Thuli Tables 500 Stationary User manual

500 Stationary Owner’s Manual
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 2
Identication of Parts . . . . . . . . . . . . . . . 3 - 4
Table Assembly . . . . . . . . . . . . . . . . . . . . . . 5
Headpiece Operation . . . . . . . . . . . . . . . . 6 - 8
Table Operation . . . . . . . . . . . . . . . . . . . 9 - 12
Accessories . . . . . . . . . . . . . . . . . . . . . . . . 13
Care & Maintenance . . . . . . . . . . . . . . . 14-15
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Overview of Products . . . . . . . . . . . . . . Back
Crescent Arm Rest
(optional)
THULI TABLES
[email protected]
www.thulitables.com
youtube.com/thulitables
800-458-4854
facebook.com/thulitables

2
Introduction
Rick Thuli, D.C.
President
Sincerely,
We are pleased to provide you with an aesthically beautiful chiropractic
adjusting table that is versatile and precisely engineered. It has been
thoroughly inspected and tested right down to the smallest detail before
leaving our shop. We are condent that it will provide you with many
years of reliable service.
Please take the time to read this manual carefully. It will familiarize you
with the table and instruct you on its proper operation and maintenance.
If you have any questions or comments, please contact us.
Thank you for your purchase of a 500 Stationary table.

Crescent Arm Rest
Ankle Rest
Extension / Elevation
Pelvic Section
Fixed Section
Thoracic Section
Headpiece
Foot Cocking Pedal
Ankle Rest
Extension
Locking Knob
Pelvic Tension
Control Knob Thoracic Tension
Control Knob
Pelvic
Lowering
Lever
Thoracic
Lowering
Lever
14
Identification of Parts 3
(optional)

Tension Control Knob
(back side)
Paper Hold-Down Wire
Pivot Block
Slide Block
Paper Hanger
Remote Control Lever
Paper Tear-Off Bar
Straight Drop /Forward
Motion Knob
Cocking Lever
Remote Control Cable
Piston Pin
T-Bar
Adjustable Buckle for
Prone Arm Rest
Flexion /Extension
Piston
Crescent Arm Rest
Locking Link
Lateral Flexion Lever
14
Identification of Headpiece Parts 4

ANKLE REST ATTACHMENT
Your table is easy to set up and operate. In order to protect the headpiece and ankle rest extension during shipment, they have been
packaged together in a separate box from the table. A wrench is provided for table assembly, and the accompanying set up instructions
will assist you.
1. Remove the hitch pins and “O” rings from the ankle rest
extension rods.
2. Remove tape from the ankle rest extension lockout knobs.
3. Slowly insert the ankle rest extension assembly through the
frame, plastic housings and wood crosspiece.
4. Once you’ve pushed the ankle rest extension all of the way
in, replace the “O” rings and hitch pins.
HEADPIECE ATTACHMENT
Attach the headpiece to the four protruding bolts at the front of
the table, using the wrench provided.
14
Table Assembly 5

1. Install a standard 8.5” roll of headpiece
paper, as shown.
2. Raise the paper hold-down wire and
tear-off bar. Advance the paper and
tuck it between the cushions.
3. Lower the hold-down wire between the
cushions, lower the tear-off bar and
tear off excess paper.
HEADPIECE PAPER
4. To advance the headpiece paper, raise
the tear-off bar, hold your nger on the
paper hold-down wire and pull the paper
across the cushions. Pulling the paper
in an upward direction will reduce friction,
making it easier to pull.
5. To tear off used headpiece paper, use
an upward motion while holding down
the tear-off bar.
FLEXION / EXTENSION
Flex and extend the headpiece by
grasping the front end of the headpiece
and operating the remote control lever.
LATERAL FLEXION
To ex the headpiece laterally, lift the
lateral exion lever in a counterclockwise
direction, manually position the headpiece,
then lock it into position by tightening
the lateral exion lever. This can be done
while the headpiece is in the exed,
extended or elevated position.
LATERAL FLEXION LEVER
The position of the lateral exion lever can
be changed. With the lateral exion lever
tightened, pull the lever directly outward,
rotate to the desired position, and release.
14
Headpiece Operation 6

