
Fig.5-1
AVG
m/s
vel Hold
Fig.6
E. NON SLEEP MODE
(Bypass auto power off)
Power unit off;press ON/OFF & HOLD at
the same time and then release ON/OFF
only. An "n" appears on the LCD then
you can release the HOLD key. The
meter will remain on until the ON/OFF
button is pressed.(See Fig.6 )

Fig.7
Fig.8
The default measuring units can be
changed by following the steps below.
The unit should be turned off before
commencing.
m/s
m/s
ft/m
1. Press and hold the SEL/AVG key,
then press the ON/OFF key once to
turn the unit on. When the LCD
oo
displays " ft/m,ms " and " C, F"
release the SEL/AVG key.(Fig.7)
2. To choose metric units press the
HOLD key. The LCD should display "
o
m/s, C". (See Fig.8)
F. HOW TO CHANGE THE DEFAULT
SETTING/IMPERIAL TO METRIC
Vice Versa(METRIC TO IMPERIAL)
9
To choose the imperial units press the
SEL/AVG key. The LCD should display
o
"ft/m, F" (See Fig.9).
ft/m
Fig.9

3. Press the MN/MX REC key, the LCD
should display "S" (See Fig.10) .
Then press the HOLD key. The LCD
display 2400 or 1200 (pre-setting).
(If Baud rate change is needed, please
refer to step G.1) (See Fig.11)
4. Press the MN/MX REC key again,
the LCD should display "S" again.
(See Fig.10) .Then press the HOLD
key, the LCD will revert to a normal
measurement display. The default
setting is now completed.(See Fig.12)
5. Press HOLD key for measuring the
current air velocity / temperature with
pre-setting unit . A "HOLD" above the
display is disappeared now.
Note: Without pressing HOLD key,
display is freezing .
Fig.10
Fig.12
G.SETTING THE RS232 OUTPUT
(Optional accessory)
m/s
vel Hold
Fig.11
10

Fig.14
AREA
2
ft
H. AUTO POWER OFF
Air Velocity measurement is calculated
by multiplying the air velocity readings
by the free area dimensions. Free area
is published by the grill and register
manufacturer you are servicing. You must
first determine the free area of the air
source before entering it into the meter.
1. Power unit on
2. Press MODE once (you will hear one
beep). Meter will display"AREA" in
upper case lettering and "1.111" will
appear (See Fig.14) .
The first digit will be flashing.
3. Press the HOLD key to increase the
number.
4. Press the SEL/AVG key to advance
to next number. Follow Step 3 and
repeat.
5. Press the MODE key once all digits
have been entered. The word "flow"
will appear.
I. DIRECT MEASURING OF AIR
FLOW (SINGLE POINT) CFM
The unit will turn off automatically
after 20 minutes to save the battery.
Press ON/OFF and HOLD button to
disable Auto Power Off function.
12
The meter is now ready to measure air
flow(CFM).

TO CLEAR MEMORY OF CURRENT
MULTI- POINT AVERAGE READINGS.
Press and hold SEL/AVG key until unit
beeps twice, then release. Unit must be
in velocity/FPM mode in order to clear
current average readings.
J. TO OBTAIN AIR FLOW (CFM)
AVERAGE FOR MULTIPOINTS
Simply complete steps 1~3 in D.
Once all the multi-point average is
determined:
1. Press MODE button once and confirm
correct free area setting is locked into
instrument. (if free area setting must
be adjusted make necessary changes
now.)
2. If free area setting is correct press
MODE button again to enter air flow
mode.
3. Unit will now display average air flow
reading and number of points
measured.
The meter's free area dimension has
been set to 1.111 square feet, a most
commonly used free area dimension in
the U.S.A. If you want to measure the air
flow for a single point without changing
the area dimension, please power on the
meter, position the fan and then press the
MODE key twice, you will be into the air
flow(CFM) mode and the air flow(CFM)
displayed is equal to the current air
velocity reading (FPM x FREE AREA =
CFM) times the 1.111 square feet.
13

