DT Research DT390i Assembly instructions

DT390i
ENGLISH
Mobile POS Tablet
BASIC OPERATION GUIDE
DT390i
ENGLISH 8
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131 hp://www.dtresearch.com
Copyright © 2012, DT Research, Inc. All Rights Reserved.
DT Research is a registered trademark of DT Research, Inc.
INTRODUCTION
Thank you for acquiring the latest addion to DT
Research’s line of mobile tablets—the DT390i. Featuring
an IP64-rated, slim yet robust enclosure, the two-pound
DT390i with 8.9”TFT display is powered by the Intel®Atom™ processor, offering opmal
combinaons of performance and power savings. An external baery expansion opon
provides approximately 3-4 hours of addional baery operaon for up to eight hours
of mobile usage.
The DT390i is available with Windows®Embedded Standard 7, Windows®XP Embedded,
Windows®XP Pro for Embedded Systems, Windows®7 Pro or Linux operang systems.
Each soware operang system features web browser, client/server compung
soware, media player, accessories, and applicaons support.
PACKAGE CONTENTS
DT390i with Internal Baery Pack, Stylus and Bumpers•
AC-DC Power Adapter with Power Cord•
Basic Operaon Guide•
Handstrap•
Major opons, depending on configuraon:
Desktop Charging Cradle with DC-in Power Jack and Ethernet/ USB Ports•
X-handstrap•
External External Baery Pack and Baery Charger Kit•
Vehicle/ Wall Mount Cradle•
* If your DT390i contains MSR, half-slot smart card reader, RFID reader, camera, 3G or scanner
module, please refer to the POS module operaon guide for detailed operaon.
BOG111312DT390iENG
SPECIFICATIONS
System
Processor Intel® Atom™ Z530, 1.6GHz
Memory (RAM) 2GB DDR2 533MHZ
Storage 8GB to 64GB Flash
Operang Systems
Microso® Windows® Embedded Standard 7, Windows® 7
Professional, Windows® XP Embedded; Windows® XP Pro
for Embedded Systems, or Linux
Display 8.9”LED-backlight screen with resisve touch; sunlight-
readable LCD opon
Display Resoluon 1024 x 600 (WSVGA)
Network Interface Wi-Fi 802.11a/b/g/n, Bluetooth 2.1 with EDR
Trusted Plaorm Module TPM 1.2 support
Control Switch and Buons 1 power buon, 7 front buons and 1 trigger buon
Indicator 1 power/ baery status LED and 1 WLAN acve LED
Speaker/Microphone Built-in speaker; built-in internal microphone
Input/Output Ports 1 DC-in Jack; 1 USB 2.0 ports; 1 Headphone-out Jack
combined with microphone, 1 Full Slot Smart Card Reader
Full Slot Smart Card Reader Reads ISO 7816 T=0, T=1; EMV 2000 cerfied, 1.8/3/5V
smart card
Power
AC/DC Adapter Input: 100 – 240V AC; Output: 19V DC, 2.36A
Baery Pack Internal 7.4V, 3760mAh/
Oponal: External 7.4V, 3760mAh/ 7.2V, 3900mAh
Mechanical
Enclosure ABS + PC plascs
Stylus Non-electronic p
Protecve Bumpers Rubber bumpers on each corner for handling protecon
Dimensions (H x W x D) 7.7 x 10 x 1.25 in/ 196 x 256 x 32 mm
Weight 2.43 lbs/ 1.1 kg
Environmental
Water and Dust Resistance IP64 * IP64 rang may not be applicable for units with module
opons
Vibraon and Shock Resistance MIL-STD-810G
Regulatory FCC Class B, CE, C-Tick, RoHS compliant
Temperature
Operaon: -20°C - 50°C
(The DT390i must be charged unl the power LED indicator blinks
blue, then the 390i can be used in low temperatures);
Storage: -20°C - 60°C
Humidity 0% - 90% non-condensing
* Specificaons subject to change without noce.

DT390i
ENGLISH 23ENGLISH
Buon Funcons (with Windows XP Operang System)
BUTTON ACTION
Programmable
Programmable, launch so(on-screen) keyboard (default)
Launch SAS (Secure Aenon Sequence)
Generate Ctrl+Alt+Del keys to invoke the security windows defined under Windows XP
Programmable,
Calibrate touch screen before log on the operang system
Change display orientaon (portrait/ landscape) (default)
Programmable, system ulity menu (default)
Programmable,
As scanner trigger when equipped with the scanner module
Power on,
Push/release typically enters Standby mode, or Push/release exits Standby mode or
restarts device (soware dependent)
Push and hold (over 4 seconds) invokes hardware shutdown
The DT390i (with Windows XP Operang System)
Baery/Power LED
Wireless LEDMicrophone
Stylus
Buon ManagementWireless Network Sengs
Calibraon
Power/Baery LED Status:
Blue indicates the baery is 25% to 100% charged•
Blinking blue indicates the baery is charging•
Orange indicates that the baery is between 11% to 25%•
Blinking orange indicates that the baery is below 10%•
Blinking blue and orange alternately indicates the baery is being warmed up. Do not•
unplug the AC/DC adapter.
Precauons
Always exercise care when operang and handling the DT390i.
•
Do NOT apply excessive pressure to the display screen.
•
We recommend using the Stylus provided to keep the screen clean.
•
Avoid prolonged exposure of the display panel to any strong heat source. Wherever
•
possible, the DT390i should face away from direct light to reduce glare.
If the AC-DC power adapter is used to recharge or power the device, do NOT use any
•
AC-DC adapter other than the one provided with the device or acquired from the
manufacturer or its partners.
In the unlikely event that smoke, abnormal noise, or strange odor is present,
•
immediately power offthe DT390i and disconnect all power sources. Report the
problem to your device provider immediately.
Never aempt to disassemble the DT390i, as this will void the warranty.
•
The DT390i internal baery is designed for wide temperature usage. Please do not use
•
it for other tablet models.
(The wide temperature design is not applicable for external baery)
Basic Features
The DT390i wireless tablet integrates a bright and responsive touch display, 1 USB port,
and embedded networking elements such as wireless LAN or oponal 3G. The primary
device is complemented by a suite of accessories, including baery expansion, docking
cradles, and wall/ vehicle mount cradles, for a comprehensive user experience.
A DT390i typically integrates an 802.11a/b/g/n wireless LAN (WLAN) adapter that may
connect to other wireless devices or access points. If your DT390i does not come with
such a network adapter, please consult your device provider to establish the desired
network connecvity.
1
8
9
2 3
4
5
6
8
9
7
Input/ Output Ports
Headphone Jack
USB Port
DC Power Input
Full Slot Smart Card Reader
A
C
D
B
A
B
C
D
1234567
Baery and Power Meter

DT390i
ENGLISH 45ENGLISH
OPERATION
Internal Baery
Warning!
The Internal baery pack should only be replaced by an authorized DT Research service
representave. Please contact your product and/or service provider for internal baery
replacement service.
Powering ON and OFF
To acvate the DT390i, push and quickly release the Power Buon. The display will come
on in a few seconds. To put the DT390i in Standby mode, push and quickly release the
Power Buon. To turn the DT390i offfor extended storage, power offthe device safely
using any soware funcon that “shuts down computer”provided in the soware
operang system.
NOTE: The baery packs shipped with your device may be low in power—please use
the AC-DC adapter with the DT390i when seng up the device for the first me to
fully charge the internal baery pack. You may charge the external baery pack with it
aached to the DT390i, or with the oponal external baery charger kit.
NOTE: When the baery pack(s) is (are) charging, the blue-colored Baery LED should
blink slowly. If plugging in the AC-DC adapter does not trigger this blinking acvity
and the LED stays dark, the baery pack(s) may have been drained substanally. Try
unplugging/ replugging the AC-DC adapter to the DT390i a few mes to acvate the
charging process.
NOTE: To conserve power, use (push and quick release) the Power Buon to put the
device in “Standby”mode while not in use. Pushing briefly on the same buon will wake
up the system within seconds.
NOTE: Avoid using the Power Buon (“hold 4+ seconds”feature) to turn offthe
device—this form of hardware shutdown is intended to be a means of recovery from
device lockups, and not as normal operaon.
Start Up
If the power up (from Standby or otherwise) is successful, the appropriate interface will
be displayed aer a launch sequence of several seconds. The wireless LAN connecon
may take 10-15 seconds to be established.
Configuring the DT390i
The device may be configured using the ulies and methods dictated by the soware
operang system. The DT390i should be configurable for various properes such as user
profiles, network features, and several system elements.
Calibraon
The touch display for the DT390i is calibrated before shipping. In the event that the
calibraon has been modified or is unsasfactory, the respecve calibraon rounes
(e.g., PenMount (PM) for Windows XP) to calibrate the touch interface may be used.
Such applicaons are typically executed through touch input via Stylus or through mouse
click via a USB mouse.
Wireless Networking
Wireless LAN
The DT390i is oen delivered with an embedded (user-inaccessible) 802.11a/b/g/n
WLAN adapter equipped with a hidden custom antenna.
T
•hrough the support of typical WLAN adapters, the DT390i should be able to detect
all 802.11 access points in the vicinity for you to select the access point of your
choice for connecon.
T
•he SSID and WEP/WPA/WPA2 (if enabled) parameters on the DT390i and the
access points have to match. The SSID is case-sensive and it is recommended
that you enable WEP/WPA/WPA2 encrypon (or advanced alternaves) for secure
access.
W
•hen WEP/WPA/WPA2 is enabled, you may need to consult your network admin-
istrator or your networking equipment literature to properly configure associated
sengs such as Authencaon mode, etc.
R
•efer to the access point operang manuals for seng up the 802.11 access points.
!

DT390i
ENGLISH 67ENGLISH
Buon Management
Where supported by soware, many of the hard buons on the DT390i are
programmable to perform a funcon of the user’s choice. The excepon is the Power
Buon and the SAS Buon. To acvate the buon re-assignment applicaon, invoke the
Buon Manager applicaon, e.g., in Windows XP Embedded .
Brightness Control
Where supported by device firmware and soware, a hard buon may be engaged to
manipulate the display brightness. Press the System Ulity Menu buon (Buon 7) on
the front of the DT390i. The System screen will display a Brightness control secon with
up and down arrows that can be acvated with the stylus.
Baery and Power Management
The DT390i is equipped with an internal 3760mAh Li-Ion baery pack that is capable of
supporng approximately 3 - 4 hours of connuous operaon. With the internal baery
and an external baery pack that clips (hot-pluggable) onto the back of the device,
the maximum period of connuous operaon will be approximately 6 - 8 hours. The
period between baery recharges can be significantly lengthened by pung the device
into Standby mode through the Power Buon (see Buons Funcon Table) whenever
the device is not in use. Depending on the operang soware, the DT390i may also be
configured to enter various power-saving modes via the Power Buon or through med
entry.
Full Slot Smart Card Reader
The DT390i comes with a full slot smart card reader.
Remove the rubber and insert a card (Picture 1).•
Use the stylus to pull the metal pull and then remove the card (Picture 2).•
USING THE DT390i
Memory & Storage Configuraon
The DT390i is available with 2GB memory configuraon. Storage opons currently range
from 2GB to 32GB flash memory.
Peripherals Support
Through its USB port, the DT390i supports a wide range of USB-based peripherals. These
peripherals are applicable for soware installaon, applicaons storage, data storage,
docking or soware recovery and update.
The DT390i is complemented by an oponal Desktop Cradle or Wall/ Vehicle Mount
Cradle for support, pass-through charging, and connecon to a range of USB peripherals,
including keyboard and mouse. The Cradles offer the following interfaces: a DC-in port
for the AC-DC adapter, an Ethernet port, a VGA output and USB ports. Always seat the
DT390i securely onto the cradle. The cradle must be powered by the AC-DC adapter
for the Ethernet and USB ports to funcon. The baery packs on the DT390i may be
recharged by connecng the AC-DC adapter directly to the DC-in port on the DT390i or
through the DC-in port on the Cradle while the DT390i is docked.
For More Support
Users can download the Soware Ulity and Modules Operaon Guides from the DT
Research website.
If the DT390i comes with a 3G module, please contact your product and/or service
provider for the SIM Card Slot Locaon and Inseron Guide.
(Picture 1) (Picture 2)