The Handy THET1400 User manual

22-11-2017
1400W
ELECTRIC TILLER
Model No: THET1400 -- Product No: 193855002
ASSEMBLY REQUIRED
SAVE THESE INSTRUCTIONS
SPARES & SUPPORT: 01793 333212
Please read & understand this manual, paying attention to the safety instructions,
before use.
The manufacturer reserves the right to change the product specification and livery
according to continued product improvements.
All images used are for illustration purposes only.
INSTRUCTION MANUAL

CONTENTS
SPECIFICATIONS
IMPORTANT INFORMATION
GENERAL SAFETY INSTRUCTIONS
ELECTRICAL CONNECTION
SET UP & PREPARATION FOR OPERATION
MAINTENANCE & STORAGE
TROUBLE SHOOTING
PARTS LISTS & DIAGRAM
WARRANTY
EC DECLARATION OF CONFORMITY
If you require any assistance with regards to the contents or operation of your
machine, please contact us:
Tel: [phone]
Email: [email protected]
Monday to Friday 8.00am to 5.30pm
(excl. Bank Holidays)
SPECIFICATIONS
The manufacturer reserves the right to change the product specification and livery according to
continued product improvements.
Model
THET1400
Product Number
193855002
Motor Power
1400 watt
Motor Voltage
230V/50HZ
Idle Speed
330min-1
Working Width
430mm
Working Depth
200mm
Cable Length
10m
Max. Vibration
1.359m/s², k=1.5m/s²
Noise Level LWA
93 dB(A)

IMPORTANT INFORMATION
WARNING
Read this instruction manual carefully before operating this machine. Make sure that you are familiar with
the controls and properly operate the machine. Following these instructions can reduce the risk of fire,
electric shock and personal injury.
IF NOT USED PROPERLY THIS MACHINE CAN BE DANGEROUS!
This machine can cause serious injury to the operator and others, the warning and safety instructions
must be followed to ensure reasonable safety and efficiency in using this product. The operator is
responsible for following the warning and safety instructions in this manual and on the machine. Never
use the product unless the blades or guards are correctly positioned.
DESIGNED FOR DOMESTIC USE ONLY.
The 1400 watt Electric Tiller is designed for use in private gardens, whose annual use does not generally
exceed 50 hours & are primarily used for tilling shrubberies and allotments, but not in public facilities,
parks or sports grounds and not for agricultural or forestry use.
Compliance with this manual supplied by the manufacturer is a prerequisite for the proper usage of the
machine. The operating manual contains servicing & maintenance instructions as well as directions for
use.
TRAINING
Read the instructions carefully: Be familiar with the controls and the proper use of the equipment.
Never allow children or people unfamiliar with these instructions to use the product. Local regulations
can restrict the age of the operator.
Never operate while people, especially children, or pets are nearby.
Keep in mind that the operator or user is responsible for accidents or hazards involving the machine that
occur to other people or their property.
ELECTRICAL REQUIREMENTS
Connect the main leads to a standard 230V+10% (50Hz+1Hz) electrical supply which has protection
devices for under-voltage, over-voltage, over-current as well as a residual current device (RCD) with
maximum residual current rated at 0.03A.
EXTENSIONS LEADS
Extension cables must be no longer than 50 metres in length. The cable section must be 1.5 mm² for cable
lengths up to 25 metres & 2.5 mm² for cable lengths over 25 metres & 230V to allow sufficient current
flow to the motor.
Improper use of extension cables may cause inefficient operation of the tiller, which can result in
overheating and motor damage.
Only extension cords to H07RN-F specification intended for outdoor purpose may be used. Avoid use of
free and inadequately insulated connections. Connections must be made with protected material suitable
for outdoor use. Make sure that any extension cable connections are dry and safe. Ensure that the
extension cable is carefully laid out avoiding liquids, sharp edges and places where vehicles might run over
it. Avoid allowing the extension cable to come into contact with the tiller tines. Ensure your extension
cable is fully extended to prevent overheating or the risk of fire.
WORKING CONDITIONS
This machine is a domestic use model. It is designed for operating under ambient temperatures between
+5°C and 40°C and for installation at altitudes no more than 1000m above M.S.L. The surrounding
humidity should be less than 50% at 40°C. It can be stored or transported under ambient temperatures
between -25°C and 55°C.