We would suggest to set the free area
dimension before you start measuring
the air velocity so after you measure the
air velocity, you can jump to the air flow
mode to view the cubic feet per minute
without further changing the free area
dimension.
3
CFM (ft /min)
2
= Air Velocity (ft/min)xArea (ft )
3
CMM (m /min)
2
= Air Velocity (m/sec)xArea (m ) x 60
Cubic equations:
Units Conversion Table:
1 m/s=
1 ft/min=
1 knots=
1 km/hr=
1 mph=
m/s
1
0.00508
0.5144
0.2778
0.4464
ft/min
196.87
1
101.27
54.69
87.89
knots
1.944
0.00987
1
0.54
0.8679
1 m/s=
1 ft/min=
1 knots=
1 km/hr=
1 mph=
km/hr
3.6
0.01829
1.8519
1
1.6071
mph
2.24
0.01138
1.1523
0.6222
1
Note:
On initial start up the unit will display
pH, knots. (See Fig.15)
MIN
mil/h cfm
AVG
REC
FLOW
km/h cms
AREA
m/s
vel Hold PH Knots
ft/m 2
ft
2
m
MAX
Fig.15
14

TROUBLE SHOOTING
? LOW BATTERY
When the reading of display is flashing,
or no display , please change the 9 volt
battery in the meter .
Replace battery procedure:
Remove the screw from the lower back
of the meter. Lift the panel out and
remove the battery .Reverse the process
to install a new battery and replace the
cover .
? E6
Indicates the related circuits or parts of
thermistor are failed. Send them back to
the store you have bought for repairing.
? SENSOR'S FAN WILL NOT TURN
Indicates the sensor fan is damaged ,
purchase new sensor probe .
Note:
Manufacturer's part number is
VY890PAZ.
1.The meter x 1
2.Battery x 1 (9.0 volt)
3.Operation manual x 1
4.Hard carry case x 1
Optional accessory:
a) RS232 software CD-R.
b) D-sub connector.
MATERIAL SUPPLIED
This standard package contains:
15

RS232 output :
TXXX.XF, VXXXXFTM
TXXX.XC, VXXXXMPS
SPECIFICATIONS Resolu-
tion Accuracy
Airflow Range
Temperature
Battery Life 100 Hours
Display Type LCD
Display Size 37mm x 42mm(1-1/4" x 1- 5/8")
Max Reading 9999
Dimensions 181mm(L)x71mm(W)x38mm(D)
Fan Diameter 70mm(2-7/8")
Auto power off :
Approx. 20 minutes
o
Operating Humidity : Max. 90% RH(0~35 C)
o
o
+14 F to 122 F 0.1 o
1.0 F
oo
-10 C to 50 C 0.1 o
0.6 C
80-6900 ft/min 12%FS
0.4-35 m/sec 0.01 2%FS
GENERAL SPECIFICATION
16
RS232 OUTPUT:
The meter can link with personal
computer to capture on-line datas
,display pressure records with real-time
output, you can retrieve file , save the
datas for operating data analysis, records
statistic ,multi-files display in the screen,
....versatile functions for your choice.
FORMAT

Connection procedures:
1.Plug the optional accessory RS232
cable onto the DC jack port ( at the
right side of the meter)
2.Instert the D-sub 9P type connector
onto computer's Com.1 or 2 port or....
3.Start to set up RS232 software by
inserting the CD-ROM or Floppy
diskette.
4.When installing the RS232 software
,please follow the operation manual
procedure in the software package.
WARRANTY
The meter is warranted to be free from
defects in material and workmanship for
a period of one year from the date of
purchase. This warranty covers normal
operation and does not cover battery ,
misuse , abuse , alteration , tampering ,
neglect , improper maintenance , or
damage resulting from leaking batteries .
Proof of purchase is required for
warranty repairs . Warranty is void if the
meter has been opened .
17

RETURN AUTHORIZATION
CE CERTIFICATION
Authorization must be obtained from the
supplier before returning items for any
reason . When requiring a RA (Return
Authorization) , please include data
regarding the defective reason, the
meters are to be returned along with
good packing to prevent any damage in
shipment and insured against possible
damage or loss .
The meter conforms to the following
standards:
* EN 50081-1/1992: EN 55022
* EN 50082-1/1997: (EN 61000-4-2/-3/-8
,ENV 50204)
, the meter complies with the essential
protection requirements of Council
Directive 89/336/EEC on the approxi-
mation of the laws of the Member States
relating to electromagnetic compatibility.
18
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com