Texas Instruments DEM-DSD1796 User manual

DEM-DSD1796/PCM1795/PCM1796/PCM1798
DSD1796/PCM1795/PCM1796/PCM1798 Evaluation Module
User's Guide
Literature Number: SLEU057ASeptember 2004 – Revised May 2009

2 SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

Contents
Preface ............................................................................................................................... 5
1 Description ................................................................................................................ 71.1 Functional Block Diagram .................................................................................................. 81.2 EVM Features ................................................................................................................ 81.3 System Requirements ....................................................................................................... 91.4 Electrostatic Discharge Warning ........................................................................................... 91.5 Function Control for DAI Interface Format ............................................................................... 91.6 Reset Operation .............................................................................................................. 91.7 SW006 Operation Control for DAC ...................................................................................... 101.8 Jumper Connection ........................................................................................................ 101.9 Demonstration Software ................................................................................................... 10
2 Schematics, PCB Layout, and Bill of Materials ............................................................. 112.1 DEM-DAI/ASDAC Printed Circuit Board Layout ........................................................................ 122.2 DEM-AS/CDAC Printed Circuit Board Layout .......................................................................... 152.3 DEM-DAI/ASDAC Schematics ............................................................................................ 172.4 DEM-AS/CDAC Schematics .............................................................................................. 192.5 Component Lists ........................................................................................................... 202.5.1 DEM-AS/CDAC_96/98 Parts List................................................................................ 202.5.2 DEM-DAI/ASDAC_96/98 Parts List ............................................................................. 20
Revision History ................................................................................................................. 22
Important Notices ............................................................................................................... 23
SLEU057A – September 2004 – Revised May 2009 Contents 3Submit Documentation Feedback

www.ti.com
List of Figures
1-1 DEM-DSD1796/PCM1795/PCM1796/PCM1798 Block Diagram ...................................................... 82-1 DEM-DAI/ASDAC Silkscreen ............................................................................................. 122-2 DEM-DAI/ASDAC (Top View) ............................................................................................ 132-3 DEM-DAI/ASDAC (Bottom View)......................................................................................... 142-4 DEM-AS/CDAC Silkscreen ................................................................................................ 152-5 DEM-AS/CDAC (Top View) ............................................................................................... 152-6 DEM-AS/CDAC (Bottom View) ........................................................................................... 162-7 DEM-DAI/ASDAC Analog Section (Sockets for Daughterboard and Low-Pass Filter) ............................ 172-8 DEM-DAI/ASDAC Connector and Regulator ........................................................................... 172-9 DEM-DAI/ASDAC Digital Section (Digital Audio Interface) ........................................................... 182-10 DEM-AS/CDAC ............................................................................................................. 19
List of Tables
1-1 Digital Audio Receiver Configuration ...................................................................................... 91-2 SW006 Options ............................................................................................................. 102-1 Bill of Materials ............................................................................................................. 202-2 Bill of Materials ............................................................................................................. 20
4List of Figures SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

PrefaceSLEU057A – September 2004 – Revised May 2009
Read This First
About This Manual
This document provides the information needed to set up and operate theDEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM evaluation module, a test platform for the 24-bit,192-kHz, sampling stereo DSD1796 ,PCM1795 ,PCM1796 , and PCM1798 audio digital-to-analogconverters (DACs). For a more detailed description of these devices, refer to the specific device productdata sheet available from the Texas Instruments web site at http://www.ti.com .
How to Use This ManualThroughout this document, the abbreviation EVM and the term evaluation module are synonymous withthe DEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM. Unless specifically noted, the informationpresented in this manual applies to the DSD1796, PCM1795, PCM1796, and PCM1798 audio stereoDACs.
Chapter 1 describes the hardware setup guide for the EVM, including the necessary information requiredto configure the EVM switches and jumpers for product evaluation. This chapter also explains how to usethe software provided with the DEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM for controlling theDAC.
Chapter 2 includes the EVM electrical schematics, printed circuit board (PCB) layouts, and the bills ofmaterial for both the DEM-DSD1796/PCM1795/PCM1796/PCM1798, the DEM-AS/CDAC, and theDEM-DAI/ASDAC.
Information About Cautions and WarningsThis document contains caution statements.
CAUTION
This is an example of a caution statement. A caution statement describes asituation that could potentially damage your software or equipment.
The information in a caution or a warning is provided for your protection. Please read each caution andwarning carefully.
If You Need Assistance
If you have questions regarding either the use of this evaluation module or the information contained in theaccompanying documentation, please contact the Texas Instruments Product Information Center at (972)644–5580 or visit the TI web site at www.ti.com .
FCC Warning
This equipment is intended for use in a laboratory test environment only. It generates, uses, and canradiate radio frequency energy and has not been tested for compliance with the limits of computingdevices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonableprotection against radio frequency interference. Operation of this equipment in other environments maycause interference with radio communications, in which case the user at his own expense is required totake whatever measures may be required to correct this interference.
Microsoft, Windows are registered trademarks of Microsoft Corporation.I
2
S is a trademark of NXP Semiconductors.TOSLINK is a trademark of Toshiba Corporation.All other trademarks are the property of their respective owners.
SLEU057A – September 2004 – Revised May 2009 Read This First 5Submit Documentation Feedback

