Test Equipment Depot AMPROBE WT-80 User manual

WT-80
pH / ORP Meter
Users Manual
• Mode d’emploi
• Bedienungshandbuch
• Manual d’Uso
• Manual de uso
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

WT-80
pH / ORP Meter
Users Manual
September 2009, Rev.1
©2009 Amprobe Test Tools.
All rights reserved. Printed in China
English

WT-80 pH / ORP Meter
1
7
6
8
10
9
2
4
3
5
1
3
5
Probe socket
Operation keys
USB port
Tripod mount hole (rear side)
pH probe temperature plug
7
9
2
4
6
LCD display
Adaptor port
Battery cover (rear side)
pH propbe with soak bottle
ORP probe with soak bottle
8
10
Meter

POWR/SET KEY: Press key to turn on and off the meter. When the meter is
on, hold down for >1 second to enter setting mode.
CAL/ESC KEY: Press to switch normal and calibration mode. While in
calibration, setting or recall mode, press to return to previous mode.
HOLD/REC KEY: Press key to freeze current reading. Press again to unlock.
Press >1 second to switch normal and recall mode. When the meter is off,
press SET+HOLD simultaneously >1 second to disable auto-sleep mode
MODE/UP KEY: Press this key to switch pH and mV. For pH probe, the valid
unit is pH and mV. For ORP probe, the valid unit is only mV. In setting or
calibration mode, press to increase value.
MEMORY/DOWN KEY: Press to record current reading. In setting or
calibration mode, press to decrease the value
MAX/MIN/ENTER KEY: Press to view the max./ min. of the memory in recall
mode. In setting or calibration mode, press to confirm and enter next step.
5
11
3
4
9
6
10
1
2
7
8
1
3
5
pH reading in unit pH or mV; ORP
reading in unit mV.
Low battery indicator
Review maximum and minimum
READY to indicate the reading is
stable
record
Freeze display
Meter is in recall mode
Total numbers of records
Real time clock
The meter is in auto temp.
compensation status
Temperature unit. ºC or ºF is selectable
Meter is in calibration mode
7
9
2
4
6
8
10
LCD
11

WT-80 pH / ORP Meter
CONTENTS
SYMBOLS...............................................................................................................2
UNPACKING AND INSPECTION ............................................................................2
INTRODUCTION .....................................................................................................3
Features ............................................................................................................3
OPERATION............................................................................................................3
Starting Up .......................................................................................................3
Auto Power Off ................................................................................................5
Setup .................................................................................................................5
Calibration (pH Probe Only) ............................................................................8
SPECIFICATIONS ....................................................................................................8
MAINTENANCE AND REPAIR ................................................................................9
Battery Replacement .......................................................................................11
USB PC Interface Capabilities ..........................................................................11
TROUBLE SHOOTING.............................................................................................11
MSDS......................................................................................................................13
Test Equipment Depot - 800.517.8431 -
99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com

2
SYMBOLS
Caution ! Refer to the explanation in this Manual
Conforms to relevant Australian standards
Complies with EU directives
Do not dispose of this pruduct as unsorted municipal waste.
Warnings and Precautions
• Please always keep the electrode glass bulb wet by using the soak bottle
to protect and store the electrode.
• Always rinse the pH electrode and reference junction in de-ionized
water before next use.
• Never touch or rub glass bulb to lengthen the electrode life.
• Recommend soak the electrode for at least 30 minutes before using,
especially if the electrode dries out between uses or after long time
unuses.
UNPACKING AND INSPECTION
Your shipping carton should include:
1 WT-80 Meter
1 pH Probe with soak bottle
1 ORP Probe with soak bottle
3 pH standard solution (4, 7, 10, non-NIST)
4 AAA battery
1 User’s Manual
If any of the items are damaged or missing, return the complete package to
the place of purchase for an exchange.

