THIESSENS TH3BCMP User manual

WARNING: PLEASE READ THE ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS
GAS APPLIANCE. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY
DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.
FOR OUTDOOR AND HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
FUEL AND ACCESSORIES NOT INCLUDED.
TH3BCMP
THIESSENS.COM
58211
300522
3 BURNER CAMP STOVE
WITH FOLDING SIDE TABLE
IMPORTANT, READ CAREFULLY, RETAIN FOR FUTURE
REFERENCE. MANUAL MUST BE READ BEFORE OPERATING!
MANUAL

2
THIESSENS : Authentic Pursuit Equipment
MAJOR CAUSES OF APPLIANCE FIRES ARE A RESULT OF POOR
MAINTENANCE AND A FAILURE TO MAINTAIN REQUIRED
CLEARANCE TO COMBUSTIBLE MATERIALS. IT IS OF UTMOST
IMPORTANCE THAT THIS PRODUCT BE USED ONLY IN
ACCORDANCE WITH THE FOLLOWING INSTRUCTIONS.
PLEASE READ AND UNDERSTAND THIS ENTIRE MANUAL BEFORE ATTEMPTING TO ASSEMBLE, OPERATE OR INSTALL THE PRODUCT. THIS
WILL ENSURE YOU RECEIVE THE MOST ENJOYABLE AND TROUBLE-FREE OPERATION OF YOUR NEW GAS CAMP STOVE. WE ALSO ADVISE
YOU RETAIN THIS MANUAL FOR FUTURE REFERENCE.
PROPANE GAS WARNINGS
DANGER DANGER
IF YOU SMELL GAS:
• SHUT OFF GAS TO THE APPLIANCE.
• EXTINGUISH ANY OPEN FLAME.
• OPEN LID.
• IF ODOR CONTINUES, KEEP AWAY FROM THE APPLIANCE
AND IMMEDIATELY CALL YOUR GAS SUPPLIER OR YOUR
FIRE DEPARTMENT.
NEVER OPERATE THIS APPLIANCE:
• UNATTENDED.
• WITHIN 3.0 M (10 FT) OF ANY STRUCTURE,
COMBUSTIBLE MATERIAL OR OTHER GAS
CYLINDER.
• WITHIN 7.5 M (25 FT) OF ANY FLAMMABLE
LIQUID.
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN FIRE OR EXPLOSION WHICH COULD CAUSE PROPERTY
DAMAGE, PERSONAL INJURY OR DEATH.
1. ENSURE THE GAS CYLINDER IS PURCHASED BY A REPUTABLE SUPPLIER. AN INCORRECTLY FILLED OR AN OVERFILLED GAS CYLINDER
CAN BE DANGEROUS. THE OVERFILLED CONDITION COMBINED WITH THE WARMING OF THE GAS CYLINDER (A HOT SUMMER DAY,
GAS CYLINDER LEFT IN THE SUN, ETC.) CAN CAUSE LP GAS TO BE RELEASED SINCE THE TEMPERATURE INCREASE CAUSES GAS TO
EXPAND. GAS RELEASED FROM THE CYLINDER IS FLAMMABLE AND CAN BE EXPLOSIVE.
2. DO NOT USE AN LP GAS CYLINDER IF IT HAS A DAMAGED VALVE OR SHOWS SIGNS OF DENTS, GOUGES, BULGES, FIRE DAMAGE,
CORROSION, LEAKAGE, EXCESSIVE RUST, OR OTHER FORMS OF VISUAL EXTERNAL DAMAGE; IT MAY BE HAZARDOUS AND SHOULD
BE CHECKED IMMEDIATELY BY A LIQUID PROPANE SUPPLIER.
IF YOU SEE, SMELL, OR HEAR THE HISS OF GAS ESCAPING FROM THE CYLINDER, DO NOT ATTEMPT TO LIGHT APPLIANCE.
EXTINGUISH ANY OPEN FLAME. DISCONNECT FROM FUEL SUPPLY.
3. DO NOT CONNECT OR DISCONNECT THE GAS CYLINDER WHILE THE UNIT IS IN USE OR IS STILL HOT. WHEN CAMP STOVE IS NOT IN
USE, ENSURE SUPPLY CYLINDER IS TURNED TO OFF AND DISCONNECT THE GAS CYLINDER. NEVER MOVE OR TRANSPORT THE UNIT
WHILE THE GAS CYLINDER IS ATTACHED. DO NOT STORE A SPARE LP GAS CYLINDER UNDER OR NEAR THE APPLIANCE.
4. PARTS SEALED BY MANUFACTURER SHALL NOT BE MANIPULATED BY THE USER. DO NOT MOVE THE APPLIANCE DURING USE. TURN
OFF THE GAS SUPPLY AT THE GAS CYLINDER AFTER USE. DO NOT MODIFY THE APPLIANCE. THE REPLACEMENT HOSE ASSEMBLY
SHALL BE THAT SPECIFIED BY THE MANUFACTURER.
5. OPERATE THIS APPLIANCE USING LIQUEFIED PETROLEUM ONLY, WHICH IS ALSO SPECIFIED ON THE RATING LABEL ON THE UNIT. DO
NOT ATTEMPT TO OPERATE YOUR CAMP STOVE ON OTHER GASES. DO NOT ATTEMPT TO CONVERT THIS LP UNIT TO NATURAL GAS.
FAILURE TO FOLLOW THIS WARNING COULD LEAD TO FIRE, BODILY HARM, AND WILL VOID YOUR WARRANTY.
6. ALWAYS CHECK FOR GAS LEAKS WHEN YOU CONNECT AND DISCONNECT THE REGULATOR TO THE GAS CYLINDER, ESPECIALLY AFTER
A PERIOD OF STORAGE (FOR EXAMPLE, OVER WINTER). CHECK ALL CONNECTIONS FOR LEAKS WITH A SOAPY WATER SOLUTION AND
BRUSH. NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS.

3
www.thiessens.com
DANGERS AND WARNINGS
1. A MINIMUM CLEARANCE OF 3 M (10 FEET) FROM COMBUSTIBLE CONSTRUCTIONS TO ALL SIDES OF THE UNIT MUST BE MAINTAINED.
DO NOT USE THIS APPLIANCE INDOORS OR IN AN ENCLOSED, UNVENTILATED AREA. THIS APPLIANCE MUST NOT BE PLACED UNDER
OVERHEAD COMBUSTIBLE CEILING OR OVERHANG, INCLUDING ON OR UNDER ANY APARTMENT, OR CONDOMINIUM BALCONY OR
DECK. USE THE BURNER ON A STABLE LEVELED NON-COMBUSTIBLE SURFACE AND IN AN AREA CLEAR OF COMBUSTIBLE MATERIALS.
AN ASPHALT SURFACE (BLACKTOP) MAY NOT BE ACCEPTABLE FOR THIS PURPOSE.
SHOULD A GREASE FIRE OCCUR, TURN THE CAMP STOVE OFF UNTIL THE FIRE IS OUT. DO NOT THROW WATER ON. DO NOT
TRY TO SMOTHER THE FIRE. USE OF AN ALL-CLASS (CLASS ABC) APPROVED FIRE EXTINGUISHER IS VALUABLE TO KEEP ON
SITE. IF AN UNCONTROLLED FIRE DOES OCCUR, CALL THE FIRE DEPARTMENT.
2. THIS OUTDOOR CAMP STOVE IS NOT INTENDED FOR INSTALLATION IN/ON RECREATION VEHICLES OR BOATS.
NEVER USE THIS APPLIANCE IN AN ENCLOSED SPACE, SUCH AS A CAMPER, TENT, CAR, BOAT OR HOME. THIS APPLIANCE
IS NOT INTENDED FOR AND SHOULD NEVER BE USED AS A HEATER.
3. THIS APPLIANCE IS NOT RECOMMENDED FOR CHILDREN, PERSONS WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY ARE UNDER DIRECT SUPERVISION OR INSTRUCTION BY A PERSON
RESPONSIBLE FOR THEIR SAFETY. THE USE OF ALCOHOL, PRESCRIPTION, OR NON-PRESCRIPTION DRUGS MAY IMPAIR THE
CONSUMER'S ABILITY TO PROPERLY ASSEMBLE OR SAFELY OPERATE THE APPLIANCE.
4. DO NOT PLACE AN EMPTY COOKING VESSEL ON THE APPLIANCE WHILE IN OPERATION. USE CAUTION WHEN PLACING ANYTHING IN
COOKING VESSEL WHILE THE APPLIANCE IS IN OPERATION. NEVER USE A COOKING VESSEL LARGER THAN 220 MM / 8.66 INCHES.
5. PARTS OF THE CAMP STOVE MAY BE VERY HOT, AND SERIOUS INJURY MAY OCCUR. KEEP YOUNG CHILDREN AND PETS AWAY WHILE
IN USE. DO NOT TOUCH HOT SURFACES. USE HEAT-RESISTANT GLOVES, LONG-HANDLED TONGS, OR COOKING MITTS AT ALL TIMES,
SINCE THE CAMP STOVE WILL BECOME VERY HOT.
6. DO NOT OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR TO THIS APPLIANCE. KEEP THE BURNER TUBE AND PORTHOLES
CLEAN AND FREE FROM DEBRIS. CLEAN BEFORE USE. REGULAR CARE AND MAINTENANCE IS REQUIRED TO PROLONG THE LIFESPAN
OF YOUR UNIT. KEEP THE FUEL SUPPLY HOSE AWAY FROM ANY HEATED SURFACE(S).
7. CLEAN AND INSPECT THE GAS REGULATOR BEFORE EACH USE OF THE OUTDOOR COOKING GAS APPLIANCE. REPLACE THE GAS
REGULATOR PRIOR TO BEING USED IF THERE IS EVIDENCE OF EXCESSIVE ABRASION OR WEAR.
CARBON MONOXIDE
CARBON MONOXIDE IS A COLORLESS, ODORLESS, TASTELESS GAS PRODUCED BY BURNING GAS, WOOD, PROPANE, CHARCOAL OR ANY
OTHER FUELS. CARBON MONOXIDE REDUCES THE BLOOD’S ABILITY TO CARRY OXYGEN. LOW BLOOD OXYGEN LEVELS CAN RESULT IN
HEADACHES, DIZZINESS, WEAKNESS, NAUSEA, VOMITING, SLEEPINESS, CONFUSION, LOSS OF CONSCIOUSNESS OR DEATH. FOLLOW
THESE GUIDELINES TO PREVENT THIS COLORLESS, ODORLESS GAS FROM POISONING YOU, YOUR FAMILY, OR OTHERS:
• SEE A DOCTOR IF YOU OR OTHERS DEVELOP COLD OR FLU-LIKE SYMPTOMS WHILE COOKING OR IN THE VICINITY OF THE APPLIANCE.
CARBON MONOXIDE POISONING, WHICH CAN EASILY BE MISTAKEN FOR A COLD OR FLU, IS OFTEN DETECTED TOO LATE.
• ALCOHOL CONSUMPTION AND DRUG USE INCREASE THE EFFECTS OF CARBON MONOXIDE POISONING.
CARBON MONOXIDE IS ESPECIALLY TOXIC TO MOTHER AND CHILD DURING PREGNANCY, INFANTS, THE ELDERLY, SMOKERS, AND PEOPLE
WITH BLOOD OR CIRCULATORY SYSTEM PROBLEMS, SUCH AS ANEMIA, OR HEART DISEASE.
SAFETY LISTING
CONFORMS TO ANS Z21.89-2017, CSA 1.18-2017, OUTDOOR COOKING GAS APPLIANCE. INSTALLATION MUST
CONFORM WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE NATIONAL FUEL GAS CODE,
ANS Z223.1/NFPA 54, STORAGE AND HANDLING OF LIQUEFIED PETROLEUM GASES, ANS/NFPA 58; OR NATURAL
GAS AND PROPANE INSTALLATION CODE, CSA 8149. 1; PROPANE STORAGE AND HANDLING, CSA 8149.2; OR
THE STANDARD FOR RECREATIONAL VEHICLES, ANS A119.2/NFPA 1192, AND RECREATIONAL VEHICLE CODE,
CSA Z240 RV SERIES, AS APPLICABLE.

4
THIESSENS : Authentic Pursuit Equipment
COPYRIGHT NOTICE
COPYRIGHT 2021. ALL RIGHT RESERVED.
NO PART OF THIS MANUAL MAY BE
COPIED, TRANSMITTED, TRANSCRIBED,
STORED IN A RETRIEVAL SYSTEM, IN
ANY FORM OR BY ANY MEANS WITHOUT
EXPRESSED WRITTEN PERMISSION OF,
MANUFACTURED BY:
DANSONS, 3411 NORTH 5TH AVENUE,
SUITE 500, PHOENIX, AZ, USA 85013
CUSTOMER CARE
TOLL-FREE: 1-877-972-5742
TABLE OF CONTENTS
PROPANE GAS WARNINGS ....................................... 2
DANGERS & WARNINGS........................................... 3
CARBON MONOXIDE ................................................ 3
PARTS AND SPECS................................................... 5
ASSEMBLY PREPARATION ........................................ 6
ASSEMBLY INSTRUCTIONS....................................... 6
GAS CYLINDER REQUIREMENTS............................... 8
CONNECTING THE GAS CYLINDER............................. 8
PREPARATION FOR USE - LEAK TESTING ................... 9
DISCONNECTING THE GAS CYLINDER ....................... 9
AUTOMATIC LIGHTING PROCEDURE........................ 10
MANUAL LIGHTING PROCEDURE ............................ 10
SHUTTING OFF YOUR UNIT...................................... 11
COLLAPSING FOR TRANSPORT ............................... 11
CARE AND MAINTENANCE...................................... 12
TROUBLESHOOTING............................................... 13
REPLACEMENT PARTS............................................ 14
WARRANTY ............................................................ 15

5
www.thiessens.com
PART DESCRIPTION
1 Support Frame (x1)
2 Bracket A (x1)
3 Bracket B (x1)
4 Side Table (x1)
5 Side Table Bracket (x1)
6 Stove Body (x1)
A Screw (x12)
B Step Screw (x2)
NOTE: Due to ongoing product development, parts are subject to change without notice. Contact Customer
care if parts are missing when assembling the unit.
MODEL TH3BCMP
ASSEMBLED
(L x W x H)
78.3 x 24.8 x 36.9 in.
(199 x 63.2 x 93.8 cm)
WEIGHT 68.3 lb
(31.0 kg)
COOKING AREA 486.2 in2
(3,136 cm2)
BTU 90,000
PARTS AND SPECS
6
3
4
5
2
A
B
1

6
THIESSENS : Authentic Pursuit Equipment
ASSEMBLY PREPARATION
PARTS ARE LOCATED THROUGHOUT THE SHIPPING CARTON. INSPECT THE UNIT, PARTS, AND HARDWARE AFTER REMOVING FROM THE
PROTECTIVE SHIPPING CARTON. DISCARD ALL PACKAGING MATERIALS FROM INSIDE AND OUTSIDE OF THE UNIT BEFORE ASSEMBLY,
THEN REVIEW AND INSPECT ALL PARTS BY REFERENCING THE PARTS LIST. IF ANY PART IS MISSING OR DAMAGED, DO NOT ATTEMPT
TO ASSEMBLE. SHIPPING DAMAGE IS NOT COVERED UNDER WARRANTY. CONTACT CUSTOMER CARE FOR PARTS: MONDAY THROUGH
SUNDAY, 4 A.M. – 8 P.M. PST (EN/FR/ES).
• TOOLS REQUIRED FOR ASSEMBLY: PHILLIPS SCREWDRIVER. TOOLS NOT INCLUDED.
TO EASE INSTALLATION, USING TWO PEOPLE IS HELPFUL (BUT NOT NECESSARY) WHEN ASSEMBLING THIS UNIT.
ASSEMBLY INSTRUCTIONS
PLACE A PIECE OF CARDBOARD ON THE FLOOR TO PREVENT SCRATCHING THE UNIT AND PARTS DURING ASSEMBLY.
Turn over the Stove Body so it lies flat-side down on the cardboard. Push
down the Locking Pin to release each Support Leg. Extend each of the
four Support Legs until the Locking Pins lock at full extension.
On the front Support Legs only, tighten the Support Leg fixing screws to
lock all Support Legs in place.
1 2
Turn over the Stove Body so it stands on the Support Legs. Install Bracket
D to the left side of the Stove Body using four screws, as shown.
Mount Bracket A and Bracket B to the left side of the Side Table (handle
faces the front) using two screws in each Bracket, as shown.
3 4
1
8
4
56
7
3
2
A
B
1
8
4
56
7
3
2
A
B

7
www.thiessens.com
If ground is uneven, rotate the bottom half of each Support Leg to adjust
the height. Adjustment variant is up to 1.5 inches / 38 mm. Assembly of
unit is now complete.
8
Lift the Wind Shield upright and expand the Wind Shield Side Wings.
Place the tabs of the Wind Shield Side Wings into the small tab openings
near the front two corners of the Stove Body top.
7
Fasten the Support Frame to the Side Table using two step screws. To
secure the Support Frame in expanded position, swing the Locking Plate
onto the Locking Pin.
5
1
8
4
56
7
3
2
A
B
Fasten the Side Table to the Stove Body using four screws.
6
1
8
4
56
7
3
2
A
B

8
THIESSENS : Authentic Pursuit Equipment
GAS CYLINDER REQUIREMENTS
THE CAMP STOVE IS SET AND TESTED WITH LIQUID PROPANE (LP) GAS ONLY. THE REGULATOR SUPPLIED IS SET FOR 27.94 CM (11 INCH)
WATER COLUMN (WC) AND IS FOR USE WITH LP GAS ONLY. THE FACTORY-SUPPLIED REGULATOR AND HOSE MUST BE USED WITH A 9 KG
(20 LB) LP GAS TANK. CONTACT YOUR GAS SUPPLIER FOR A SPECIAL REGULATOR FOR BULK GAS THAT FUELS OTHER APPLIANCES.
CAUTION: IT IS IMPORTANT TO INSPECT THE FULL LENGTH OF THE GAS LINE HOSE. IF IT IS EVIDENT THERE IS EXCESSIVE
ABRASION OR WEAR, OR THE HOSE IS CUT, THE HOSE MUST BE REPLACED PRIOR TO THE APPLIANCE BEING USED.
THE LP-GAS SUPPLY CYLINDER TO BE USED MUST BE CONSTRUCTED AND MARKED IN ACCORDANCE WITH THE SPECIFICATIONS FOR
LP-GAS CYLINDERS, U.S. DEPARTMENT OF TRANSPORTATION (DOT) OR THE STANDARD FOR CYLINDERS, SPHERES AND TUBES FOR THE
TRANSPORTATION OF DANGEROUS GOODS, CAN/CSA-B339. CYLINDER SYSTEM MUST BE ARRANGED FOR VAPOR WITHDRAWAL.
1. DO NOT STORE A SPARE LP GAS CYLINDER UNDER OR NEAR THIS APPLIANCE.
2. NEVER FILL THE GAS CYLINDER BEYOND 80 PERCENT FULL.
3. IF THE INFORMATION IN 1) AND 2) IS NOT FOLLOWED EXACTLY A FIRE CAUSING DEATH OR SERIOUS INJURY MAY OCCUR.
4. PLACE DUST CAP ON CYLINDER VALVE OUTLET WHENEVER THE CYLINDER IS NOT IN USE. ONLY INSTALL THE TYPE OF DUST CAP ON
THE CYLINDER VALVE OUTLET THAT IS PROVIDED WITH THE CYLINDER VALVE. OTHER TYPES OF CAPS OR PLUGS MAY RESULT IN
LEAKAGE OF PROPANE.
5. THE LP GAS CYLINDER USED MUST HAVE A COLLAR TO PROTECT THE GAS CYLINDER VALVE.
6. ALWAYS KEEP THE LP CYLINDER AT 90 DEGREES (UPRIGHT) ORIENTATION TO PROVIDE VAPOR WITHDRAWAL.
NOTE: THE NORMAL FLOW OF GAS THROUGH THE REGULATOR AND HOSE ASSEMBLY CAN CREATE A HUMMING NOISE.
A LOW VOLUME OF NOISE IS PERFECTLY NORMAL AND WILL NOT INTERFERE WITH OPERATION OF THE CAMP STOVE. IF
HUMMING NOISE IS LOUD AND EXCESSIVE YOU MAY NEED TO PURGE AIR FROM THE GAS LINE OR RESET THE REGULATOR
EXCESS GAS FLOW DEVICE. THIS PURGING PROCEDURE SHOULD BE DONE EVERY TIME A NEW LP GAS TANK IS CONNECTED
TO YOUR CAMP STOVE.
CONNECTING THE GAS CYLINDER
IMPORTANT: IF THE MANIFOLD REQUIRES A CONNECTOR, FOLLOW THE CONNECTOR INSTALLATION INSTRUCTIONS PRIOR
TO CONNECTING THE UNIT TO A GAS CYLINDER.
1. BEFORE CONNECTING, ENSURE THERE IS NO DEBRIS CAUGHT IN THE HEAD OF THE LP GAS CYLINDER, HEAD OF THE REGULATOR
VALVE, OR IN THE HEAD OF THE BURNER AND BURNER PORTS.
2. CONNECT THE TUBE LINE TO THE MANIFOLD BY TURNING THE KNOB CLOCKWISE UNTIL IT STOPS. MAKE SURE THAT THE TUBE IS NOT
TWISTED IN ANY WAY.
3. PLACE A GAS CYLINDER NEXT TO THE CAMP STOVE ON THE
RIGHT SIDE. MAKE SURE THE GAS CYLINDER VALVE IS IN
THE CLOSED POSITION. IT IS IMPORTANT TO ENSURE THE
GAS CYLINDER IS COMPLETELY UPRIGHT, AS IT IS UNSAFE
TO OPERATE THE CAMP STOVE IF THE GAS CYLINDER IS NOT
PROPERLY LEVEL OR ON A STABLE SURFACE.
4. ENSURE THE CONTROL KNOBS ON THE CAMP STOVE ARE
COMPLETELY CLOSED BY TURNING THE KNOB CLOCKWISE TO
THE "OFF" POSITION.
5. REMOVE THE PROTECTIVE CAPS FROM THE REGULATOR VALVE
OPENING AND THE TOP OF THE GAS CYLINDER. SAVE THE
CAPS.
6. INSERT THE GAS CYLINDER VALVE INTO THE THREADED
OPENING OF THE REGULATOR VALVE. TURN THE QUICK
COUPLING NUT CLOCKWISE UNTIL FIRM. HAND-TIGHTEN ONLY.
7. GAS CYLINDER IS NOW INSTALLED. PERFORM A LEAK TEST.
25 CM
10 IN.

9
www.thiessens.com
WARNING: SHUT OFF THE GAS CYLINDER IF YOU SMELL GAS. ATTEMPT TO RE-INSTALL THE GAS CYLINDER TO ENSURE
THAT TUBE IS CONNECTED PROPERLY. PERFORM A LEAK TEST.
NOTE: THE NORMAL FLOW OF GAS THROUGH THE REGULATOR AND HOSE ASSEMBLY CAN CREATE A HUMMING NOISE.
A LOW VOLUME OF NOISE IS PERFECTLY NORMAL AND WILL NOT INTERFERE WITH OPERATION OF THE CAMP STOVE. IF
HUMMING NOISE IS LOUD AND EXCESSIVE YOU MAY NEED TO PURGE AIR FROM THE GAS LINE OR RESET THE REGULATOR
EXCESS GAS FLOW DEVICE. THIS PURGING PROCEDURE SHOULD BE DONE EVERY TIME A NEW GAS CYLINDER IS
CONNECTED TO YOUR CAMP STOVE.
PREPARATION FOR USE – LEAK TESTING
A LEAK TEST IS USED TO DETERMINE THE INTEGRITY OF A SEAL. BEFORE USING YOUR CAMP STOVE, PERFORM A LEAK TEST ON THE
CONNECTION BETWEEN THE REGULATOR AND THE GAS CYLINDER TO REDUCE THE RISK OF SERIOUS BODILY INJURY OR DEATH FROM FIRE
OR EXPLOSION. A LEAK TEST SHOULD BE PERFORMED A MINIMUM OF ONCE A SEASON, AS WELL AS:
• BEFORE LIGHTING YOUR CAMP STOVE FOR THE FIRST TIME,
• EVERY TIME THE GAS CYLINDER HAS BEEN CHANGED,
• AFTER TRAVEL, ESPECIALLY OVER ROUGH OR BUMPY ROADS,
• AFTER A PROLONGED PERIOD OF STORAGE OR NON-USE.
HOW TO PERFORM A LEAK TEST
BEFORE YOU USE THE BURNER FOR THE FIRST TIME, AND ALSO PERIODICALLY, CHECK THE WHOLE SYSTEM FOR LEAKS
FOLLOWING THE PROCEDURE LISTED BELOW. ALTERNATIVELY, IF THE SMELL OF GAS IS DETECTED AT ANYTIME DURING
USE OF THE UNIT, TURN OFF GAS SUPPLY AND IMMEDIATELY CHECK THE ENTIRE SYSTEM FOR LEAKS.
LEAK TEST PROCEDURE
1. PREPARE A SOAPY SOLUTION IN A 30/70% PROPORTION OF DISH LIQUID DETERGENT AND WATER.
2. MAKE SURE ALL CONTROL KNOBS ARE AT THE OFF POSITION.
3. OPEN GAS CYLINDER VALVE.
4. USING A SPRAY BOTTLE OR APPLICATOR BRUSH, APPLY THE SOLUTION TO THE FITTINGS, ALL CONNECTIONS AND
GAS HOSES. FOR THE INITIAL LEAK TEST, MAKE SURE THE LP CYLINDER IS FULL.
5. FORMATION OF BUBBLES INDICATE A LEAK. IF A LEAK IS IDENTIFIED, CLOSE GAS CYLINDER VALVE, RE-TIGHTEN
LOOSE FITTINGS AND TEST AGAIN. IF LEAK PERSISTS OR REQUIRES REPLACEMENT OF A PART, CONTACT YOUR
RESELLER OR A QUALIFIED GAS TECHNICIAN.
ONLY THOSE PARTS RECOMMENDED BY THE MANUFACTURER SHOULD BE USED ON THIS APPLIANCE. SUBSTITUTION WILL
VOID THE WARRANTY. DO NOT USE THIS APPLIANCE UNTIL ALL CONNECTIONS HAVE BEEN CHECKED AND DO NOT LEAK.
DISCONNECTING THE GAS CYLINDER
1. TURN ALL CONTROL KNOBS TO "OFF" POSITION ON THE CAMP STOVE. ENSURE THE REGULATOR VALVE ON THE GAS CYLINDER IS
COMPLETELY CLOSED BY TURNING THE KNOB TO THE CLOSED POSITION.
2. TURN THE QUICK COUPLING NUT COUNTER-CLOCKWISE (BY HAND) TO DISCONNECT FROM THE REGULATOR VALVE OPENING. REPLACE
THE PROTECTIVE CAPS ON THE REGULATOR VALVE OPENING AND THE TOP OF THE GAS CYLINDER FOR STORAGE (IF NOT EMPTY).
WARNING: IF STORING THE UNIT INDOORS, LEAVE THE GAS CYLINDER OUTDOORS. DO NOT FOLD UP OR TRANSPORT
UNIT WITH GAS CYLINDER ATTACHED. THE CYLINDER MAY LOOSEN OFF THE VALVE AND CAUSE A GAS LEAK, POSSIBLY
RESULTING IN AN EXPLOSION, FIRE, OR SEVERE BODILY HARM. DISCONNECT GAS CYLINDER FIRST BEFORE TRAVEL OR
STORAGE.

