Thomasville Summer Silhouette 12255-011 User manual

Page 1 of 2
Assembly Instructions Summer Silhouette
TM
Glass-Top Dining Table Model # 12255-011
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts that may have come
loose inside the carton during shipment. Please read all instructions carefully before starting the assembly process.
CAUTION: Some items and/or the components are cumbersome and heavy. Therefore, the assistance of one or more people
is recommended in order to prevent personal injury and insure that the item and/or its components are not damaged during the
assembly process. Perform all assembly steps on a flat, soft, non-abrasive surface to avoid scratching the finish. Do not over-
tighten the screws or bolts.
Hardware & Parts List
No. Description Picture Qty
A1 Table Top (with glass packed inside)
A2 Table Top Frame (with glass removed)
1
B Table Legs
4
C Screws 1/4”*20 24
D Washers φ6.5*1.0 24
E Screw Covers 1/4”
24
F Hex Key 1
G Touch-up Paint
1
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !

Page 2 of 2
Assembly Instructions Summer Silhouette
TM
Glass-Top Dining Table Model # 12255-011
1. Carefully remove the glass panels that were packed inside of the tabletop frame (A1) for shipping. Next, carefully place the
tabletop frame (A2 – with the glass removed) upside down on a flat, soft, non-abrasive surface. Place a table leg (B) in the corner
of the table top frame bottom rim and align the holes in the rim with the holes in the table leg. Insert the screws (C) with washer
(D) through the holes in the corner of the table rim and screw them into the holes in the table leg. Then, insert screws (C) with
washer (D) through the holes on the outside of the table legs and screw them into the holes in the table rim. Do NOT
completely tighten any of the screws until all six screws have been inserted. After all six screws have been inserted, use the hex
key to securely tighten each screw. Install a screw cover on each of the six screws. See Figure 1.
Repeat this same procedure for the other three legs.
2. After all four legs have been securely attached and the screw
covers installed, carefully turn the table over into the upright position.
See Figure 2.
Figure 2
3.
Carefully place the glass panels, that were removed in Step 1, into the
openings in the table top frame. See Figure 3.
Note: Please keep the touch-up paint (G) for future use on your table if
needed.
Figure 3
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !
Figure 1

Page 1 of 2
Assembly Instructions Summer Silhouette
TM
Dining Chair Model # 12255-011
Thank you for purchasing this quality product. Be sure to check all packing materials carefully for small parts that may have come
loose inside the carton during shipment. Please read all instructions carefully before starting the assembly process.
CAUTION: Some items and/or the components are cumbersome and heavy. Therefore, the assistance of one or more people
is recommended in order to prevent personal injury and insure that the item and/or its components are not damaged during the
assembly process. Perform all assembly steps on a flat, soft, non-abrasive surface to avoid scratching the finish. Do not over-
tighten the screws or bolts.
Note: The quantities listed in the
Hardware & Parts List are the totals
for all six dining chairs.
Hardware & Parts List
No. Description Picture Qty
A Chair Frames
6
B Chair Seats
6
C Long Screws 1/4”*20 24
D Short Screws 1/4”*15 12
E Washers φ6.5*1.0 36
F Screw Covers 1/4”
36
G Seat Cushions 6
H Back Cushions
6
I Hex Key
3
J Touch-up Paint
1
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !

Page 2 of 2
Assembly Instructions Summer Silhouette
TM
Dining Chair Model # 12255-011
1. Place the chair frame upside down on a flat, soft, non-
abrasive surface. Attach the chair seat (B) to the chair frame
(A) by aligning the holes on the chair seat frame rails with
those on the chair frame back rail and front legs. Insert the
two short screws (D) with washers (E) through the bottom
of the chair frame back rail into the holes in the bottom of
the chair seat back rail. Insert two long screws (C) with
washers (D) through the inside of the corners of the chair
seat frame front rail and into the holes in the left leg. Repeat
this procedure to attach the chair seat to the right leg. Do
NOT completely tighten the screws until all screws have
been inserted. After inserting all screws, securely tighten the
screws using the hex key (I). Install a screw cover (F) on all
of the screw heads both (C & D). See Figure 1.
Figure 1
2. After securely attaching the chair seat to the seat
frame, carefully turn the chair into the upright position
as indicated in Figure 2. Place the seat cushion (G)
and back cushion (H) on the dining chair as shown in
Figure 3. Secure the seat cushions to the chair frame
with the Velcro straps.
Repeat this same procedure to assemble the remaining
dining chairs.
Note: Please keep the touch-up paint (J) for future
use on your chairs if needed.
Figure2 Figure3
! KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE !