TileVision TV/17/FR4/PS User manual

Operating Instructions
PORTER LANCASTRIAN
PORTER LANCASTRIAN LIMITED
www.tilevision.tv
TileVision®is Designed and Manufactured by:
17
®

17" Widescreen TileVision®
A Wide Array of Screen Settings
You can choose different screen settings depending on the type of programme you are
watching or the surrounding conditions (the lighting or the outside weather conditions).
You can switch between Dynamic, Standard, Mild and Game Options, or you can
configure the screen settings yourself. You can select three picture formats; 16:9, 14:9
or 4:3, to match the content you are watching to your preference.
A Wide Array of Sound Settings
You can choose an optimal sound setting for the type of program you are watching.
You can switch between Flat, Music, Movie, and Speech, or you can configure
the settings yourself.
Teletext Function
You can display teletext information at any time on your TileVision®.
This symbol is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO PREVENT INJURY, THIS APPARATUS MUST BE
SECURELY ATTACHED TO THE WALL IN ACCORDANCE
WITH THE INSTALLATION INSTRUCTIONS.
CAUTION: DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
BEWARE OF STATIC SENSITIVE PARTS.
Waste Electrical and Electronic Equipment (WEEE) Directive
In the European Union, this symbol indicates that this product should
not be disposed of with household waste. It should be deposited at an
appropriate facility to enable recovery and recycling.

Safety Instructions
1
Do not use a damaged socket and do not let the power cord
touch a heat source.
–This may cause an electric shock or fire.
Do not attempt to service the unit.
Contact an authorised dealer or repair service.
–Servicing the unit yourself may cause an electric shock or fire.
If there are any unusual sounds or smells coming from the
unit, unplug it immediately and contact an authorised
dealer or repair service.
–This may cause an electric shock or fire.
If an outside antenna is connected to the unit, ensure the
external to internal cable entry is fully sealed
–This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to
an outlet.
–This may cause a fire.
Keep the power adaptor away from any heat source.
–This may cause a fire.
Ensure the antenna is located away from overhead cables.
–This may cause an electric shock.
Do not add an additional screen or cover the TileVision’s glass.
–The heated screen prevents condensation forming in steamy
rooms and covering the screen may cause the unit to overheat.
FAILURE TO OBSERVE THE ABOVE SAFETY WARNINGS MAY INVALIDATE THE WARRANTY

2
Tools Required
Suction Lifter
Clear Silicone Sealant Isopropyl Alcohol
I
s
o
p
r
o
p
y
l
A
l
c
o
h
o
l
Soft Cloth
☛
Silicone Sealant produces acetic acid during cure.
Use only in well ventilated areas. Irritating to eyes.
Wash hands after use and before meals. Wash
splashes from skin, clothing and other surfaces. Use
a clean cloth. In case of contact with eyes wash
immediately with plenty of water.
Please observe safety precautions on the container.
Keep out of reach of children and animals.
☛
Isopropyl alcohol is available from most pharmacies
and larger electronics wholesalers. It is an effective
degreasing agent.
Please observe safety precautions on the container.
Keep out of reach of children and animals.
Do not drink.
HIGHLY
FLAMMABLE
IRRITANT
IRRITANT

Table of Contents
3
Safety Instructions ......................................................................................................................................................1
Tools Required ..............................................................................................................................................................2
Unpacking your TileVision®......................................................................................................................................4
Your TileVision®............................................................................................................................................................5
Connector Inputs ..........................................................................................................................................................5
Connections ....................................................................................................................................................................6
Connecting an Antenna or Cable ..........................................................................................................................7
Connecting to the Component, S-Video and PC Inputs ................................................................................8
Connecting to the SCART Inputs ..........................................................................................................................9
Installing the Front Plate ........................................................................................................................................10
The Remote Control ..................................................................................................................................................11
Switching the TileVision®On/Off ..........................................................................................................................12
Selecting your On-screen Language ..................................................................................................................12
Selecting a Picture from External Sources ......................................................................................................13
Displaying Information ............................................................................................................................................13
On-screen Menus and Displays ..........................................................................................................................14
Tuning, Setup and Editing Programs ................................................................................................................15
Picture Control ............................................................................................................................................................19
Sound Control ............................................................................................................................................................21
Sound Output Selection ..........................................................................................................................................22
PC Picture Adjustment ............................................................................................................................................23
Blue Back ......................................................................................................................................................................25
Auto Sleep and Sleep Timer ..................................................................................................................................25
Child Lock ....................................................................................................................................................................26
ARC (Aspect Ratio Control) ..................................................................................................................................26
The Programme List ................................................................................................................................................26
Teletext ..........................................................................................................................................................................27
Displaying the Teletext Information ....................................................................................................................27
Teletext Button Functions ......................................................................................................................................28
Troubleshooting ..........................................................................................................................................................29
Specifications ..............................................................................................................................................................30
Notes ..............................................................................................................................................................................31

