Texas Instruments TPA3136D2 User manual

1
SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
User's Guide
SLOU444A–May 2016–Revised May 2016
TPA3136D2 Evaluation Module
This user’s guide describes the operation of the TPA3136D2EVM. The user’s guide also provides design
information such as schematic, BOM, and PCB layout.
Contents
1 Hardware Overview.......................................................................................................... 2
2 Operation ..................................................................................................................... 3
2.1 Electrostatic Discharge Warning.................................................................................. 3
2.2 Unpacking the EVM ................................................................................................ 3
2.3 Power Supply Setup................................................................................................ 3
2.4 Evaluation Module Preparations.................................................................................. 3
2.5 Inputs and Outputs ................................................................................................. 4
2.6 Power Up ............................................................................................................ 4
2.7 Recommended Settings ........................................................................................... 4
3 Board Layouts, Bill of Materials, and Schematic ........................................................................ 5
3.1 TPA3136D2EVM Board Layouts ................................................................................. 5
3.2 Bill of Materials...................................................................................................... 6
3.3 TPA3136D2EVM Schematic ...................................................................................... 7
List of Figures
1 TPA3136D2EVM............................................................................................................. 2
2 TPA3136D2EVM Top Composite Assembly............................................................................. 5
3 TPA3136D2EVM Bottom Composite Assembly ......................................................................... 5
4 TPA3136D2EVM Schematic ............................................................................................... 7
List of Tables
1 TPA3136D2EVM Specifications ........................................................................................... 2
2 Power Requirements........................................................................................................ 3
3 TPA3136D2EVM Setting 1 ................................................................................................. 4
4 TPA3136D2EVM Setting 2 ................................................................................................. 4
5 TPA3136D2EVM Parts List................................................................................................. 6

Hardware Overview www.ti.com
2SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
1 Hardware Overview
The TPA3136D2 EVM customer evaluation module demonstrates the TPA3136D2 integrated circuit from
TI.
The TPA3136D2 is a 10-W (per channel) efficient stereo digital amplifier power stage for driving 2 bridge-
tied speakers. This document covers EVM specifications and design documentation that includes
schematics, a parts list, and layout design.
Figure 1 illustrates the EVM board.
Figure 1. TPA3136D2EVM
Table 1 lists the specifications for the EVM board.
Table 1. TPA3136D2EVM Specifications
Key Parameters Value
Power Supply Voltage 4.5 V to 14.4 V
Number of Channels 2 Bridge-Tied Load (BTL) Stereo
Load Impedance 4 Ω(12 V) to 6 Ω(> 12 V)
Output Power BTL 10 W per channel into an 8-Ωload

www.ti.com Operation
3
SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
2 Operation
This section describes the TPA3136D2EVM board in regards to power supply and system interfaces.
Information regarding handling and unpacking, absolute operating conditions, and a description of the
factory default switch and jumper configuration are provided.
The following is a step-by-step guide to configuring the TPA3136D2EVM for device evaluation.
2.1 Electrostatic Discharge Warning
Many of the components on the TPA3136D2EVM are susceptible to damage by electrostatic discharge
(ESD). Customers are advised to observe proper ESD handling precautions when unpacking and handling
the EVM, including the use of a grounded wrist strap at an approved ESD workstation.
CAUTION
Failure to observe ESD handling procedures may result in damage to EVM
components.
2.2 Unpacking the EVM
On opening the TPA3136D2EVM package, ensure that the following item is included:
• 1 piece TPA3136D2EVM board using one TPA3136D2
If this item is missing, contact the Texas Instruments Product Information Center nearest you to inquire
about a replacement.
2.3 Power Supply Setup
A single power supply is required to power up the EVM. Since most of the pins are PVCC-compliant, the
PVCC supply can also be used to power the analog supply (AVCC) and can be used to pull up the logic
pins for shutdown (SD) control, and fault detection (FAULT).
Table 2. Power Requirements
Description Voltage Range Current Requirement Minimum Wire Size
PVCC 4.5 to 14.4 V 4 A 24 AWG
CAUTION
Applying voltages above the limitations given in Table 2 may cause permanent
damage to your hardware.
2.4 Evaluation Module Preparations
Prepare the EVM in the following manner:
1. Ensure that the external power source is set to OFF.
2. Connect the external regulated power supply adjusted from 4.5 V to 14.4 V to the module PVCC and
GND banana jacks taking care to observe marked polarity.