3
INTRODUCTION
Congratulations on your purchase of WT-80 pH/ORP meter. A convenient
instrument to measure water pH/ temperature and ORP value.
Features
• Automatic buffer recognition to avoid pH calibration error.
• Hold function to freeze the record.
• Max./Min. review of memorized data.
• Backlight for dark environment operation.
• Easy to view pH probe calibration data.
• USB connection for data download to a PC
• pH electrode with automatic temperature compensation.
• Auto power off to save battery power
OPERATION
Starting Up
1. Install batteries or connect with an adaptor to the power socket.
2. Connect pH or ORP electrode to the BNC port on the top of the meter.
While using pH probe, please also connect the temperature sensor plug
to the socket next to BNC.
3. Available parameters for two probes are:
pH probe: pH value, mV value & Temperature.
OPR probe: mV value
NOTE: pH unit for ORP probe is meaningless
pH Probe-pH/mV Measurement
This meter is designed to take reading with automatic or manual temperature
compensation. Automatic temperature compensation only occurs when the
temp.sensor is plugged. For manual temperature compensation, the default
setting is 25ºC / 77ºF. You can manually adjust the temperature.
Be sure to remove the pH electrode soaker bottle before measurement. To
take the readings:
1. Rinse the probe with de-ionized or distilled water before use to remove
any impurities adhering to the probe. If the electrode is dehydrated,
soak it for 30 minutes in KCl solution.

4
2. Press “POWER” key to power on. “ATC” icon appears to indicate
automatic temp. compensation while the temp. probe is plugged.
3. Dip the electrode into the sample, the electrode must be completely
immersed into the sample. Stir the probe gently to create a homogenous
sample.
4. Wait until the “READY“ icon appears. (Fig. 1)
5. To toggle between pH and mV, press “MODE” key.
ORP Probe- mV Measurement (±1999mV)
Taking ORP (Oxidation Reduction Potential, mV) measurements, the range
is -1999mV to +1999mV. Please remove the electrode soak bottle before
measurement. To take the readings
1. Rinse the probe with de-ionized or distilled water before use to remove
any impurities adhering to the probe.
2. Press “POWER” key to power on the meter and press “MODE” key to
select mV measurement.
3. Dip the electrode into the sample, the electrode must be completely
immersed into the sample. Stir the probe gently to create a homogenous
sample.
4. Wait until “READY “ icon appear. (Fig. 2). No need to take Temp.
compensation into consideration when using ORP probe.
Manual Temperature Compensation (MTC)
pH probe
Simply disconnect the Temp. sensor from meter and select the mode as pH. To
set the temperature, press “ENTER” KEY more than 1 second until ”CR“ flashes
on LCD. Press “p“or “q” key to change the temperature value and press
“ENTER” key to save and return to normal measurement mode.
ORP probe
NO ATC or MTC for ORP probe. It is not necessary to take temperature
compensation into consideration.
Hold Function
To freeze the current readings while in normal measurement mode. To hold
the readings, press “HOLD” key in measurement mode, “ HLD “appears on the
display. To release the holding value, press “HOLD” key again. (Fig.3)

5
Memory Record
The meter can store each parameter for up to 99 records. To record:
1. In any measurement or HOLD mode, press “MEM” key to save data.
2. Memory number & measured value will flash then return to
measurement mode. (Fig. 4). New data can not be saved if the memory is
full. To continuously save new memory, it is needed to clear up existing
99 memories.
Memory Recall
Recall function can review previous saved record. To recall record:
1. Press “REC” key > 2 seconds to enter recall mode. “REC“ icon will flash
on the LCD.
2. Press “p“or “q” key review memory one by one.
3. Press “MI/MX” key to view the minimum & maximum value of the
memory. (Fig. 5)
4. To exit memory recall, press “REC” key > 2 sec. to return to measurement
mode. All records are retained even the meter is powered off.
Backlight
Press any key to activate the backlight function. The backlight turns off
automatically after 10 seconds of inactivity.
Auto Power Off
This meter will shut off automatically 20 minutes of inactivity.
To disable the auto power off, pressing “ SET “ + “ HOLD” keys simultaneously
while turning on the meter until a “n” appeared on the screen and then
release keys to return to normal mode.
Setup
The advanced setup mode lets you customize your meter.
7 parameters are available in this model.
P2.0: Clear memory
P3.0: Electrode data (for pH probe only)
P4.0: PH buffer selection (for pH probe only)
P5.0: READY indication