GENERAL SAFETY INSTRUCTIONS
It is important that you read and understand the owner’s manual and labels affixed to the machine.
Learn its application and limitations as well as the specific potential hazards. Retain these
instructions for future reference. The operator is responsible for following the warnings &
instructions in this manual and on the product.
A. CAUTION - Read & understand operator’s manual before using the machine. Failure to
follow instructions could result in death or serious injury.
B. CAUTION - Whenever the machine is in use, safety glasses must be worn to safeguard
against flying objects. We also recommend the use of ear protection.
C. DANGER - Keep hands & feet away from the rotating tines.
D. Keep all bystanders & animals at least 10 metres away from the machine during operation. If
approached, stop the machine immediately.
E. DO NOT use the machine in wet weather conditions.
F. CAUTION - Stop the machine immediately if the power cable or plug becomes damaged.
G. Disconnect from power supply when not in use, before moving, adjusting, changing parts,
cleaning, or working on the machine. Never open the motor cover before disconnecting the
electrical plug from the power supply.
Safety alert symbol. Used to alert you to potential personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in serious injury.
WARNING
Indicates a potentially hazardous situation which, if not avoided, could result in serious injury
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
CAUTION
Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided,
may result in property damage.

STAY ALERT
Do not operate the machine while under the influence of drugs, alcohol, or any medication that
could affect your ability to use it properly. Do not use this machine when you are tired or distracted
from the job at hand. Be aware of what you are doing at all times. Use common sense.
AVOID DANGEROUS CONDITIONS
Make sure there is adequate surrounding workspace. Cluttered areas invite injuries.
Keep your work area clean with sufficient light. Keep the area around the machine clear of
obstructions, grease, oil, rubbish and other debris which could cause persons to fall onto moving
parts.
INSPECT YOUR MACHINE
Check all bolts, nuts, and screws for tightness before each use, especially those securing guards and
drive mechanisms. Vibration during use, may cause these to loosen.
Form a habit of checking to see that all other tools/equipment are removed from the working area
before turning it on.
Replace damaged, missing or failed parts before using it. Warning labels carry important
information. Replace any missing or damaged warning labels.
DRESS PROPERLY
Do not wear loose clothing, gloves, scarfs, neckties or jewellery (rings, wrist watches), which can be
caught in moving parts. Protective electrically non-conductive gloves and non-skid heavy duty
footwear are highly recommended when working. Wear a face or dust mask if the operation is dusty.
Always wear safety glasses/goggles and/or face shields. Everyday eyeglasses have only impact
resistant lenses; they are not safety glasses/goggles. Wear protective hair covering to contain long
hair, preventing it from getting caught in machinery.
AVOID ELECTRICAL SHOCK
Check that the electric circuit is adequately protected and that it corresponds with the power,
voltage and frequency of the motor. Check that there is a ground connection, and a regulation
differential switch further up the circuit. Ground the log splitter. Prevent body contact with
grounded surfaces: pipes, radiators, ranges, and refrigerator enclosures. Never open the pushbutton
box on the motor. Should this be necessary, contact a qualified electrician. Make sure your fingers
do not touch the plug’s metal prongs when plugging or unplugging the log splitter.
KEEP BYSTANDERS AND CHILDREN AWAY
Keep unauthorised persons a minimum distance of 10 metres away from the machine. If
approached, stop the machine immediately. Do not allow children to handle or climb on the
machine.
DO NOT OVERREACH
Keep proper footing and balance at all times when using the machine. Never stand on the
machine. Serious injury could occur if the machine is tipped or if the moving parts are
unintentionally contacted. Do not store anything above or near the machine, where anyone might
stand on the machine to reach them.
AVOID INJURY FROM UNEXPECTED ACCIDENT
Keep hands & feet out of the way of all moving parts. Do not place any part of your body or any
tool e.g. in the machine during operation.
DO NOT FORCE TOOL
Always work within the rated capacity. Do not use the machine for a purpose for which it was not
intended.
NEVER LEAVE MACHINE RUNNING UNATTENDED
Do not leave the machine unattended until it has come to a complete stop.
MAINTAIN YOUR MACHINE WITH CARE
Clean the machine immediately after use. Keep the machine clean to ensure it operates to its full &
safest performance. When maintaining this machine, only the manufacturer’s original replacement
parts should be used. The use of non-original manufacturer parts may invalidate your warranty.

PROTECT THE ENVIRONMENT
Take left over materials to an authorised collection point or follow the stipulations in the country
where the machine is used. Do not discharge into drains, soil or water.
STORE IDLE EQUIPMENT
When not in use, the machine should be stored in a dry location. Keep the machine away from
children and others not qualified to use it.
Double insulated or class 2 electrical appliances are
products that have been designed in a way so as not to
require a safety connection to electrical earth (These
products must NOT have a safety connection to Earth).
Acoustic power level LWA accordance with directive
2000/14/EC + 2005/88/EC
(Please see machine & specification within this manual
for actual reading)
This symbol on the product or on its packaging indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic
equipment.
For more detailed information about recycling of this
product, please contact your local council office, your
household waste disposal service or shop where you
purchased the product.
ELECTRICAL CONNECTION
Do not connect either core to the earth pin
The insulation on the grounded three metre electrical cord will only remain effective if the original
insulating parts are used for repairs and the spaces between the original insulation are maintained.
The use of a Residual Current Device (“RCD”), on 230V electrics is recommended. If using an
extension cable, plug it directly into the RCD.
NOTE: A built-in thermal protector is fitted to shut off the motor to prevent it from overheating. The
thermal protector restores automatically when the motor cools down. We recommend the machine
is left to cool down for a period of more than 15 minutes, before an attempt is made to plug the
machine back to the mains and switched on for operation. If the machine still does not operate,
check RCD or extension cable for faults. If it still does not operate, contact your local approved
service dealer.

SET UP & OPERATION
Remove the Tiller and contents from the carton. Be sure the carton is empty before discarding.
If you require any assistance with regards to the contents of the Tiller, please contact us:
Tel: [phone]
Email: [e-mail]
Monday to Friday 8.30am –5.30pm (excl. Bank Holidays)
Description
1. Top Handle
2. Middle Handle
3. Cable Clip
4. Lower Guide Handle
5. Motor Housing
6. Fender
7. Tines
8. Wheel

CONNECTING THE HANDLES
•Attach the Middle Handle (2) onto the Lower Guide Handle (4) and secure it using two M6x45
screws and swing nuts supplied. (Image 2)
•Connect the Top Handle (1) to the Middle Handle (2) and secure it by two supplied screws and
swing nuts. (Image 1)
•Tighten all screws and nuts completely.
•Using the two supplied cable clips (3) affix the electrical cable to the Handles. (Image 3).
OPERATION
Before operating the machine, please ensure you are fully aware of the below instructions, failure
to do so, could invalidate your manufacturer’s warranty. Completely unwind the electrical cable.
ADJUSTING THE SPUR
The position of the spur defines the working depth. (Image 4)
Image A - Use this position for transportation.
•Press the button to release the wheels. Pull the wheels down until the lock piece engages into
the recess on the other side of the frame. Release the button and make sure the frame is locked
firmly.
Image B - Use this position for working.
•Press the button to release the wheels. Pull the wheel up until the lock piece engages into the
recess on the other side of the frame. Release the button and make sure the frame is locked
firmly.
STARTING
Image 6
•Use your thumb to press the safety button (I) on the left side of the right handle and then press
the trigger (II).
•The safety button is only used as a release, so that the motor can be started and does not have
to be depressed, once the motor has been started.
•To turn the motor off, simply release the operation switch (II).

