Texas Instruments TLV320AIC3111 EVM User manual

User's GuideSLAU285 – July 2009
TLV320AIC3111 EVM
This user’s guide describes the operation of the TLV320AIC3111 EVM evaluation module (EVM). TheEVM features a TLV320AIC3111 stereo audio codec, amplifiers for speakers and headphones, and adigital signal processing module. Together with the USB-MODEVM board, the TLV320AIC3111 ControlSoftware and a PC running Windows™ XP it is a plug-and-play solution to evaluate the capabilities of theTLV320AIC3111.
The information in a caution or a warning is provided for your protection. Read each caution and warningcarefully.
Contents1 EVM Overview ............................................................................................................... 21.1 Introduction .......................................................................................................... 21.2 Box Contents ........................................................................................................ 21.3 Related Documentation From Texas Instruments .............................................................. 22 EVM + PC .................................................................................................................... 32.1 EVM Preparation .................................................................................................... 32.2 Control Software .................................................................................................... 32.3 Installation ........................................................................................................... 42.4 Concepts ............................................................................................................. 42.5 Main Window ........................................................................................................ 52.6 Dialogs and Active Objects ........................................................................................ 63 EVM Hardware ............................................................................................................. 173.1 Connectors and Jumpers......................................................................................... 173.2 EVM Schematics .................................................................................................. 203.3 EVM Bill of Materials .............................................................................................. 21Appendix A USB-MODEVM Schematic ...................................................................................... 23Appendix B USB-MODEVM Bill of Materials ................................................................................ 24Appendix C USB-MODEVM Protocol ......................................................................................... 26
List of Figures
1 TLV320AIC3111 EVM + USB MODEVM ................................................................................. 32 Main Window ................................................................................................................. 53 Initialization Script ........................................................................................................... 74 Command Dialog ............................................................................................................ 85 Register Inspector ........................................................................................................... 96 Clock and Digital Signal Routing ......................................................................................... 117 Digital Configuration: Codec Clock / PLL ............................................................................... 128 Advanced Clock Settings. ................................................................................................. 139 Audio Interface .............................................................................................................. 1410 Automatic Gain Control .................................................................................................... 1511 DRC Transfer Function and DRC Dialog ............................................................................... 16
List of Tables
1 Analog I/O ................................................................................................................... 17
I2S, I2C are trademarks of Koninklijke Philips Electronics N.V.Windows is a trademark of Microsoft Corporation.
SLAU285 – July 2009 TLV320AIC3111 EVM 1Submit Documentation Feedback

1 EVM Overview
1.1 Introduction
1.2 Box Contents
1.3 Related Documentation From Texas Instruments
EVM Overview www.ti.com
2 Jumpers ..................................................................................................................... 173 Expansion Connectors P4/J4 ............................................................................................. 184 Expansion Connectors P5/J5 ............................................................................................. 185 Power Supply ............................................................................................................... 19B-1 USB-MODEVM Bill of Materials .......................................................................................... 24C-1 USB Control Endpoint HIDSETREPORT Request .................................................................... 26C-2 Data Packet Configuration ................................................................................................ 26C-3 GPIO Pin Assignments .................................................................................................... 29
The TLV320AIC3111 EVM features a TLV320AIC3111 stereo audio codec, amplifiers for speakers andheadphones and a digital signal processing module.
Together with the USB-MODEVM board, the TLV320AIC3111 Control Software and a PC runningWindows XP, it is a plug-and-play solution to evaluate the capabilities of the TLV320AIC3111.
The USB-MODEVM board contains a TAS1020B streaming audio USB controller, which enumerates as aUSB audio class device.
When the USB-MODEVM + TLV320AIC3111 EVM is connected to a PC running Microsoft Windows XP, itwill be recognized as a sound card. Once the TLV320AIC3111 is configured using the TLV320AIC3111control software, any audio playback and record software on the PC that uses the Windows audiosubsystem (sound card) can use the TLV320AIC3111.
The following items ship with the TLV320AIC3111 EVM:•TLV320AIC3111 EVM•USB-MODEVM
The control software required to operate the EVM is available from the TLV320AIC3111 product folder athttp://www.ti.com
TLV320AIC3111 data sheet (SLAS644 )
TLV320AIC3111 EVM2 SLAU285 – July 2009Submit Documentation Feedback