P6.0: Temperature unit
P7.0: Real time clock
P8.0: Reset
To enter SETUP mode, hold down “SET”key >1 second while in normal
measurement mode. Press “p“or “q” to select parameters and press
“ENTER”for parameter settings. To exit any setting, press “Esc” key.
Note: P1.0 memory transmitting function is not available in this model.
P2.0 Memory Clear (CLr)
To clear the stored data, press “MODE” key to select the parameter (pH or mV)
which you want to clear before entering setup mode.
While in setup mode, press “p“ key to select memory clear function P2.0,
“CLr” icon appears on LCD (Fig.6)
Press “ENTER” key to enter P2.1.The default “ NO” icon flashes on LCD. Press
“p“ key to change and then press “ENTER” key to confirm.
NOTE: This procedure will clear 99 memories at a time. Please consider
carefully before delete.
P3.0 Electrode-for pH probe only (ELE)
To view the pH electrode data (slope & offset value) from WT-80:
Press “MODE” key to select the mode as pH before entering setting mode.
Press “p“ to select P3.0 while in setting mode, “ELE“ appears on the LCD.
Press “ENTER” key to enter P3.1, LCD displays 1of 4 available slope values
(P3.1 to P3.4). If the value is <75% or >115%, suggest to change electrode
immediately.
Press “ENTER” key to review P3.2, P3.3 & P3.4 (Fig. 7)
Press “ENTER” to enter P3.5 to view the offset value.(Fig. 8) Offset value is the
mV value of pH 7 and the default offset value is 0.0. The offset value will be
different after re-calibration. When the offset value is out of range +60mV,
strongly suggest you to replace with a new probe.
NOTE: P3.1, 3.2, P3.3 & P3.4 slope definition of buffer:
P3.1 P3.2 P3.3 P3.4
NIST 0.00~4.01 4.01~6.86 6.86~9.18 9.18~14.00
NON-NIST 0.00~4.50 4.50~7.00 7.00~9.50 9.50~14.00
Test Equipment Depot - 800.517.8431 -
99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com

7
P4.0 pH Buffer –for pH probe only (buF)
Before pH calibration, select the buffer you use. You can use NIST buffer or
non-NIST (here refer as “Custom” buffer) for calibration purpose. Correct
buffer selection can help meter to recognize the buffer and calibrate the
probe more precisely.
NIST buffer: PH1.68, 4.01, 6.86, 9.18, 12.45.
Custom buffer: 5 ranges, PH 1.00~3.00, 3.50~5.50,6.00~8.00,
8.50~10.50,11.50~13.50.
Press “p“ key to select pH buffer program P4.0 while in setting mode. “buF”
icon appears on LCD. Press “ENTER” key to enter P4.1.The default “ NIST “
icon flashes on the LCD. Press “ENTER” key to confirm or press “MODE” key to
change. (Fig.9)
The pH buffer enclosed in the standard package is non-NIST.
P5.0 Ready indication (rdy)
Use this program to activate “READY” indication. “READY” icon appears on
LCD when the measured reading is stable.
While in P5.0, press “ENTER”to go into P5.1 and press “p“or “q” to switch
Ready indicator ON or OFF and then press “ENTER” to confirm. (Fig. 10)
P6.0 Temperature Unit (U)
Use this program to select the temperature unit.
While in P6.0, press “ENTER”to go into P6.1 and press “p“or “q” to switch C
or F and then press “ENTER” to confirm. (Fig. 11)
P7.0: Real Time Clock (rtc)
In P7.0, press “ENTER” to go through P7.1 to P7.6 for date and time settings.
Y-M-D and H:M:S will show in turn and corresponding digits will be flashing
for further change. Press “p“ to increase and “q” to decrease the numbers
and press “ENTER”key to confirm every setting.
P8.0: Reset (rSt)
While in P8.0, press “ENTER”to go into P8.1. Select “n”-No or “y”-Yes with
“p“or “q” for data reset to factory default. Press “ENTER”to confirm
selection.

