Three Sixty Kensington DC KEN720BLED Setup guide

OWNERS INSTRUCTION MANUAL
183CM/72”
LT
CAUTION
READ INSTRUCTIONS CAREFULLY FOR SAFE
INSTALLATION AND FAN OPERATION. IF UNSURE CONSU
A QUALIFIED ELECTRICIAN
SUITABLE FOR 230V/50 CYCLE ELECTRICAL SUPPLY
WEIGHT OF FAN, N.W.: 11.8 KGS, G.W.: 13.2 KGS
7

Table of Contents ...............................
Safety Information ..............................
Pre-installation ..................................
Assembly .......................................
Operation .......................................
Care and Cleaning ..............................
Troubleshooting ................................
2
Table of Contents
2
2
3
5
12
13
14
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
To ensure the success of the installation be sure to read the instructions and study the diagrams thoroughly before
commencing.
This fan MUST be installed with an easily accessible isolated device to disconnect all poles of the fan from the
main supply.
Electrical installation must be performed by a licensed electrician.
Do not connect the fan motor to a dimmer switch (solid state). This may give an unsatisfactory performance (motor
hum) and cause damage to the motor.
The fan must be earthed.
All electrical work should only be undertaken after disconnection of the power by removing fuses or turning off the
circuit breaker to ensure all pole isolation of the electrical supply. If you are in any doubt the services of a qualified
electrician should be sought to ensure that all work is carried out in accordance with AS/NZS 3000 Wiring Rules,
current good practice and other national and local electrical codes.
The fixing point for the fan must be able to support a weight of 48kg. Net weights can be found on the bottom of
the unit’s box. If you are mounting the fan to a ceiling junction box, the box and it’s fixing must be able to support
the moving weight of the fan and must not twist or work loose.
Make sure that your installation site will not allow the rotating fan blades to come into contact with any object and
that there is a minimum clearance of 150mm from the blade tip to the wall or ceiling. Please note that the bigger
this clearance is the better the airflow from your fan will be. Ensure the blades are mounted at a minimum height of
2.1 meters from the floor when the fan is installed.
Electrical installation must be performed by a licensed electrician.
Do not insert anything into the fan blades while the fan is operating. This will damage the blades and upset the
balance of the unit causing the unit to wobble.
After the fan is completely installed make sure that all connections are secure and tight to prevent any problems.
Because of the fan’s natural movement, some connections may loosen. Check the support connections, brackets
and blade attachments twice a year to make sure they are all secure. If they are loose tighten with a screwdriver.
( It is not necessary to take the fan down from the ceiling )
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Safety Information
NOTE: The important safeguards and instructions given in this manual are not meant to cover all possible conditions
and situations that may occur. It must be understood that common sense, caution and care are factors, which
cannot be built into any product. These factors must be supplied by the persons caring for and using the unit.
The light source is non-user replaceable. The LED lamp panel must be replaced by a licensed electrician.

Plastic wire nuts (3)
Blade attachment screws and rubber washers (25)
1.5V AAA batteries (2)
3
Pre-Installation
TOOLS REQUIRED
Phillips
screwdriver
Flat blade
screwdriver
Step
ladder
Wire
stripper
Electrical
tape
Adjustable
wrench
HARDWARE INCLUDED
AB
C
NOTE: Hardware not shown to actual size.
A.
B.
C.
Electricians and Installers:
We are here to help you. Please call our support line if you have any questions or need assistance with installing or
wiring the product.
Customers and Purchasers:
Please call our Australian Support Team directly should you have any questions or concerns, or if you would like
advice on the best ways to use your fan to save energy.
ThreeSixty Support and Information Line:
1300 469 326

Mounting bracket (preassembled)
Canopy
Canopy dress ring (preassembled)
Hanger ball/downrod assembly
Coupling cover
Fan motor assembly
Blades (8)
Blade arms (8)
Light kit mounting plate
17W LED Light kit assembly
Glass shade
Receiver
Remote control
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
4
PACKAGE CONTENTS
Pre-Installation (continued)
b
1
4
5
6
9
7
11
10
8
2
3
12 13

