The Handy THIS User manual

Page 1
OPERATOR’S MANUAL AND PARTS LIST
2400W IMPACT SHREDDER - THIS
Sales & Helpline 01793 333220
www.thehandy.co.uk
Before use please read & understand this manual, paying particular
attention to the safety instructions.
2010 v1

Page 2
CONTENTS
SAFETY INSTRUCTIONS 3
MAJOR PARTS 4
ASSEMBLY 5
OPERATION 6
PARTS DIAGRAM AND LIST 7-8
EC DECLARATION OF CONFORMITY 9

Page 3
SAFETY INSTRUCTIONS
Read and understand the owner’s manual and labels afxed to the
electric shredder. Learn its application and limitations as well as the
specic potential hazards. Retain these instructions for reference.
• TheImpactShredderisanelectricalapplianceusingfastmovingparts
 andassuchcanbedangerousifhandledirresponsibly.
• Ensurethatnoforeignobjectssuchasstones,glass,metal,earthor
 plasticsarefedintotheshredder;thesecouldcausebluntingofthe
 bladeandseriouslydamagethemotor.
• Onlyuseextensioncablesthatareapprovedforoutdooruse.Check
 thattheyareingoodcondition.
• Useglovesandearprotectionifoperatingforextendedperiodsoftime.
• Werecommendsafetygogglesarewornduringoperationasobjects
 canbeejectedathighspeedwhenthemotorisrunning.
•  Allonlookers,childrenandpetsshouldbekeptatasafedistanceand
 onlythosefamiliarwiththeoperationoftheshreddershouldbe
 permittedtouseit.
• Neverexposetheunittorainormoistureandstorethemachineina
 totallydryenvironment.
• Alwaysturnofftheunitandfullydisconnectfromthemainselectricity
 supplywhencleaningorperforminganymaintenance.Waituntilthe
 cuttingdiscstops.
• Neverinserthandsintothefeedhopperordebrischutewhilsttheunit
 isrunningorconnectedtothemainselectricitysupply.
• Donotmodifytheunitinanyway.
• Replacewornordamagedpartsusingonlyoriginalspares.
• Nevermovetheshredderbypullingonthecableandalwaysswitchoff
 whentransporting.Donotleavetheshredderunattendedwhilstitis
 switchedon.

Page 4
MAJOR PARTS
Handle
Hopper
ShredderBody MotorCover
DischargeChute
Axle
PowerCord
CoverSecuringKnob
MainSwitch
OverloadResetButton
Supports

Page 5
ASSEMBLY
• InserttheAxlethroughthepre-drilledholesintheFootSupports.
• Insertthesupportsintothebodyoftheshredderasshown.
• AttacheachWheeltotheAxleintheordershownbelowand
ensurethatthenutisnottootight.(Fromlefttoright-washer,
axlesleeve,wheel,washer,nut,wheelcover).Somemodelsmay
nothavetheaxlesleeve.
• OnthebodyofthemachinetightentheCoverSecuringKnob.This
knobhasasafetyswitchbuiltintoitandthemachinewillnotacti-
vateunlesstheknobistightened.
• Attachthecollectionbagtothemachinebymeansofthehookson
thesidesofthedischargechute.
• Donotusetheshredderwithoutthehopper.
SPECIFICATION
Model No THIS
Voltage 230-240V~50Hz
Power S1:2000W,S6:2400W
No-loadSpeed 4500rpm
MaxBranchDiameter 40mm
SoundPowerLevel 107dB(A)
LengthofCable 0.35m
ProtectionClass IPX4
NetWeight 14kg

Page 6
OPERATION
• Placethemachineonrm,levelgroundwhilstoperatingandplacereceptacleunder-
neaththedischargechuteorattachthecollectionbag.
• Presstheswitchmarked“I”tostartand“0”tostopthemotor.Presstheoverloadreset
buttonifthemachinedoesnotwork,ensuringyouhaveconnectedtothepowersupply.
• Allowthemotortorunforafewsecondsbeforecommencingwork.
• Inspectthematerialtobeshreddedbeforestartingandremoveanysharpobjects,
stones,wireetcwhichcoulddamagethecuttingmechanism.
• Themachinewillautomaticallypullthewastematerialin.Donotforcetoomuchmate-
rialinatonceotherwisethechutemayblockup.
• Ifablockageoccursandthebladestopworking,disconnectthemachineandfreeany
jammedmaterial.Ifthebladestallsformorethan5seconds,theoverloadswitchwillcut
inandswitchoffthemachine.Allowthemachinetocoolforatleast1minutebeforeat-
temptingtore-start.Pushtheoverloadswitchrst,thentheOn/Offswitch.
• Thereisaplungerprovidedtoaidthethefeedingofsoftermaterial-donotfeedsoft
kitchenwasteintotheshredder-itisbettertocompostit.
Hints and Tips:
• Usethemachinetoshredthefollowingmaterialsonly-twigsandbranches(maxdia
40mm),pruningtrimmings,hedgetrimmings,plantmaterialandroots(removesoilrst).
• Bealerttolongleafbrancheswhichcanwhipbackastheyarebeingdrawnintothe
shredder.
• Organicmaterialwhichcontainsalargeamountofwaterandsapcansticktothecutting
blades-itisbesttoleaveitforafewdaystodryout.
• Tomakenercomposttheshreddedmaterialcanbepassedthroughasecondtime.
• Keeptheventilationslotsonthebodyfreeofdustanddebris.
• Donotleavetheshredderrunningunattended;disconnecttheplugwhenleavingor
movingthemachine.
Blade Replacement:
• Thebladeshavetwocuttingedges.Whenthebladesbecomeworntheycanbere-
versedtousethesecondcuttingedgebuttheseshouldbechangedbyanauthorised
servicedealer.
• Whenbothedgesofthebladeshavebecomeworntheymustbereplacedas a pair.
Thebladescanbere-sharpenedbutthismustbedonebyaprofessionalusinganoil
stone.Theweightofeachbladeiscriticaltomaintainthebalanceofthecuttingdisc.
Maintenance:
• Duringanymaintenanceworkensurethatthemachineisswitchedoffanddisconnected
fromthemains.
• Ifanextensioncableisuseditmustbeofthesamegradeasthatttedtotheshredder.
Checkthecablesregularlyforsignsofdamageorwear.
• Neverattempttooverridetheoverloadswitch-itisthereforyoursafety.
• Removealldepositedmatterafterusewithabrushandcleanthemachineandallplas-
ticpartswithsoapandadampcloth.
• Donotcleantheshredderwithahosepipeorbyrinsing.Nowatershouldbeallowedto
entertheshredder.