Unpacking your TileVision®
4
Please make sure the following items are
included with your TileVision®.
1 TileVision®glass front plate assembly –complete with Velcro
fixing strips.
1 waterproof remote control.
1 remote control holder.
1 standard full function remote control.
1 installation and instruction manual.
1 mirror acrylic surround.
If any items are missing, contact your dealer.

Your TileVision®
5
Front View
Remote control sensor and indicator
Power Indicator Status
Connector Inputs
DC12V Power In
PC Analog In (D-SUB)
PC Audio In
Headphone Out
Component [Audio L/R, Y, Pb(Cb), Pr(Cr)] In
S-VIDEO In
EURO-SCART (RGB, FB, AV In, AV Out)
Communications Port (Factory use only)
Antenna Input 75Ω
1 2 3 4 5 6 7 8 9
1
2
3
4
5
6
7
8
9
12VDC PC Analog PC
Audio Audio
H/P S-Video AntennaY EURO-SCART Pb(Cb) Pr(Cr)L R
Component
Comm.
Status
Stand-by
Power on
Remote control
Indicator
Red
Green
Red blinking

Connections
6
Earthing Points
The Earthing connection points are found on the rear of the front plate and are clearly marked
with green labels. Connect the earthing cables from the back box to these points.
Power Socket
The Power socket (1) is located at the extreme left of the connection array.
Speaker Connections
The speakers should be connected after the
Earth straps to the rear of the front plate as
detailed on page 10 of these operating
instructions.
The speaker connection block is found on the
right of the rear of the front plate. Lift one of
the lugs, push one conductor of the speaker
lead into the connector, release the lug and
give the lead a slight pull to make sure that it
is gripped correctly. The other wires are connected in the same way.
Note: To ensure that the speakers are in correct phase, the conductor with the stripe should be
connected to the negative terminal (L–or R–) and the plain conductor should be connected to the
corresponding positive terminal (L+ or R+).
Connections to the speakers terminals should be made in the same way –striped conductor to
the negative terminal and plain conductor to the positive terminal.
Antenna Feed
The Antenna input jack is found at the extreme right of the connection array (refer to page 7). A
minimum signal level of 60dBu/1mV is required to avoid a noisy picture.
Additional connections
Connectors for; PC (D-SUB), Audio, SCART, Headphones, S-Video, Component and Audio are
found in the central portion of the connection array. If these inputs are to be utilised the necessary
cables must be installed at the same time as the back box (refer to pages 8 and 9 of these
instructions).
Note: Careful consideration should be given to use of these inputs prior to the installation
of the unit.
Speaker Connection Block
L–L+ R+ R–

Connecting an Antenna or Cable
7
1 Connect the antenna or input cable to the 75Ωcoaxial input
on the rear of the TileVision®.
2 If you are using an indoor antenna, you may need to turn it
when tuning your television until you receive a clear picture.
or
Cable Television
Network
Rear of the
TileVision
®
Antenna
To view television channels correctly, a signal must be received by the set from one of
the following sources: an outdoor antenna, a cable television system or a satellite dish.
☛
The signal level fed to the set must be at least
60dBu/1mV or the picture may be noisy.
If in doubt, consult a qualified aerial technician.

All connections must be made before sealing the front plate into the back box.
Connecting to Component, S-Video and PC Inputs
8
All connections must be made prior to sealing the front plate into the back box.
(A) For Component Input
1 Connect the component video cable and audio L/R cable to the Y/Pb(Cb)/Pr(Cr) and Audio L/R
inputs on the TileVision®and outputs on the external equipment such as DVD player.
(B) For S-Video Input
1 Connect the S-Video/RCA and audio L/R cable to the inputs on the TileVision®and outputs
on the external equipment such as a VCR, camcorder and some video game devices.
2 If the external equipment has mono audio output, connect it only to the left socket of the Audio
Input/Output.
PC Analog Input
1 Connect the PC Analog cable (D-SUB) from the RGB output socket of the PC to the PC input
socket of TileVision®.
2 Connect the PC Audio cable from the PC to the PC Audio in socket of the TileVision®.
Video Game Console
DVD Player
VCR
Audio
S-Video Y Pb(Cb) Pr(Cr)L R
Component
12VDC PC Analog PC
Audio Audio
H/P S-Video AntennaY EURO-SCART Pb(Cb) Pr(Cr)L R
Component
Comm.
(A) For Component Input
(B) For S-Video Input

Connecting to the SCART Input
9
The EURO-SCART socket can be connected to equipment with RGB or composite video inputs and
outputs. A VCR, satellite or cable receiver, DVD player, or video game console should be connected
using the EURO-SCART connection.
◆
The EURO-SCART socket is fully connected as shown above.
◆
The audio output from the EURO-SCART can be connected to a separate amplifier to allow
integration with a multi-room audio video system. This should be carried out by a qualified engineer.
◆
Adaptors are commercially available to allow video and audio equipment to be connected to the
TileVision®via the EURO-SCART socket.
See the examples in diagrams B and C.
◆
The 3.5 mm stereo Headphone socket provides a variable volume audio output which can be
connected to the auxiliary input of an audio amplifier.
◆
If the TileVision®is not being installed in a bathroom an extension lead can be connected to the
Headphone socket. The other end of the extension lead should be terminated at a surface mounted
socket of the appropriate type.
DVD Player
VCR
Video Game Console
Satellite receiver
19
17
15
13
11
9
7
5
3
1
20
18
16
14
12
10
8
6
4
2
21
S-Video AntennaY EURO-SCART Pb(Cb) Pr(Cr)
R
Component
Comm.
(A) SCART to SCART connector
(RGB Video + Audio L/R or
Composite Video + Audio L/R)
(B) SCART to RCA connectors
(Composite Video + Audio L/R)
(C) SCART to RCA adaptor
(Composite Video + Audio L/R)
SCART Pinouts
(solder side view)
All connections must be made before sealing the front plate into the back box.
SCART Connection Reference
Pin Name Description
1 AOR Audio Out Right
2 AIR Audio In Right
3 AOL Audio Out Left + Mono
4 AGND Audio Ground
5 BGND RGB Blue Ground
6 AIL Audio In Left + Mono
7 B RGB Blue
8 SWTCH Audio, RGB switch,16:9
9 GGND RGB Green Ground
10 CLKOUT Clock Out
11 G RGB Green
12 DATA Data Out
13 RGND RGB Red Ground
14 DATAGND Data Ground
15 R RGB Red
16 BLNK Blanking Signal
17 VGND Composite Video Ground
18 BLNKGND Blanking Signal Ground
19 VOUT Composite Video Out
20 VIN Composite Video In
21 SHIELD Chassis Ground, Cable Shield

