TEUCER LR-RGB/RGBW User manual

The LR-RGB/RGBW remote enables control of single zone of
RGBW LED strip. Featuring a touch colour wheel, the LR-
RGB/RGBW controller enables the user to adjust the output
colour seamlessly via the scroll wheel.
Product ImageProduct Descripon
Technical Specicaon
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Controller
Order Code LR-RGB/RGBW
Type RF Remote
Input Voltage 3VDC
Operaon Frequency 2.4GHz
Dimension 58.5x107x9mm (WxLxH)
Power baery CR2032
Receiver
Order Code R4C
Type RF receiver
Input Voltage 12-36VDC
Current 3x4A
Output 4x(60-180)W
Note Constant voltage
Dimension 45x175x27mm (WxLxH)
• Built in play mode to create dynamic eects.
• PWM dimming enables icker-less dimming.
• Works with signal repeaters to expand output.
• 2.4GHz wireless technology, enabling remote distance
of up to 30m.
• LED indicator light for ease of use.
• Each remote can control one or more receivers.
• Control each zone separately or simultaneously.
• Dimming range: 0-100%.
Features
RF technology allows for greater exibility when it comes to
controlling simple or complex lighng installaons without
the need of addional cabling.
There are some limitaons where installaons have the
receivers enclosed in electrical boxes or hidden away in a
ceiling , reducing the RF signal strength and therefore the
communicaon range.
In order to overcome these RF Signal restricons we sug-
gest the following when synchronising our RF controllers
and receivers:
• Keep the distance within 10 meters from the control-
ler to the receiver. The remote can operate up to 30
meters if signal is uninterrupted by obstacles.
• When expanding your lighng, always try and use a
signal repeater (PR-RGB), where possible.
• If your installaon requires several RF receivers, ensure
the “master” receiver is posioned in the middle.
Recommendaon
LR-RGB/RGBW and R4C
1 zone RF controller and receiver for RGBW LED strip

Receiver wiring diagram
Controller layout
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
R4C
RGBW LED strip
Power supply
+
R
G
B
W

colour wheel 
Decrease brightness Increase brightness
Play mode


Play mode speed
LR-RGB/RGBW and R4C
1 zone RF controller and receiver for RGBW LED strip

Synchronising the remote to receiver
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
1) Ensure the receiver has power. Press the match buon on the receiver. Indicator will start ashing.
3) To restore to factory default sengs and delete the allocated con-
troller, press and hold the match buon longer than 5 seconds.
2) Press any buon on the remote to allocate the receiver within 5 seconds aer pressing the match buon.
The indicator will stop ashing, and the controller will be synchronised.
Match bu�on
R4C
Press any bu�on to
allocate
the receiver
Troubleshoot
Problem Cause Correcve
No light • No power.
• Wrong connecon or unsecure connec-
on.
• Check the power.
• Check the connecon.
Wrong Colour • Wrong connecon of RGBW wires. • Re trace and reconnect
RGBW wires.
Uneven intensity be-
tween front and rear of
the strip, with voltage
drop
• Output cable is too long.
• Cable diameter is too small.
• Overload beyond driver capability.
• Overload beyond receiver capability.
• Reduce cable or loop supply.
• Change to a thicker cable.
• Replace with a suitable high-
er power driver.
• Add a power repeater.
No response
from the remote
• The baery has no power.
• Beyond controllable distance.
• The controller isn’t synchronised with the
remote.
• Replace baery.
• Reduce remote to receiver
distance.
• Re-sync the remote.
LR-RGB/RGBW and R4C
1 zone RF controller and receiver for RGBW LED strip

Teucer (UK) Ltd
Head oce
Bedford House, Fulham Green, Fulham High Street,
London, SW6 3JW, UK
Tel: [phone]
Fax: [phone]
www.teucerled.co.uk
[e-mail]
Logiscs Centre
Trident Court,
1 Oakcro Road,
Chessington,
Surrey, KT9 1BD, London, UK
Tel: [phone], extension: 401
[e-mail]
Controlling your LED strip
Brighter for longer
CONTROLLER AND RECEIVER
www.teucerled.co.uk
Warranty
• Products must be installed and serviced by qualied
electrician.
• Please ensure the receiver is mounted in a water proof
enclosure if installed in an outdoor environment,
avoiding metallic enclosures.
• Always ensure products are mounted in areas with
adequate venlaon to avoid overheang.
• Please ensure outputs of any power suppliers used in
conjucon with this product comply with its working
voltage.
• Never install product whilst connected to power and
double check connecons before switching on to
avoid short circuits.
Safety
Should this product fail during the 3 year warranty
period it will be replaced free of charge, subject to the
correct installaon of the original product in accordance
with applicable and appropriate electrical codes and
instrucons provided by Teucer, as well as subsequent
return of the faulty unit. Teucer does not accept
responsibility for any installaon costs associated with
the replacement of this product and Teucer reserves the
right to alter specicaons without prior noce. Teucer
can oer 5 year warranty upon request. For further
informaon, please see our Terms and Condions.
www.teucerled.co.uk/terms-and-condions/

colour wheel ON/OFF
Decrease brightness Increase brightness
Play mode


Play mode speed
LR-RGB/RGBW and R4C
1 zone RF controller and receiver for RGBW LED strip
• To change colour, use the
colour wheel.
• To alter the brightness,-
press the colour buons
(RGBW) then press the
increase / decrease
brightness buons. The
brightness will change to
the desired level.
• There are several dynamic modes, press the play mode buon to browse thorugh modes. To
choose the mode, press and hold play mode for 2seconds.
• There are 10 speeds for the play modes. Press the speed buon to browse through the speed
levels.
• Press and hold the speed buon to go tho the highest speed level.
• To save a favourite colour, press and hold scene buons.
• To recall saved setup, press scene buon.