Trademarks www.ti.com
Trademarks
All trademarks are the property of their respective owners.
Read This First6 SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

Chapter 1SLEU057A – September 2004 – Revised May 2009
Description
The DEM-DSD1796/PCM1795/PCM1796/PCM1798 is an evaluation fixture for the DSD1796/PCM1795/PCM1796/PCM1798 series of 24-bit, 192-kHz sampling stereo DACs. This EVM provides all necessaryconnectors and circuitry for interfacing to audio test systems and commercial audio equipment.
Topic .................................................................................................. Page
1.1 Functional Block Diagram ............................................................ 81.2 EVM Features ............................................................................. 81.3 System Requirements ................................................................. 91.4 Electrostatic Discharge Warning .................................................. 91.5 Function Control for DAI Interface Format ..................................... 91.6 Reset Operation.......................................................................... 91.7 SW006 Operation Control for DAC .............................................. 101.8 Jumper Connection ................................................................... 101.9 Demonstration Software ............................................................ 10
SLEU057A – September 2004 – Revised May 2009 Description 7Submit Documentation Feedback

1.1 Functional Block Diagram
CN003
Serial
Connector
I/V
5534a
I/V
5534a
I/V
5534a
I/V
5534a
BAL Amp
5534a
BAL Amp
5534a
LchOUT
(4.5 V )
RMS
RchOUT
(4.5 V )
RMS
DAI
CS8414
SW001 003
Mode Control
-
S/PDIF IN
OPT
Coax
DSDS1796
PCM1795
PCM1796
PCM1798
DEM-AS/CDAC Daughter Card
3.3-V
Regulator
+VCC
(5 V)
±
±
AVCC
( 15 V)
1.2 EVM Features
Functional Block Diagram www.ti.com
Figure 1-1 illustrates the functional block diagram of the DEM-DSD1796/PCM1795/PCM1796/PCM1798EVM.
Figure 1-1. DEM-DSD1796/PCM1795/PCM1796/PCM1798 Block Diagram
The DEM-DSD1796/PCM1795/PCM1796/PCM1798 series of stereo DACs consist of a DAI (S/PDIF)section that uses a DSD1796/PCM1795/PCM1796/PCM1798 DAC section, a differential current/voltage(I/V) section, and a balanced amplifier with a post-low-pass filter (LPF) section.
The DEM-DSD1796/PCM1795/PCM1796/PCM1798 requires a 5-V digital power supply for its digitalcircuits, a 5-V analog power supply for the device itself, and a ±15-V analog power supply for thebalanced amplifier circuits.
The DAI section has both coaxial and optical inputs that are switch-selectable and capable of handlingsampling rates up to 96 kHz.
The DSD1796/PCM1795/PCM1796/PCM1798 accepts PCM audio data input at a sampling rate up to 192kHz, or a 64-f
S
DSD signal input, as determined by functional control settings and jumper connections onthe board.
This evaluation fixture uses the DEM-DSD1796/PCM1795/PCM1796/PCM1798 demonstration board anddemonstration software for functional evaluation and operational control of theDSD1796/PCM1795/PCM1796/PCM1798 DAC device.
Description 8 SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

