The world models manufacturing Ultimate

INSTRUCTION MANUAL

Wing Span

Wing Area

Flying Weight

Fuselage Length

42.0 in / 1060 mm

578 sq in / 37.3 sq dm

4.5 lbs / 2050 g

39.5 in / 1000 mm

Specifications

Warning !This model is not a toy.

It is designed for maximum performance. Please seek advice if one is not familiar with this kind

of engine powered precision model. Operating this model without prior preparation may cause

injuries. Remember, safety is the most important thing. Always keep this instruction manual at

hand for quick reference.

0.48 cu.in. displacement 4-stroke-0.56

R s 4 radiow/3standardservos

and1miniservo

equire : -channel

* Specifications are subject to change without notice.*

0.40-0.46 cu.in. displacement 2-stroke

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

A009SPO26741109

P.1

P. 3 -11

Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT

and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you

find to be defective after the gluing process may be difficult to remove for warranty replacement. The

manufacturer will replace any defective parts, but will not extend to the parts that are good before

gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.

INDEX

BEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

P. 1

P. 2

P.11

BEFORE YOU BEGIN

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual comprise of the following : -

3mm

Do not overlook this symbol!

Cut off shaded portion.

Peel off shaded portion

covering film.

Pay close attention here!

Pierce the shaded portion

covering film.

Must be purchased separately!

Drill holes with the specified

diameter (here: 3mm).

Ensure smooth non-binding

movement while assembling.

Apply instant glue

(C.A.glue, super glue.)

Assemble left and right

sides the same way.

Apply epoxy glue.

Apply thread locker

Warning!

A009SPO26741109

Parts List

COVERING:--

PURPLE COLOR SCHEME:

TOUGHLON STL 100 WHITE

TOUGHLON STL 201 BLACK

TOUGHLON STL 561 PEARL PURPLE

TOUGHLON STL 370 SILVER

YELLOW COLOR SCHEME:

TOUGHLON STL 100 WHITE

TOUGHLON STL 201 BLACK

TOUGHLON STL 330 CADMIUM YELLOW

TOUGHLON STL 370 SILVER

P.2

1. MAIN WING (Lower) --1 pair

2. PLYWOOD 5x28x48mm (For Aileron Servo) -- 1 pc.

RING Ø2.3mm PL4112023 -- 2 pcs

3. PUSHROD Ø1.8x70mm w/ Threads (For Aileron) -- 2 pcs

FUEL TUBE Ø6x5mm -- 4 pcs

STRAPER PL4112102 -- 2 pcs

CLEVIS PL4112103 -- 2 pcs

4. MAIN WING (Upper) -- 1 set

5. FUSELAGE -- 1 pc.

STABILIZER & ELEVATOR -- 1 set

6. VERTICAL FIN & RUDDER -- 1 set

7. TAIL LANDING GEAR PL7100001 -- 1 set

COLLAR Ø2.1mm w/ set screw -- 1 set

TALL WHEEL Ø25mm -- 1 pc.

SCREW PA3x12mm -- 2 pcs

8. PUSHROD Ø1.8x465mm w/ Threads (For Elevator) -- 2 pcs

SCREW PB2x12mm -- 4 pcs

FUEL TUBE Ø6x5mm -- 2 pcs

CLEVIS PL4112103 -- 2 pcs

HORN PL4113101 -- 2 sets

9. PUSHROD Ø1.8x535mm w/ Threads (For Rudder) -- 1 pc.

SCREW PB2x12mm -- 2 pcs

FUEL TUBE Ø6x5mm -- 1 pc.

CLEVIS PL4112103 -- 1 pc.

HORN PL4113101 -- 1 pc.

10. MAIN WING GEAR Ø2.5mm HW2402292 -- 1 set

MAIN WHEEL Ø58mm -- 2 pcs

WHEEL PANTS PC198WWPA -- 1 pair

COLLAR 4.1mm w/ set screw -- 4 sets

SCREW KA2.3x8mm -- 4 pcs

SOCKET HEAD SCREW HM4x35mm -- 2 pcs

SOCKET HEAD SCREW M3x16mm -- 3 pcs

QUICK RELEASE NYLON RIVET d2xD8mm PL1208042-- 4 pcs

WASHER d3xD7mm -- 3 pcs

WASHER d4xD9mm -- 4 pcs

M4 NUT -- 2 pcs

PLATE 1mm -- 1 pair

11. ENGINE MOUNT PL5111050 -- 1 set

SOCKET HEAD SCREW M4x25mm -- 4 pcs

WASHER d4xD9mm -- 4 pcs

12. FUEL TANK 260cc PL1111260 -- 1 set

DOUBLE-SIDED TAPE 40x100mm -- 1 pc.

TABLE TIE (FOR FUEL TANK) 1.5x5x400mm -- 1 pc.

13. LINKAGE CONNECTOR Ø2.1mm HW7111060 -- 1 set

14. SOCKET HEAD SCREW M3x25mm -- 4 pcs

WASHER d3xD7mm -- 8 pcs

M3 NUT -- 8 pcs

THROTTLE PUSHWIRE Ø1.2x300mm -- 1 pc.

PLASTIC TUBE d2xD3x200mm -- 1 set

15. PUSHROD CONECTOR 4x9x20mm PL4410010 -- 1 set

PUSHROD Ø1.8x70mm (For Elevator Servo) -- 1 pc.

PLYWOOD 3x100x103mm (For Fuselage Servo) -- 1 pc.

BALSA 5x5x97mm (For Fueslage Servo Stand) -- 2 pcs

STRAPER PL4112102 -- 2 pcs

FUEL TUBE Ø6x5mm -- 2 pcs

SPONGE 10x80x200mm (For Radio Equipment) -- 2 pcs

16. CANOPY -- 1 set

PILOT PC001050A/PC001050B -- 1 pc.

DOUBLE-SIDED TAPE 8x500mm -- 1 pc.

SCREW PWA2.3x8mm -- 4 pcs

SILICON GROMMET d1.5xD6.5mm -- 4 pcs

17. COWLING -- 1 set

TRANSPARENT 3D TEMPLATE -- 1 pc.

SPINNER Ø57m PL2111057 -- 1 pc.

SCREW PWA2.6x12mm -- 4 pcs

SILICON GROMMET d1.5xD6.5mm -- 4 pcs

18. SOCKET HEAD SCREW HM4x25mm -- 1 pc.

WASHER d4xD15mm -- 1 pc.

19. SOCKET HEAD SCREW M3x30mm -- 1 pc.

SOCKET HEAD SCREW M3x20mm -- 1 pc.

SCREW PM3x12mm -- 8 pcs

SCREW PM2x8mm -- 2 pcs

SCREW PA3x12mm -- 4 pcs

WASHER d3xD7mm -- 18 pcs

M2 NYLON INSERT LOCK NUT -- 2 pcs

M3 NYLON INSERT LOCK NUT -- 10 pcs

PLYWOOD 4x143x181mm (Side Cabane) -- 2 pcs

PLYWOOD 3x236x230mm (Wing Incidence Angle Template) -- 2 pcs

ALUMINUM PLATE (Brace:Fueslage to Wing) -- 1 set

20. SCREW PB2x12mm -- 8 pcs

HORN PL4113101-- 4 sets

CLEVIS PL4112103 -- 4 pcs

PUSHROD Ø1.8x145mm w/ Threads (For Aileron to Aileron) -- 2 pcs

FUEL TUBE Ø6x5mm -- 4 pcs

21. DECALS: A009SDEC -- 1 set

A009SPO26741109

P.3

Aileron Servo (Lower)

1Main Wing (Lower)

Apply instant type CA glue to both sides of each hinge.

Ring

Plywood

5x28x48mm

Aileron Servo (Lower)

Straper

Fuel Tube

Ø6x5mm

Clevis

Pushrod

Ø1.8x70mm

Completed

CABANE MOUNTCABANE MOUNT

1mm

TWM PL8210010

CLEVIS WRENCH

A009SPO26741109

P.4

Stabilizer & Elevator

4Main Wing (Upper)

Apply instant type CA glue to both sides of each hinge.

Vertical Fin & Rudder

Completed

Bottom View

Completed

Apply instant type CA glue to both sides

of each hinge.

A=A

C=C

(Stabilizer)

(Main Wing)

B B'

B=B'

Temporary install the main wing, adjust

leveling of the stabilizer to make it as

parallel to the main wing as possible.

Apply instant type CA glue to both sides of each hinge.