5
Assembly
1Preparing the canopy
Assembling the fan
2
Remove the canopy dress ring from the canopy by
turning the dress ring counterclockwise.
Remove the mounting bracket from the canopy by
removing the non-slotted canopy mounting screw
from the bottom of the canopy and loosening the
slotted canopy mounting screw a half turn from the
screw head. Next, turn the canopy counterclockwise
to remove the mounting bracket from the canopy.
□Remove the hanger ball from the downrod
assembly by loosening the set screw, removing the
cross pin and lift the ball off the rod.
□Loosen the two set screws and remove the hitch pin
and retaining clip from the coupling on top of the
motor assembly.
□Carefully feed the electrical lead wires from the fan
up through the downrod. Thread the downrod into
the coupling until the Hitch pin holes are aligned.
□Next, replace the hitch pin and retaining clip.
Tighten both set screws.
WARNING: Failure to properly install the cotter pin
could result in the fan becoming loose and possibly
falling.
NOTE: If a longer downrod is needed (not included),
take out the screw located in the hanger ball, lower
the hanger ball and remove the pin. Remove all three
pieces from the downrod, and assemble them onto
the new longer downrod before proceeding step 3.
Downrod
Cross pin
Hanger
ball
Set screw
Supply Wires
Downrod
Hitch Pin
Retaining Clip
Set Screws
Set Screws
Canopy
Mounting
Bracket
Canopy
Dress
Ring
Screws

Assembly (continued)
Canopy
Motor
Coupling
Cover
Dress
Ring
Hitch Pin
Retaining Clip
Setscrews
Setscrew
□Slip the coupling cover, canopy cover and canopy
onto the downrod.
□Carefully reinstall the hanger ball onto the downrod,
being sure that the cross pin is seated in the
correct position, the setscrew is tightened and
wires are not twisted.
Downrod
Downrod Ball
Cross Pin Supply Wires
6

7
Assembly — Hanging the Fan
3
Hanger bracket installation
WARNING: The hanger bracket should be screwed
on to a firm flat surface. The fixing location must be
able to support 48kg.
Screw the hanger bracket to the ceiling and make
sure all connections are secure to prevent the fan
from falling.
Fixings must screw into a joist and not just the
plasterboard. Loosen the two canopy screws from
the hanger bracket.
WARNING: The tab in the ring must rest in the
groove of the hanger ball/downrod assembly. Failure
to properly seat the tab in the groove could cause
damage to the wiring.
Hanging the fan to the mounting
bracket
4
Carefully lift the fan motor assembly up to the
mounting bracket and seat the hanger ball/downrod
assembly in the mounting bracket socket. Make sure
the tab on the mounting bracket socket is properly
seated in the groove in the hanger ball/downrod
assembly. This will help to balance the ceiling fan
and prevent hanger ball rotation.
Ceiling
Screws
Mounting
Bracket
Lock Washers
Flat Washers
Ceiling
Mounting
Bracket
Hanger Ball
Fan Motor

Insert Receiver into Hanger Bracket with the flat side
of the Receiver facing the ceiling.
Connect the green/ground wires from the household
to the terminal block “ ” hole.
Connect the green/ground wires from the motor to the
terminal block “ ” hole.
Connect the hot household (red) wire to the terminal
block “L” hole.
Connect the neutral household (black) wire to the
terminal block “N” hole.
Connect the green/ground wire from the receiver to
the terminal block “ ” hole.
Connect the brown wire from the receiver to the
terminal block “L” hole.
Connect the blue wire from the receiver to the terminal
block “N” hole.
Be sure to connect the 2-pin and 3-pin male plugs
(from fan) to the receiver.
Ensure you install a means of electrical disconnection
(double pole isolation switch) of both poles into your
fixed wiring in accordance with the electrical wiring
rules.
8
Assembly — Hanging the Fan
5Making the electrical connections
WARNING: To avoid possible electrical shock, be
sure you have turned off the power at the main circuit
panel. Follow the steps below to connect the fan to
your household wiring.
NOTE: This unit is equipped with an automatically
learned type remote control. There are no frequency
switches on the receiver and transmitter; the receiver
unit will automatically scan the frequency from the
handheld remote if any changes are made. Should you
desire to install another fan within the same home or
area with a seperate frequency code please see the
"Learn Mode Process" operating the remote control
section of this instruction manual to learn how to
change the frequency.
Mounting
Bracket
Receiver
Fan Motor
RECEIVER
Green/Ground
(Hanger bracket)
Green/Ground
(motor)
3-Pin male plug
2-Pin
male plug
Black
(household “N”)
Terminal block
Blue (AC IN N)
Green/Ground ( )
Brown (AC IN L)
Red
(household “L”)
Green/
Ground
(household “ ”)

9
Assembly — Hanging the Fan (continued)
6Installing the canopy
WARNING: Make sure the tab on the mounting bracket
properly sits in the groove in the hanger ball before
attaching the canopy to the mounting bracket by turning
the downrod hanger ball until it drops into place.
Make sure connections are neatly tucked into the
ceiling canopy. Electrical tape to hold excess wiring
is useful.
Slide the canopy up to the mounting bracket and
place the key hole on the canopy over the loose
canopy mounting screw on the mounting bracket.
Turn the canopy clockwise until it locks in place at
the narrow section of the key holes.
Align the circular hole on the canopy with the
remaining hole on the mounting bracket, secure
the canopy mounting screws previously removed in
the hole, and tighten the two canopy mounting
screws.
Attach the canopy dress ring to the canopy
mounting screw heads by inserting the screw
heads into the key slots in the dress ring and
rotating it clockwise.
Canopy
Canopy
Dress Ring
Screws
Screws
Dress Ring
Screws
Mounting
Bracket

