The World Models Manufacturing SUPER CHIPMUNK-EP User manual

Wing Span 39.5 in / 1000 mm
Wing Area
Flying Weight
Fuselage Length
25.5 oz / 720 g
260 sq in / 16.8 sq dm
32.0 in/ 810 mm
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of electric powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
*Specifications are subject to change without notice.*
INSTRUCTION MANUAL
Specifications
E
A
D
R
-
Y
T -
T
S
O
O
-
F
M
L
L
Y
A
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF) SERIES
MADE IN CHINA
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
E205PO11571111
Requires: 4-channel radio w/ 4 micro servos,
Outrunner Motor KM0283010
w/ Propeller Adaptor HW2340100
20A brushless ESC, 3 cells 11.1V
2100 mAh Li - Po battery & charger.

P.1
Apply thread locker
Apply epoxy glue.
Pierce the shaded portion
covering film.
Appl
(C.A.glue, super glue.)
y instant glue
Ensur
movement while assembling.
e smooth non-binding
Do not overlook this symbol !
P. 3 -9
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts, but will not extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P.9
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
1
2
3
Assembl
sides the same way.
e left and right
Pee
covering film.
l off shaded portion
Drill holes with the specified
diameter (here:3mm).
Pay close attention here!
Cut off shaded portion.
Must be purchased separately !
Warning!
3mm
E205PO11571111

Parts list
P.2
COVERING:--
LIGHTEX SGX E205
LIGHTEX SGX 310 RED
LIGHTEX SGX 350 CORSAIR BLUE
LIGHTEX SGX 100 WHITE
1. MAIN WING -- 1 pair
2. PUSHROD Ø1.4X75mm w/ Thresds (For Aileron) -- 2 pcs
STRAPER PL4112106 -- 2 pcs
SCREW PM2x12mm -- 4 pcs
CLEVIS PL4112105 -- 2 pcs
FUEL TUBE D4xd2x4mm -- 4 pcs
HORN PL4113102 -- 2 sets
3. STABILIZER & ELEVATOR -- 1 set
FUSELAGE -- 1 pc.
4. TAIL LANDING GEAR -- 1 set
SCREW PA2x8mm -- 2 pcs
VERTICAL FIN & RUDDER -- 1 set
5. PUSHROD Ø1.4x430mm w/ Threads (For Elevator) -- 2 pcs
SCREW PM2x8mm -- 4 pcs
CLEVIS PL4112105 -- 2 pcs
FUEL TUBE D4xd2x4mm -- 2 pcs
HORN PL4113102 -- 2 sets
6. PUSHROD Ø1.4x400mm w/ Threads (For Rudder) -- 1 pc.
CLEVIS PL4112105 -- 1 pc.
SCREW PM2x8mm -- 2 pcs
HORN PL4113102 -- 1 set
FUEL TUBE D4xd2x4mm -- 1 pc.
7. SOCKET HEAD SCREW M3x6mm -- 4 pcs
SCREW PM2x12mm -- 2 pcs
SCREW PWA2x8mm -- 4 pcs
WASHER d3xD7mm -- 4 pcs
COWLING -- 1 pc.
SPINNER Ø36mm SP26036FR0 -- 1 pc.
FOLDING PROPELLER SET PL6314020 -- 1 set
8. PUSHROD CONNECTOR PL4410020 -- 1 set
BATTERY TIE -- 1 pc.
SPONGE -- 1 pc.
DOUBLE-SIDED TAPE -- 1 pc.
FUEL TUBE D4xd2x4mm -- 2 pcs
PUSHROD Ø1.4x80mm (For Elevator Servo) -- 1 pc.
STRAPER PL4112106 -- 2 pcs
9. SCREW PM2.5x20mm -- 2 pcs
WASHER d2.5xD8mm -- 2 pcs
10. MAIN LANDING GEAR -- 1 pc.
SCREW PA2.3x12mm -- 4 pcs
COLLAR Ø2.6mm w/ set screw -- 2 sets
LANDING WIRE STRAPS 12x27mm PL4114030 -- 2 pcs
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
11. CANOPY -- 1 pc.
SCREW PWA2x8mm -- 4 pcs
PILOT PL101042A -- 1 pc.
12. DECALS E205DEC -- 1 set
E205PO11571111

P.3
Aileron Servos
2
PM2x12mm Screw
4
Ø1mm pilot holes for World Models
tri-horn are pre-drilled. Please look
for pin-hole marks at under side of
control surfaces.
PM2x12mm
Pushrod
Clevis
2mm
Horn
Fuel Tube
Ø4x4mm
straper
1mm
Ø1.4x75mm
Bottom View
Main Wing
1
Apply instant type CA glue to both sides of each hinge.
Bottom View
Aileron Servo lead
TWM PL8210010
CLEVIS WRENCH
E205PO11571111

4
P.4
Vertical Fin/Rudder & Tail Landing gear
Stabilizer & Elevator
3
Temporary install the main wing, adjust leveling of
the stabilizer to make it as parallel to the main wing
as possible.
(Stabilizer)
(Main Wing)
B B'
B=B'
A=A'
AA'
Appl y i ns tant typ e C A g lu e t o b oth side s o f eac h h inge.
Completed
Bottom View
PA2x8mm Screw
2
1mm
B
Apply instant type CA glue to both sides
of each hinge.
1.5mm
B'
B=B'
Completed
Plastic Collar
PA2x8mm
E205PO11571111

Elevator Pushrod
5
PM2x8mm Screw
4
Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please
look for pin-hole marks at under side of control surfaces.
P.5
Ø1.4x430mm
Pushrod
Rudder Pushrod
6
PM2x8mm Screw
2
Ø1mm pilot holes for World Models tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Rudder Pushrod
Ø1.4x400mm
2 m m
PM2x8mm
Clevis
Fuel Tube
Ø4x4mm
Clevis
Bottom View
PM2x8mm
Clevis
Fuel Tube
Ø4x4mm
2mm
Horn
215mm
30mm
55mm
160mm
TWM PL8210010
CLEVIS WRENCH
TWM PL8210010
CLEVIS WRENCH
E205PO11571111

P.6
7Outrunner Motor & Cowling
5
4
Don't over-tighten the PM2 screws, let the
propeller blades align themselves when spinning.
PM2 x 12mm
PM2 x 12mm
PA2.6 x 8mm
Spinner
Ø36mm
PWA2 x 8mm
1.5mm
6
PWA2x8mm Screw
4
4
PM2x12mm Screw
2
d3xD7mm Washer
4
M3x6mm Socket Head Screw
Outrunner Motor 28/ 30
KM0283010
Propeller Adaptor
(d3xD5) HW2340100
Optional Parts
TWM
KP0011310
SolderSolder
TWM HW3111400
PROPELLER ADAPTOR WRENCH
Don't over-tighten the
M3 screws, too much
stress on the screws
could split the firewall.
M3x6mm
d3xD7mm
Washer
1
3
2
M5 Nut
E205PO11571111

Radio Equipment
8
Receiver wrapped up in sponge.
Main Wing
9
PM2.5x20mm
d2.5xD8mm
Washer
Bottom View
Front
P.7
Main Landing gear
10
PA2.3x12mm Screw
4
2.6mm Collar
2
PA2.3x12mm
Landing
wire straps
62mm
54mm
1.5mm
Bottom View
M3x3mm Set Screw
2.6mm Collar
Double-Sided Tape
Brushless ESC
Sponge
Rudder Servo
Elevator Servo
Fuel Tube
Ø4x4mm
Rudder Pushrd
Ø1.4x400mm
Front
Battery
Battery Tie
Straper
KA1.7x5mm
Elevator Pushrod
Ø1.4x80mm
Elevator Servo
2
PM2.5x20mm Screw
d2.5xD8mm Washer
2
Switch
E205PO11571111

P.8
Canopy
11
PWA2x8mm Screw
4Front
1mm
Wing Setting
12
Adjust the wing and fuselage configuration as shown in the diagrams.
AA'
A=A' B=B' C=C'
B B'
C'
C
PWA2x8mm
E205PO11571111

P.9
Adjust the control throws as shown in the
diagram. These throws are good for general
flying. You can adjust according to your
personal preference.
Elevator
Control Throws
C.G.
14
Rudder
20mm
20mm
10mm
10mm
13
65mm
C.G.
The ideal C.G. position is behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
65mm (2.56in.)
Aileron
8mm
8mm
2.56 in
http://www.theworldmodels.com/para/instruction/instructionManuals.php
E205PO11571111
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
# is specially designed to be powered by KM0283010 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running
propeller. Extreme caution should be exercised when working with electric powered models. Make sure the
propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure
you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental
movement of the throttle stick will spin the propeller and could cause injuries.
# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles.
Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone.
Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the
glue and shrink the covering at the same time, causing the seams to pull away.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

Product Registration Form (US Customers)
We would like to share with you any relevant information regarding your model, including
product news and free upgrade parts when applicable. Please fill in the following and send to
AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA.
1. Name:
2. Address:
3. Phone #: E-mail:
4. Model:
Wing QC# Fuselage QC#
(QC numbers are stamped on wing and fuselage)
5. Date of Purchase:
6. Store Name:
Please call AirBorne Models at 925 371 0922 for any assistance in filling this form.
Thank you very much for purchasing our product.
E205PO11571111

The World Models
Manufacturing Co Ltd., .
www .theworl dmodels.com
E205PO11571111