8
Calibration (pH Probe Only)
We recommend to operate at least a 2-point calibration. If you can only
perform a 1-point calibration, please make sure the buffer value is very closed
to the sample you are measuring and the buffer temperature must be stable
enough.
1. Select “pH” mode. Rinse the pH electrode in de-ionized water or rinse
solution. DON’T wipe the pH probe dry. Wiping the probe may cause
static and cause calibration and measurement instability.
2. Select the pH buffer (See P4.0) and pour some into a clean container. Dip
the probe into the buffer. The end of the probe must be immersed into
the buffer. Stir the probe gently to create a homogenous sample.
3. Press “CAL” key to enter calibration mode. The “CA” icon flashes on
LCD.
4. If the buffer is set as NIST in P4.0, the main display shows the auto
recognized buffer value. (Fig. 12). If this value keeps changing means the
buffer or probe need to be checked or changed.
5. If the buffer is set as CUST in P4.0, the main display shows default 2.00,
short press “HLD” key to select the buffer range you are using. Then,
press “p“or “q” key to ne adjust the value in order to meet with
buffer.
6. Wait until “Ready” icon appear on LCD. Press “ENTER” to confirm.
7. Change buffer & repeat step 5~6 to do multiple points calibration or
press “ENTER” key to end the calibration and return to normal mode.
NOTE: When in calibration, the buffer temperature must be stable enough.
SPECIFICATIONS
pH range 0.00~14.00pH
pH resolution 0.01pH
pH accuracy +0.02pH
mV range -1999mV~+1999mV
mV resolution 0.1mV(-199.9mV~+199.9mV), 1mV at others
mV accuracy +0.2mV(-199.9mV~+199.9mV), +2mV at others
ATC -5~80°C / 23ºF~176ºF
Temperature Accuracy ±0.3°C
Operation temp. 0~50°C / 32ºF~122ºF
Operation RH% 0~80%RH
Power Requirements 4pcs AAA

9
- EMC: EN61326-1.
This product complies with requirements of the following European
Community Directives: 89/ 336/ EEC (Electromagnetic Compatibility) and 73/ 23/
EEC (Low Voltage) as amended by 93/ 68/ EEC (CE Marking). However, electrical
noise or intense electromagnetic fields in the vicinity of the equipment may
disturb the measurement circuit. Measuring instruments will also respond to
unwanted signals that may be present within the measurement circuit. Users
should exercise care and take appropriate precautions to avoid misleading
results when making measurements in the presence of electronic interference.
MAINTENACE AND REPAIR
If there appears to be a malfunction during the operation of the meter, the
following steps should be performed in order to isolate the cause of the
problem.
1. Check the battery. Replace the battery immediately when the symbol
“ ” appears on the LCD.
2. Review the operating instructions for possible mistakes in operating
procedure.
Except for the replacement of the battery, repair of the meter should be
performed only by a Factory Authorized Service Center or by other qualified
instrument service personnel. The front panel and case can be cleaned with
a mild solution of detergent and water.Apply sparingly with a soft cloth and
allow to dry completely before using. Do not use aromatic hydrocarbons,
Gasoline or chlorinated solvents for cleaning.
pH Probe
Always keep pH probe wet when in storage. The probe is well protected by a
plastic bottle with soak solution in it. To use the probes, rotate the bottle and
remove the bottle away from the probe.
pH probe can be stored in a 3M KCL solution. Never use distilled water for
storage. Always rinse the pH electrode in de-ionized water before next use.
Never touch or rub glass bulb for lasting pH electrode life.
ORP Probe
Preparation:Remove the soaking bottle. Soak the electrode into distilled water
and rinse, then, take out and make dry (Do not rub sensing element forcibly).
Now, the electrode is ready for use.

10
Test the electrode:
Connect ORP electrode to meter. Immerse electrode in pH7.00 buffer solution
with saturated quinhydrone. After stirring, mV reading (E1) should be
86±15mV.
Rinse electrode with distilled water, then set it in buffer solution of pH4.01
with saturated quinhydrone. After stabilizing, record mV meter reading (E2).
The difference between E1 and E2 should be around 165mV.
Storage:
Rinse the electrode with distilled water during the interval of each use. Keep
ORP electrode wet in the provided soaking bottle which is filled with soaking
solution.
ORP electrode cleaning:
If sensing element got contaminated, it will result in slow response and
inaccurate reading. Clean it as following:
If contamination is a mineral matter, put sensing element in HCL solution 0.1N
for 10 minutes and then rinse it with distilled water.
If the contamination is oil or grease coating, clean sensing element with
detergent and rinse with distilled water.
After above treatments, put electrode in saturated buffer pH4.01 for 15min
and then rinse with distilled water.
NOTE: After cleaning, soak the electrode in solution for at least 8 hours.
Electrode response time and accuracy:
Sensing element of ORP electrode is made of high purity metal, it truly reflects
the tested solution’s ability of oxidation-reduction. However, slow response
time and inaccurate reading may occur from time to time. The root cause is an
oxidation-reduction coating was formed outside the electrode after long time
using or storage. A simple way to solve this problem is to clean the probe.
Moreover, while the concentration of oxidation-reduction matter is low and
ion exchange rate is slow, they may also cause slow response and inaccurate
reading. Under this condition, it may take 8-24 hours to get a reliable and
correct reading.