STRAIGHT DROP FORWARD MOTION DROP
VERTICAL ELEVATION
1. Raise the back end of the headpiece by
lifting the red grip of the cocking lever
(without operating the lever).
Caution: Do not grasp the cushions to
raise the back end, which could stretch
and damage the small springs.
2. Raise the front end of the headpiece
by operating the black exion/extension
control lever, as in headpiece exion/
extension.
3. With practice, steps 1 and 2 can be
combined to vertically raise the head
piece in one smooth motion.
14
Headpiece Operation 7
13
Knob pushed in PRIOR to cocking
Knob pulled out PRIOR to cocking
PRIOR to cocking the headpiece, set for
straight drop by pulling out the headpiece
straight drop/forward motion knob until
you feel it is “set” into position. This will
be just short of coming into contact with
the cocking bar. If you pull the knob out
too far, simply push it back in and continue.
PRIOR to cocking the headpiece, set for
forward motion drop by pushing in the head-
piece straight drop/forward motion knob.
Cock the headpiece with an upward motion on the headpiece cocking lever.
Please note: Be sure to change the head-
piece drop function before cocking the
headpiece to prevent an ineffective drop and
damage to the drop mechanism.
Set the desired tension by turning the tension control knob clockwise (increasing tension) or counterclockwise (decreasing tension).

VERTICAL LOWERING
1. Lower the front end of the headpiece
by operating the remote control lever.
2. In one smooth motion, lower the
back end of the headpiece by lift-
ing the headpiece lowering lever
rmly with one hand while gently
lowering the back end of the head
piece with the other.
IMPORTANT
ANKLE REST EXTENSION
The ankle rest can be extended up to 10”
to accommodate taller patients. Shorter
patients can drop their feet into the recess
created by the extended ankle rest.
Locking knobs are provided on both sides
of the table.
ANKLE REST ELEVATION
To ELEVATE, simply lift up on the
ankle rest.
To LOWER, lift the center of the
wood bar with one hand while gently
lowering the ankle rest with the other
hand.
14
Headpiece & Ankle Rest Operation 8
ANKLE REST LOWERING
Advise your patient before changing the
position of the headpiece. This is especially
important when lowering the back end of
the headpiece (step 2). Failure to gently
lower the back end of the headpiece may
result in its sudden drop, causing possible
alarm to the patient.

PRONE POSITION
Side posture positioning of the patient’s
head for lumbo-pelvic adjusting or
toggle recoil adjusting.
SIDE POSTURE POSITION SUPINE POSITION
The headpiece can be positioned to support the
cervical spine and head when the patient is
in the supine position.
We recommend that the patient be
positioned sufciently forward with their
arms outstretched and wrists resting on
the prone arm rest. By using the strap,
the prone arm rests can be adjusted to the
patient’s comfort.
14
Table Operation 9
EYE COMFORT IN PRONE POSITION
For patients who are sensitive to pressure on their eyes, slightly raise the back end of the
headpiece. This will take pressure off of the eyes by supporting the weight of the head
at the mandible and zygomatic arches. Using this maneuver, in combination with slight
exing of the headpiece, will provide additional comfort for many patients.
HEADPIECE CUSHIONS: ADJUSTABLE WIDTH
Neutral position. Narrower position for smaller faces
(eg children).
Wider position takes pressure off of
the patient's eyes.
The headpiece cushions are easily adjustable in width for individualized patient comfort. Firmly pull up on the front end of each
headpiece cushion and move in (one or two notches) or out (one or two notches) to desired position. Secure cushions by engaging
locating pins into notches provided.

THORACIC DROP
Proper prone positioning on the pelvic drop section should
have the patient’s anterior superior iliac spine (ASIS) at the
juncture of the pelvic and thoracic sections.
When using the thoracic drop, position the patient sufciently
forward with their arms outstretched and wrists resting on
the prone arm rest.
14
Table Operation 10
PELVIC DROP
SETTING THE DROP TENSION
1. With the patient on the table, cock the drop section. You
must have sufcient tension on the drop mechanism to
hold the patient’s weight.
2. Loosen the tension by turning the tension control knob counter-
clockwise until the section drops.
3. Tighten the tension by turning the tension control knob
clockwise 3-4 half turns.
The thoracic and pelvic drops cock by stepping down on the
foot cocking pedals. Advise your patient of your intentions
before setting the tension.
As a general rule, the drop section is now set for the patient’s
weight, which may vary according to the practitioner’s
preference.

