The World Models Manufacturing Super Frontier Senior User manual

Wing Span
Wing Area
Flying Weight
Fuselage Length
80.5 in / 2040mm
1232 sq in / 79.5 sq dm
7.0 lbs / 3300g
65.5 in / 1670mm
Warning !This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual
at hand for quick reference.
0.46 cu. in. displacement 2-cycle
Radio required : 4 channel 5 servos - radio w/ standard
* Specifications are subject to change without notice.*
Specifications
INSTRUCTION MANUAL
E
A
D
R
-
Y
T -
T
S
O
O
-
F
M
L
L
Y
A
Super
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
A088PO25531103
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com

Super
INDEX
P. 3 - 11
ASSEMBLY
BEFORE YOU BEGIN
P. 1
SAFETY PRECAUTIONS
P. 11
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
1
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for
warranty replacement. The manufacturer will replace any defective parts, but will not extend
to the parts that are good before gluing to defective parts during assembly. Warranty will
not cover any parts modified by customer.
2
Symbols used throughout this instruction manual comprise of the following : -
3
PARTS LIST
P. 2
P.1
3mm
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
Apply thread locker
Warning!
A088PO25531103

Parts List
1. MAIN WING -- 1 pair
2. SCREW PB2x20mm -- 4 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
CLEVIS PL4112103 -- 2 pcs
STRAPER PL4112102 -- 2 pcs
HORN PL4113101 -- 2 pcs
PUSHROD Ø1.8x130mm w/ Threads (For Aileron Servo ) -- 2 pcs
3. WOODEN 12x22x346mm (Wing Joiner)(A) -- 1 set
WOODEN Ø10x180.5mm (Wing Joiner)(B) -- 1 set
4. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
5. VERTICAL FIN & RUDDER -- 1 set
6. MAIN LANDING GEAR -- 1 set
MAIN WHEEL Ø95mm -- 2 pcs
COLLAR Ø4.1mm w/ set screw -- 4 sets
MOUNTING PLATE 12x20mm -- 2 pcs
SCREW PA 3x12mm -- 4 pcs
7. SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm --- 4 pcs
ENGINE MOUNT PL 5111050 -- 1 set
8. FUEL TANK 380cc PL1111380 -- 1 set
BALSA 10x15x117mm(For Fixing Fuel Tank) --1 pc.
9. SCREW PA3x14mm -- 4 pcs
STEERING ARM STAND Ø4.7mm -- 1 pc.
WOODEN 4x25x30mm (For Steering Arm Tank) --1 pc.
10. WIND SHIELD -- 1 pc.
SCREW PWA 2.3x8mm -- 5 pcs
SILICON GROMMET d1.5xD6.5mm -- 5 pcs
11. FRONT LANDING GEAR -- 1 set
FRONT WHEEL Ø95mm -- 1 pc.
COLLAR Ø4.6mm -- 3 set
STEERING ARM Ø4.6mm -- 1 set
RIGHT ANGLE WHEEL SPACER PL4121040 -- 1 set
12. SOCKET HEAD SCREW M3x30mm -- 4 pcs
WASHER d3xD7mm -- 8 pcs
M3 NUT -- 8 pcs
SPINNERØ52mm -- 1 set
THROTTLE PUSH WIRE Ø1.2x445mm -- 1 pc.
PLASTIC TUBE d2xD3x200mm -- 1 pc.
COVERING:--
LIGHTEX SGX 312 BRIGHT RED
LIGHTEX SGX 100 WHITE
LIGHTEX SGX 251 SKY BLUE
LIGHTEX SGX 351DARK BLUE
LIGHTEX SGX 313 PINK
LIGHTEX SGX 250 BLUE
P.2
13. SCREW PWA2.6x12mm -- 5 pcs
SILICON GROMMET d1.5xD6.5mm -- 5 pcs
COWLING -- 1 pc.
TRANSPARENT 3D TEMPLATE -- 1 pc.
14. SIDE WINDOWS -- 1pair
15. LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 2 sets
16. SPONGE 60x70x122mm -- 1 pc.
FUEL TUBE Ø6x5mm -- 1 pc.
STRAPER PL4112102 -- 1 pc.
WIRE Ø1x1100mm(For Rudder) -- 2 pcs
COPPER TUBE Ø2.5xD3.2x8mm --2 pcs
RIGGING Z BEND Ø1.8x27mm(For Rudder) -- 2 pcs
FRONT WHEEL PUSHROD Ø1.6x320mm -- 1 pc.
PUSH ROD Ø1.8x1155mm w/ Threads (For Elevator Servo) -- 1 pc.
17. SCREW PB2x16mm -- 2 pcs
FUEL TUBE Ø6x5mm -- 1 pc.
CLEVIS PL4112103 -- 1 pc.
HORN PL4113101 -- 1 set
18. SCREW PM2x16mm -- 2 pcs
M2 NUT -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
COPPER TUBE Ø2.5xD3.2x8mm --2 pcs
RIGGING COUPLER Ø1.8x27mm w/ Threads (For Rudder) -- 2 pcs
HORN (w/ o-Base For Rudder) PL4113101 -- 2 pcs
CLEVIS PL4112103 -- 2 pcs
19. PILOT PC001085B --1 set
PLYWOOD 3x45x122mm (For Pilot) -- 1 pc.
BALSA 6x6x45mm (For Pilot Stand) -- 2 pcs
20. SCREW PM3x30mm -- 2 pcs
WASHER d3xD12mm -- 2 pcs
PLYWOOD 3x40x120mm (For Wing Protection) --1 pc.
21. DECALS A088DEC -- 1 set
A088PO25531103

P.3
Main Wing
3
Wing Joiner(A)
12x22x346mm
Wing Joiner(B)
Ø10x180.5mm
1Main Wing
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Aileron Servo
2
PB2x20mm Screw
4
Pushrod
Ø1.8x130mm
Clevis Fuel Tube
Ø6x5mm
Aileron servo lead
Peel off shaded portion
covering film.
PB2x20mm
Horn
Bottom View
Pre-glued
1mm
TWM PL8210010
CLEVIS WRENCH
Please dry fit wing joiner into left and right wing to make sure they fit with the
proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to
both sides of all surfaces in contact. Use a stick to apply the glue to inner side
of wing joiner sleeve, and apply the glue to wing joiner before putting them
together. Wing joiner not glued properly will lead to wing failure and plane crash.
A088PO25531103

P.4
Landing Gear
6
Vertical Fin / Rudder
5
A A'
A = A'
PA3x12mm Screw
3mm Set Screw
4.1mm Collar
4
4
4
3mm Set Screw
4.1mm Collar
Main Landing Gear
Ø4mm
PA3x12mm
CC
C = C'
4Stabilizer
A A'
A = A'
(Stabilizer)
(Main Wing)
B B'
B=B'
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
Pre-glued
Pre-glued
1.5mm
A088PO25531103

P.5
Bottom View
7Engine Mount
Engine Mount
PL5111050
M4x25mm Socket Head Screw
4
4
M4x25mm
Fuel Tank
8
380cc
Fuel Tank
Install Balsa 10x15x117mm
( )For Fuel Tank Position Fixing
Fuel Tank
380cc
Front Landing Gear
9
PA3x14mm Screw
4
PA3x14mm
Steering Arm Stand
d4xD9mm Washer
d4xD9mm Washer
2mm
UP
A088PO25531103

P.6
12
M3x30mm Socket Head Screw
M3 Nut
Engine
4
8
8
M3x30mm
Plastic Tube
d2xD3x200mm
Throttle Pushwire
Ø1.2x445mm
Install Engine position
Spinner
Ø52mm
105mm
4.13 in.
Front Wheel
11
3mm Set Screw
4.6mm Collar
3
3
Collar
4.6mm
Collar
4.6mm
Collar
4.6mm
10 Canopy
PWA2.3x8mm Screw
d1.5xD6.5mm Silicon Grommet
Silicon Grommet
d1.5xD6.5mm
PWA2.3x8mm PWA2.3x8mm
5
5
Right Angle Wheel Spacer
d3xD7mm Washer
1.5mm
1.5mm
M3 Nut
d3xD7mm
Washer
d3xD7mm
Washer
A088PO25531103