Battery Replacement
1. Turn off the meter and open the battery cover.
2. Replace the old batteries with four new AAA batteries.
USB PC Interface Capabilities
The USB cable and software are required to transfer data to a pc. The USB
port is located on the right side of the instrument. The USB cable is not
included. it can be purchased separately as an optional accessory.
The protocol is:
Format: pxx.xxpH:mxx.xxmV:Txxx.xC(F) @2007-04-18 18:48:48LRCCRLF
Baud rate: 9600 bit/sec
Data bit: 8
Stop bit: 1
Parity: none
TROUBLESHOOTING
Power on but no display
• Make sure you press power key >0.3second.
• Check the battery conditions and replace if necessary
• Move batteries away for one minute and then re-install.
Display disappear
• Check whether the low battery icon is appeared before the display is off.
If yes, replace with new batteries.
Unstable reading
• Stir the solution to make homogeneous status and make sure the sensor
is completely immersed in solution.
• Make sure the measurement is processed in container.
• Clean or re-calibrate or replace with a new probe
• Move to another room and try again , it is supposed that the unstable
reading is caused by strong RF interference field.
Test Equipment Depot - 800.517.8431 -
99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com

12
The reading is not changed
• If the status is in “HOLD”, release the status.
• If the measurement is in MTC, input temperature value.
Slow response
• Clean and re-calibrate the probe.
• Replace with a new probe.
Wrong real time
• The wrong real time display will not affect the measurement. Contact
the distributor to purchase battery and acquire replacement procedures.
Error code
E02 Reading is under the lower limit
E03 Reading is over the upper limit
E04 The original data error result in this error
E12 Factory calibration data error
Solution: Re-start meter might solve this error
E13 Slope or offset value of pH probe is out of the range
E31 Measuring circuit failure
Solution: Re-start meter might solve this error
E32 Memory IC failure

13
MATERIAL SAFETY DATA SHEET OF SOAK SOLUTION
SECTION I - IDENTITY INFORMATION
Ingredient: KCL
Chemical Name: Potassium monochloride
Cas No.: 7447-40-7
Manufacturer: Ajax Finechem (http://www.ajaxnechem.com/)
Phone: [phone]
Date Prepared: 2006-04-24
SECTION II -PHYSICAL/CHEMICAL CHARACTERISTIC
Boiling Point: Not available
Melting Point: 773 degree C / 1423ºF
Vapor Pressure: Not available.
Water Solubility: Soluble
Appearance / Odor: Colourless or white crystals, odorless
SECTION III - HEALTH HAZARD DATA
Route of Entry: Inhalation, Ingestion, skin & eye absorption
Health Hazards: Inhalation may cause respiratory tract irritation. Irritative to
eyes and skin. Harmful if swallowed.
SECTION IV: EMERGENCY & FIRST AID MEASURES
Eyes: Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lift the upper and lower eyelids. Get medical aid.
Skin: Remove contaminated clothing and shoes. Flush skin with plenty of
water for at least 15 minutes. Get medical aid.
Inhalation: Remove from exposure to fresh air immediately. If not breathing,
give artificial respiration. If breathing is difficult, give oxygen. Get medical aid.
Ingestion: Do not induce vomiting. Get medical aid if irritation or symptoms
occur.
SECTION V: FIRE FIGHTING MEASURES
Flash Point: not flammable