1.3 System Requirements
1.4 Electrostatic Discharge Warning
1.5 Function Control for DAI Interface Format
1.6 Reset Operation
www.ti.com System Requirements
The DEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM has the following requirements:• ± 15-V analog power supply at AVCC+, AVCC–, and GND•5-V DAC power supply at VCC and GND•S/PDIF input (sampling rate f
S
is up to 96 kHz) connected at the coaxial or optical connector•RCA analog output connected at CN103 (Lch) and CN104 (Rch); analog full-scale output level is 4.5V
RMS
.•PC connected to printer connector CN003 for demonstration software operation (if necessary)•Appropriate test module:– DEM-PCM1795: for PCM1795– DEM-PCM1796: for PCM1796– DEM-DSD1796: for DSD1796– DEM-PCM1798: for PCM1798
Many of the components on the DEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM are susceptible todamage by electrostatic discharge (ESD). Customers are advised to observe proper ESD handlingprecautions when unpacking and handling the EVM, including the use of a grounded wrist strap at anapproved ESD workstation.
CAUTION
Failure to observe ESD handling procedures may result in damage to EVMcomponents.
SW001, SW002, and SW003 are switches for controlling the audio interface format of the DAI receiverCS8414. The default audio interface format of the DSD1796/PCM1795/PCM1796/PCM1798 is I
2
S™format. Table 1-1 lists the digital audio receiver configuration parameters.
Table 1-1. Digital Audio Receiver Configuration
Receiver Output DataSW001 SW002 SW003 Format
L L L 16- to 24-bit left–justifiedL H L 16- to 24-bit l2S16-bit right-justified (orH L H
standard)
18-bit right-justified (orL H H
standard)
Pressing the SW004 pushbutton initiates a reset operation of the CS8414.
SLEU057A – September 2004 – Revised May 2009 Description 9Submit Documentation Feedback

1.7 SW006 Operation Control for DAC
1.8 Jumper Connection
1.9 Demonstration Software
SW006 Operation Control for DAC www.ti.com
Switch SW006 is the register set and reset control for the PCM1796 and DSD1796. The RESET section ofthe switch must be set to Hexcept to perform a reset operation. Table 1-2 shows the options for SW006.
Table 1-2. SW006 Options
SW006 RESET Function
H Normal operation (default)L Reset operation
JP001 selects the normal or inverted BCK signal for 24-bit left-justified or other formats (I
2
S); the defaultposition is I
2
S.
Demonstration software is provided to control the PCM1796/DSD1796 internal register using a PC that isrunning the Microsoft
®
Windows
®
operating system. This software uses a printer cable to connect the PCto the DEM-PCM/DSD1796 connector CN003.
The demonstration software includes a total of five files in the DEM1796 directory of the supplied CD.These files are:•DEM1796.exe
•DEM1796.ini
•Vbrjp200.dll
•Ver.dll
•Inpout.dll
To load the software, first copy these files to a convenient directory (folder), such as:C:\DEM1796
Then, change the printer-port address in the DEM1796.ini initialization file to:& H378, & H278, or & H3BCO
Most PCs use & H378 as the default printer-port address.
10 Description SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

Chapter 2SLEU057A – September 2004 – Revised May 2009
Schematics, PCB Layout, and Bill of Materials
This chapter provides the DEM-DAI/ASDAC and the DEM-AS/CDAC printed circuit boards andschematics. The bill of materials (BOM) is included for component and manufacturer reference.
Note: Board layouts are not to scale. These are intended to show how the board is laid out; theyare not intended to be used for manufacturing DEM-DAI1753/54/55 EVM PCBs.
Topic .................................................................................................. Page
2.1 DEM-DAI/ASDAC Printed Circuit Board Layout ............................. 122.2 DEM-AS/CDAC Printed Circuit Board Layout ................................ 152.3 DEM-DAI/ASDAC Schematics ..................................................... 172.4 DEM-AS/CDAC Schematics ........................................................ 192.5 Component Lists....................................................................... 20
SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 11Submit Documentation Feedback