10
THIESSENS : Authentic Pursuit Equipment
AUTOMATIC LIGHTING PROCEDURE
WITH ALL OUTDOOR APPLIANCES, OUTSIDE WEATHER CONDITIONS PLAY A BIG PART IN THE PERFORMANCE OF YOUR UNIT AND THE
COOKING TIME NEEDED TO PREPARE YOUR MEALS. ALL THIESSENS UNITS SHOULD KEEP A MINIMUM CLEARANCE OF 3 M (10 FEET) FROM
COMBUSTIBLE CONSTRUCTIONS, AND THIS CLEARANCE MUST BE MAINTAINED WHILE THE UNIT IS OPERATIONAL. THIS APPLIANCE MUST
NOT BE PLACED UNDER OVERHEAD COMBUSTIBLE CEILING OR OVERHANG. KEEP YOUR UNIT IN AN AREA CLEAR FROM COMBUSTIBLE
MATERIALS, OR OTHER FLAMMABLE VAPORS AND LIQUIDS.
1. OPEN WIND SHIELD PANELS DURING LIGHTING.
2. SET ALL CONTROL KNOBS TO THE “OFF” POSITION.
3. OPEN THE CYLINDER/GAS VALVE ACCORDING TO THE
OPERATING INSTRUCTIONS ON TANK.
4. PUSH IN THE REGULATOR KNOB AND TURN COUNTER-
CLOCKWISE TO HIGH UNTIL YOU HEAR A "CLICK" SOUND
TO INDICATE A SPARK FROM THE IGNITER, AND LOOK FOR
FLAME TO ENSURE THE BURNER IS LIT.
5. AFTER THE BURNER HAS CAUGHT FIRE, YOU ARE READY TO
ENJOY YOUR CAMP STOVE AT YOUR DESIRED TEMPERATURE!
NOTE: DO NOT USE SPIRIT, LIGHTER-FLUID OR KEROSENE FOR LIGHTING.
6. IF THE BURNER DOES NOT LIGHT WITHIN 5 SECONDS, TURN BURNER CONTROL KNOB TO “OFF”, WAIT 5 MINUTES, AND REPEAT
LIGHTING INSTRUCTION. AFTER LIGHTING, OBSERVE THE BURNER FLAME. MAKE SURE ALL BURNER PORTS ARE LIT AND FLAME
HEIGHT MATCHES ILLUSTRATION SHOWN ABOVE.
WARNING: NEVER LEAN OVER THE COOKING AREA WHILE LIGHTING YOUR CAMP STOVE. KEEP YOUR FACE AND BODY A
SAFE DISTANCE (AT LEAST 18 INCHES / 457 MM) FROM THE COOKING SURFACE WHEN LIGHTING YOUR STOVE BY MATCH.
7. IF THE ABOVE POINTS DO NOT WORK, SEE MANUAL LIGHTING PROCEDURE.
MANUAL LIGHTING PROCEDURE
1. OPEN WIND SHIELD PANELS DURING LIGHTING.
2. SET ALL CONTROL KNOBS TO THE “OFF” POSITION.
3. OPEN THE CYLINDER/GAS VALVE ACCORDING TO THE OPERATING INSTRUCTIONS ON TANK.
4. QUICKLY AND CAREFULLY, USE A LONG MATCH OR LONG-NOSED LIGHTER TO LIGHT THE BURNER. POSITION LIT MATCH NEAR THE
SIDE OF THE BURNER.
CAUTION: DO NOT ATTEMPT TO LIGHT ANOTHER AREA OF THE BURNER. THIS CAN CAUSE INJURY.
5. PUSH AND TURN THE BURNER CONTROL KNOB COUNTER-CLOCKWISE TO HIGH, HOLD THIS KNOB IN FOR 10 SECONDS AFTER THE
BURNER IS LIT. YOU WILL HEAR THE “SNAPPING” SOUND OF THE SPARK UNTIL AFTER THE KNOB IS RELEASED.
6. REPEAT SAME STEPS FOR OTHER BURNERS, AS EACH BURNER LIGHTS INDEPENDENTLY.
NOTE: DO NOT USE SPIRIT, LIGHTER-FLUID OR KEROSENE FOR LIGHTING.
7. IF THE BURNER DOES NOT LIGHT WITHIN 5 SECONDS, TURN BURNER CONTROL KNOB TO “O”, WAIT 5 MINUTES, AND REPEAT
LIGHTING INSTRUCTION. AFTER LIGHTING, OBSERVE THE BURNER FLAME. MAKE SURE ALL BURNER PORTS ARE LIT AND FLAME
HEIGHT MATCHES ILLUSTRATION SHOWN PREVIOUSLY.
WARNING: NEVER LEAN OVER THE COOKING AREA WHILE LIGHTING YOUR CAMP STOVE. KEEP YOUR FACE AND BODY A
SAFE DISTANCE (AT LEAST 18 INCHES / 457 MM) FROM THE COOKING SURFACE WHEN LIGHTING YOUR STOVE BY MATCH.
8. IF THE BURNER GOES OUT DURING OPERATION, TURN THE CONTROL KNOBS TO THE "OFF" POSITION. WAIT FIVE MINUTES
BEFORE ATTEMPTING TO RELIGHT TO ALLOW ANY ACCUMULATED GAS TO DISSIPATE. IF THE BURNER DOES NOT LIGHT OR
IF THE ABOVE POINTS DO NOT WORK, SEE TROUBLESHOOTING.
SLIGHT YELLOW
SLIGHT BLUE
DARK BLUE
FLAME
BURNER

11
www.thiessens.com
SHUTTING OFF YOUR UNIT
1. WHEN FINISHED COOKING, TURN GAS CYLINDER VALVE TO THE CLOSED POSITION, AND ALLOW THE REGULATOR KNOB TO POP OUT.
THIS SAFETY FEATURE LOCKS THE REGULATOR KNOB TO ENSURE THAT THE GAS IS NO LONGER FLOWING.
2. TURN CONTROL KNOBS TO THE “OFF” POSITION.
NOTE: A “POOF” SOUND IS NORMAL AS THE LAST OF THE LP GAS IS BURNED.
3. DISCONNECT GAS SUPPLY BY FOLLOWING THE DISCONNECT A GAS CYLINDER INSTRUCTIONS.
WARNING: ALLOW THE STOVE TO COOL COMPLETELY, AND REMOVE THE GAS CYLINDER, BEFORE MOVING, TRAVEL, OR
FOR STORAGE.
COLLAPSING FOR TRANSPORT
YOUR STOVE CAN QUICKLY AND EASILY BE COLLAPSED FOR STORAGE AND EASY TRANSPORTATION. TO FOLD AND SECURELY TRANSPORT
YOUR STOVE, SIMPLY FOLLOW THE BELOW INSTRUCTIONS.
IMPORTANT: ALWAYS ENSURE THE STOVE IS COMPLETELY COOLED, DISCONNECTED FROM A GAS SUPPLY, AND THAT ALL
ACCESSORIES ARE REMOVED FROM THE STOVETOP AND SIDE TABLE SURFACES.
1. FOLD IN THE WIND SHIELD SIDE WINGS, THEN FOLD DOWN ALL WIND SHIELD PANELS SO THEY ARE FLAT ON THE STOVETOP.
2. HOLDING THE SIDE TABLE WITH ONE HAND, UNHOOK THE LOCKING PLATE FROM THE LOCKIN PIN ON THE SUPPORT FRAME. SWING
THE SUPPORT FRAME OUTWARD, THEN LAY FLAT ONTO THE SIDE TABLE.
3. FLIP THE SIDE TABLE/SUPPORT FRAME OVER AND ONTO THE STOVE TOP, AND FASTEN THE BRACKET WITH THE DRAW LATCH. THE
BRACKET IS SECURE ONCE THE SAFETY CATCH OF THE DRAW LATCH IS LOCKED. THE SAFETY CATCH PREVENTS THE DRAW LATCH
FROM OPENING.
4. FOLD IN THE FRONT COVER.
NOTE: THE FRONT COVER WILL ONLY CLOSE IF THE BURNER CONTROL KNOBS ARE IN THE "OFF" POSITION.
5. CAREFULLY, TIP AND PLACE THE CAMP STOVE ON ITS SIDE (HORIZONTAL) TO FOLD IN THE SUPPORT LEGS. PUSH DOWN ON THE
LOCKING PIN TO RELEASE EACH SUPPORT LEG. FOLD IN EACH OF THE FOUR SUPPORT LEGS UNTIL THE LOCKING PINS LOCK.
6. MOVE THE CAMP STOVE TO DESIRED LOCATION, OR TO VEHICLE FOR TRANSPORT, IMMEDIATELY TO AVOID INJURY TO YOURSELF OR
DAMAGE TO THE UNIT.
IMPORTANT: TAKE SPECIAL CARE OF THE REGULATOR AND HOSING AS YOU COLLAPSE AND TRANSPORT THIS UNIT.

12
THIESSENS : Authentic Pursuit Equipment
CARE AND MAINTENANCE
CHECKING THE GAS LEVEL
• TO CHECK THE AMOUNT OF FUEL IN A GAS CYLINDER, THE CAMP STOVE MUST BE IN OPERATION. PLACE YOUR HAND AT THE TOP OF
THE GAS CYLINDER AND SLOWLY MOVE DOWN THE SIDE UNTIL THE GAS CYLINDER FEELS COOL TO THE TOUCH. THIS WILL INDICATE
THE APPROXIMATE AMOUNT OF GAS IN YOUR GAS CYLINDER; IF ¾ EMPTY, REPLACE WITH A FULL GAS CYLINDER.
IMPORTANT: DO NOT USE CHARCOAL BRIQUETTES OR ANY FLAMMABLE MATERIAL WITH YOUR CAMP STOVE. USE OF SUCH
MATERIAL WILL VOID YOUR WARRANTY AND MAY LEAD TO A FIRE, EXPLOSION AND BODILY HARM.
BURNER COMPONENTS
• CLEAN THE BURNER WHENEVER HEAVY BUILD-UP IS FOUND, TO ENSURE THAT THERE ARE NO SIGNS OF BLOCKAGE (DEBRIS,
INSECTS) ON THE BURNER TUBE OR IN THE BURNER PORTHOLES. AFTER PERIODS OF STORAGE, SPIDERS OR SMALL INSECTS CAN
BUILD NESTS, WEBS, AND LAY EGGS IN THE BURNER TUBE, OBSTRUCTING THE FLOW OF GAS TO THE BURNER. A CLOGGED TUBE CAN
LEAD TO A FIRE BENEATH THE APPLIANCE. IF STORING THE CAMP STOVE, OR BEFORE AN EXTENDED PERIOD OF NON-USE, REMOVE
THE BURNER AND WRAP WITH ALUMINUM FOIL TO REDUCE THE RISK OF INSECTS ENTERING THE BURNER HOLES.
• THE BURNER HAS BEEN PRESET FOR OPTIMAL FLAME PERFORMANCE. A BLUE FLAME, POSSIBLY WITH A SMALL YELLOW TIP, IS THE
RESULT OF THE OPTIMAL AIR AND GAS MIXTURE. IF FLAMES ARE EXCESSIVELY YELLOW, ORANGE OR IRREGULAR, CLEAN THE OIL
AND FOOD DEPOSITS ON THE BURNER SURFACE AND THE BURNER PORTHOLES TO INCREASE AIRFLOW.
• IF THE BURNER IS REMOVED DURING CLEANING OR
MAINTENANCE, ENSURE THAT BURNER IS REPLACED IN THE
PROPER POSITION WITH THE BURNER PORTHOLES FACING
UPWARD. NOTE ILLUSTRATION SHOWN. WRONG PLACEMENT
WILL LEAD TO FIRE, EXPLOSION AND BODILY HARM.
STOVE EXTERIOR & SIDE TABLE
• USE A COVER TO PROTECT YOUR CAMP STOVE FOR COMPLETE PROTECTION! A COVER IS YOUR BEST PROTECTION AGAINST WEATHER
AND OUTSIDE POLLUTANTS. WHEN NOT IN USE OR FOR LONG-TERM STORAGE, KEEP THE UNIT UNDER A COVER IN A GARAGE OR
SHED, WITH THE GAS CYLINDER REMOVED (CYLINDERS MUST BE STORED OUTDOORS).
CLEANING TIME TABLE (NORMAL USE)
COMPONENT PART CLEANING FREQUENCY CLEANING METHOD
BURNER TUBE, PORTHOLES EVERY 5-6 USES DUST, SCRUB PAD & SOAPY WATER
BURNERS EVERY 5-6 USES SCRUB PAD & SOAPY WATER
SIDE TABLE, SUPPORT FRAME,
SUPPORT LEGS
AS NEEDED NON-ABRASIVE CLOTH & SOAPY WATER
BURNER PORTHOLES

13
www.thiessens.com
TROUBLESHOOTING
PROPER CLEANING AND MAINTENANCE WILL PREVENT COMMON OPERATIONAL PROBLEMS. WHEN YOUR CAMP STOVE IS OPERATING
POORLY, OR ON A LESS FREQUENT BASIS, THE FOLLOWING TROUBLESHOOTING TIPS MAY BE HELPFUL.
WARNING: ALWAYS ENSURE THE STOVE IS COMPLETELY COOLED TO AVOID INJURY.
PROBLEM CAUSE SOLUTION
BURNER WILL NOT LIGHT THE IGNITION WIRE IS BROKEN CONTACT Customer care FOR ASSISTANCE OR A REPLACEMENT PART.
NO IGNITER SPARK ON ELECTRODE ADJUST THE ELECTRODE. CONTACT Customer care FOR ASSISTANCE OR A
REPLACEMENT PART.
NO GAS SUPPLIED CHECK THE REGULATOR VALVE. CHECK CONNECTION FOR LEAK.
GREASE FIRE / FREQUENT
FLARE-UPS
GRILLING FATTY MEATS GRILL FATTY MEATS WHEN THE COOKING SURFACE IS COLD, AND THE KNOBS ARE
ON THE “LOW” SETTING.
COOKING TEMPERATURE ATTEMPT COOKING AT A LOWER TEMPERATURE. GREASE DOES HAVE A FLASH POINT.
KEEP THE TEMPERATURE UNDER 176°C / 350°F WHEN COOKING HIGHLY GREASY
FOOD.
WATER SPRAYED ON GAS FLAMES DO NOT SPRAY WATER ON GAS FLAMES.
BURNER BLOWS OUT NO GAS FLOW CHECK GAS FUEL CONNECTION, AND ENSURE IT IS OPEN. REPLACE GAS CYLINDER
IF EMPTY.
GUSTING OR HIGH WINDS TURN FRONT OF CAMP STOVE AWAY FROM WIND OR INCREASE FLAME HEIGHT.
LOW HEAT ON “HIGH” PORTS BLOCKED CLEAR PORTS OF ANY OBSTRUCTIONS.
GAS CYLINDER EMPTY REFILL THE GAS CYLINDER.
GAS LEAKAGE IMPROPER INSTALLATION TURN THE REGULATOR KNOB TO THE OFF POSITION, AND ALLOW THE REGULATOR
KNOB TO POP OUT. REMOVE THE GAS CYLINDER. RE-INSTALL AND TIGHTEN.
PERFORM LEAK TEST TO ENSURE PROPER SEAL. REPLACE GAS CYLINDER IF
DAMAGED.
SEAL FAILURE GAS CYLINDER HAS CORRODED, RUSTED, OR HAS BEEN MISHANDLED. REPLACE
GAS CYLINDER.
REGULATOR FAILURE REGULATOR NEEDS TO BE REPLACED. CONTACT Customer care FOR A REPLACEMENT
PART.
BURNER FLAMES ARE
YELLOW OR ORANGE
POOR AIR FLOW CHECK BURNER TUBE AND BURNER PORTS FOR SPIDER WEBS OR OTHER
OBSTRUCTIONS. FOLLOW CARE AND MAINTENANCE INSTRUCTIONS TO CLEAN THE
BURNER TUBE.
BURNER OBSTRUCTION
GREASE CUP IS FULL, SPILLING EMPTY GREASE CUP AND RE-INSTALL. FOLLOW CARE AND MAINTENANCE
INSTRUCTIONS.
REGULATOR VALVE IS OFF CHECK THE REGULATOR VALVE CONNECTION TO THE GAS CYLINDER. REMOVE, THEN
REINSTALL. PERFORM LEAK TEST.
BURNER IS DIRTY TURN REGULATOR KNOB TO HIGH FOR FIVE MINUTES, AND BURN-OFF THE UNIT.
FOLLOW CARE AND MAINTENANCE INSTRUCTIONS.

14
THIESSENS : Authentic Pursuit Equipment
1
4
6
8
7
9
2
3
5
11
10
11
12
13
14
19
15
17
18
16
REPLACEMENT PARTS
1
8
4
56
7
3
2
A
B
NOTE: Due to ongoing product development, parts are subject to change without notice.
PART DESCRIPTION
1 Support Frame B (x1)
2 Bracket A (x1)
3 Bracket B (x1)
4 Side Table (x1)
5 Side Table Handle (x1)
6 Side Table Bracket (x1)
7 Wind Shield Assembly (x1)
8 Stove Firebox (x1)
9 Clasp (x1)
10 Fixed Leg (x4)
11 Adjustable Leg (x4)
12 Burner (x3)
13 Air Handle (x3)
14 Valve Assembly (x1)
15 Regulator With Hose (x1)
16 Control Panel (x1)
17 Control Knob Bezel (x3)
18 Control Knob (x3)
19 Front Cover (x1)
A Screw (x12)
B Step Screw (x2)

15
www.thiessens.com
WARRANTY
CONDITIONS
ALL GAS CAMP STOVES BY THIESSENS, MANUFACTURED BY DANSONS, CARRY A LIMITED WARRANTY FROM THE DATE OF SALE BY THE
ORIGINAL OWNER. THE WARRANTY COVERAGE BEGINS ON THE ORIGINAL DATE OF PURCHASE AND PROOF OF DATE OF PURCHASE, OR
COPY OF ORIGINAL BILL OF SALE, IS REQUIRED TO VALIDATE THE WARRANTY. CUSTOMERS WILL BE SUBJECT TO PARTS, SHIPPING, AND
HANDLING FEES IF UNABLE TO PROVIDE PROOF OF THE PURCHASE OR AFTER THE WARRANTY HAS EXPIRED. DANSONS CARRIES A
TWO (2) YEAR WARRANTY AGAINST DEFECTS AND WORKMANSHIP ON ALL PARTS. DANSONS WARRANTS THAT ALL PART(S) ARE FREE
OF DEFECTS IN MATERIAL AND WORKMANSHIP, FOR THE LENGTH OF USE AND OWNERSHIP OF THE ORIGINAL PURCHASER. WARRANTY
DOES NOT COVER DAMAGE FROM WEAR AND TEAR, SUCH AS SCRATCHES, DENTS, DINGS, CHIPS OR MINOR COSMETIC CRACKS. THESE
AESTHETIC CHANGES OF THE CAMP STOVE DO NOT AFFECT ITS PERFORMANCE. REPAIR OR REPLACEMENT OF ANY PART DOES NOT
EXTEND PAST THE LIMITED WARRANTY BEYOND THE TWO (2) YEAR FROM DATE OF PURCHASE.
DURING THE TERM OF THE WARRANTY, DANSONS’ OBLIGATION SHALL BE LIMITED TO FURNISHING A REPLACEMENT FOR DEFECTIVE AND/
OR FAILED COMPONENTS. AS LONG AS IT IS WITHIN THE WARRANTY PERIOD, DANSONS’ WILL NOT CHARGE FOR REPAIR OR REPLACEMENT
FOR PARTS RETURNED, FREIGHT PREPAID, IF THE PART(S) ARE FOUND BY DANSONS’ TO BE DEFECTIVE UPON EXAMINATION. DANSONS’
SHALL NOT BE LIABLE FOR TRANSPORTATION CHARGES, LABOR COSTS, OR EXPORT DUTIES. EXCEPT AS PROVIDED IN THESE CONDITIONS
OF WARRANTY, REPAIR OR REPLACEMENT OF PARTS IN THE MANNER AND FOR THE PERIOD OF TIME MENTIONED HERETOFORE SHALL
CONSTITUTE THE FULFILLMENT OF ALL DIRECT AND DERIVATE LIABILITIES AND OBLIGATIONS FROM DANSONS TO YOU. DANSONS TAKES
EVERY PRECAUTION TO UTILIZE MATERIALS THAT RETARD RUST. EVEN WITH THESE SAFEGUARDS, THE PROTECTIVE COATINGS CAN BE
COMPROMISED BY VARIOUS SUBSTANCES AND CONDITIONS BEYOND DANSONS’ CONTROL. HIGH TEMPERATURES, EXCESSIVE HUMIDITY,
CHLORINE, INDUSTRIAL FUMES, FERTILIZERS, LAWN PESTICIDES AND SALT ARE SOME OF THE SUBSTANCES THAT CAN AFFECT METAL
COATINGS. FOR THESE REASONS, THE WARRANTY DOES NOT COVER RUST OR OXIDIZATION, UNLESS THERE IS LOSS OF STRUCTURAL
INTEGRITY ON THE CAMP STOVE COMPONENTS. SHOULD ANY OF THE ABOVE OCCUR, KINDLY REFER TO THE CARE AND MAINTENANCE
SECTION TO PROLONG THE LIFESPAN OF YOUR UNIT. DANSONS RECOMMENDS THE USE OF A COVER WHEN THE CAMP STOVE IS NOT IN USE.
THIS WARRANTY IS BASED ON NORMAL DOMESTIC USE AND SERVICE OF THE CAMP STOVE AND NEITHER LIMITED WARRANTY COVERAGE’S
APPLY FOR A CAMP STOVE WHICH IS USED IN COMMERCIAL APPLICATIONS.
EXCEPTIONS
THERE IS NO WRITTEN OR IMPLIED PERFORMANCE WARRANTY ON THIESSENS PRODUCTS, AS THE MANUFACTURER HAS NO CONTROL
OVER THE INSTALLATION, OPERATION, CLEANING, MAINTENANCE OR THE TYPE OF FUEL BURNED. THIS WARRANTY WILL NOT APPLY NOR
WILL DANSONS ASSUME RESPONSIBILITY IF YOUR APPLIANCE HAS NOT BEEN INSTALLED, OPERATED, CLEANED AND MAINTAINED IN
STRICT ACCORDANCE WITH THIS OWNER’S MANUAL. ANY USE OF GAS NOT OUTLINED IN THIS MANUAL MAY VOID THE WARRANTY. THE
WARRANTY DOES NOT COVER DAMAGE OR BREAKAGE DUE TO MISUSE, IMPROPER HANDLING OR MODIFICATIONS. NEITHER DANSONS, OR
AUTHORIZED THIESSENS DEALER, ACCEPTS RESPONSIBILITY, LEGAL OR OTHERWISE, FOR THE INCIDENTAL OR CONSEQUENTIAL DAMAGE
TO THE PROPERTY OR PERSONS RESULTING FROM THE USE OF THIS PRODUCT. WHETHER A CLAIM IS MADE AGAINST DANSONS BASED
ON THE BREACH OF THIS WARRANTY OR ANY OTHER TYPE OF WARRANTY EXPRESSED OR IMPLIED BY LAW, THE MANUFACTURER SHALL
IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR OTHER DAMAGES OF ANY NATURE WHATSOEVER IN EXCESS
OF THE ORIGINAL PURCHASE OF THIS PRODUCT. ALL WARRANTIES BY MANUFACTURER ARE SET FORTH HEREIN AND NO CLAIM SHALL BE
MADE AGAINST MANUFACTURER ON ANY WARRANTY OR REPRESENTATION. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS OF IMPLIED WARRANTIES, SO THE LIMITATIONS OR EXCLUSIONS SET
FORTH IN THIS LIMITED WARRANTY MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY
HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
WARRANTY SERVICE
CONTACT YOUR NEAREST THIESSENS DEALER FOR REPAIR OR REPLACEMENT PARTS. DANSONS REQUIRES PROOF OF PURCHASE TO
ESTABLISH A WARRANTY CLAIM; THEREFORE, RETAIN YOUR ORIGINAL SALES RECEIPT OR INVOICE FOR FUTURE REFERENCE. THE SERIAL
AND MODEL NUMBER OF YOUR UNIT CAN BE FOUND ON THE BACK OF THE UNIT. RECORD NUMBERS BELOW AS THE LABEL MAY BECOME
WORN OR ILLEGIBLE.
MODEL SERIAL NUMBER
DATE OF PURCHASE AUTHORIZED DEALER
CONTACT CUSTOMER CARE
IF YOU HAVE ANY QUESTIONS OR PROBLEMS, CONTACT CUSTOMER CARE.
WWW.THIESSENS.COM | TOLL-FREE: 1-877-972-5742

780210125VCM
CONTACT CUSTOMER CARE
IF YOU HAVE ANY QUESTIONS OR PROBLEMS,
CONTACT CUSTOMER CARE.
WWW.THIESSENS.COM | TOLL-FREE: 1-877-972-5742
WARNING: COMBUSTION OF PROPANE GAS CAN EXPOSE YOU TO CHEMICALS
INCLUDING FORMALDEHYDE, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER, AND CARBON MONOXIDE, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. FOR MORE INFORMATION GO TO
WWW.P65WARNINGS.CA.GOV
602210621UMV
MADE IN CHINA