10
Assembly — Attaching the Fan Blades
7Attaching the Fan blades
Screws and
Fiber Washers
Blade Arms
Blade Arms
Fan Motor
Blades
Blades
WARNING: To reduce the risk of personal injury, do
not bend the blade arms while installing, balancing
the blades , or cleaning the fan. Do not insert foreign
objects between rotating fan blades.
NOTE: Your fan blades (H) are reversible. Select the
blade (H) side finish which best accentuates your decor.
□The fan motor assembly is shipped with rubber
packing mounts to prevent movement during
transportation. Remove the six rubber packing mounts
from the fan motor assembly and discard prior to
attaching the blade arms.
□Attach the blades to the blade arms using the three
blade attachment screws and fiber washers. Start a
screw with fiber washer into the blade arms, but do
not tighten.
□Repeat for the two remaining blade attachment
screws and fiber washers.
□Tighten each screw securely starting with the center
screw. Make sure the blade is straight.
□Repeat these steps for the remaining blades.
□Fasten the blade assemblies to the fan motor
assembly.
□Tighten the two blade arm screws and lock washers
already installed in the blade arms.
□Repeat this procedure for the remaining blade arms.

11
8
Assembly — Installing the Light Kit
□Remove one of the three light kit mounting plate
screws from the mounting ring and loosen the other
two screws. (Do not remove.)
□Place the key holes in the light kit mounting plate
over the two screws previously loosened from the
mounting ring. Turn the light kit mounting plate until
the light kit mounting plate locks in place at the
narrow section of the key holes.
□Replace the removed mounting plate screw and
tighten. Now securely tighten the other two screws
previously loosened.
□Remove one of the three light kit mounting screws
from the light kit mounting plate and loosen the other
two screws. (Do not remove.)
□While holding the 17W LED light kit under the fan
motor assembly, make the 2-pin wire connections:
- White to white
- Black to black
□Place the key holes in the LED light kit over the two
mounting screws previously loosened from the light
kit mounting plate. Turn the LED light kit until the
LED light kit locks in place at the narrow section of
the key holes. Secure by tightening the two light kit
mounting screws previously loosened and the one
previously removed.
□Position the notches in the outer rim of the glass
shade so they line up with the tabs on the inside of
the rim on the LED light kit. Carefully lift the glass
shade up inside the LED light kit and secure it to the
fan by turning the glass shade clockwise until snug.
DO NOT OVERTIGHTEN.
Attaching the LED light kit
CAUTION: Before starting installation, disconnect the
power by turning off the circuit breaker or removing
the fuse at the fuse box. Turning power off using the
fan switch is not sufficient to prevent electric shock. Fan Motor
Screws
Light Kit
Mounting
Plate
Mounting
Ring
Fan Motor
Screws
LED Light Kit
Light Kit
Mounting
Plate
Notches
Tabs
Glass shade

D. Button:
This button is used to turn on the light kit and also
controls the brightness setting. Press and release this
button to turn the light on. Press and hold ” ” button
to set the desired brighten. Press and hold ” ” button
to set the desired darken. The light button has an
auto-resume, it will stay at the same brightness as the
last time it was turned off.
E. Button:
This button is used to turn on the light kit off.
F. Button:
Forward/Reverse (see next page)
12
Operation
OPERATING THE REMOTE CONTROL
– non-rechargeable batteries are not to be recharged
– exhausted batteries are to be removed from the appliance
and safely disposed of.
– if the appliance is to be stored unused for a long period,
the batteries are removed.
– the supply terminals are not to be short-circuited.
Screw
Battery
cover
Remove the set screw on the back of transmitter, take out
the battery cover. Insert two 1.5 volt AAA batteries (included).
LEARN MODE PROCESS
Step 1. Control and receiver have been factory programmed.
If replacing the transmitter or receiver, the learn mode
process will need to be used.
Step 2. After installing the unit and restoring power to your
fan, press and hold the ” ” button 3~5seconds. Light will
flash twice and the motor spin, which indicates that the
learning process has completed.
IMPORTANT: You must press the “ ” button within 60
seconds of restoring power to the fan. Remote does not
need to be re-learned when replacing the battery.
Step 3. Please note, the remote can learn multiple receivers.
Please make sure not to learn with other receiver during the
learning process.
Step 4. Re-install the battery cover.
WARNING:
To prevent damage to transmitter, remove the battery if not
used for long periods.
A. 1, 2, 3, 4, 5, 6 Buttons:
These buttons are used to set the fan speeds as follows:
1 : Minimum Speed
2 : Low Speed
3 : Medium Low Speed
B. Button:
This button turns the fan off. When fan is turned off, a
momentary increase in speed can occur before the fan
slows and then finally stops.
C. Timer
Pressing the timer buttons will automatically turn fan and
light (if light is on) off after 2, 4, or 8 hours.
4 : Medium Speed
5 : Medium High Speed
6 : High Speed
Off 2H4H
8H Disables timer