2.1 DEM-DAI/ASDAC Printed Circuit Board Layout
DEM-DAI/ASDAC Printed Circuit Board Layout www.ti.com
Figure 2-1 through Figure 2-3 illustrate the printed circuit board (PCB) layout for the DEM-DAI/ASDAC.
Figure 2-1. DEM-DAI/ASDAC Silkscreen
12 Schematics, PCB Layout, and Bill of Materials SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

www.ti.com DEM-DAI/ASDAC Printed Circuit Board Layout
Figure 2-2. DEM-DAI/ASDAC (Top View)
SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 13Submit Documentation Feedback

DEM-DAI/ASDAC Printed Circuit Board Layout www.ti.com
Figure 2-3. DEM-DAI/ASDAC (Bottom View)
Schematics, PCB Layout, and Bill of Materials14 SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

2.2 DEM-AS/CDAC Printed Circuit Board Layout
www.ti.com DEM-AS/CDAC Printed Circuit Board Layout
Figure 2-4 through Figure 2-6 illustrate the PCB layout for the DEM-AS/CDAC.
Figure 2-4. DEM-AS/CDAC Silkscreen
Figure 2-5. DEM-AS/CDAC (Top View)
SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 15Submit Documentation Feedback

DEM-AS/CDAC Printed Circuit Board Layout www.ti.com
Figure 2-6. DEM-AS/CDAC (Bottom View)
Schematics, PCB Layout, and Bill of Materials16 SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

2.3 DEM-DAI/ASDAC Schematics
R101
220
U101
NJM5534
R105
180
C105 8200pF
2
3
6
4R113
100
C103
0.027uF
R109 200
C101
10uF
RST
MDO
MDI
MC
ML
SCLK
VCC
VCC
GND
GND
(NC)
(NC)
(NC)
(NC)
VOUTL
VOUTL+
GND
GND
VOUTR
VOUTR+
(NC)
AVCC
AVCC+
(NC)
GND
GND
VDD
/16V
CLKO
BCK
LRCK
DATA
(NC)
MUTE
VDD
VDD
GND
GND
RESET
MDO
MDI
MC
ML
AGND
D_SCLK
CLKO/D_BCK
P_SCLK
DSD_R
P_BCK
P_LRCK
P_DATA
DSD_L
CN101
XB 3 7 20
C102
10uF
VCC1
/16V
CN102
XB 3 7 20
CN103
RCA pj
AGND
D SCLK
D BCK
DSD R
DSD L
AVCC
AVCC+
7
AVCC+
C109
10uF
/16V
C111
10uF
/16V
AVCC
C107
8200pF
R107
180
R103
220
R111
200
R102
220
U102
NJM5534
R106
180
C106 8200pF
2
3
6
4R114
100
C104
0.027uF
R110 200
CN104
RCA pj
7
AVCC+
C110
10uF
/16V
C112
10uF
/16V
AVCC
C108
8200pF
R108
180
R104
220
R112
200
VDD
C056
10uF
/16V
C054
100uF
/16V
C053
100uF
/16V
C051
0.1uF
C052
100uF
/16V
2
1
3
GND
INOUT
C055
0.1uF
U051
REG1117 3.3
VCC1
CN055
Banana
Jack
(Black)
CN053
Banana
Jack
(Blue)
CN054
Banana
Jack
(Red)
CN052
Banana
Jack
(Gray)
CN051
Banana
Jack
(Orange)
AVCC+
AVCC
CN058
C058
0.1uF
VCC2
C057
100uF
/16V
CN057
Banana
Jack
(Black)
CN056
Banana
Jack
(Red)
www.ti.com DEM-DAI/ASDAC Schematics
The schematic for the sections of the DEM-DAI/ASDAC are shown in Figure 2-7 through Figure 2-9 .
Figure 2-7. DEM-DAI/ASDAC Analog Section (Sockets for Daughterboard and Low-Pass Filter)
Figure 2-8. DEM-DAI/ASDAC Connector and Regulator
SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 17Submit Documentation Feedback