14
Special Fire Fighting Procedures: Wear self-contained breathing apparatus and
protective clothing to prevent contact with skin and clothing.
Unusual Fire & Explosion Hazards: Not combustible
SECTION VI - EXPOSURE CONTROLS, PERSONAL PROTECTION
Wear appropriate protective eyeglasses or chemical safety goggles. Wear
appropriate protective gloves to prevent skin exposure. Wear appropriate
protective clothing to minimize contact with skin. Use NIOSH/MSHA or
European standard EN149 approved respirator if exposure limits are exceeded
or if irritation or other symptoms are experienced.
SECTION VII - HANDLING AND STORAGE
Handling: Avoid generating dust. Use smallest possible amounts in designated
areas with adequate ventilation. Have emergency equipment (for fires, spills,
leaks, etc.) readily available. Label containers. Keep containers closed when not
in use. Wear appropriate protective equipment to prevent inhalation, skin and
eye contact. Ensure a high level of personal hygiene is maintained when using
this product. That is; always wash hands before eating, drinking, smoking or
using the toilet.
Storage: Store in a cool, dry, well-ventilated area, out of direct sunlight and
moisture. Store in labelled containers. Keep containers tightly closed. Store
away from bases, water and other incompatible materials. Have appropriate
fire extinguishers available in and near the storage area.
SECTION VIII - REACTIVITY DATA
Stability: Stable under normal temperature and pressures.
Hazardous Polymerization: Will not occur
Materials to Avoid: None known
DISCLAIMER
The above information is transferred to this format by Amprobe from the
Material Safety Data Sheet supplied by the manufacturer identified in Section
I. If you have any questions related to the material provided herein, contact
the manufacturer directly at the phone number given in Section I.
Amprobe does not, in any way, represent itself as an expert in the chemical
described in this MSDS and assume in liability for any incomplete or inaccurate
information contained herein.”

15
MATERIAL SAFETY DATA SHEET OF pH4 BUFFER
SECTION I - IDENTITY INFORMATION
Ingredient: Potassium hydrogen phthalate (C8H5O4K)
Chemical Name: Potassium hydrogen phthalate
Cas No.: 877-24-7
Manufacturer: Ajax Finechem (http://www.ajaxnechem.com/)
Phone: [phone]
Date Prepared: 2005-10-14
SECTION II -PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point: Not available
Melting Point: 295-300 degree C / 563-572 ºF
Vapor Pressure: Not available.
Water Solubility: Soluble
Appearance / Odor: white crystalline powder, odorless
SECTION III - HEALTH HAZARD DATA
Route of Entry: Inhalation, Ingestion, skin & eye absorption
Health Hazards: Inhalation may cause respiratory tract irritation. Irritative to
eyes and skin. Harmful if swallowed.
SECTION IV: EMERGENCY & FIRST AID MEASURES
Eyes: “Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lift the upper and lower eyelids. Get medical aid.
Skin: Remove contaminated clothing and shoes. Flush skin with plenty of
water for at least 15 minutes. Get medical aid.
Inhalation: Remove from exposure to fresh air immediately. If not breathing,
give artificial respiration. If breathing is difficult, give oxygen. Get medical aid.
Ingestion: Do not induce vomiting. Get medical aid if irritation or symptoms
occur.

SECTION V: FIRE FIGHTING MEASURES
Flash Point: not flammable
Special Fire Fighting Procedures: Wear self-contained breathing apparatus and
protective clothing to prevent contact with skin and clothing.
Unusual Fire & Explosion Hazards: Not combustible
SECTION VI - EXPOSURE CONTROLS, PERSONAL PROTECTION
Wear appropriate protective eyeglasses or chemical safety goggles. Wear
appropriate protective gloves to prevent skin exposure. Wear appropriate
protective clothing to minimize contact with skin. Use NIOSH/MSHA or
European standard EN149 approved respirator if exposure limits are exceeded
or if irritation or other symptoms are experienced.
SECTION VII - HANDLING AND STORAGE
Handling: Avoid generating dust. Use smallest possible amounts in designated
areas with adequate ventilation. Have emergency equipment (for fires, spills,
leaks, etc.) readily available. Label containers. Keep containers closed when not
in use. Wear appropriate protective equipment to prevent inhalation, skin and
eye contact. Ensure a high level of personal hygiene is maintained when using
this product. That is; always wash hands before eating, drinking, smoking or
using the toilet.
Storage: Store in a cool, dry, well-ventilated area, out of direct sunlight and
moisture. Store in labelled containers. Keep containers tightly closed. Store
away from bases, water and other incompatible materials. Have appropriate
fire extinguishers available in and near the storage area.
SECTION VIII - REACTIVITY DATA
Stability: Stable under normal temperature and pressures.
Hazardous Polymerization: Will not occur
Materials to Avoid: Strong oxidizing agents, nitric acid.
DISCLAIMER
The above information is transferred to this format by Amprobe from the
Material Safety Data Sheet supplied by the manufacturer identified in Section
I. If you have any questions related to the material provided herein, contact
the manufacturer directly at the phone number given in Section I.
Amprobe does not, in any way, represent itself as an expert in the chemical
described in this MSDS and assume in liability for any incomplete or inaccurate
information contained herein.
Test Equipment Depot - 800.517.8431 -
99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com