Thermalright Macho 120 Rev.A User manual

Thermalright
Macho 120 Rev.A

Macho 120 Rev.A
Assembly package
× 1
4
4
8
× 1 × 2
× 1
× 4
× 4
× 4
× 7
× 5
Chill Factor 2g
× 4
× 4

Macho 120 Rev.A
1
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Intel 775/1150/1155/1156/1366
Macho Heatsink Body 120mm Fan Clip
120mm Fan
Screw Nut
Anti-Vibration Pads
Mounting Plate
M3 L6 Screw
Anchoring Mount
Intel Washer
(small)
M3 L10 Screw

The Ultimate Cooling Solutions!
www.thermalright.com
2
Component
1
1
2
2
3
3
4
4
5
5
6
76
7 8
9
9
10
13
11
14
12
12
1413
8
1110
Macho Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
120mm Fan Clip ×2
120mm Fan ×1
Thermal paste ×1
AMD Washer (big) ×4
Mounting Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4
Chill Factor 2g
M3 L6 Screw ×7
Screw driver ×1

3
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Take out Macho cooler from the paper box.
Remove the 120mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease
of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.Apply Anti-Vibration
Padding to 4 corners on the Heatsink Body.
1
1
2
2
3
3
4
4
Step 2 : Install the four screw pillars.
Take one M3L10 screw and put one washer for Intel around the screw pillar. Snap it through one of
holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and
then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern.
Step 3 : Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 screws to x the Anchoring Mount on to the Screw Nuts.

The Ultimate Cooling Solutions!
www.thermalright.com
4
Step 4:
Step 5:
Chill Factor
2g
Chill Factor
2g
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly.
Chill Factor
2g
Chill Factor
2g
Step 5: Mounting Plate Installation
Place the Heatsink Body on top of the CPU.
Make the Mounting Plate go through the Heatsink
Body. Then use the supplied Screw Driver
to fasten the two M3L6 Screws to Secure the
Mounting Plate.
Step 6: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the M3L6
Screw underneath the cooler.
Step 7: Step 8:
Step 7 : Fan Installation
Place the included 120mm fan onto the Heatsink
Body. And then secure it with the 120mm Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the 120mm Fan.
Step 8 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6:

Macho 120 Rev.A
5
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Macho Heatsink Body 120mm Fan Clip
120mm Fan
Mounting Plate
M3 L6 Screw
Anchoring Mount
LGA2011 Type B
Screw Pillars
Intel 2011
Anti-Vibration Pads

The Ultimate Cooling Solutions!
www.thermalright.com
6
Component
1
1
2
2
3
3
4
4
5
5
6
76
7 8
9
9
10
13
11
14
12
12
1413
8
1110
Macho Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
120mm Fan Clip ×2
120mm Fan ×1
Thermal paste ×1
AMD Washer (big) ×4
Mounting Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4
Chill Factor 2g
M3 L6 Screw ×7
Screw driver ×1

7
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Take out Macho cooler from the paper box.
Remove the 120mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease
of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.Apply Anti-Vibration
Padding to 4 corners on the Heatsink Body.
Step 2 : Install the four screw pillars.
Take one M3L10 screw and put one washer for Intel around the screw pillar. Snap it through one of
holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and
then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern.
Step 3 : Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 screws to x the Anchoring Mount on to the Screw Nuts.
12
3
4
12
3
4

Macho 120 Rev.A
The Ultimate Cooling Solutions!
www.thermalright.com
8
Step 4:
Step 5:
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly.
Step 5: Mounting Plate Installation
Place the Heatsink Body on top of the CPU. Make
the Mounting Plate go through the Heatsink Body.
Then use the supplied Screw Driver to fasten the
two M3L6 Screws to Secure the Mounting Plate.
Chill Factor
2g
Chill Factor
2g
Step 6:
Step 7: Step 8:
Step 7 : Fan Installation
Place the included 120mm Fan onto the Heatsink
Body. And then secure it with the 120mm Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the 120mm Fan.
Step 8 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body,
for easier access to the
M3L6 Screw underneath
the cooler.
Chill Factor
2g
Chill Factor
2g

