TEUCER LR-4RGB Manual

The LR-4RGB/4RGBW rremote enables one to control up to
4 zones of RGB LED strips. Featuring a touch colour wheel
which oers smooth and connuous colour changing op-
ons, enabling creaon of colourful stac and dynamic ef-
fects.
Product ImageProduct Descripon
Technical Specicaon
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Controller
Order Code LR-4RGB/4RGBW
Type RF Remote
Input Voltage 3VDC
Operaon Frequency 2.4GHz
Dimension 58.5x107x9mm (WxLxH)
Power baery CR2032
Receiver
Order Code R3C
Type RF receiver
Input Voltage 12-24VDC
Current 3x4A
Output 144-288)W
Note Constant voltage
Dimension 33x97x18mm (WxLxH)
• Easy control of RGB LED strips.
• Single zone, two, three and four zone control.
• 2.4GHz wireless technology, remote distance of up to
30m.
• Operates with an LED indicator light for ease of use.
• Each remote can control one or more receivers.
• Control each zone separately or simultaneously
• PWM dimming enables icker-less dimming
Features
RF technology allows for greater exibility when it comes to
controlling simple or complex lighng installaons without
the need of addional cabling.
There are some limitaons where installaons have the
receivers enclosed in electrical boxes or hidden away in a
ceiling , reducing the RF signal strength and therefore the
communicaon range.
In order to overcome these RF Signal restricons we sug-
gest the following when synchronising our RF controllers
and receivers:
• Keep the distance within 10 meters from the controller
• to the receiver. The remote can operate up to 30mtrs if
signal is uninterrupted by obstacles.
• When expanding your lighng, always try and use a
signal repeater (PR-RGB), where possible.
• If your installaon requires several RF receivers, ensure
the “master” receiver is posioned in the middle.
Recommendaon
LR-4RGB/4RGBW and R3C
4 zones RF controller and 3 zones receiver for RGB LED strip

Receiver wiring diagram
Controller layout
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
R3C
RGB LED strip
Power supply
+
1234

colour wheel 
Decrease brightness Increase brightness
Play mode
Zones

White
LR-4RGB/4RGBW and R3C
4 zones RF controller and receiver for RGB LED strip

Synchronising the remote to receiver
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
1) Ensure the receiver has power. Press the match buon on the receiver. Indicator will start ashing.
4) To restore to factory default sengs and delete the allocated
controller, press and hold the match buon longer than 5 seconds.
2) Choose the required zone on the remote to allocate the receiver within 5 seconds aer pressing the
match buon. The indicator will stop ashing, and the controller will be synchronised.
Match bu�on
Indicator
R3C
Press the zone
you wish to allocate
1234
Troubleshoot
Problem Cause Correcve
No light • No power.
• Wrong connecon or unsecure connec-
on.
• Check the power.
• Check the connecon.
Wrong Colour • Wrong connecon of RGB/W wires. • Re trace and reconnect
RGB/W wires.
Uneven intensity be-
tween front and rear of
the strip, with voltage
drop
• Output cable is too long.
• Cable diameter is too small.
• Overload beyond driver capability.
• Overload beyond receiver capability.
• Reduce cable or loop sup-
ply.
• Change to a thicker cable.
• Replace with a suitable
higher power driver.
• Add a power repeater.
No response
from the remote
• The baery has no power.
• Beyond controllable distance.
• The controller isn’t synchronised with the
remote.
• Replace baery.
• Reduce remote to receiver
distance.
• Re-sync the remote.
3) Repeat the process to allocate zones for all receivers.
LR-4RGB/4RGBW and R3C
4 zones RF controller and receiver for RGB LED strip

Teucer (UK) Ltd
Head oce
Bedford House, Fulham Green, Fulham High Street,
London, SW6 3JW, UK
Tel: [phone]
Fax: [phone]
www.teucerled.co.uk
[e-mail]
Logiscs Centre
Trident Court,
1 Oakcro Road,
Chessington,
Surrey, KT9 1BD, London, UK
Tel: [phone], extension: 401
[e-mail]
Controlling your LED strip
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Warranty
• Products must be installed and serviced by qualied
electrician.
• Please ensure the receiver is mounted in a water proof
enclosure if installed in an outdoor environment,
avoiding metallic enclosures.
• Always ensure products are mounted in areas with
adequate venlaon to avoid overheang.
• Please ensure outputs of any power suppliers used in
conjucon with this product comply with its working
voltage.
• Never install product whilst connected to power and
double check connecons before switching on to
avoid short circuits.
Safety
Should this product fail during the 3 year warranty
period it will be replaced free of charge, subject to the
correct installaon of the original product in accordance
with applicable and appropriate electrical codes and
instrucons provided by Teucer, as well as subsequent
return of the faulty unit. Teucer does not accept
responsibility for any installaon costs associated with
the replacement of this product and Teucer reserves the
right to alter specicaons without prior noce. Teucer
can oer 5 year warranty upon request. For further
informaon, please see our Terms and Condions.
www.teucerled.co.uk/terms-and-condions/
• Choose the zone(s) you
wish to control.
• To change the colour, use
the touch sensive colour
wheel.
• To change the brightness,
press the buons for
increasing / decreasing
brightness.
1234
Touch sensi�ve
colour wheel ON/OFF
Decrease brightness Increase brightness
Play mode
Zones
Scene save / recall
White
LR-4RGB/4RGBW and R3C
4 zones RF controller and receiver for RGB LED strip
• There are several dynamic modes, press the play mode buon to browse through modes. To
choose the mode, press and hold play mode for 2seconds.
• There are 10 speeds for the play modes. Press the speed buon to browse through the speed
levels.
• Press and hold the speed buon to go to the highest speed level.
• To save your setup, press and hold scene buons.
• To recall saved secene, press scene buon.