Xilinx ZCU102 Operation instructions

ZCU102 System
Controller – GUI
Tutorial
May 2019
XTP433

© Copyright 2019 Xilinx, Inc. Xilinx, the Xilinx logo, Artix, ISE, Kintex, Spartan, Virtex, Vivado, Zynq, and other designated brands included herein are
trademarks of Xilinx in the United States and other countries. All other trademarks are the property of their respective owners.
NOTICE OF DISCLAIMER: The information disclosed to you hereunder (the “Information”) is provided “AS-IS” with no warranty of any kind, express or implied.
Xilinx does not assume any liability arising from your use of the Information. You are responsible for obtaining any rights you may require for your use of this
Information. Xilinx reserves the right to make changes, at any time, to the Information without notice and at its sole discretion. Xilinx assumes no obligation to
correct any errors contained in the Information or to advise you of any corrections or updates. Xilinx expressly disclaims any liability in connection with technical
support or assistance that may be provided to you in connection with the Information. XILINX MAKES NO OTHER WARRANTIES, WHETHER EXPRESS,
IMPLIED, OR STATUTORY, REGARDING THE INFORMATION, INCLUDING ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR NONINFRINGEMENT OF THIRD-PARTY RIGHTS.
Revision History
Date Version Description
07/26/19 11.1 Minor update of details on VADJ and MIG.
05/29/19 11.0 Updated for 2019.1.
02/25/19 10.1 Updated document format.
12/10/18 10.0 Updated for 2018.3.
06/18/18 9.0 Updated for 2018.2
04/09/18 8.0 Updated for 2018.1.
12/20/17 7.0 Updated for 2017.4
10/09/17 6.0 Updated for 2017.3.
06/20/17 5.0 Updated for 2017.2.
04/19/17 4.0 Updated for 2017.1.
12/19/16 3.0 Updated for 2016.4.
10/13/16 2.0 Updated for SCUI version 1.1.

Overview
˃Xilinx ZCU102 Board
˃Updating the Firmware
˃ZCU102 SCUI
Clocks
Voltages
Power
FMC
GTR MUX
EEPROM Data
GPIO Commands
System Monitor
About
˃References
Note: This presentation applies to the ZCU102

Xilinx ZCU102 Board
Note: Presentation applies to the ZCU102

ZCU102 Software Install and Board Setup
˃Refer to XTP435 – ZCU102 Software Install and Board Setup for details on:
Software Requirements
ZCU102 Board Setup
Note: Presentation applies to the ZCU102

ZCU102 System Controller Files
˃Open the RDF0382 – ZCU102 System Controller GUI (2019.1 C) ZIP file
Extract these files to your C:\ drive
Note: Presentation applies to the ZCU102

Updating the Firmware

Updating the Firmware
˃This System Controller GUI requires the latest version of firmware
˃Xilinx recommends all ZCU102 users update their MSP430 firmware to the
latest version
˃You can determine the firmware version by opening a Terminal, connected
to Interface 3:
Note: Presentation applies to the ZCU102

Updating the Firmware
˃In this terminal, after power on, type:
@ver
˃The timestamp of the firmware will appear
˃Any firmware with a timestamp before Jul 5 2017 should be updated
Note: Presentation applies to the ZCU102

Updating the Firmware
˃To update the firmware, attach two jumpers across J164 as shown
Note: Presentation applies to the ZCU102

Updating the Firmware
˃Note: Some older ZCU102 boards, such as
Rev D.2, do not have J164. For these
boards, connect two long jumpers:
From J87 (PMOD1), Pin 1 to J92, Pin 11
From J87 (PMOD1), Pin 3 to J92, Pin 8
J92 connections J87 connections
J92
J87
Pin 8
Pin 11
Note: Presentation applies to the ZCU102

Updating the Firmware
˃Run the BIT.exe from C:\zcu102_scui\flash_restore
Note: Close the Terminal Window before restoring flash

Running the System
Controller GUI

Running the System Controller GUI
˃From C:\zcu102_scui, double click on BoardUI.exe
˃Enter the board serial number and MAC ID
˃Click OK
Note: Presentation applies to the ZCU102

Clocks

Setting the clocks
˃Select the Set tab underneath the Clocks tab
˃Enter 156.25 for the Si5328 and click the Set Si5328 Frequency button
(takes a long moment to complete)
Note: Presentation applies to the ZCU102

Reading the clocks
˃Select the Read tab
˃Click each of the Read buttons and verify the frequencies are set as shown
Note: Presentation applies to the ZCU102

Reading the clocks
˃If some of the frequencies show up different, you will need to restore the
defaults
Note: Presentation applies to the ZCU102

Restore Default Clock settings
˃Select the Restore Device Defaults tab
˃Restore the defaults by clicking the button associated with the clock you
want to restore (300 MHz, 156.25 MHz, and 0 MHz)
Note: Presentation applies to the ZCU102

Restore Default Clock settings
˃Return to the Read tab and verify the settings are correct
Note: Presentation applies to the ZCU102