TIC AMP10 User manual

TIC AMP10 Weatherproof
Receiver Amplifier Specifications
Power Supply 110V/DC 12V 4A
AM/FM Tunable
frequency range
FM:87.00MHz-108.00MHz
AM:522KHz-1620KHz
Tunable S/N FM 75dB AM 41dB
Continuous/peak 25W/50W
Frequency
Response
40HZ-16KHZ
AMP S/N >80dB
Sensitivity 1W/1m:80dB
Impedance 4-8ohm
Input AM/FM built in, CD/MP3/other to
phono, ipod/wireless to jack
Output 4x speakers
Supplied Waterproof connector
Color Black
Unit Dimensions 7.9”L×4.7”W×2.2”H
Unit Weight 2.6lbs
Pack
Dimensions
16.1”W×15.0”L×13.4”H(24PCS)
Pack Weight 64lbs(24PCS)
UPC 7 35120 50000 9
Master Carton 8pc.
TIC Corporation engages in continual product research and
development and therefore reserves all rights to change or
improve products specifications without notice
©TIC Corporation
15224 East Stafford Street
City of Industry • CA. • 91744-4418 • U.S.A.
Phone [phone] (5 lines) • Fax [phone]
Website www.ticcorp.com • Email [e-mail]

AMP10 Outdoor Amplifier Features
“Outdoor Sound Solution”
•Weatherproof Design
•Perfect for outdoor speaker listening without
interfering with interior audio speaker set ups
•“Safe” 12v power supply
•Powers 4x outdoor speakers!
•Input CD, MP3 or iPod music!
•Wireless speaker capable
•2x microphone inputs
•Karaoke!
•AM/FM listening!
•Select pre-set radio stations
•Domestic or commercial installs
•ABS impact resistant enclosure
•LCD menu
•Black/ silver finish
Introduction 3
Features & Benefits 3
Product Detail 4
Legend 4
Functions 4
Model Review 5
Pre-Installation 6
Installation 7
Operation 7
Specifications 8
Warranty Registration *encl
Limited Warranty *encl
Thank you!for purchasing another fine product
from TIC Corporation. TIC products are your
“Outdoor Sound Solution”.
TIC Corporation is an Award Winning Original
Designer and Manufacturer of Outdoor Speaker
products and accessories.
You may see the complete line of TIC outdoor
speaker products at www.ticcorp.com .
2 3

AMP10 Receiver Amplifier
Basic Functions
1 & 7 Volume increase or decrease
2 & 8 Radio Tuning
3 Scan Stations
4 AM or FM select
5 Mode
6 Fascia on/ off or pause
9 Preset Stations
10 Select input device
11 Mono or Stereo output
*below: inputs self described
4 5
Upon receiving your new TIC product, please open
packaging carefully and review the unit’s contents.
Your new AMP10 contains
1. 1x AMP10 amplifier unit
2. 1x power cord and converter for
above 220/110 to12v supply
3. 1x cigarette lighter power cord for
12v supply
4. 1x AM & FM antenna wire for the
unit
5. 1x 2.5 jack to 2.5 jack extension
cable
6. 1x instruction booklet
Note! TIC Corporation always recommends you
carefully unpack your new product, inspect contents
and components carefully. Then test the unit using
one or two of your desired input devices and
speakers to ensure correct operation prior to full
exterior installation.

6 7
WARNING!
•There is no requirement for the customer to
open this unit for any kind of operation or
maintenance. Doing so may void the
warranty.
•Ensure rear main power switch is in the
“off” position when not in use.
•Keep the unit away from high temperatures,
excess water, chlorinated solvents or
enclosed areas that prevent natural air pass
cooling or excessive particulate matter.
•Avoid any shocks high vibration or sudden
im
p
acts or collisions to the unit.
11. Carefully unpack your new AMP10 receiver
Amplifier and check all components.
12. TIC always recommends that our customers test
their new purchase prior to any exterior
installation to ensure their familiarity with the
units basic operation before installation.
13. Connect the power mains cable to the AMP10
Amplifier and then to the wall mains 120/110v.
14. Connect your speaker system to the AMP10
prior to switching unit “on”.
15. Attach any input devices (CD/MP3 etc.)
16. Switch the unit “on” using the rear silicone
covered rocker switch.
17. Switch the unit “on” using the front fascia on/off/
pause push switch.
18. Choose your listening “Mode”. Note: the unit is
factory preset in Radio mode to begin initially.
19. Select desired input device or radio/ mic input/
output.
20. Test the unit using as many “modes” of operation
as you can prior to exterior installation.
21. Next, get ready for exterior installation!
1. Carefully, decide where you wish to install your
new TIC AMP10 outdoor amplifier.
2. Installation of your amplifier should consider a
safe, off the ground, dust free position not too far
from a mains outlet and not exposed to excess
water or human traffic conditions.
3. Connect any pre-run speakers or output devices
to your AMP10 amplifier.
4. Connect any input devices such as your CD/
MP3 player etc. to your AMP10 amplifier.
5. Connect the power mains cable to the AMP10
Amplifier and then to the wall mains 120/110v.
6. Switch the unit “on” using the rear silicone
material clear covered rocker switch.
7. Switch the unit “on” using the front fascia on/off/
pause push switch.
8. Choose your listening “Mode”. Note: the unit is
factory preset in Radio mode to begin initially.
9. Select desired input device or radio/ mic input/
output.
10. Test the unit using as many “modes” of operation
as you can to ensure a correct trouble free
exterior installation.
Sit back & Enjoy!
TIC Corporation wishes you many years of
pleasure from your new TIC Corporation
exterior audio product.