Operation www.ti.com
4SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
2.5 Inputs and Outputs
Configure the inputs and outputs on the EVM:
1. For a BTL configuration, connect a load or loads across the outputs (OUTL+ and OUTL–) and (OUTR+
and OUTR–).
2. For PBTL configuration, connect a single load from one of the left speaker jacks to one of the right
speaker jacks, depending on how the filters are loaded. Apply a single input, differential or single-
ended, to the RIN RCA phono plug and PBTL pin (pin 14) is tied high with J13 out.
2.6 Power Up
Use the following settings for power up:
1. Select the desired gain and mode of operation via J13 (IN = BTL, OUT = PBTL). Configure the input
mode (J6/J10, OUT = Differential input mode, IN = Single-ended input mode).Verify correct voltage
and input polarity and turn the external power supplies ON. The EVM should begin operation.
2. Adjust the audio source for the correct volume.
2.7 Recommended Settings
The following list provides the settings for two different configurations:
1. Single-ended input, auto-recovery mode, without Plimit, BTL (stereo output)
Table 3. TPA3136D2EVM Setting 1
Setting Description
J4 (LIN) L channel audio input
J9 (RIN) R channel audio input
J6, set to IN Single-ended input
J10, set to IN Single-ended input
J7, set to IN Able to change PLIMIT value with R6
R6 Change PLMIT voltage value
(setting R6 = 0 Ωdisables Plimit function)
J12 (SD = FAULT) set to IN Auto-recovery mode
J13 (PBTL) set to IN BTL mode
2. Single-ended input, auto-recovery mode, PBTL (mono output)
Table 4. TPA3136D2EVM Setting 2
Setting Description
J4 (LIN) No audio input
J9 (RIN) R channel audio input
J6, set to IN Single-ended input
J10, set to IN Single-ended input
J7, set to IN Able to change PLIMIT value with R6
R6 Change PLMIT voltage value
(setting R6 = 0 Ωdisable Plimit function)
J12 (SD = FAULT) set to IN Auto recover mode
J13 (PBTL) set to OUT PBTL mode

www.ti.com Board Layouts, Bill of Materials, and Schematic
5
SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
3 Board Layouts, Bill of Materials, and Schematic
3.1 TPA3136D2EVM Board Layouts
Figure 2 and Figure 3 illustrate the EVM board layouts.
Figure 2. TPA3136D2EVM Top Composite Assembly
Figure 3. TPA3136D2EVM Bottom Composite Assembly

Board Layouts, Bill of Materials, and Schematic www.ti.com
6SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
3.2 Bill of Materials
Table 5 displays the BOM for this EVM.
Table 5. TPA3136D2EVM Parts List
Designator Qty Value Description Package Part Number Manufacturer
C1 1 1uF CAP, CERM, 1 μF, 35 V, +/- 10%, X5R, 0603 0603 GMK107BJ105KA-T Taiyo Yuden
C2, C8 2 100uF CAP, AL, 100uF, 50V, +/-20%, 0.17 ohm, TH 8.0x10.5mm UHE1H101MPD Nichicon
C3, C9 2 0.1uF CAP, CERM, 0.1uF, 50V, +/-10%, X7R, 0603 0603 GRM188R71H104KA93D Murata
C4, C10 2 1000pF CAP, CERM, 1000pF, 50V, +/-5%, C0G/NP0, 0603 0603 GRM1885C1H102JA01D Murata
C5, C12, C21, C26 4 330pF CAP, CERM, 330pF, 50V, +/-5%, C0G/NP0, 0603 0603 GRM1885C1H331JA01D Murata
C6, C13, C22, C27 4 1000pF CAP, CERM, 1000 pF, 100 V, +/- 10%, X7R, 1206 1206 12061C102KAT2A AVX
C7, C14, C23, C28 4 1000pF CAP, CERM, 1000 pF, 50 V, +/- 10%, C0G/NP0, 0603 0603 06035A102KAT2A AVX
C11, C15, C16, C24, C25 5 1uF CAP, CERM, 1uF, 16V, +/-10%, X7R, 0603 0603 GRM188R71C105KA12D Murata
C17, C18, C19, C20 4 0.22uF CAP, CERM, 0.22 μF, 25 V, +/- 10%, X7R, 0603 0603 GRM188R71E224KA88D Murata
J1, J3, J11 3 Binding Post, RED, TH 11.4x27.2mm 7006 Keystone
J2, J5, J8 3 Binding Post, BLACK, TH 11.4x27.2mm 7007 Keystone
J4 1 RCA Jack, White, R/A, TH PC Mount Phono Jack-
White, TH 970 Keystone
J6, J7, J10, J12, J13 5 Header, 100mil, 2x1, TH Header, 2x1, 100mil, TH 800-10-002-10-001000 Mill-Max
J9 1 RCA Jack, Red, R/A, TH PC Mount Phono Jack-Red,
TH 971 Keystone
L1, L3 2 100 ohm Ferrite Bead, 100 ohm @ 100 MHz, 8 A, 2-Pin SMD, Body 4.5 x 3.2
mm, Height 2.55 mm 2-Pin SMD, Body 4.5 x 3.2 mm, Height 2.55 mm HI1812V101R-10 Laird-Signal Integrity Products
L2, L4, L5, L6 4 300 ohm Ferrite Bead, 300 ohm @ 100 MHz, 3.1 A, 0806 0806 NFZ2MSM301SN10L Murata
R1, R3, R7, R10 4 10.0 RES, 10.0, 1%, 0.25 W, 0603 0603 CRCW060310R0FKEAHP Vishay-Dale
R2, R4, R8, R11 4 68 RES, 68, 5%, 0.1 W, 0603 0603 CRCW060368R0JNEA Vishay-Dale
R5 1 10.0k RES, 10.0k ohm, 0.1%, 0.1W, 0603 0603 RG1608P-103-B-T5 Susumu Co Ltd
R6 1 100k TRIMMER, 100k ohm, 0.5W, TH 375x190x375mil 3386P-1-104LF Bourns
R9 1 100k RES, 100k ohm, 1%, 0.063W, 0402 0402 CRCW0402100KFKED Vishay-Dale
R12 1 100k RES, 100k ohm, 1%, 0.1W, 0603 0603 RC0603FR-07100KL Yageo America
S1 1 Switch, Tactile, SPST-NO, 0.05A, 12V, SMT Switch, 4.4x2x2.9 mm TL1015AF160QG E-Switch
SHUNT1,SHUNT2,
SHUNT3,SHUNT4, SHUNT5 5 1x2 Shunt, 100mil, Gold plated, Black Shunt SNT-100-BK-G Samtec
TP1, TP2 2 Black Test Point, Compact, Black, TH Black Compact Testpoint 5006 Keystone
TP3, TP4, TP6, TP7, TP8,
TP9, TP10 7 Orange Test Point, Miniature, Orange, TH Orange Miniature Testpoint 5003 Keystone
TP5 1 Red Test Point, Compact, Red, TH Red Compact Testpoint 5005 Keystone
U1 1 15-W Filter-Free Stereo Class-D Audio Power Amplifier With
Speakerguard, PWP0028E PWP0028E TPA3136D2PWP Texas Instruments