TO RAISE, simply lift up on the cephalad end. Ask the patient to
assist you by momentarily sitting up and forward while you raise
the thoracic section to the desired height/angle. TO LOWER:
1. Ask your patient to sit forward on the table removing
weight from the thoracic section.
2. Pull back and upward on the thoracic lowering lever.
3. Lower the thoracic section by pushing down on the
cephalad end.
THORACIC SECTION: RAISING
The cephalad end of the thoracic section can be raised to a height
of 0”- 9.5” from horizontal, which translates to an angle of 0 - 30
degrees, and is designed to be used with the patient in the supine
position only.
14
Table Operation 11
IMPORTANT: Before lowering the thoracic from a raised
position, advise your patient of your intention. Do not attempt
to lower the thoracic section with the patient’s weight on the
section or without the patient’s knowledge, as this could result
in a sudden drop of the secton causing suprise and/or possible
injury to the patient.
THORACIC SECTION: LOWERING
USES INCLUDE: Anterior Thoracic, Cervical Palpation
and Diversied Cervical adjusting (while the practitioner
is in a comfortable, upright position).

MULTIPLE SECTION POSITIONING
12
Pregnant woman
in prone position
By changing the position of each section, the
table can comfortably accommodate various
body types.
TO RAISE, simply lift up one cephalad end. If your patient is
lying prone on the table when you intend to raise the section,
ask the patient to assist you by momentarily shifting his/her
weight off of the pelvic section (e.g. to his/her chest and knees)
while you raise the pelvic section to the desired height/angle.
TO LOWER:
1. Ask your patient to shift his/her weight off of the pelvic section,
2. Pull back and upward on the pelvic lowering lever.
3. Lower the pelvic section by pushing down on the cephalad end.
The cephalad end of the pelvic section can be raised to a
height of 0”-6 1/2” from horizontal, which translates to an
included angle of 0-22 degrees and is intended to be used with
the patient in the prone position only.
Before lowering the pelvic section from a raised position, advise
your patient of your intention. Do not attempt to lower the pelvic
section with the patient’s weight on the section or without the
patient’s knowledge, as this could result in a sudden drop of the
section causing undue alarm and/or possible injury to the patient.
PELVIC SECTION: LOWERING
Table Operation
PELVIC SECTION: RAISING

14
CRESCENT ARM REST
The Crescent Arm Rest provides additional forearm support in the
prone position. Can be retrotted to your table at anytime
(minimal installation required).
COMFORT PILLOW
Accessories
The base of the Comfort Pillow inserts into place
between the headpiece cushions. The opening is
adjustable.
13
Comfort Pillow
Crescent Arm Rest
Rotate the Comfort Pillow 180
degrees to provide cervical
support in the supine position.
Base
Pillow
The Comfort Pillow offers
massage quality comfort in the
prone position.
The Velcro on the
underside of the pillow
secures it to the base,
allowing for width
adjustability.
Bolsters are 20" wide with a nonslip base. Choice of two
heights: 2.75" or 4.25". Use in prone position under ankles or in
supine position under knees to relax hamstrings.
BOLSTERS
2.75" x 20" Bolster (shown on Tour portable table)
PRONE ARM REST SHIELDS
Nonporous and durable plastic
shields slip over the prone arm rest
grips. Easy to sanitize.

