The World Models Manufacturing Super Stunts 60 User manual

Wing Span
Wing Area
Flying Weight
Fuselage Length
80 in / 2030 mm
1337 sq in / 86.3 sq dm
8.0 lbs / 3550 g
68.5 in / 1740 mm
Warning !This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
0.6 cu. in. displacement 2-stroke0-0.75
Requires : 4 channel radio w 5 standard servos - /
* Specifications are subject to change without notice.*
Specifications
INSTRUCTION MANUAL
E
A
D
R
-
Y
T -
T
S
O
O
-
F
M
L
L
Y
A
Super Stunts 60

Super Stunts 60
P. 1
P. 3 - 11
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts. but will not extend to the parts that are good before
gluing to defective parts during assembly.
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P. 11
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
3mm
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
Apply thread locker
Warning!

Parts List
P. 2
1.MAIN WING -- 1 pair
2.SCREW PB2x20mm -- 8 pcs
FUEL TUBE Ø6x5mm -- 8 pcs
STRAPER -- 4 pcs
CLEVIS -- 4 pcs
HORN -- 4 sets
PUSHROD Ø1.8x165mm w/Threads(For Aileron&Flap Servo) -- 4 pcs
3.SCREW PA3x30mm -- 1 pc.
SCREW PM3x30mm -- 1 pc.
WASHER d3xD12mm -- 2 pcs
WING TUBE Ø25.4x516mm -- 1 pc.
4.STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
SCREW PM3x22mm -- 3 pcs
WASHER d3xD7mm -- 3 pcs
BALSA(Fin Tip)6x245mm -- 1 pc.
5.VERTICAL FIN & RUDDER -- 1 set
6.FUEL TANK 380cc -- 1 set
BALSA 10x10x109mm(For Fixing Fuel Tank) -- 1 pc.
7.ENGINE MOUNT PL5111070 -- 1 set
SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm -- 4 pcs
8.WOODEN 6x9x18mm(For Front Landing Gear) -- 1 pc.
9.FRONT LANDING GEAR -- 1 set
WHEEL Ø70mm -- 1 pc.
COLLAR Ø4.1mm w/set screw -- 3 sets
STEERING ARM Ø4.1mm w/set screw -- 1 set
FRONT WHEEL PUSHWIRE Ø1.6x490mm -- 1 pc.
PLASTIC TUBE d2.5xD4x420mm -- 1 pc.
10.MAIN LANDING GEAR -- 1 set
SCREW PA3x12mm -- 4 pcs
MOUNTING PLATE 12x20mm -- 2 pcs
11.MAIN WHEEL Ø70mm -- 2 pcs
COLLAR Ø4.1mm w/set screw -- 4 sets
12. M4x30mm -- 4 pcs
WASHER d4xD9mm -- 8 pcs
M4 NUT -- 8 pcs
SPINNER Ø62mm -- 1 pc.
THROTTLE PUSHWIRE 1.2x370mm -- 1 pc.
P
L A STIC TUBE d2xD3x220mm -- 1 pc.
13.PLYWOOD 3x61x117.5mm(For Throttle Servo) -- 1 pc.
BALSA 8x8x61mm(For Throttle Servo Stand) -- 2 pcs
14.LINKAGE CONNECTOR Ø2.1mm -- 2 sets
15.SCREW PM2x16mm -- 2 pcs
M2 NUT -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
CLEVIS -- 2 pcs
HORN(Non-Basa)(For Rudder) -- 2 sets
RIGGING C0UPLER Ø1.8x27mm w/Threads(For Rudder) -- 2 pcs
COPPER TUBE d2.5xD3.2x8mm(For Rudder Servo) -- 4 pcs
WIRE Ø1x1000mm(For Rudder) -- 2 pcs
16.SCREW PB2x16mm -- 2 pcs
FUEL TUBE Ø6x5mm -- 1 pc.
HORN -- 1 set
CLEVIS -- 1 pc.
PUSHROD Ø1.8x920mm w/Threads(For Elevator) -- 1 pc.
17.SPONGE 10x80x200mm(For Radio Equipment) -- 2 pcs
STRATER-- 1 pc.
RIGGING Z BEND Ø1.8x27mm(For Rudder Servo) -- 2 pcs
COPPER TUBE d2.5xD3.2x8mm -- 2 pcs
FUEL TUBE Ø6x5mm -- 1 pc.
PLYWOOD 6x37x116mm(For Elevator &Rudder Servo) -- 2 pcs
BALSA 6x8x37mm(For Elevator &Rudder Servo Stand) -- 4 pcs
18.SOCKET HEAD SCREW M4x40mm -- 2 pcs
WASHER d4xD15mm -- 2 pcs
PLYWOOD 3x40x116mm(Wing Protection) -- 1 pc.
19.DECALS:A098DEC -- 1 set
SOCKET HEAD SCREW
TOUGHLON:--
TOUGHLON STL 100 WHITE
TOUGHLON STL 201 BLACK
TOUGHLON STL 310 RED
TOUGHLON STL 351 DARK BLUE

P.3
Main Wing
3
1Main Wing
PA3x30mm Screw
d3xD12mm Washer
PA3x30mm
Washer d3xD12mm
Wing Tube
Ø25.4x516mm
PM3x30mm
Aileron & Flap Servos
2
PB2x20mm Screw
Pushrod
Ø1.8x165mm Straper
Fuel Tube
Ø6x5mm
Lead for servo
wire Provided
Bottom View
Step 1. Insert the aluminum wing tube with the pre-drilled hole end into the right wing. Align
the lines marked at the wing root and wing tube, then apply the PM3x30mm machine screw
through the pre-drilled hole on top of the wing. ( please confirm the alignment of the hole by
putting a 2.5mm diameter rod through the pre-drilled wing hole before applying the screw )
The hole on the wing tube is pre-threaded, do not over tighten the PM3 screw, the set up is for
future removal of the wing.
Note : It is recommended that the wing tube stays with the left wing.
Removal of the wings could be achieved by removing the right wing
machine screw, the right wing then the left wing with wing tube. If removal
of wing tube from left wing is also required, it is recommended that instead
of applying self-tapping screw in step 2, you pre-tap with M3 thread cutter and
apply M3 machine screw.
Step 2. Install the right wing to the left wing. Locate
the pre-drilled 2.5mm hole at top of left wing, and drill
along with 2.5mm drill bit until it passes through the
Wing tube. Apply the PA3x30mm self-tapping screw.
Washer d3xD12mm
Apply instant type CA glue to both sides of each hinge.
PM3x30mm Screw
1
1
PB2x20mm
Clevis
Fuel Tube
Ø6x5mm
TWM PL8210010
CLEVIS WRENCH
2.5mm
Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please
look for pin-holemarks at under side of control surfaces.

P.4
4
Vertical Fin/Rudder
5
Stabilizer & Elevator
PM3x22mm Screw
d3xD7mm Washer
PM3x22mm
d3xD7mm
Balsa
6x245mm
Temporary install the main wing, adjust
leveling of the stabilizer to make it as
parallel to the main wing as possible.
(Stabilizer)
(Main Wing)
BB'
B=B'
Bottom View
Apply instant type CA glue to both sides of each hinge.
Apply instant type CA glue to both sides of each hinge.
C=C'
C C

P.5
6
Front Landing Gear
8
Engine Mount
7
Fuel Tank
Fuel Tank 380cc
Fuel Tank Setup
Fuel Tank
380cc
Top View
M4x25mm Socket Head Screw
d4xD9mm Washer
Engine Mount
PL5111-070
Washer
d4xD9mm
M 4x25mm
Blind nuts are off-centered to keep
the spinner at the fuselage axis.
Apply thread locker to screws
Wooden
6x9x18mm
Balsa 10x10x109mm
(For ixing )Fuel Tank Position F
UP

P.6
9
Landing Gear
11
Landing Gear
10
Front Wheel
3mm Set Screw
4.1mm Collar
PA3x12mm Screw
PA3x12mm
3mm Set Screw
4.1mm Collar Wheel Ø70mm
Main Landing Gear
Ø4mm
4.1mm Collar
3mm Set Screw
2mm
Ø1.6x490mm(Frint wheel Pushrod)
3mm Set Screw
Front View
Wheel mmØ70
3mm Set Screw
Completed
3mm Set Screw

P.7
12
Servo Set
14
Throttle Servo
13
Engine
Linkage Stopper
3 X 3mm Set Screw
L i n k a g e C o n n e c t o r
2mm Nut
2mm Washer
d4xD9mm Washer
M4 Nut
Plastic tube
d2xD3x220mm
M4x30mm
Throttle Pushwire
Ø1.2x370mm
IIIustration is for upright mounting.
You can mount the engine inverted
simply by rotating the engine mount.
Thrust angles will not be affected.
Install Engine position
Spinner
Ø62mm
136mm
5.35in.
d4xD9mm
Washer
d4xD9mm
Washer
Plywood
3x57x117.5mm
Balsa
8x8x61mm
M4 Nut
Please refer to attached sheet for linkage connector installation.
Included with the radio Set.
Throttle Pushwire
3x3mm Set Screw
Throttle Servo.
2m m
2mm
Washer
M2 Nut
2mm
Washer
Fuel Filler
PL8110030
M4x mm 30 Socket Head Screw

P.8
Rudder Pullwire
15
Fuel Tube
PM2x16mm Screw
2mm Nut
PM2x16mm
2mm Nut
16 Elevator Pushrod
PB2x16mm Screw
Pushrod
Ø1.8x920mm
PB2x16mm
Fuel Tube
Ø6x5mm
Horn
Copper Tube
d2.5xD3.2x8mm
Ø 1mm pilot holes for World Models
tri-horn are pre-drilled. Please look
for pin-holemarks at side of control
surfaces.
RIGGING COUPLER
Ø1.8x27mm
2mm
Ø 1mm pilot holes for World Models tri-horn
are pre-drilled. Please look for pin-holemarks
at under side of control surfaces.
Ø6x5mm

P.9
Main Wing
18
d4xD15mm Washer
M4x40mm
d4xD15mm
Wing Protection
3x40x116mm
17 Radio Equipment
Install Pinch the servo as shown in the diagram.
Throttle
Pushwire
Throttle
Servo
Rudder
Servo
Elevator
Servo
Top View
Front
Charge Receptacles
KP0041300
Plywood
6x37x116mm
Plywood
6x37x116mm
Balsa
6x8x37mm
Copper Tube
Press down the center
1/3 portion
Balsa
6x8x37mm
4mm
M4x mm 40 Socket Head Screw

P.10
19
C.G.
21
Control Throws
20
Setting Wing Adjust the wing and fuselage configuration
as in the diagrams.
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
The ideal C.G. position is 125mm (4.92in) behind
the leading edge measured at where the wing
meets the fuselage.In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
125mm 4.92in.
Elevator
15mm
15mm
Aileron
10mm
10mm
Rudder
43mm
43mm
C.G.

P.11
Important Safety Precautions
A098PO22120911
Warning!
# Fi r st t i me f l ye r s ho u l d n e ve r f ly b y h im s el f / h e r s el f . A s s is t an c e fr o m e x p e r i en c ed
fl y er i s a bs o lu t e l y n ec e s s ar y.
# Pr e -f l i g ht a d j u s tm e nt m u st b e d on e b e f o re f l yi n g, i t i s v e r y d an g e r ou s t o f l y a b a dl y
pr e -a d j u st e d ai r cr a ft .
# is specially designed to be powered by 2 C 0 . 6 0 -0 . 75
en g i n e, u s in a m o r e p o w e rf u l en g in e d oe s n ot m e a n be t te r p er f or m a n c e . I n f ac t , ov e r
powered engine may cause severe damage and injuries.
# Ma k e su r e th e a ir f i e l d i s s pa c i o us , n e v e r f l y t h e pl a n e to o c l o s e t o pe o p l e a n d ne v e r
ge t t oo c l os e t o a r un n i n g p ro p e l le r.
# If y o u f i n d w r i nk l es o n t h e co v er i ng a s a r e su l t of we a t h e r c h a ng e s, y o u c a n u s e ho t
ir o n to re m o v e t h e wr i nk l es . P le a se b e gi n w it h l ow e r te m pe r a t ur e s e t t in g a nd
gr a d u al l y ra i se th e t em p e r at u re u n ti l t he w r in k le s a re g o ne . To o h o t an i r on m a y
da m a g e t h e c o v e r i n g. D o n' t u se h o t i r o n n ea r t he s e am s o r ed g es , h ot i r on w i ll
me l t th e g lu e a nd s h r i n k t h e c o v e ri n g a t t h e s am e t im e , ca u s i n g t h e s e a m s t o pu l l a wa y.
# Ch e ck a n d re - ti g ht e n up al l f a ct o r y a s s e mb l ed s c re w s, u s e th r ea d l oc k er i f n ec e ss a r y.
S u p e r S t u n t s 6 0

LINKAGE CONNECTOR
HW7111050 & HW7111060
After fastening the round nut, make sure that
the linkage connector can rotate freely.
Drill 2mm hole at servo horn.
Insert linkage connector
into servo horn.
Make sure shoulder of
screw is cleared from
servo horn.
Add washer to reduce
play if necessary.
Shoulder
Tighten up the round nut
against the shoulder. Apply
CA or permanent thread
locker.

Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 2403 Research Drive, Livermore, CA 94550 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.

Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No.Size Package
Code No SV4031
KP0041300
Special tool for clevis installation.
Suitable for standard and small
(EP)clevis.
Large Clevis
Small Clevis
180mm Extension

The World Models
Manufacturing Co., LTD.
www.theworldmodels .com
Warbirds
Scale
Sports
Trainer
DuctedFan Pattern
Funfly
Electric
Glider
Boat
Accessories
Covering
(Lightex / Toughlon)
A098PO22120911