TEUCER WP-4RGBWN Instruction manual

The WP-4RGBW wall panel enables control of 1 to 4 zones
of RGBW LED strip. Featuring a simple to use back lit touch
control slider for easy colour adjustment .
Product ImageProduct Descripon
Technical Specicaon
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Controller
Order Code WP-4RGBWN
Type RF and DMX wall panel
Input Voltage AC85-265V
Operaon Frequency 2.4GHz
Dimension 86x86x36.5mm (WxLxH)
• Enables control via DMX (DMX decoder required for
DMX) or wirelessly via RF
• Supports single zone independent control or mulple
zone synchronous control.
• Ultra-sensive backlit high strength glass touch panel.
• Smooth and accurate colour adjustment via a touch
colour slider.
• Independent brightness adjustment of each RGBW
channel to achievea vast pallet of colours.
• Built in 30 oponal change modes with adjustable
speed and brightness.
Features
RF technology allows for greater exibility when it comes to
controlling simple or complex lighng installaons without
the need of addional cabling.
There are some limitaons where installaons have the
receivers enclosed in electrical boxes or hidden away in a
ceiling , reducing the RF signal strength and therefore the
communicaon range.
In order to overcome these RF Signal restricons we sug-
gest the following when synchronising our RF controllers
and receivers:
• Keep the distance within 10 meters from the control-
ler to the receiver. The remote can operate up to 30
meters if signal is uninterrupted by obstacles.
• When expanding your lighng, always try and use a
signal repeater (PR-RGB), where possible.
• If your installaon requires several RF receivers, ensure
the “master” receiver is posioned in the middle.
Recommendaon
Receiver
Order Code R4C
Type RF receiver
Input Voltage 12-36VDC
Current 4x5A
Output 4x(60-180)W
Note Constant voltage
Dimension 45x175x27mm (WxLxH)
WP-4RGBWN and R4C
4 zones RF controller with R4C receiver for RGBW LED strip

Receiver wiring diagram
Controller layout
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
ON/OFF
Brightness / speed
Zones / Scenes Play mode
RGB colour slide
White
R4C
RGBW LED strip
Power supply
+
R
G
B
W
WP-4RGBWN and R4C
4 zones RF controller with R4C receiver for RGBW LED strip
Dip switch sengs
1 23
ON
OFF
ON
RGBW Dipswitch seng for 4 Scenes
Dipswitch no 1: UP (ON)
Dipswitch no 2: DOWN (OFF)
Dipswitch no 3: RF - UP (ON)
Cauon: before power ON, you must conrm the dip switch selecon.
RGBW Dipswitch seng for 4 Zones
Dipswitch no 1: UP (ON)
Dipswitch no 2: UP (ON)
Dipswitch no 3: RF - UP(ON)
1 23
ONON ON

Synchronising the remote to receiver
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Press the zone
you wish to allocate
Troubleshoot
Problem Cause Correcve
No light • No power.
• Wrong connecon or unsecure connec-
on.
• Check the power.
• Check the connecon.
Wrong Colour • Wrong connecon of RGB/W wires. • Retrace and reconnect RG-
B/W wires.
Uneven intensity be-
tween front and rear of
the strip, with voltage
drop
• Output cable is too long.
• Cable diameter is too small.
• Overload beyond driver capability.
• Overload beyond receiver capability.
• Reduce cable or loop sup-
ply.
• Change to a thicker cable.
• Replace with a suitable
higher power driver.
• Add a power repeater.
No response
from the remote
• The wall panel has no power.
• Beyond controllable distance.
• The controller isn’t synchronised with the
remote.
• Check the incoming supply
to the wall panel
• Reduce remote to receiver
distance.
• Re-sync the remote.
1) Ensure the receiver has power. Press the match buon on the receiver. Indicator will start ashing.
4) To restore to factory default sengs and delete the
allocated controller, press and hold the match buon
longer than 5 seconds.
2) Choose the zone on the remote to allocate the receiver within 5 seconds aer pressing the match buon.
The indicator will stop ashing, and the controller will be synchronised.
Match bu�on
R4C
3) Repeat the process with allocang zones for all
receivers.
WP-4RGBWN and R4C
4 zones RF controller with R4C receiver for RGBW LED strip

Teucer (UK) Ltd
Head oce
Bedford House, Fulham Green, Fulham High Street,
London, SW6 3JW, UK
Tel: [phone]
Fax: [phone]
www.teucerled.co.uk
[e-mail]
Logiscs Centre
Trident Court,
1 Oakcro Road,
Chessington,
Surrey, KT9 1BD, London, UK
Tel: [phone], extension: 401
[e-mail]
Controlling your LED strip
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Warranty
• Products must be installed and serviced by qualied
electrician.
• Please ensure the receiver is mounted in a water proof
enclosure if installed in an outdoor environment,
avoiding metallic enclosures.
• Always ensure products are mounted in areas with
adequate venlaon to avoid overheang.
• Please ensure outputs of any power suppliers used in
conjucon with this product comply with its working
voltage.
• Never install product whilst connected to power and
double check connecons before switching on to
avoid short circuits.
Safety
Should this product fail during the 3 year warranty
period it will be replaced free of charge, subject to the
correct installaon of the original product in accordance
with applicable and appropriate electrical codes and
instrucons provided by Teucer, as well as subsequent
return of the faulty unit. Teucer does not accept
responsibility for any installaon costs associated with
the replacement of this product and Teucer reserves the
right to alter specicaons without prior noce. Teucer
can oer 5 year warranty upon request. For further
informaon, please see our Terms and Condions.
www.teucerled.co.uk/terms-and-condions/
ON/OFF
Brightness / speed
Zones / Scenes Play mode
RGB colour slide
White
• There are 30 dynamic modes, press the play mode buon to browse thorugh modes. To choose the mode,
press and hold play mode for 2seconds.
• There are 10 speeds for the play modes. Press the speed buon to browse through the speed levels.
• Press and hold the speed buon to go to the highest speed level.
• To save your favourite setup, press and hold scene buons.
• To recall saved setup, press scene buon.
• You can save up to 4 scenes.
• To adjust the colour, touch the RGB colour slider.
• To change the brightness, press the brightness
buon.
• On/O: For single zone: Turn ON/OFF strips.
• For 4 Zone: Short press turn ON/OFF current
zone light, long press 2s turn OFF all zones strips.
• Mode: Short press to run next mode, long press
2s runs mode-cycle.
• W: Short press to turn ON/OFF W channel,
• Long press 1-5s for connuous 256 levels adjust-
ment of the white channel brightness.
• Zone: Choose the zone(s) you wish to control.
• Zone / Scene: When used as 4 scene: Short press-
to run the scene, long press 2s to save.
WP-4RGBWN and R4C
4 zones RF controller with R4C receiver for RGBW LED strip