Page 7
PARTS DIAGRAM

Page 8
PARTS LIST
No Part No Desc No Part No Desc
1 TH101-911365002 WarningSticker 2 TH101-9151650001 Hopper
3 TH101-9053650006 RubberFlap 4 TH101-9150650001 ClampBar
5TH101-9SBABC4.2-20 Screw 6 TH101-9114-650001 Logo
7 TH101-9001650001 UpHousing 8 TH101-6053650005 BoltFramePlate
9 TH101-9SBABC04-10 Screw 10 TH101-9WSB-4 SpringWasher2
11 TH101-9030650001 SwitchPin 12 TH101-9057-650001 Plunger
13 TH101-9SBABC05-20 “H”TypeScrew 14 TH101-9SBABC08-30 Screw
15 TH101-9WSB-08 SpringWasher1 16 TH101-907265000 ClampBlock
17 TH101-9132650001 Screw 18 TH101-9132650001 BladeSetInc
Screws
19 TH101-9072650001 BladePlate 20 TH101-9072650002 DriveBlock
21 TH101-9053650008 BladeDefendBlock 22 TH101-9057650003 PullBar
23 TH101-9030650004 Washer3 24 TH101-9NCN04 Nut
25 TH101-9SBABC4.2-18 Screw 26 TH101-9002650001 DownHousing
27 TH101-9058650001 Knob 28 TH101-9060650001 Spring
29 TH101-9030650002 InternalNut 30 TH101-9075650001 Nut
31 TH101-9053650007 NutFramePlate 32 TH101-9NAN-04 HexNut
33 TH101-9032650001 OverloadSwitch 34 TH101-9029650001 PowerCord
35 TH101-9023630001 CordSheath 36 TH101-9053650001 CordClampPlate
37 TH101-9053650004 SwitchFramePlate 38 TH101-9SBABC05-20 Screw
39 TH101-9SBABC04-40 Screw 40 TH101-9131650001 Filter
41 TH101-9027650001 ConnectingWire1 42 TH101-9027650002 ConnectingWire2
43 TH101-9032650002 Electromagnetic
Switch
44 TH101-9092650001 Overcurrent
protection
45 TH101-9113650001 DataSticker 46 TH101-9142650001 MotorCover
47 TH101-9033620001 Capacitor 48 TH101-9022650001 Fan
49 TH101-9023650002 ShaftSheath 50 TH101-9DB-6080Z Bearing
51 TH101-9SBABC04-75 Screw 52 TH101-9039650001 MotorSupport
53 TH101-9005650001 Field 54 TH101-9013650001 Armature
55 TH101-9DB-62010Z Bearing 56 TH101-9030650005 Washer
57 TH101-9031650004 SmallBeltWheel 58 TH101-9053650002 WindDefendBoard
59 TH101-9138650001 PlasticPin 60 TH101-9069650003 DownCoverGear-
box
61 TH101-9DB6290Z Bearing 62 TH101-9031650003 EccentricWheel
63 TH101-9031650002 BigBeltWheel 64 TH101-9047650001 Belt
65 TH101-9069650002 UpCoverGearbox 66 TH101-9DB-60030Z Bearing
67 TH101-9098650001 Spanner 68 TH101-9069650001 WheelCover
69 TH101-9NCN-08 HexNut 70 TH101-9030650003 Washer
71 TH101-9038650001 SupportTube 72 TH101-9057650002 ConnectingPole
73 TH101-9030650003 Washer 74 TH101-9023650001 WheelAxleSleeve
75 TH101-9031650001 Wheel 76 TH101-101-BAG CollectionBag

Page 9
DeclarationofConformity
PursuanttotheregulationsofthefollowingECDirectives:
-ElectromagneticCompatabilityDirective89/336/EEC
-LowVoltageDirective73/23/EEC
-MachineryDirective98/37/EC
-NoiseEmissionDirective2000/14/EC
HandyDistributionLtdherebydeclaresthattheproduct:
MachineType:Impact Shredder
MachineModel:THIS
ConformstothemainsafetyrequirementsoftheECDirectiveslistedabove.
Thisconformityisbasedonthefollowingstandardsandnormativedocuments:
EN 55014-1:2000+A1+A2
EN 55014-2:1997+A1
EN 61000-3-2:2000
EN61000-3-11:2000
EN 60335-1:2002+A1+A11
EN 13683:2003
98/37/EC-AnnexI
Theresponsibleperson,basedwithintheEC,isidentiedbelow
Name:MrDerekBelcher
Title:ManagingDirector
Company:HandyDistributionLtd
Address:HobleyDrive,StrattonStMargaret,SWINDON,SN34NS
Signature:      Date:20thFeb2008   
EC DECLARATION OF CONFORMITY

Page 10
Toordersparepartsandseethecompleterangeofgarden
machineryandgardenequipmentfromHandy,visit:
www.thehandy.co.uk