SD
1FAULT 2
LINP
3
LINN
4
NC
6
NC
13
NC
5
PBTL
14
GVDD
9
GND 8
RINN
11
RINP
12
PLIMIT
10
AVCC
7
PVCCR
15 PVCCR
16
BSPR 17
OUTPR 18
PGND 19
OUTNR 20
BSNR 21
BSNL 22
OUTNL 23
PGND 24
OUTPL 25
BSPL 26
PVCCL
27 PVCCL
28
PAD 29
U1
TPA3136D2PWP
1µF
C11
21
S1
SHUTDOWN
100k
R9
PVCC
GND
GND
LINP
LINN
RINN
RINP
PVCC
100k
R12
TP3
LINP
4
3
1
J4
LIN
PVCC
J3
OUTL+
PVCC
1µF
C1
8A
L3 PVCCR
100 µF
C8
0.1µF
C9
1000pF
C10
GND GND GND
PVCC
8A
L1 PVCCL
100 µF
C2
0.1µF
C3
1000pF
C4
GND GND GND
GND
1µF
C15 TP4
LINN
1µF
C24
GND
TP7
LINP
4
3
1
J9
RIN
1µF
C25 TP8
LINN
TP5
GVDD
100k
R6
10.0k
R5
GND
GND
TP6
PLIMIT
J6
J10
J7
1µF
C16
GND
J13
PBTL
GND
LINP
LINN
RINP
RINN
PLIMIT
PBTL
J12
SD=FAULT
SD
FAULT
SD
TP10
FAULTz
TP9
SHUTDOWNz
PVCC
GND
J1
PVCC
J2
GND
GND
TP1
GND
OUTPL
OUTNL
OUTNR
OUTPR
0.22µF
C17
0.22µF
C18
0.22µF
C19
0.22µF
C20
330pF
C5
10.0
R1
3.1A
L2
1000pF
C6
1000pF
C7
OUTL+
OUTL-
OUTR-
OUTR+
GND
GND
GND
OUTPL
68
R2
GND
1
J5
OUTL-
330pF
C12
3.1A
L4
1000pF
C13
1000pF
C14
GND
GND
68
R4
GND
1
J8
OUTR-
330pF
C21
3.1A
L5
1000pF
C22
1000pF
C23
GND
GND
68
R8
GND
J11
330pF
C26
3.1A
L6
1000pF
C27
1000pF
C28
GND
GND
68
R11
GND
OUTPR
OUTNL
TP2
GND
FAULT
OUTNR
10.0
R3
10.0
R7
10.0
R10
GND
Copyright © 2016, Texas Instruments Incorporated
www.ti.com Board Layouts, Bill of Materials, and Schematic
7
SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback Copyright © 2016, Texas Instruments Incorporated
TPA3136D2 Evaluation Module
3.3 TPA3136D2EVM Schematic
Figure 4 illustrates the EVM schematic.
Figure 4. TPA3136D2EVM Schematic

Revision History www.ti.com
8SLOU444A–May 2016–Revised May 2016
Submit Documentation Feedback
Copyright © 2016, Texas Instruments Incorporated
Revision History
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (May 2016) to A Revision ........................................................................................................... Page
• Changed board image. ................................................................................................................... 2

STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1. Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3Regulatory Notices:
3.1 United States
3.1.1 Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2 For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER

FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1 For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1 Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2 Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1. Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
3. Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER

【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3 Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1 User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2 EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5. Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER

SPACER
6. Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7. USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8. Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9. Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated