Dancing Wings Hobby Fokker Dr.I User manual

A
B
C
E F
G
H
D2
D1 D3
IJ
T
K
LM
S
R1 R2
Q
P1
P2
N O
P1
A
Fokker Dr.I
Instruction Manual
1.Install landing gear bracket P1, embed the bracket
into the prefrmed groove,lock it with self-tapping screw
and M spacer.
2.Install landing gear aileron and wheels.
3.Plug the middle wings into each other with carbon
rod,glue the joint.
4.Plug the middle wing's bolt into the fuselage, then
lock the wing with self-tapping screw.
5.Plug the upper wings into each other with carbon
rod, glue the joint.
6.Install wing bracket in the back of the upper wing,
lock it with self-tapping screw.
7.Use self-tapping screw to lock the other end of
bracket on the fuselage. 8.Install wing's support rods as shown.
9.Plug lower wings into each other with carbon rod,
glue the joint.
10.Use self-tapping screw to lock the lower wing on
the fuselage.
11.Support rods connect the lower wing, adjust the
space among the three wings and fasten them.
12.Install motor board, and install the emulational
engine on the motor board.Install emulational
machine gun on the middle wing. (Don't stick the
motor board on the fuselage at this moment, please
stick the motor board on the fuselage after finishing
the motor installation.)
13.Install the cowling, fasten the edge with 3pcs
self-tapping screws.
14.Install horizontal tail, connect with fuselage groove,and
fix it with glue.Connect the vertical tail to the tail of fuselage
with paper hinge, and make the vertical tail swing freely.
C
T
P2
T
Lock the wheels
P2
P1
Fasten it with screw
Short
Long R2
R1
D1
D3
D2
O
I
Q
HB
Specification
Wingspan：770mm
Length：630mm
Net weight：≈650g
Suggested Equipment
Motor： 2212 800-1000KV
ESC：20A
Servo：2.5g *2 & 5g *2
Propeller：7-8 inch
Battery：2-3S 1300-1800mAh
Radio≥3CH
A:Fuselage B:Vertical tail C:Landing gear aileron D1-3:Wing
E:Screw set, quick connector, wheel lock
F:Emulational machine gun G:Sled H:Horizontal tail
I:Emulational engine J:Rudder angle K:Paper hinge
L:Carbon rod M:Spacer N:Wheel bracket O:Motor board
P1-2:Landing gear steel wire Q:Cowling R1-2:Wing bracket
S:Sticker T:Wheel
Fasten it with screw
Here M spacer
is for cabin
cover,you can
open and close
it freely.

15.Take down rudder angle from J board,install into
elevator and rudder, glue it, and connect rudder angle
with Z-shape steel wire.
16.Power system installation as shown.
K Paper hinge
K Paper hinge
J
J
Install the motor on the
motor board, fasten with
screw, then glue the motor
board on the fuselage.
Fasten the landing gear bracket on
the wooden box with self-tapping
screws according to the actual
distance during static show.
Motor installation
Install elevator,rudder servo, and link the steel wire
pulling rod in the fuselage.
Fasten propeller to the motor
with prop adapter.
19.Static show
18.Stick the sticker S after finishing installation.
N
N
17. Adjust the C.G
125mm
C.G
Install servo on the upper wing's servo place as shown.
Install rudder angle on the aileron.Connect rudder arm
and rudder angle with steel wire pulling rod.