2 EVM + PC
2.1 EVM Preparation
TLV320AIC3111EVM
SW2
J9 right speaker
J6 ext in
USB-MODEVM
J14
J8 left speaker
Headset
J7 USB
ON OFF
microphone
2.1.1 Analog Signal Connections
2.2 Control Software
www.ti.com EVM + PC
This chapter explains how to use the TLV320AIC3111 EVM with a PC running Windows XP.
To interface the TLV320AIC3111 EVM with a PC using USB, plug the TLV320AIC3111 EVM onto theUSB-MODEVM as shown in Figure 2 1. TLV320AIC3111 EVM + USB MODEVM.
Figure 1. TLV320AIC3111 EVM + USB MODEVM
Note: USB-MODEVM configuration
To control the TLV320AIC3111 from the PC via the USB-MODEVM, set switch SW2 position1, 3, 4, 5, 6, 7 to ON and position 2 and 8 to OFF.
•Connect a headphone to J14 (3,5 mm jack)•Connect 8- Ωspeakers to J8 and J9 (two 3-screw terminals)– Left speaker to SPLN and SPLP– Right speaker to SPRN and SPRP•By default, the on-board microphone is connected to the ADC. To use the line input (J7), refer to sheet1 of the AIC3111_RHB_EVM schematics (chapter 3.2)
The TLV320AIC3111 control software exposes most features of the TLV320AIC3111 through an intuitivegraphical user interface.
SLAU285 – July 2009 TLV320AIC3111 EVM 3Submit Documentation Feedback

2.3 Installation
2.4 Concepts
EVM + PC www.ti.com
Note: Before Windows on the PC can use the TLV320AIC3111 EVM as a sound card, theTLV320AIC3111 on the EVM must be configured (sampling rate, audio routing, internalamplifier settings etc.) with the TLV320AIC3111 control software.
Download the TLV320AIC3111 control software (SLAC289 ) from the TLV320AIC3111 product folder athttp://www.ti.com and launch the program (SLAC289 ).
This file is a self-extracting archive. The default target folder is:
C:\Program Files\Texas Instruments\AIC3111Click the Unzip button to complete the installation.
The TLV320AIC3111 control software is now available in the target folder. The name of the executable isCodecControl.exe
To launch the TLV320AIC3111 control software, navigate to the target folder with the Windows Explorerand double click CodecControl.exe.
The TLV320AIC3111 control software presents a block diagram view of the TLV320AIC3111 (or selectmodules within the TLV320AIC3111).
The block diagram consists of active objects that can react to user input (for example switches oramplifiers with variable gain that show a volume control on a mouse click event).
Note: Each active object will change color to red if the mouse cursor is above the object. Clickingthe object will trigger its function.
Some active objects are linked to control register(s) of the TLV320AIC3111 in a two way fashion. If anEVM is connected, the control software will update the appropriate register(s) whenever an active object istriggered. If a register that is linked to an active object is changed via other components (for example thescript interpreter or the register inspector), the active object will change its state accordingly.
The control software will automatically detect a TLV320AIC3111 EVM once it is connected to a USB portof the PC.
If no TLV320AIC3111 EVM is connected to the PC, the control software changes to a simulation mode,where it is possible to retrieve script commands based on user input within the block diagram.
TLV320AIC3111 EVM4 SLAU285 – July 2009Submit Documentation Feedback

2.5 Main Window
•Full featured TLV320AIC3111
•Playback only
•Record only
www.ti.com EVM + PC
Figure 2. Main Window
At the top of the main window is a tool bar with buttons to change between four different use cases of theTLV320AIC3111:
By default, the control software displays the full featured block diagram of the TLV320AIC3111.
Each use case has its own initialization script, which will run if a use case is selected by clicking on one ofthe use case buttons. The initialization script contains register settings for the TLV320AIC3111 toconfigure the device for a specific use case.
The toolbar contains a control that determines the zoom factor. Change the zoom by selecting the desiredzoom factor.
To move the block diagram, click on a blank area within the block diagram and drag the diagram with themouse.
At the bottom of the main window is a status bar that provides information about the state of thecommunication between the control software and the TLV320AIC3111 EVM. It also shows hints aboutelements in the block diagram, for example the I2C page and register / bit location of a selected switch.
Audio signal paths (both digital and analog) will change color from black to•Blue for left audio output•Turquoise for right audio output•Magenta for audio input
SLAU285 – July 2009 TLV320AIC3111 EVM 5Submit Documentation Feedback

2.5.1 Using Active Objects
2.6 Dialogs and Active Objects
EVM + PC www.ti.com
once they are activated via switches. This feature visualizes all audio paths and immediately highlights if apath is disabled.
Moving the mouse pointer over an active object will light up the active object (the color of the object turnsred).
For example, the Class-A/B HP Driver left amplifier active object will turn from its inactive state to its activestate when the mouse pointer enters the amplifier symbol:
Clicking the activated object will trigger its function. In the case of the amplifier active object, the functionis a volume control. Moving the volume control slider changes the volume setting of the amplifier (it is alsopossible to change the volume by clicking onto the number within the amplifier symbol and typing the newgain setting).The control software updates the appropriate register in the TLV320AIC3111 and as a resultthe volume on the headphone output will change accordingly.
The TLV320AIC3111 control software contains several dialog windows that give access to additionalfeatures.
Most dialogs are linked to active objects and are opened by clicking on the active object.
A few dialogs are not linked to active objects and are opened using the View menu.
6TLV320AIC3111 EVM SLAU285 – July 2009Submit Documentation Feedback

2.6.1 Init Script Dialog
Each use case , , , owns a unique initialization script which will automatically run when a
www.ti.com EVM + PC
TLV320AIC3111 EVM is detected or if the user selects another use case.
To show or edit the initialization script, choose View->Init Script …from the main window menu bar.
Figure 3. Initialization Script
Click the Run button to run the script again. For further information about the script syntax, see Figure 3 .
SLAU285 – July 2009 TLV320AIC3111 EVM 7Submit Documentation Feedback

2.6.2 Command Dialog
EVM + PC www.ti.com
Open the command dialog (View->Command …) to write, edit, load, save and run command scripts.Command scripts are text files that contain commands to communicate with the TLV320AIC3111. Thesyntax is described in Figure 4 .
Figure 4. Command Dialog
•The main area of the command dialog is command buffer (editable text) which contains the commandscript. To run the command script, click the Run button.•The smaller read only text area on the right side of the command dialog displays control data readfrom the TLV320AIC3111. The Clear button clears the Read Data field.•The one line text edit field on the left bottom allows single command execution.•The Record check box enables recording of commands generated by the control software.
Figure 4 shows a recording of the volume control for the left Class-A/B HP Driver amplifier (note that theRecord checkbox is checked).
A single command to read four bytes starting at address 0x28 was executed and the result is displayed inthe Read Data field.
TLV320AIC3111 EVM8 SLAU285 – July 2009Submit Documentation Feedback

2.6.3 Register Inspector
www.ti.com EVM + PC
The register inspector dialog (View->Register Inspector …) gives access to all registers of theTLV320AIC3111.
Figure 5. Register Inspector
The register inspector displays the content of the TLV320AIC3111 registers. The control software will readall TLV320AIC3111 registers when a TLV320AIC3111 EVM is detected. To force reading the content ofone page, click the Refresh button.•The Page edit field selects the page to be displayed.•The addr column shows the address of the registers within the selected page in decimal notation.•The description column contains a description for each register. If the register has no functionassigned, it is declared Reserved.•The data columns show the data of each register (one byte). The first data column uses decimalnotation, the second uses hexadecimal notation. It is possible to change the register value by clickinginto one of the data fields and typing the new value (either decimal or hexadecimal).•The numbered columns show the register content in binary notation. Read/Write bits are shown solidblack or red; read only bits are gray or dark red. Red numbers represent bits that recently changed. Tochange a single writeable bit, click on the bit and it will flip.
SLAU285 – July 2009 TLV320AIC3111 EVM 9Submit Documentation Feedback

2.6.4 DAC Filter
EVM + PC www.ti.com
One of the digital signal processing blocks of the TLV320AIC3111 implements five digital biquad filters.The DAC digital filter dialog (View->DAC Filter …) allows real time graphical manipulation of the digitalfilters.
The control software will automatically configure the digital signal processing block when the DAC digitalfilter dialog is opened.
The digital filter dialog limits the range of each digital biquad filter to +/-12[dB] (this is an arbitrary limitationfor demonstration purposes).•Each biquad has its own unique handle with a unique color. Each handle will light up white if themouse pointer is in the vicinity, showing that it can be selected. To change the frequency and gain of abiquad, grab and drag its handle.It is also possible to change the gain using the slider for each biquad.•Each biquad can be configured for parametric EQ, Shelf Treble or Shelf Bass. If it is configured for EQ,press the shift key before selecting the handle to adjust the bandwidth of the EQ using the mousepointer.
•Due to digital range limitations, the biquads will automatically scale, if the biquad coefficients exceedthe limitations.
The coordinate system will shift accordingly to reflect the resulting attenuation.•To avoid clipping, add additional attenuation with the Attenuate slider.•To retrieve the biquad coefficients, open the command dialog (see 0) and check Record.
TLV320AIC3111 EVM10 SLAU285 – July 2009Submit Documentation Feedback

2.6.5 Clock and Digital Signal Routing
www.ti.com EVM + PC
The TLV320AIC3111 has a flexible and complex clock and digital signal routing architecture.
Two processors can connect to the TLV320AIC3111 using two separate I2S™ interfaces: The primary I2Sinterface has dedicated pins whereas the secondary I2S interface signals can be assigned to a selectionof pins.
The TLV320AIC3111 has an on-chip clock generation module which can be configured to generate thesampling rate, modulator clocks, converter clocks, bit clock and word clock.
Click on the “Digital Audio Processing Serial Interface” active object (if it is not within the current scope ofthe main window, drag the block diagram to the left until the active object appears). This will change theblock diagram to the clock and digital signal routing diagram:
Figure 6. Clock and Digital Signal Routing
The clock and digital signal routing diagram shows the current state of the TLV320AIC3111 routingconfiguration and allows interactive manipulation.•Each clock or signal source has its own unique color. For example, the BCLK signal from the internalclock generation module has a turquoise color.•To trace the routing of a specific signal, follow its color. The example in Figure 6 shows that the BCLKsignal from the internal clock generation module is routed to the primary I2C™ BCLK pin (which isconfigured as an output), to the secondary I2S BCLK signal (which is not connected to a pin) and tothe BCLK input of the codec (ADC and DAC within the TLV320AIC3111).•To change the definition of a pin (input or output), click the active object (arrow) that belongs to the pin.Only pins that can change between input and output are linked to such an active object. The clockrouting diagram will automatically change to reflect the new routing.•Some of the switches within the diagram are active objects, which can be manipulated using themouse pointer. Other switches open or close depending on the state of the associated pin.•To assign a pin to a signal of the secondary I2S interface, choose one of the available pins in the dropdown box that belongs to the signal. The list of available pins will change automatically depending onthe assignment of other signals to pins.•Click on the “Back To Codec” active object to return to the previous block diagram.•Click on the “Internal Clock Gen Module” active object to display the digital configuration dialog.
SLAU285 – July 2009 TLV320AIC3111 EVM 11Submit Documentation Feedback

2.6.6 Digital Configuration
EVM + PC www.ti.com
The digital configuration dialog gives access to the codec clock and PLL settings as well as the audiointerface settings.
To open the digital configuration dialog, navigate to the clock and digital signal routing diagram (seeFigure 6 ) and click on the “Internal Clock Gen Module” active object.
Figure 7. Digital Configuration: Codec Clock / PLL
The digital configuration dialog contains two tabs, one for the Codec Clock / PLL settings and one for theAudio Interface settings.
The Codec Clock / PLL settings tab (see Figure 7 ) enables simple generation of PLL and clock dividersettings based on the available input frequency and the desired sample rate:1. Choose the clock input using the Clock Input drop down box.2. Type the available input frequency in the Input Frequency edit field.3. Type the desired sample rate in the Sample Rate edit field of the ADC. By default, the DAC samplerate equals the ADC sample rate. Uncheck DAC Fs = ADC Fs and enter the DAC sample rate fordifferent sample rates.4. The Engine OSR and Instructions fields affect the miniDSP. Please contact your TI representative forfurther information about the miniDSP.5. The Results list shows all clock settings that fulfill the chosen parameters. Double click on one of theresults to program the TLV320AIC3111 with the new settings.
Each result has the following columns:
12 TLV320AIC3111 EVM SLAU285 – July 2009Submit Documentation Feedback

www.ti.com EVM + PC
•PLL: On or Off•P,R,J,D: PLL configuration•NADC, MADC: ADC clock dividers•AOSR: ADC over-sampling factor•FsADC: ADC sampling rate•NDAC, MDAC: DAC clock dividers•DOSR: DAC over-sampling factor•FsDAC: DAC sampling rate
Click the Advanced …button to show the advanced clock settings dialog.
Figure 8. Advanced Clock Settings.
The advanced clock settings dialog gives direct access to the PLL and codec clock dividers. It willrecalculate the clock results dynamically whenever a parameter is changed.
The internally generated bit clock signal (BCLK) can be derived from several sources and divided by aninteger number. Select the desired source with the Source drop down box, choose the divisor and enablepower to the divider, if required.
It is possible to put out a clock signal CLKOUT. Select the clock source, the divider and the destination pinusing the advanced clock settings dialog.
SLAU285 – July 2009 TLV320AIC3111 EVM 13Submit Documentation Feedback

2.6.7 Audio Interface
EVM + PC www.ti.com
The Audio Interface tab ( see Figure 9 ) contains controls to manipulate the digital audio interface:
Figure 9. Audio Interface
Use the Format drop down box to change the digital audio interface format:•I2S•DSP
•Right Justified•Left Justified
For details about the digital audio interface formats see the TLV320AIC3111 data sheet (SLAS550 ), 5.4AUDIO DIGITAL I/O INTERFACE.
The Word Length drop down box defines the number of bits per audio word.
The DIN/DOUT offset defines where the data for the ADC or from the DAC is located in the bit-stream.This is required for TDM (DSP) interface format.
TLV320AIC3111 EVM14 SLAU285 – July 2009Submit Documentation Feedback

2.6.8 AGC
labeled AGC within the block diagram for the full TLV320AIC3111 .
www.ti.com EVM + PC
The TLV320AIC3111 has an automatic gain control module, which is accessible by an active object
Clicking on the AGC active objects opens the AGC Dialog:
Figure 10. Automatic Gain Control
If the AGC is enabled, the TLV320AIC3111 will adjust the gain of the analog audio input signal amplifierso that the input signal level for input signal amplitudes above the noise threshold approximates the targetlevel.
•The main display in the AGC dialog shows the Amplitude of the ADC output data in decibel with 0dBequal to a full scale signal.•
– The target level line can be adjusted using the mouse pointer. It will change color to red if it themouse pointer is in the vicinity, indicating that it can be moved (click and drag).– The noise threshold line is also adjustable•The small display on the left shows the ADC output data•The AGC Gain field shows the applied gain (if the AGC is enabled) and allows setting a maximum gainusing the slider.
Advanced AGC controls are available by clicking the More button. This will reveal further controls to adjustvarious AGC parameters.
SLAU285 – July 2009 TLV320AIC3111 EVM 15Submit Documentation Feedback

2.6.9 Digital Volume Control and DRC
TLV320AIC3111 and the playback use case .
EVM + PC www.ti.com
The TLV320AIC3111 has digital volume control and dynamic range compression modules for each DACchannel. Each is accessible by a active objects labeled DVol within the block diagram for the full
Clicking on the DVol active object opens the DAC Vol dialog, which contains a slider to set the digitalvolume and several options. Checking the DRC option reveals the DRC transfer function.
Figure 11. DRC Transfer Function and DRC Dialog
The horizontal axis of the DRC transfer function shows the input to the DRC and the vertical axis showsthe output of the DRC. The green line shows the gain below the DRC threshold, the magenta coloredhorizontal line shows the DRC threshold and the red line shows the gain above the DRC threshold.
The DRC transfer function will change depending on the digital volume setting and the DRC threshold.
Click on the DRC transfer function to reveal the DRC dialog, which contains a slider to change the DRCthreshold.
TLV320AIC3111 EVM16 SLAU285 – July 2009Submit Documentation Feedback