Care & Maintenance 14
CERVICAL DROP
Thoracic Drop Pelvic Drop
1. Elevate and cock the thoracic and pelvic drop sections.
Locate the lubrication hole on the top of each drop.
THORACIC & PELVIC DROPS
2. Lubricate with 3-IN-ONE oil: Using the syringe, apply
oil into the hole. Note that the hole is not directly over the
plunger, so position the syringe at an angle to direct the oil
onto the plunger. Allow a few minutes for the oil to
penetrate before using. Lubricate every month or
500 adjustments.
DROP MECHANISMS: CLEANING & LUBRICATION
2. Lubricate with 3-IN-ONE oil: Apply oil into the hole. Allow a few minutes
for the oil to penetrate before using. Lubricate every month or 500 adjustments.
1. Raise the back of the headpiece and locate the hole in the plastic block2
3-IN-ONE OIL
Use 3-IN-ONE oil for routine lubrication of the drops.
To access the thoracic and pelvic plungers, use a small syringe (one provided).
Squeeze several drops of 3-IN-ONE oil onto a non-porous surface and suction into the
syringe. Save the syringe for future use.
Periodic lubrication of the drop mechanisms will ensure smooth, crisp drops. Apply 3-IN-ONE oil every month or 500 adjustments.
If the drops have not been lubricated on a regular basis, rst apply WD-40 to clean the plungers from dust & debris. See below.
3. Clean with WD-40: If the drop has not been lubricated on a regular basis, apply
WD-40 into the hole and drop the headpiece several times to clean off dust & debris.
It is important to follow the cleaning with 3-IN-ONE oil for lubrication.
3. Clean with WD-40: If the drops have not been lubricated
on a regular basis, apply WD-40 into the hole. Drop the
section several times to clean the plunger of dust & debris.
It is important to follow with 3-IN-ONE oil for lubrication.

Care & Maintenance 15
THORACIC & PELVIC STRIKE PLATES: PERIODIC TIGHTENING
Periodic tightening of the thoracic and pelvic drop mechanism strike plates
will assure proper functioning and reduce wear on the cocking arms.
It is recommended to do this about once/month.
First, cock the drop. Using the long-handled 3/16” allen wrench provided
with your table, insert it between the two springs of the drop mechanism
and rmly tighten the screw in the strike plate. Do this on both of the
thoracic and pelvic strike plates.
Photo shows tightening the thoracic strike plate.
CERVICAL DROP
2. Lubricate with 3-IN-ONE oil: Apply oil into the hole. Allow a few minutes
for the oil to penetrate before using. Lubricate every month or 500 adjustments.
1. Raise the back of the headpiece and locate the hole in the plastic block2
VINYL CLEANING
1. Mild Daily Cleaning: Use dish soap and warm water (1:10) with a soft cloth. Follow with a thorough, clear water rinse.
If more cleaning is necessary, use a soft bristle brush with the same solution. Avoid harsh detergents and powdered abrasives.
Areas coming in contact with hair, body oils or perspiration should be washed frequently. Remove stains immediately to prevent
the possibility of becoming permanent.
2. Disinfecting Options:
Bleach: Dilute 4 tsp bleach in 1 quart of water in a spray bottle. Spray on vinyl, leave for 1-2 minutes and rinse well with water.
Hydrogen Peroxide (3%): Available in spray bottle. Use undiluted and leave on for 5 minutes and rinse well with water.
Alcohol (70% min): Use undiluted. Leave on for 1-2 minutes and rinse well with water.
REPLACEMENT VINYL: In the event of wear or damage, pre-sewn replacement vinyl is available from Thuli Tables.
3. Water Rinse: It is important to follow cleaning with a thorough, clear water rinse to minimize premature deterioration of the
vinyl extended exposure to chemicals.

13
Warranty 16
If your table needs repair, whether under warranty or not, please contact us. We will determine what is needed and, at our
discretion, send you either a replacement or the necessary part for repairing. Our tables have been designed so that replacing a part
is relatively easy to do yourself. Please note that we do not cover labor costs if you hire someone to install the replacement part
on your behalf.
Our tables are designed and built to high standards and we are proud to offer a limited lifetime warranty against manufacturing
defects. This warranty is valid to the original owner and only if the table has not been altered in any way. It does not cover issues
caused by normal wear and tear, which naturally and inevitably occur as a result of normal use over time, or damage caused by
accidents, improper use and negligence. It also not does not cover the headpiece exion/extension piston and the electric motor
(on elevating tables). These two items are covered by a one year warranty against manufacturing defects.

13

Elevation Tables
Tour Portable
300 Stationary
Sport Portable
500 Stationary
Portable Drops
Lumbo-Pelvic Drop
Extremity Drop
Speeder Board
Portable
Headpiece
Junior Portable
www.thulitables.com
[email protected]
608.935.9300
800.458.4854
youtube.com/thulitables
facebook.com/thulitables