Completed

CABANE MOUNTCABANE MOUNT

A009SPO26741109

P.5

Tail Landing Gear

Rudder Pushrod

PA3x12mm Screw

2.1mm Collar

M3x3mm Set Screw

PA3x12mm

2.1mm Collar

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

Bottom View

8Elevator Pushrod

PB2x12mm Screw

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

Bottom View

≈120mm

≈46mm

≈90mm

≈28mm

2mm

PB2x12mm Screw

TWM PL8210010

CLEVIS WRENCH

PB2x12mm

Fuel Tube

Ø6x5mm

Pushrod

Ø1.8x465mm

Clevis

Horn

PB2x12mm

Fuel Tube

Ø6x5mm

Clevis

Pushrod

Ø1.8x535mm

TWM PL8210010

CLEVIS WRENCH

A009SPO26741109

P.6

12 Fuel Tank

Engine Mount

d4xD9mm Washer

d4xD9mm

Washer

Engine Mount

PL5111050

Main Landing Gear

M3x16mm

Bottom View

Apply thread locker.

Blind nuts are off-centered to keep

the spinner at the fuselage axis.

M4x 25mm Socket Head Screw

M4x 25mm

Socket Head Screw

HM4x 35mm

d4xD9mm Washer

M4 Nut

M3x3mm Set Screw

4.1mm Collar

Plate 1mm

Completed

M3x16mm Screw

M4 Nut

4.1mm Collar

d4xD9mm Washer

HM4x35mm Screw

KA2.3x8mm Screw

d3xD7mm Washer

Fuel Tank

260cc

d2XD8mm

Quick Release Nylon Rivet

Completed

A009SPO26741109

d3xD7mm Washer

P.7

Engine

M3x25mm SocketHeadScrew

M3 Nut

d3xD7mm Washer

M3x25mm

M3 Nut

Throttle Pushwire Ø1.2x300mm

Plastic Tube d2xD3x200mm

115mm

4.5 in.

Installed Engine Position

d3xD7mm

Washer

Servo Set

3x3mm Set Screw

Linkage Connector

M2 Nut

2mm Washer

Please refer to the attached sheet for linkage connector installation.

Throttle Pushwire

Throttle Servo.

2mm

Washer

M2 Nut

2mm

Washer

Included with the radio Set.

3x3mm Set Screw

A009SPO26741109

Sponge

PLYWOOD

3x100x103mm

BALSA

5x5x97mm

Straper

Fuel Tube

Ø6x5mm

Throttle Pushwire

Ø1.2x280mm

Rudder Pushrod

Ø1.8x550mm

BALSA

5x5x97mm

Throttle Servo

Rudder Servo

Front

17 Cowling & Spinner

PWA2.6 X 12mm Screw

16 Canopy

First insert the grommet to the canopy then apply screw.

PWA2.3x8mm Screw

d1.5xD6.5mm Silicon Grommet

Pilot

15 Radio Equipment

Spinner Ø57mm

d1.5xD6.5mm

Silicon Grommet

PWA2.3x8mm

Apply double-sided tape

Install and arrange the servo as shown in the diagram.

Decals

1.5mm

Please refer to the attached sheet for usage

of the transparent 3D template.

First insert the

grommet to the

cowling then

apply screw.

J2(Pushrod Ø1.8x440)

J1(Pushrod Ø1.8x95)

KM2x8mm

M2 Nut

Elevator Pushrod

Ø1.8x70mm

Elevator Servo

Pushrod

Connector

P.8

Fuel Filler

PL8110030

Charge Receptacles

KP0041300

d1.5xD6.5mm Silicon Grommet

A009SPO26741109

PWA2.6x12mm

Silicon Grommet

d1.5xD6.5mm

Cowling

Fuselage

P.9

18 Main Wing (Lower)

HM4x25mm Socket Head Screw

d4xD15mm Washer

HM4x25mm

Bottom View

PLYWOOD 3x236x230mm

40mm

94mm

PLYWOOD 4x143x181mm

SIDE CABANE

WING INCIDENCE ANGLE TEMPLATE

d4xD15mm Washer

M3x30mm M3x20mm

d3xD7mm

Washer

M3 Nylon

Insert Lock Nut

d3xD7mm

Washer

M3 Nylon

Insert Lock Nut

PM2x8mm

M2 Nylon Insert

Lock Nut

2mm

19 Main Wing

PM3x12mm Screw

d3xD7mm Washer

M2 Nylon Insert Lock Nut

M3x30mm Socket Head Screw

M3x20mm Socket Head Screw

PA3x12mm Screw

Outer wing cabane

should fit to the outside

of outer wing cabane

mounts.

With the wing incidence angle

template still in place, position

the side cabanes, mark and drill

the side cabane mounts and

fasten with PM3x12mm screw

and nut.

M3 Nylon Insert Lock Nut

PM2x8mm Screw

Pierce the two pre-drill holes at

upper wing center line and fasten

the center cabanes with PM3x20mm

& PM3x30mm screw and nut. With

the lower wing fastened to the

fuselage, insert the wing incidence

angle templates to both sides of

upper and lower wing to hold the

upper wing in position. Mark and

drill 2mm pilot holes at the fuselage

and fasten the center cabane with

PA3x12 mm screws.

PA3x12mm

Front

Please install in

correct direction

M3 Nylon Insert

Lock Nut

d3xD7mm

Washer d3xD7mm

Washer

PM3x12mm

3mm

A009SPO26741109

BB'

CC'

DD'

P.10

21 Wing Setting

20 Main Wing

A=A' B=B' C=C' D=D' E=E' F=F'

F F'

G=G'

G G'

E E'

AA'

PB2x12mm Fuel Tube

Ø6x5mm

Clevis

Horn

Pushrod

Ø1.8x145mm

Main Wing (Upper)

Main Wing (Lower)

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

PB2x12mm Screw

A009SPO26741109

P.11

Adjust the control throws as shown in the diagram.

These throws are good for general flying. You can

adjust according to your personal preference.

Elevator

Rudder

Control Throws

Ailerons

5mm

30mm

10mm

C.G.

81mm

3 2 in..

The ideal C.G. position is 81mm (3 2 in.) behind

the leading edge measured at top wing center line.

In order to obtain the C.G. specified, add weight to

the fuselage or move the battery position. Check

the C.G. before flying.

Important Safety Precautions

Warning!

# First time flyer should never fly by himself / herself. Assistance from experienced

flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly

pre-adjusted aircraft.

# is specially designed to be powered by

engine, using a more powerful engine does not mean better performance. In fact,

over powered engine may cause severe damage and injuries.

# Make sure the air field is spacious, never fly the plane too close to people and never

get too close to a running propeller.

# If you find wrinkles on the covering as a result of weather changes, you can use hot

iron to remove the wrinkles. Please begin with lower temperature setting and

gradually raise the temperature until the wrinkles are gone. Too hot an iron may

damage the covering. Don't use hot iron near the seams or edges, hot iron will

melt the glue and shrink the covering at the same time, causing the seams to pull away.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

2C 0.40-0.46 or 4C 0.48-0.56

http://www.theworldmodels.com/para/instruction/instructionManuals.php

A009SPO26741109

Product Registration Form (US Customers)

We would like to share with you any relevant information regarding your model, including

product news and free upgrade parts when applicable. Please fill in the following and send to

AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA.

1. Name:

2. Address:

3. Phone #: E-mail:

4. Model:

Wing QC# Fuselage QC#

(QC numbers are stamped on wing and fuselage)

5. Date of Purchase:

6. Store Name:

Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.

Thank you very much for purchasing our product.

LINKAGE CONNECTOR

HW7111050 & HW7111060

After fastening the round nut, make sure that

the linkage connector can rotate freely.

Drill 2mm hole at servo horn.

Insert linkage connector

into servo horn.

Make sure shoulder of

screw is cleared from

servo horn.

Add washer to reduce

play if necessary.

Shoulder

Tighten up the round nut

against the shoulder. Apply

CA or permanent thread

locker.

A009SPO26741109

Usage of the transparent 3D template

This transparent 3D template

is used for position guidance

of the actual cutting of the

pre-painted cowling.

Simply cut the transparent 3D template to fit your engine and

exhaust pipe, then slide onto the actual cowling and use as

template to mark the openings required for final cutting.

A009SPO26741109

Code No.Size Package

Code No SV4031

KP0041300

Special tool for clevis installation.

Suitable for standard and small

(EP)clevis.

Large Clevis

Small Clevis

180mm Extension

A009SPO26741109