FFC-4BMEP1
U003 74VHC14
U004 74HCT32
U002
C
Cd/F1
Cc/F0
Cb/E2
Ca/E1
C0/E0
VD+
DGND
RXP
RXN
FSYNC
SCK
CS12/FCK
U
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VERF
Ce/F2
SDATA
ERF
M1
M0
VA+
AGND
FILT
MCK
M2
M3
SEL
CBL
CS8414
2
1
3
U001
TORX173
CN001
RCA pj
R001
75
C001
0.01uF
C002 0.01uF
C004
0.1uF
C003
10uF
/16V
C005
10uF
/16V
C006
0.1uF C007
10uF
/16V
C008
0.1uF
C011 0.1 uF
R003
47k
R004
470
D001
1SS133
SW004
FP1F 2M
C012
10uF
/16V
C010 0.1 uF
R002
470
C009
0.068uF
(C015)
100uF/16V
32
GND
1
OUTIN
(C016)
0.1uF
(FIL001)
(CN004)
FFC 48BMEP1
GND
GND
1
2
3
4
5
6
7
14
13
12
11
10
9
8
GND
U005
74VHC244
C013 0.1 uF
1
25
[SCLK]
SW001
FT1D 2M
SW002
FT1D 2M
SW003
FT1D 2M
SW005
FT2D 2M
[BCK]
[LRCK]
[BCK(INV)]
INT(CS8414)
EXT
DAI select
[LRCK]
[BCK]
[DATA]
[SCLK]
[LRCK]
[BCK]
[DATA]
[SCLK]
[BCK]
[e-DATA]
C014
GND
U006
74VHC244
1
19
CN003
57LE 40360 7700(D3)
SW006
DSS104
RA001
47k x5
[ML]
[MC]
[MDI]
[RST ]
MDO
RST
[MDO]
1
2
3
4
(L001)
CN002
FFC 2BMEP1
[DATA]
JP001
456
VCC2
18
36
VDD
0.1 uF
MDI
MC
ML
24
48
[e-LRCK]
[e-BCK]
[e-SCLK]
[e-DATA]
[e-LRCK]
[e-BCK]
[e-SCLK]
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
VCC
VCC
VCC
VCC
1
2
3
4
5
6
7
14
13
12
11
10
9
8
SCLK
BCK
LRCK
DATA
DSD-L
DSD-R
D-BCK
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
D-SCLK
(TORX179P)
C018
10uF
/16V
C017
10uF
/16V
AGND
CN006
XB 3 7 20
JP002
FFC
2BMEP1
CN007
XB-3-7-20
DEM-DAI/ASDAC Schematics www.ti.com
Figure 2-9. DEM-DAI/ASDAC Digital Section (Digital Audio Interface)
Schematics, PCB Layout, and Bill of Materials18 SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback

2.4 DEM-AS/CDAC Schematics
C024
C020
C016
C012
C002
0.1uF
Vcc1
(NC)
MUTE
VDD
VDD
GND
GND
RESET
MDO
MDI
MC
ML
AGND
D_SCLK
CLKO/D_BCK
P_SCLK
DSD_R
P_BCK
P_LRCK
P_DATA
DSD_L
U002
NJM5534
R005 820
C011 2700pF
C005
10uF
/16V
(R003) C014
10uF/16V
C013
10uF/16V
C010
Jumper
(R004)
VCC
VCC
GND
GND
(NC)
(NC)
(NC)
(NC)
VOUTL
VOUTL+
GND
GND
VOUTR
VOUTR+
(NC)
AVCC
AVCC+
(NC)
GND
GND
U003
NJM5534
R006 820
C015 2700pF
C018
10uF/16V
C017
10uF
/16V
U004
NJM5534
R009 820
C019
2700pF
(R007) C022
10uF/16V
C021
10uF
/16V
C016
Jumper
(R008)
U005
NJM5534
R010 820
C023 2700pF
C026
10uF/16V
C025
10uF
/16V
DSDL
DSDR
DBCK
PLRCK/WDCK
PDATA/DFD/PDI
PBCK
SCKI
DGND
VDD
MS
MDI
MC
MDO
RST
C004
0.1uF
C006
10uF
/16V
R002
10k
C003
10uF
/16V
C001
10uF/16V
U001
DSD1796
(R001)
C009
0.1uF
C008
10uF
/16V
5
2
3
6
4
7
8
5
2
3
6
4
7
8
5
2
36
4
7
8
5
2
36
4
7
8
22pF
22pF
22pF
22pF
C007
0.1uF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
VCC2L
AGND3L
IOUTL
IOUTL+
AGND2
VCC1
VCOML
VCOMR
AGND1
IOUTR
IOUTR+
AGND3R
VCC2R
IREF
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Vcc1
www.ti.com DEM-AS/CDAC Schematics
Figure 2-10 shows the schematic for the sections of the DEM-AS/CDAC.
Figure 2-10. DEM-AS/CDAC
SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 19Submit Documentation Feedback

