Three Sixty Kirra KIR100 Series User manual

The Kirra
Owner’s Manual
Please read and keep these instructions as they contain assembly,
warranty, maintenance and service information.
Version:
Date:
1.2
August 2020
100” / 254cm DC Ceiling Fan
Model No. KIR100**
Net Weight: 10.7 kg
Gross Weight: 12.1 kg

2
ThreeSixty Ceiling Fans
Fan Technology That’s Innovative and Reliable
ThreeSixty Ceiling Fans is proud of its range of ceiling ceiling fans, accessories and lighting
products. We believe these are the leading products in their category, reecting over 40 years
collective Australian experience in design, development, manufacturing and distribution of
electronics and electrical equipment.
The Kirra ceiling fan is the ultimate statement piece - at an incredible 100 inches (254 cm)
blade span, the meticulously sculpted timber blades are sure to impress in any space. Utilising
the latest DC motor technology, the Kirra is able to propel the sweeping blades leveraging the
high torque, low power consumption motor stack.
Our manufacturing is subject to strict quality control and we back our products with a plain-
English warranty. Any problem caused by a fault in the product will be xed or replaced with
the least possible inconvenience.
We welcome feedback and suggestions. By listening to our customers we aim to continuously
improve our products and services.
Electricians and installers:
We are here to help you. Please call our
support line if you have any questions or
need assistance with installing or wiring
the product.
Customers and purchasers:
Please call us if you have any questions
about your fan or would like advice on the
best way to use your fan to save energy.
ThreeSixty Fans Support can be contacted by calling 1300 469 326, visting our website at
https://360fans.com.au or emailing our team at [email protected]

3
Important Safety Instructions
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying
assembly diagrams.
2. Before servicing or cleaning unit, switch power o at fuse box / circuit breaker and lock box (disconnecting
means to prevent power from being switched on accidentally).
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn o the power
to the ceiling fan before servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
6. Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities.
7. Contact your local government for information regarding the collection systems available.
8. If electrical appliances are disposed of in landlls or dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-being.
9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
10. Children should be supervised to ensure that they do not play with the appliance.
WARNING: To avoid re, shock and serious personal injury, follow these instructions.
Additional Safety Instructions
1. To avoid possible shock, be sure electricity is turned o at the fuse box before wiring, and do not operate fan
without blades.
2. All wiring and installation procedures must comply with AS/NZS 3000 Wiring Rules and any other local
regulations. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical
installation must be made by a licensed electrician.
3. The fan base must be securely mounted and capable of reliably supporting at least four times the weight
of the ceiling fan. The installation and replacement of the suspension system must be completed by the
manufacturer, its service agent or a suitably qualied person.
4. The fan must be mounted with the fan blades at least 2.1 meter (lowest edge) from the oor to comply with
safety regulations and to prevent accidental contact with the fan blades.
5. Follow the recommended instructions for the proper method of wiring this ceiling fan.
6. This fan must be installed with an isolation switch or a device to disconnect all poles.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories
designated specically for use with this product. Using parts and/or accessories not designated for use with this
product will void your warranty and could result in personal injury or property damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (ange or blade holder) when
installing the brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating
fan blades.
WARNING: This fan MUST be installed with an easily accessible isolating device to disconnect all poles of the fan
from the main supply.
WARNING: If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the
manufacturer, its service agent or suitably qualied persons.
IMPORTANT: This product must be
installed by a licensed electrician and
comply with AS/NZS 3000 Wiring Rules
and any other local regulations.

4
Supplied parts
Tools and materials required
Installation issues, missing or damaged parts
• One fan DC motor assembly
• One hanger bracket tted with terminal block
• One top canopy
• One set of blades and blade cover
• One screw pack
• One installation booklet
• One remote control with preset remote receiver
• Phillips screwdriver
• Blade screwdriver
• Small electrical screwdriver
• Electrical pliers
• Step ladder
• Wiring supplies as required by current electrical practices
• If an extension rod is used it is supplied with an extension wiring loom
Before starting the assembly and installation of your fan please ensure the safety instructions
have been read and understood.
If you have any diculty installing your fan or if you are unfortunate enough to nd that your fan
has been dispatched with parts missing or damaged, please contact our help line on 1300 469
326. We will provide help and/or replacement parts to you immediately.
In any communication with us please quote your model number and nish (colour) of the unit,
along with as much information on the missing or damaged part(s) as possible.

5
Exploded Fan View & Parts
CEILING
HANGER BRACKET
WOOD SCREW
RECEIVER
HANGER BALL
CANOPY
SET SCREWS
BLADE HOLDER PLATE
BLADE SCREWS
BLADES
REMOTE CONTROL
WITH WALL BRACKET,
2X AAA BATTERIES
BLADE COVER

6
Installing the fan
1. Hanger bracket installation
All electrical work should only be undertaken by a licensed electrician and after disconnection
of the power by removing fuses or turning o the circuit breaker to ensure all poles isolation of
the electrical supply.
The following steps will guide you to a successful installation:
1. Hanger bracket installation
2. Seat ceiling fan motor into hanger bracket and insert remote receiver module
3. Remote control installation and wiring, install ceiling canopy
4. Install ceiling fan blades
5. Attach the blade cover
The hanger bracket should be screwed on to a rm at
surface. The xing location must be able to withstand
four times the static weight of the fan. Due to the size
of the Kirra ceiling fan, four (4) wood screws provided
should be used to securely mount the hanger bracket.
2. Seat ceiling fan and insert remote receiver
Slide the remote control receiver module
into the gap in the hanger bracket as shown.
Carefully store wiring within the bracket.
Beware of pinching wires.
Carefully lift the fan and seat the downrod
ball assembly on the hanger bracket. Be sure
the groove in the ball is lined up with the tab
on the hanger bracket. Do not pinch wires
between the ball and downrod assembly and
hanger bracket.

7
Yellow/Green(E)
Black (N)
Red (L)
L IN AC
N IN AC
House Supply Wires
Pink
Grey
Red
Blue
Brown
Yellow/Green(E)
Yellow/Green(E)
Pink
Grey
Red
Yellow/Green(E)
Yellow
Blue
Brown
Ceiling Fan
Hanger Bracket
1
2
3
Yellow/Green(E)
3. Remote control installation and wiring
WIRING INSTRUCTIONS: Ensure power is safely isolated before attempting any wiring.
Your fan is supplied with a radio frequency remote control unit and the fan can only be controlled
by remote control. IMPORTANT - This appliance must be earthed.
Step 1: Connect AC Power Supply to Terminal Block
Connect the AC household power supply wires from
the ceiling to the Hanger Bracket’s terminal block.
Connect the RED active wire to the connection labeled
‘L’. Connect the BLUE neutral wire to the connection
labeled ‘N’. Connect the YELLOW/GREEN earth wire to
the connection labeled with the Earth symbol.
Step 2: Connect Terminal Block to Receiver
Connect the 4 pin female plug coming from the remote
receiver with the male plug coming from the hanger
bracket terminal block.
Step 3: Connect Receiver to Ceiling Fan
Connect the 4 pin male plug coming from the remote
receiver with the 4 pin female plug coming from the
ceiling fan.
Step 4: Fit the ceiling canopy
Fit the ceiling canopy over the hanger bracket and fasten
the 2 set screws. The canopy should NOT touch the
ceiling - ensure a gap exists all the way around.
EXPLODED WIRING DIAGRAM:
Provided for clarity and to
help identify the correct
wires only.
SET
SCREWS

8
4. Install ceiling fan blades
5. Attach the magnetic blade cover
Install the ceiling fan blades using two (2) blade
screws and one (1) blade holder per blade. Do not
fully tighten the screws until all three blades have
been securely mounted.
Once all three blades are installed, rmly tighten all
screws to securely lock in the blades.
The magnetic blade cover can be installed by aligning it over the center screw ring and allowing
the magnet to snap into place.

9
Operating the handset (transmitter)
Learning / Pairing Setup
Fan On/O button
Fan Speed: Press and release immediately to turn on and set fan
speeds. Number 6 is the highest speed and Number 1 is the lowest.
The handset and remote control receiver module are pre-programmed at the factory and do
not normally require pairing. Should they not function when rst installed, or you wish to control
2 fans using 1 handset, or you need to pair a replacement handset please follow the below
procedure.
1. Ensure that AC power is isolated to the ceiling fan.
2. Restore AC power to the fan. Within 30 seconds PRESS and HOLD the Fan Power button for
5 seconds.
3. The remote control receiver module will beep twice to indicate the pairing process was
successful.
1
2
3 4
5
6
1H 4H 8H
Natural Wind mode: Fan speed changes automatically
within its range creating a gentle sea-breeze eect.
Reverse button: Press and release immediately to set fan
direction.
The fan will turn o after 1 hour automatically.
The fan will turn o after 4 hours automatically.
The fan will turn o after 8 hours automatically.
Battery Replacement:
2x 1.5V AAA
Installing wall mounted holder
Attach wall mounted remote holder/bracket
using the two screws provided.