TIPS DURING OPERATION
Use the tiller for breaking sod, preparing seedbeds, and for cultivating gardens and flower beds.
The tiller may also be used to dig small holes for planting saplings or potted plants.
•Move the appliance to the work area prior to starting the motor.
•Hold the appliance firmly, adjust the spur into the ground and raise the appliance and switch on
the motor at no load.
•Press down on the handles until the appliance has dug to the depth required and then apply only
sufficient pressure to maintain that depth.
•The tines will pull the tiller forward during operation.
•For deeper digging, best results can be achieved by several movements, especially when the
ground is very hard or rough.
•By pulling tiller back towards yourself, the tines will dig deeper and more aggressively.
•For breaking sod or deep tilling, allow the tines to pull the tiller forward to the end of your arm’s
reach, firmly pull the tiller back towards you. By repeatedly allowing the tiller to move forward
and then pulling back to you, the tiller will be most effective.
•If the tiller digs deep enough to stay in one spot, gently rock the tiller side to side to start the
tiller moving forward again.
•For preparing a seed bed, we recommend you apply one of the tilling patterns shown in Image 7.
A–Make two passes over the area to be tilled, the second at a right angle to the first.
B–Make two passes over the area to be tilled, the second overlapping the first.
•To prevent tripping take particular care when moving backwards and when pulling the tiller.
•Always let the tines rotate at top speed; do not work in such a way as to overload the appliance.
•Never pass the tiller over the extension cord; make sure the cord is always in a safe position
behind your back.
•Tilling only when it is suitable. Frozen or waterlogged ground, if cultivated, can cause poor soil
moisture movement.
•When working on inclines, always stand diagonally to the incline in a sturdy, safe stance. Do not
work on extremely steep slopes.
GENERAL USE
•Always operate the machine on a level surface, ensuring the machine to stable and fee from
obstructions
•If using an extension cable, ensure it is suitable for outdoor usage, 14AWG or above and no
more than 10 metres in length.

MAINTENANCE & STORAGE
WARNING
Improper maintenance & storage of the machine may void your warranty. Keep the machine clean
for better and safer performance.
MAINTENANCE
•Before each use, check all nuts & bolts to be sure they are sufficiently tightened.
•Keep all moving parts lightly greased, using Multi-purpose grease.
•Ensure the breather openings on the motor casing are open and clean from debris. If they are
blocked, the motor could overheat and shut the machine down.
•We recommend only manufacturer original parts are used when maintaining this machine.
Failure to do so could invalidate your manufacturer’s warranty.
CAUTION
Any maintenance and repairs carried out, to any electronic component must be undertaken by a
qualified technician.
CLEANING
•Keep your machine clean.
•Before cleaning, ensure it is unplugged from the mains.
•Thoroughly clean the machine at the end of each day’s operation.
•Clean the underside of the housing around the tines, protective shield and fender with a
scrubbing brush, and brush or soft cloth dampened with a mild soap and water mixture. Never
splash with water!
•To remove soil and debris from the tines and transmission, use a stiff brush or a dampened
cloth.
•Clean the air vents, and remove any remaining grass or dirt.
•Once cleaned, wipe the tine and shaft dry and apply a light coat of oil.
CAUTION
Clean the tool after each use. Failure to carry out proper cleaning can result in damage to the
appliance or cause it to malfunction.
WARNING
Injury may occur when working on the tines. Wear protective gloves.
CAUTION
Wipe off any external material on the motor cover. Do not use petrol, turpentine, lacquer or paint
thinner, dry cleaning fluids or similar products. The use of chemical products or solvents may affect
the properties of the cover which has been produced using high density polyethylene (PET).