13
Operation (continued)
Care Of Your Fan
REVERSE BUTTON OPERATING
INSTRUCTIONS
This control system is designed to "Reverse" the rotation
of the blades.
Warm weather - Forward (counter clockwise) A downward
airflow creates a cooling effect as shown. This allows you
to set your air conditioner on a warmer setting without
affecting your comfort.
Cool weather - Reverse (clockwise) An upward airflow
moves warm air off the ceiling area as shown. This allows
you to set your heating unit on a cooler setting without
affecting your comfort.
Here are some suggestions to help you maintain your fan:
1. Because of the fan's natural movement, some connections may become loose. Check the support connections,
brackets, and blade attachments twice a year. Make sure they are secure. (It is not necessary to remove fan from
ceiling.)
2. Clean your fan periodically to help maintain its new appearance over the years. Use only a soft brush or lint-free cloth
to avoid scratching the finish. The plating is sealed with a lacquer to minimize discoloration or tarnishing. Do not use
water when cleaning. This could damage the motor, or the wood, or possibly cause an electrical shock.
3. You can apply a light coat of furniture polish to the wood blades for additional protection and enhanced beauty. Cover
small scratches with a light application of shoe polish.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.
IMPORTANT
MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU ATTEMPT ANY REPAIRS.
REFER TO THE SECTION "MAKING ELECTRICAL CONNECTIONS".

14
Problem Solution
1. Check circuit fuses or breakers.
2. Check all electrical connections to insure proper contact.
CAUTION: Make sure the main power is OFF when checking any electrical connection.
3. Check that the battery of the remote is functional.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade brackets to the motor are tight.
3. Make sure wire nut connections are not rubbing against each other or the interior wall of the
switch housing. CAUTION: Make sure main power is off.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during
this time.
5. Make sure the upper canopy is a short distance from the ceiling. It should not touch the
ceiling.
6. Do not connect the fan with a wall mounted variable speed control(s). They are not
compatible with DC motors.
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. Measure this distance
(from floor or ceiling). Rotate the fan until the next blade is positioned for measurement.
Repeat for each blade. The distance deviation should be equal within 1/8" (3mm).
3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1. Replace the batteries in the remote control handpiece.
Fan will not start.
Fan sounds noisy.
Fan wobble.
Remote control
malfunction.
Troubleshooting

15
1. Download the Bond Home App, available on the Google Play Store
and Apple App Store, or use the QR code to download the app.
2. Open the Bond Home App.
3. If you already have a Bond account, simply log in and continue to
Step 4. If you do not have a Bond account, press "Create Account"
and enter your name, email and a password.
4. Select "+" to add a device.
5. Select "Smart By Bond" (SBB).
6. Select this smart ceiling fan.
7. Once the Bond application connects to the fan, select "CONTINUE" to
proceed.
8. Test the fan functions to ensure commands work as expected.
9. Select "YES, IT WORKS".
10. Specific information about your fan:
a. Select "Location" and choose from one of the predefined
entries or add your own by selecting "OTHER". When finished,
select "Save".
b. Select device name and enter the name for your device. When
finished, select "OK" to save.
PLEASE NOTE: This name will be used for integrations, so a
simple, easy-to-remember name is best.
11. Select "Continue".
12. Select the Wi-Fi network you would like to connect the SBB to.
13. Enter the Wi-Fi password and select "OK".
14. If there is an issue with the connection or wrong password is entered,
you will receive an error message. Select "OK, I've Got It".
15. Once the connection is made, select "DONE".
16. If the SBB fan is not displayed in the Bond application, swipe down to
refresh.
Smart Ceiling Fan Wi-Fi Control (optional)
Without Wi-Fi activation, you will not enjoy the expanded features and functionality of your ceiling fan: Breeze speed
settings, creating schedules and Voice Activation.
To enjoy all the potential of your new device, refer to the following steps to complete the Smart Setup.
For assistance at any time during this process, or when using your Bond Home App, go to the "Help" section:
1. Tap on "Settings".
2. Tap on "Help Center".
3. Choose "Open a Ticket" or "Live Chat".