10
ThreeSixty Fans - Plain English Warranty Terms
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a refund or replacement for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Mechanical and Structural Components
Your Product is covered against mechanical and structural defects that prevent it from working by a limited 36
month on-site warranty. This warranty covers only the product itself and excludes workmanship or materials
related to its installation or any modications. A major failure may be, for example, a motor defect preventing a
product from operating shortly after it was rst installed or if it was damaged while in the original packaging. If the
product stops working due to a mechanical or structural defect within the rst 36 months we will repair or replace
the product at our discretion.
Electronic Components
Your Product is covered against electronic defects that prevent it from working by a limited 12 month on-site
warranty. This warranty covers only the electronics supplied with the product and excludes workmanship or
materials related to its installation or any modications. A major failure may be, for example, a power module that
failed shortly after it was rst installed or if it was damaged while in the original packaging. If the product stops
working due to an electronic defect within the rst 12 months we will repair or replace the electronic part at our
discretion.
Compensation for reasonably foreseeable loss
Compensation normally comprises us paying associated labour costs to replace the defective product if it’s
installed within a reasonable distance from our repair agent. If beyond a reasonable distance (30km) you can
arrange your own electrician and we will compensate you for this up to a maximum of $115.50 inc GST. Note, we
do not pay extra for extended travelling time or additional costs when the job requires a longer than average time
to complete.
To prevent or limit costs you may incur for service calls, you must notify us of the intention to use your own
contractor and not engage one until we have spoken to them (to arrange parts that may be required). If the
problem is not a defect covered by our warranty terms you will have to pay all costs. To reduce cost and
inconvenience for all involved we will do our best to diagnose the fault and supply parts before the contractor visits
the site.
Eligibility for In-Home Service Calls
Hard wired electrical products must (by law) be installed by a licensed electrician. To obtain in-home warranty service
you must be able to provide a copy of the installing electricians invoice or the Certicate of Compliance
given to you when the product was rst wired up and tested. If you cannot provide this information we limit our
warranty to repair or replacement of the product at our workshop and you will bear the costs of removal, shipping
to us and reinstallation. We will pay the freight to send the rectied unit back to you.
Access to products
Products installed on ceilings 4m and above may require special access equipment or WH&S measures. All costs
for this equipment must be borne by the site owner and the ceiling height given when booking a service call. If a
service agent chooses not to access a product installed at height due to WH&S concerns the owner must remove
and reinstall the product at their own expense.
Isolation Switches
Australian Standards require our instructions to state an isolation switch must be tted. This allows the product
to be physically switched o in case of faults or to prevent damage from surges, lightning, etc. Emergency
disconnection and/or remote control re-programming that can’t be performed due to lack of an isolation switch is
not covered by warranty.
SHOULD THERE BE ANY INSTALLATION ISSUES OR DEFECTS PLEASE IMMEDIATELY CALL OUR
SUPPORT HELP LINE ON 1300 469 326 FOR ASSISTANCE AND ADVICE. DO NOT ATTEMPT TO
UNINSTALL OR REMOVE THE PRODUCT FROM THE CEILING UNLESS SPECIFICALLY ADVISED TO BY
THREESIXTY FANS AS THIS WILL CAUSE DELAYS DIAGNOSING AND RESOLVING THE ISSUE.

11
ThreeSixty Fans - Plain English Warranty Terms
Commencement
The warranty period begins from date of purchase and in-home warranty service is available only at the site of
original installation. If the product is installed as part of a project or development the warranty period commences
when the product was delivered to the site.
Damage
Damage from Force Majeure, electrical surges, wind, rain, lightning, power grid uctuations, water ingress,
condensation or use with incompatible power sources will not be rectied under warranty. Likewise solid state or
dimmer type speed controls may damage ceiling fans or cause them to make unusual noises. Genuine parts and
advice are available through our online and telephone support services.
Cosmetic defects
Carefully inspect your product prior to installation and notify us as soon as possible if there are cosmetic defects.
Cosmetic defects are generally not covered by warranty unless present when the product is initially unpacked.
Damage from being struck by objects or not being kept clean is not covered by warranty.
Corrosion
Deterioration of nishes, including rusting, pitting, corrosion, fading, tarnishing or peeling is not covered by warranty
beyond six months. Products specied as corrosion resistant or made from Stainless Steel are not corrosion
proof and will discolour or deteriorate if not cleaned. As a guide, maintain your product as you would your kitchen
appliances (clean every 3 months).
Noise
Signals sent through the power grid by the electricity supplier may cause intermittent noises in your product.
These noises are not the result of a fault and lters to reduce this noise may be available at additional expense.
Clicking, ticking and creaking noises from fans are usually caused by the mounting bracket not being correctly
attached or when blades screws are loose. Only use the hardware provided to install ceiling fans. If the mounting
bracket is attached using counter-sunk screws it will work loose and cause unwanted noise and movement in your
fan. Wooden bladed fans may need their blade screws periodically tightened. Unless a product is defective noise
will not be rectied under warranty.
Wobbling
Wobbling is generally not caused by a defective fan but by air currents in the room. After a fan has been running
for a long period it will cause air currents to form and, depending on the shape of the room and its furnishings, the
air returning to the fan may be uneven.
Improper mounting will also cause a fan to wobble. Every mounting bracket screw must be secured to solid
materials in the ceiling. Metal C section rafters may need to be doubled to form a box section to prevent exing.
Foam sandwich ceiling panels will require reinforcing to stop exing. Unless a product is defective wobbling will
not be rectied under warranty.
Airow
The amount of airow produced by a fan is dependent on where it’s installed because room shape, mounting
height and furnishings will aect the perceived air movement. A product is deemed to be functioning normally if it
is running within 15% of the specied RPM when installed.
Purchase Date:
Product Model:
License Number:
Light Model:
Ceiling Height:
Seller Name:
Installed By:
Contact number:
Remote Control:
Isolation Switch: Yes No