2.5 Component Lists
2.5.1 DEM-AS/CDAC_96/98 Parts List
2.5.2 DEM-DAI/ASDAC_96/98 Parts List
Component Lists www.ti.com
Table 2-1 lists the bill of materials for the DEM-AS/CDAC_96/98.
Table 2-1. Bill of MaterialsQty RefDes Item Value Mfr Part No Manufacturer Remarks
11 C001, C003, C008, AL ELE capacitor 10 µF/16 V ROA–16V100M ELNAC013, C014, C017,C018, C021, C022,C025, C026
2 C002, C007 Film capacitor 0.1 µF AMFF0050J104 Nissei
2 C004, C009 Chip film capacitor 0.1 µF ECHU1C104JB Matsushita
2 C005, C006 AL ELE capacitor 10 µF/16 V ROA-16V100M ELNA
0 C010, C027 Film capacitor 0.1 µF AMFF0050J104 Nissei Jumper connection
4 C011, C015, C019, Film capacitor 2700 pF APSF0100J272 NisseiC023
4 C012, C016, C020, Ceramic capacitor 22 pF RPE131CH220J50 MurataC024
1 R001 Resistor 47 k ΩSN14C2C–47k ΩF KOA Not mounted
1 R002 Resistor 10 k ΩSN14C2C–10k ΩF KOA
2 R003, R007 Resistor 4.7 k ΩSN14C2C–4.7k ΩF KOA Not mounted
6 R004, R005, R006, Resistor 820 ΩSN14C2C–820 ΩF KOA R004, R008 notR008, R009, R010 mounted
1 U001 DAC 28-pin, DSD1796 TIJSSOP
PCM1796
PCM1798
4 U002, U003, U004, Op amp 8-pin, SOP NJM5534M JRCU005
Table 2-2 lists the bill of materials for the DEM-DAI/ASDAC_96/98.
Table 2-2. Bill of MaterialsQty RefDes Item Value Mfr Part No Manufacturer Remarks
2 C001, C002 Film capacitor 0.01 µF AMFF0050J103 Nissei
C003, C005, C007,7 C109, C110, C111, AL ELE capacitor 10 µF/16 V ROA-16V100M ELNAC112
C004, C006, C008,6 Film capacitor 0.1 µF AMFF0050J104 Nissei C016 not mountedC016, C051, C058
1 C009 Film capacitor 0.068 µF AMFF0050J683 Nissei
C010, C011, C013,5 Ceramic capacitor 0.1 µF RPE132F104Z50 MurataC014, C055
1 C012 AL ELE capacitor 10 µF/16 V SME16VB10M ELNA
C015, C052, C053,5 AL ELE capacitor 100 µF/16 V ROA-16V101M ELNA C015 not mountedC054, C057
1 C056 Tantalum capacitor 10 µF/16 V DN1C100M1S NEC
C101, C102, C017,2 AL ELE capacitor 10 µF/16 V R3A-16V100M ELNAC018
2 C103, C104 Film capacitor 0.027 µF APSF0100J273 Nissei
C105, C106, C107, C017, C108 not4 Film capacitor 8200 pF APSF0100J822C108 mounted
1 L001 Inductor Not mounted
20 Schematics, PCB Layout, and Bill of Materials SLEU057A – September 2004 – Revised May 2009Submit Documentation Feedback