Macho 120 Rev.A
9
Exploded View
Important! Before proceeding with installation, please check for the most
up-to-date instructions at www.thermalright.com
Macho Heatsink Body 120mm Fan Clip
120mm Fan
Screw Nut
Anti-Vibration Pads
Mounting Plate
M3 L6 Screw
Anchoring Mount
AMD Washer
(big) M3 L10 Screw
AM2/AM2+/AM3/AM3+/FM1/FM2

The Ultimate Cooling Solutions!
www.thermalright.com
10
Component
1
1
2
2
3
3
4
4
5
5
6
76
7 8
9
9
10
13
11
14
12
12
1413
8
1110
Macho Heatsink Body ×1
LGA2011 Type B
Screw Pillars x4
120mm Fan Clip ×2
120mm Fan ×1
Thermal paste ×1
AMD Washer (big) ×4
Mounting Plate ×1
M3 L10 Screw ×5
Anti-Vibration Pad ×4
Anchoring Mount ×1
Screw Nut ×4
Intel Washer (small) ×4
Chill Factor 2g
M3 L6 Screw ×7
Screw driver ×1

11
Installation Instructions:
Step 1:
Step 2:
Step 3:
Step 1 : Take out Macho cooler from the paper box.
Remove the 120mm Fan from the cooler by pulling the Fan Clips upwards in order to give room for ease
of installation. And leave the Fan Clips on the Heatsink Body. Do not remove them.Apply Anti-Vibration
Padding to 4 corners on the Heatsink Body.
Step 2 : Install the four screw pillars.
Take one M3L10 screw and put one washer for AMD around the screw pillar. Snap it through one of
holes around CPU socket from bottom towards top. Cap the screw pillar with the screw nut included and
then tighten up. Now repeat this installation for the other three screw pillars in a criss-cross pattern.
Step 3 : Place the Anchoring Mount on the Screw Nuts.
Use the four M3L6 screws to x the Anchoring Mount on to the Screw Nuts.
1
1
2
2
3
3
4
4

The Ultimate Cooling Solutions!
www.thermalright.com
12
Step 4:
Step 5:
Step 4 : Applying Thermal Paste
Apply the Thermal Paste to the base of the Heatsink and the surface of the CPU evenly.
Chill Factor
2g
Chill Factor
2g
Step 5: Mounting Plate Installation
Place the Heatsink Body on top of the CPU.
Make the Mounting Plate go through the Heatsink
Body. Then use the supplied Screw Driver
to fasten the two M3L6 Screws to Secure the
Mounting Plate.
Step 6: Easy Access
Pass the supplied Screw
Driver through the central
hole of the Heatsink Body, for
easier access to the M3L6
Screw underneath the cooler.
Step 7: Step 8:
Step 7 : Fan Installation
Place the included 120mm fan onto the Heatsink
Body. And then secure it with the 120mm Fan
Clips, by pulling the Fan Clips to place the four
ends at the four holes on the 120mm Fan.
Step 8 : Installation completed
Plug in the fan connector to the CPU PWM Fan
socket on the motherboard. Installation complete.
Step 6:
Chill Factor
2g
Chill Factor
2g

Macho 120 Rev.A
13
Technical Spec
Heatsink Specifications:
Dimension: Length 120mm x Width 102mm x Height 150.15mm
Weight: 634g (Heatsink only)
Heatpipe: 6mm heatpipe*5 units
Copper Base: C1100 Pure copper nickel plated
Fan Specification:
Dimension: L120mm x H120mm x W25mm
Weight: 150g
Fan speed: 600~1300RPM (PWM controlled)
Fan noise: 25.4dBA MAX (Test distance 1.0M)
Airflow: 46.19CFM MAX
Connector: 4 Pin (PWM Fan connector)

Macho 120 Rev.A
The Ultimate Cooling Solutions!
www.thermalright.com
14
120
102
40 40 40 51.85
36.6
105.15

Macho 120 Rev.A
15
Awards

The Ultimate Cooling Solutions!
www.thermalright.com
TEL: [phone]
FAX: [phone]
EMAIL: [email protected]