3 EVM Hardware
3.1 Connectors and Jumpers
www.ti.com EVM Hardware
This chapter contains information about the EVM Hardware (switches, jumpers, schematics).
Table 1. Analog I/O
Connector Function
J6 1 MIC1LP
2 AGND
3 MIC1LM or MIC1RPJ7 MicrophoneJ8 1 SPLM (Speaker)2 AGND
3 SPLP (Speaker)J9 1 SPRM (Speaker)2 AGND
3 SPRP (Speaker)J10 1 HPL2 AGND
3 HPRJ11 1 SPRM (Speaker Filtered)2 AGND
3 SPRP (Speaker Filtered)J12 1 BATT.SVDD
2 AGNDJ13 1 HPL (Headphone)
2 AGND
3 HP (Headphone)J14 HeadsetJ15 Headphone Filtered
Table 2. Jumpers
Jumper Function Positions Default
W1 MIC bias select 1-2: 3.3V 1-2: 3.3V2-3: EVMW2, W3 On-board MIC 1-2: add MIC populatedW4 MIC bias to MIC1RP 1-2: connect populatedW5 MIC bias to MIC1LP 1-2:connect populatedW6 MIC bias to MIC1RP 1-2: 1.0k populatedload
Removed: 2.2kW7 J7 MIC bias select 1-2: MIC1RP 1-2: MIC1RP2-3: MIC1LMW8 MIC1LM termination 1-2: AC to AGND 1-2: AC to AGND2-3: 1.0k to AGNDW9 VOL/HED_DET select 1-2: VOL 1-2: VOL2-3: HED_DETW10 AVDD current wire 1-2: connected populated (removeloop to measure current)
SLAU285 – July 2009 TLV320AIC3111 EVM 17Submit Documentation Feedback

EVM Hardware www.ti.com
W11 SVDD current wire 1-2: connected populated (removeloop to measure current)W12 SVDD current wire 1-2: connected populated (removeloop to measure current)W13 HVDD current wire 1-2: connected populated (removeloop to measure current)W14 DVDD current wire 1-2: connected populated (removeloop to measure current)W15 IOVDD current wire 1-2: connect populated (removeloop to measure current)
Table 3. Expansion Connectors P4/J4
Pin Number Signal Description
P4.1/J4.1 NCP4.2/J4.2 NCP4.3/J4.3 NCP4.4/J4.4 DGND Digital GroundP4.5/J4.5 NCP4.6/J4.6 NCP4.7/J4.7 NCP4.8/J4.8 NCP4.9/J4.9 NCP4.10/J4.10 DGND Digital GroundP4.11/J4.11 NCP4.12/J4.12 NCP4.13/J4.13 NCP4.14/J4.14 RESET TAS1020B ResetP4.15/J4.15 NCP4.16/J4.16 NCP4.17/J4.17 NCP4.18/J4.18 DGND Digital GroundP4.19/J4.19 NCP4.20/J4.20 NC
Table 4. Expansion Connectors P5/J5
Pin Number Signal Description
P5.1/J5.1 NCP5.2/J5.2 NCP5.3/J5.3 BCLK Audio Serial Data Bus Bit ClockP5.4/J5.4 DGND Digital GroundP5.5/J5.5 NCP5.6/J5.6 NCP5.7/J5.7 WCLK Audio Serial Data Bus Word ClockP5.8/J5.8 NCP5.9/J5.9 NCP5.10/J5.10 DGND Digital GroundP5.11/J5.11 SDIN Audio Serial Data Bus Data InputP5.12/J5.12 NCP5.13/J5.13 SDOUT Audio Serial Data Bus Data OutputP5.14/J5.14 NC
18 TLV320AIC3111 EVM SLAU285 – July 2009Submit Documentation Feedback

www.ti.com EVM Hardware
P5.15/J5.15 NCP5.16/J5.16 SCL I2C ClockP5.17/J5.17 MCLK Master Clock InputP5.18/J5.18 DGND Digital GroundP5.19/J5.19 NCP22.20/J5.20 SDA I2C Data
Table 5. Power Supply
Pin Number Signal
P3.1/J3.1 NCP3.2/J3.2 NCP3.3/J3.3 +5VAP3.4/J3.4 NCP3.5/J3.5 DGNDP3.6/J3.6 AGNDP3.7/J3.7 +1.8VDP3.8/J3.8 NCP3.9/J3.9 +3.3VDP3.10/J3.10 NC
SLAU285 – July 2009 TLV320AIC3111 EVM 19Submit Documentation Feedback

3.2 EVM Schematics
EVM Hardware www.ti.com
The schematic diagram for the TLV320AIC3111EVM is provided as a reference.
TLV320AIC3111 EVM20 SLAU285 – July 2009Submit Documentation Feedback