P.7
Windows
14
13 Cowling
PWA2.6x12mm Screw
d1.5xD6.5mm Silicon Grommet
Trim the cowling so it
will match your engine.
PWA2.6x12mm
5
51.5mm
Silicon Grommet
d1.5xD6.5mm
1.5mm
Fuel Filler
PL8110030
A088PO25531103

P.8
Elevator Pushrod
17
PB2x16mm Set Screw
2
Elevator Pushwire
Bottom View
Elevator Horn
Line up the holes
of the horn to the
edge of the elevator
See diagram.
Fuel Tube
Ø6x5mm
Horn
PB2x16mm
Ø1mm pilot holes for World
Models tri-horn are pre-drilled.
Please look for pin-hole marks
at under side of control surfaces.
Front Wheel
11
Radio Equipment
16
Install and arrange the servo as shown in the diagram.
Rudder
Servo
Straper
Fuel Tube
Ø6x5mm
Bottom View
Plywood
9x57x122mm
Servo Set
3 x 3mm Set Screw
Linkage Connector
M2 Nut
2mm Washer
1
1
1
2
15
Please refer to attached sheet for linkage connector installation.
Included with the radio Set.
Throttle Pushwire
3x3mm Set Screw
Throttle Servo.
2mm
2mm
Washer
M2 Nut
2mm
Washer
Charge Receptacles
KP0041300
TWM PL8210010
CLEVIS WRENCH
Copper Tube
Spong
60x70x122mm
Elevator
Servo
Throttle
Servo
Press down the center
1/3 portion
Copper Tube
Rigging Z Bend
Ø1.8 x 27mm
Front Wheel Pushrod
Ø1.6x320mm
A088PO25531103

P.9
Pilot
19
PC001085B
Balsa 6x6x45mm
Plywood 3x45x122mm
18 Rudder Pullwire
PM2x16mm Screw
2
M2 Nut
PM2x16mm
2
Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please
look for pin-hole marks at side of control surfaces.
M2 Nut
2mm
TWM PL8210010
CLEVIS WRENCH
Clevis
Rigging Coupler
1.8 x 27mm
Ring
Fuel Tube
6 x 5mm
Copper Tube
A088PO25531103

P.10
20 Main Wing
d3xD12mm Washer
2
2
PM3x30mm
Wing Protection
3x40x120mm
Wing Setting
21
A A'
A = A'
B = B'
B B'
C = C'
D = D'
C C'
D D'
Adjust the wing and fuselage configuration
as shown in the diagrams.
2mm
d3xD12mm Washer
PM3x30mm Screw
A088PO25531103

Adjust the control throws as shown in
the diagram.These throws are good for
general flying. You can adjust according
to your personal preference.
Control Throws
22
Elevator
Rudder
Aileron
29mm
29mm
35mm
35mm
12mm
12mm
C.G.
23
100mm
3.94 in.
The ideal C.G. position is100 behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
mm(3.94in)
P.11
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# Super Frontier Senior is specially designed to be powered by 2C 0.46 engine, using a
more powerful engine does not mean better performance. In fact, over powered engine
may cause severe damage and injuries.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
# Check and re-tighten up all factory assembled screws, use thread locker if applicable.
C.G.
Warning!
A088PO25531103
http://www.theworldmodels.com/para/instruction/instructionManuals.php

LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Drill 2mm hole at servo horn.
Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.
A088PO25531103

Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
A088PO25531103

Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No SV4031
KP0041300
Special tool for clevis installation.
Suitable for standard and small
(EP)clevis.
Large Clevis
Small Clevis
180mm Extension
MS9111450 600 x 240 x 350 1 pc
A088PO25531103

Warbirds
Scale
Sports
Trainer
DuctedFan Pattern
Funfly
Electric
Glider
Boat
Accessories
Covering
(Lightex / Toughlon)
The World Models
www.theworldmodels.com
Manufacturing Co., Ltd.
A088PO25531103