WORN TINES
CAUTION
Disconnect the mains and wear protective gloves when you attempt any kind of maintenance to
the tines.
•Worn tines lead to poor performance and may overload the motor.
•Check the tines’condition before each use. Sharpen or replace the tines with new one when
necessary. It is recommended to have this done by an approved Handy dealer.
To remove and install the tines from/to the tine bracket. (Image 8)
•Loosen the screws on one side while holding the lock nuts from the other side.
•Pull the set of tines from the shaft.
•The sets of tines are re-installed in reverse order.
TRANSMISSION
The drain plug is located on the left side of gearbox housing. (Image 9)
•Check, replace or top up the gearbox lubricant after every 30 hours of operation or at least once
a year.
•Put the tiller on its left side and clean the transmission housing before removing the drain plug
to prevent dirt and debris from getting into the gearbox.
•Using a 5mm Allen key, unscrew both plugs. If necessary, disassemble tines.
•We recommend MOBILUX EP 023 grease and filled using a grease gun. 90g will fill an empty
gearbox until it begins to seep out around the edge of the hole of the nozzle.
•Check the O-ring on both plugs for sign of wear and damage, replace if necessary.
•Reinstall the fill & air release plugs, using 5mm Allen key until secure.
STORAGE
•For years of trouble free service, make sure the Tiller is clean and dry before storing.
•Wipe all metal surfaces with an oil-impregnated cloth to protect them from corrosion (non-
resinous oil), or spray a fine coat of oil.
•Before storing, clean the Tiller thoroughly as indicated above.
•Store indoors or in a protected area during severe weather and winter months. Fold the Top
Handle over and store in a suitable place
Air release
Grease Fill

TROUBLE SHOOTING
PROBLEM
POSSIBLE CAUSES
RESOLUTION
Motor cannot
be started
1. No power
2. Cable damaged
3. Overheat protection activated
1. Check mains supply
2. Check cable, replace or have repair by
approved electrician
3. Let the motor cool down for over 15
minutes, before your resume work.
a. Working depth too deep. Adjust tilling
depth. Run over same ground
multiple times, to reach required
depth.
b. Tines are blocked, remove debris
c. Soil is too hard, adapt working depth
accordingly. Run over same ground
multiple times, to reach required
depth.
Unusual Noise
1. Tines are blocked
2. Gearbox oil leak
3. Loose nuts, bolts, or other
fastening
1. Switch off the machine, wait for
remove the plug from the mains.
2. Contact your local approved dealer
3. Tighten all, if noise continues contact
your local approved dealer
Excessive
Vibration
1. Tines are damaged or worn
2. Working depth too deep
1. Replace the tines or have machine
inspected by approved dealer.
2. Adjust tilling depth. Run over same
ground multiple times, to reach
required depth.
Poor Tilling
Results
1. Working depth too low
2. Tines are damaged or worn
1. Adjust tilling depth.
2. Replace the tines or have machine
inspected by approved dealer.

PARTS DIAGRAM –THET1400 (193855002)

