Thomasville TV-20 User manual

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
Description
Item No.
: COTTAGE 60 INCH TV STAND
: TV-20

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
H
Side shelf
(L&R)
2
B
Center
panel
1
I
Center shelf
2
C
Door (L-R)
2
J
Back panel (L
& R)
2
D
Vertical
panel
(L-R)
2
K
Center back
panel (L)
1
E
Side panel
2
L
Center back
panel (R)
1
F
Bottom
panel
1
M
H-Connector
1
G
Center
divider
1
N
Leg
5

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 30mm)
24
8
Door pin
(5.2/13x1.2mm)
(7 x 10mm)
4
2
Spring washer
(ɸ6.5 x 11mm)
24
9
Magnet
2
3
Flat washer
(ɸ6.5 x 13mm)
24
10
Bracket
16
4
Long screw
(M4 x 30mm)
2
11
Steel band
1
5
Short screw
(M3.5 x 15mm)
22
12
Allen key
(M4 x 80mm)
1
6
Short pan head screw
(M3 x 15mm)
10
13
Wooden knob
(38 x 30mm)
2
7
Long pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
2
METAL KNOB
(30 x 30mm)
GOES WITH
FINISHED ITEM
ONLY.
2
STEP 1
Attach side panel (E) and center divider (G) to top (A) with bolts (1) and washers (2) and (3) as shown
below. Tighten with Allen key (12).

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 5 -
STEP 2
Attach side panel (E) to top (A) and center panel (B) with bolts (1) and washers (2) and (3). Then
attach center panel (B) to center divider (G) with bolts (1) and washers (2) and (3) as shown below.
Tighten with Allen key (12).
STEP 3
Attach vertical panels (D) to center panel (B) with bolts (1) and washers (2) and (3) as shown below.
Tighten with Allen key (12).

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 6 -
STEP 4
Attach doors (C) to center panel (B) and bottom panel (F) with door pins (8) as shown below.
Attach bottom panel (F) to side panels (E) and vertical panels (D) with bolts (1) and washers (2) and (3)
as shown below. Tighten with Allen key (12).
STEP 5
Slide center back panels (K) and (L) into grooves of vertical panels (D) and H-connector (M), then
attach H-connector (M) to bottom panel (F) with screw (4) as shown belown. Tighten with a
screwdriver.
Slide back panels (J) into grooves of vertical panels (D) and side panels (E). Then attach back panels
(J) to bottom panel (F) with screws (6) as shown below. Tighten with a screwdriver.

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 7 -
STEP 6
Attach legs (N) by screwing them into bottom panel (F) as shown below.
STEP 7
Insert brackets (10) into the unit as shown below. Place shelves (H) and (I) on the brackets and attach
with screws (5). Tighten with a screwdriver.
Attach magnets (9) to vertical panels (D) with screws (5) as shown below. Tighten with a screwdriver.

ITEM NO. : TV-20
ISSUED MAR 01, 2016
Printed in Vietnam
- 8 -
STEP 8
Attach steel band (11) to the unit with screws (5) and attach steel band (11) to the wall with screw (4)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.
Attach knobs (13) to doors (C) with pan head screws (7) as shown below. Tighten with a screwdriver.