PARTS LIST –THET1400 (193855002)
Item
No
Part No.
Description
Qty
Item
No
Part No.
Description
Qty
1
TH217-182257003300
Shield
1
35
TH217-202811305010
Cotter pin
1
2
TH217-120421164050
Screw ST4x50
4
36
TH217-202811266070
Wheel Axle
1
3
TH217-132257263000
Coil
1
37
TH217-202811302070
Spur
1
4
TH217-
0022572600000
Motor
1
38
TH217-202811305010
Split Pin
1
5
TH217-120441120525
Screw M5x25
4
39
TH217-120411120410
Screw M4x10
1
6
TH217-182241221000
Motor Base
1
40
TH217-182811267200
Adjusting Knob
1
7
TH217-202241004030
Flexi-Shaft
1
41
TH217-120210020815
Washer
φ8×φ15×1.6
2
8
TH165-5
Rubber Seal
Φ14*Φ28*4.5
1
42
TH217-232811265020
Adjusting Spring
1
9
TH217-222231008000
Connector
1
43
TH217-202811263020
Support Pin
1
10
TH165-3
Bearing6200
1
44
TH217-120350020600
Nut M6
2
11
TH217-202241301000
Worm Shaft
1
45
TH217-232811262070
Holder
1
12
TH165-1
Bearing 608
1
46
TH217-120250001000
Ring
1
13
TH217-120350020500
Nut M5
4
47
TH217-202811264020
Adjusting Screw
1
14
TH165-24
Screw M8x40
4
48
TH217-120418120616
Screw M6x16
2
15
TH217-202252560010
Blade Set Right
C
1
49
TH217-202257221070
Protective Shield
1
16
TH217-120330020800
Nut M8
4
50
TH165-12
Screw ST3.9x19
6
17
TH165-25
Blade Set Right
A
1
51
TH217-192241245000
Rubber Seal
1
18
TH217-202211020020
Ring
2
52
TH217-
182257001200GM
Motor Housing
1
19
TH217-212241230080
Transmission
Case Right
1
53
TH217-182257004200
Label
1
20
TH165-29
Rubber Seal
Φ19*Φ27*4.5
2
54
TH165-21
Cable Holder
1
21
TH165-30
Oil Bearing
2
55
TH217-182257002200
Upper Housing
1
22
TH217-202231344020
Washer
Φ19.2*Φ34*1.5
2
56
TH217-120421163916
Screw ST3.9x16
2
23
TH217-202257201010
Tine Shaft
1
57
TH217-120418120630
Screw M6x30
4
24
TH217-202241302000
Worm Wheel
1
58
TH217-120330020600
Nut M6
4
25
TH217-212241240080
Transmission
Case Left
1
59
TH217-202257222070
Lower Guide
Handle
1
26
TH165-36
O-Ring
2
60
TH217-242216601000
Sponge Sleeve
1
27
TH165-37
Transmission
Screw
2
61
TH165-45
Handle Fixing Knob
(Green)
4
28
TH165-39
Screw M6x16
9
62
TH165-13
Screw M6x45
4
29
TH165-38
Blade Set Left B
1
63
TH165-14
Cable Clip (Green)
2
30
TH217-202252500010
Blade Set Left D
1
64
TH217-202225002100
Middle Handle
1
31
TH217-182231267200
Wheel Cover
2
65
TH217-182225201200
Handle Brace
1
32
TH217-120411120512
Screw M5x12
2
66
TH217-182411422210
Gearbox Drain Plug
2
33
TH217-120210020815
Washer
φ8×φ15×1.6
2
67
TH217-120421264213
Screw ST4.2x30
2
34
TH217-182251380200
Wheel
2
68
TH217-
0022572400000GM
Top Handle
1

EC DECLARATION OF CONFORMITY
We Handy Distribution Ltd - SN3 5HY (Importer) declare that the product:
Designation: 1400w Electric Tiller
Model(s): THET1400
Product No. 193855002
Motor Power: 1400 watt
Motor Voltage: 230V/50HZ
Idle Speed: 330min-1
Type/Serial No. As per rating label on machine
Complies with the following directives:
2006/42/EC - Machinery Directive
2004/108/EC –Electro Magnetic Directive
2000/14/EC –Noise Directive
The conformity assessment procedure followed was in accordance with
EN 55014-1:20016+A1+A2, EN55014-2:1997+A1+A2, EN 61000-3-2:2006+A1+A2,
EN 61000-3-3:2013, EN ISO 3744:2010, EN 709:1997+A4, EN 60335-1:2012, EN 62233:2008
Notified Body:
TUV Rheinland LGA Products GmbH
Addresses:
Tillystrasse 2, 90431 Nurnberg, GERMANY
Additional Information
Guaranteed Sound Power: LWA = 93dB(A)
Max. Measured Vibration: 1.359m/s²
Authorised signatory & technical file holder
Date:
22/11/2017
Signature:
Name & Position
Mr. Simon Belcher - Managing Director
Company:
Handy Distribution Ltd
Address:
Murdock Rd, Dorcan, Swindon, Wiltshire, SN3 5HY.

For spares or support of your handy product,
please contact us:
Tel: [phone]
Email: [e-mail]
(Monday to Friday 8.00am to 5.30pm
excl. Bank Holidays)
To see our range of garden machinery & equipment visit:
www.thehandy.co.uk
Making gardening easier & affordable since 1938
Distributed by Handy Distribution, Murdock Road, Dorcan, Swindon, SN3 5HY