Installing the Front Plate
10
Checking back box prior to installation of front plate
Before commencing the installation of the front plate the polystyrene-blanking panel must be removed
from the back box. The next step is to ensure that the appropriate cables and their connectors are
present within the back box.
It is important to ensure that the flange inside the back box is cleaned using a grease removal agent and
allowed to dry. The space between the back box and front plate must be even on all 4 sides. If the
flange needs to be straightened, this must be done before proceeding any further. This is very important,
as any damage will affect the unit’s waterproofing capabilities.
Installation of the front plate
Remove the front plate from its packaging and place the remote control to one side.
Introduce the lower front edge of the unit into the box and fit the earth straps to the two Earthing screws
as indicated by the green labels on the rear of the front plate. Connect all cables to their respective
sockets (refer to pages 6 to 9 of these instructions).
The next step is to remove the soft adhesive protector from the top length of special Velcro‚and press
the front plate into the back plate (it may be necessary to adjust the position of the cables to achieve a
good fit).
The unit installation must comply with all relevant electrical safety regulations before turning the mains
supply to the 12VDC power adaptor on using the remote pull switch. The unit should now show a red
indicator light showing that it is in standby mode.
The next step is to tune the unit as detailed on pages 15 to 18.
Once you are satisfied that the unit is tuned and working correctly, press the Power 0/I button on the
remote control to put the unit in standby mode and isolate the unit using the remote pull switch.
Gently remove the front plate using a suction lifter; please do not use a lever to remove the front plate
as this will invalidate your guarantee. Next, remove the self-adhesive protectors from the side and
bottom Velcro strips and press the front panel into the back box with reasonable force. Take care to
apply force to all 4 sides of the box. Restore mains power using the remote pull switch and press the
Power 0/I button on the remote control to turn the unit on again and check that it is still working correctly.
Sealing the unit
When you are sure that the unit is installed correctly put it in standby mode and apply a clear silicone
sealant to the joint between the sides of the back box and the sides of the front plate. Ensure that the
silicone is worked into the gap evenly and is applied without any gaps, bubbles, etc. Wipe any excess
silicone away; check visually for any gaps or bubbles and rectify if necessary. This seal is of the greatest
importance to the reliable and safe operation of this unit and must be waterproof.
Sealing Tip: To achieve a neat seal easily it is good practice to use
masking tape around the TileVision
®
glass screen and the surrounding
tiles, just leaving sufficient gap to apply the silicone sealant around the
joint between the sides of the back box and front plate.
The acrylic
bezel can be fitted using silicone sealant once the tape is removed.
Note: It is the installer’s responsibility to ensure that the TileVision®
unit is installed and sealed correctly, failure to do so will invalidate
your guarantee. The unit will require cleaning and re-sealing after any
servicing/repair operation.
Cleaning Instructions
To clean the front screen, use only a soft damp cloth. Under no circumstances are abrasive
cleaners to be used, failure to observe this warning will invalidate your guarantee.
Note: A glass carrier/suction lifter is required.
Tile
Back box Grout
Velcro
Masking tape
Silicone
Screen

Remote Control
11
☛
Make sure there are no
objects between the
remote control and
its sensor.
Do not place the remote
control near a heater.
A strong blow to the
remote control may cause
it not to operate.
1 Power On/Off button
Turns the TileVision®on or off from standby
2 PSM (Picture Status Memory) button
Recalls the preferred picture setting
3 SSM (Sound Status Memory) button
Recalls the preferred sound setting
4 Mute button
Turns the sound on or off
5 Number buttons
Selects programme numbers
6 OK button
Accepts your selection or displays the current mode
7 VOL (Volume) buttons
Adjust the volume and selects/adjusts Menu Items
8 PR (Programme up/down) buttons
Selects next or previous programme or
Menu Item
9 Menu button
Displays the Main Menu
10 Teletext On/Off/Mode button
See page 28 for Teletext function table
(buttons 10 to 15)
11 Teletext Mix button
12 Teletext Hold button
13 ARC (Aspect Ratio Control) button. Three picture formats
are available: 16:9,14:9 and 4:3. Press the ARC Button
repeatedly to select the desired format
Note: only 16:9 and 4:3 are available in PC mode
14 Teletext Sub-page and Time button
Press to display the time when viewing TV programmes
15 TV/AV button
Selects between TV, SCART, S-VIDEO, COMPONENT or
PC mode. Clears the menu from the screen
16 Red FastText button
17 Green FastText button
18 Yellow FastText button
19 Blue FastText button
SSM
OK
MENU
PR VOL
TIME
TEXT MIX HOLD
PSM
ARC TV
/AV
4
5
6
7
19
8
9
1 2 3
10 11 12
13 14 15
16 17 18

Switching the TileVision®On/Off
12
SSMPSM
1 To switch your TileVision®on, press the POWER ( ) button.
2 To switch your TileVision®to standby, press the POWER ()
button again.
OK
MENU
PR VOL
Setup
Auto programme
Manual programme
Programme edit
Language
Language
English Svenska
Deutsch Magyar
Français Romaneste
Español Cesky
Italiano Polski
Nederlands
Português
Dansk Türkçe
Suomi Hrvatski
Norsk
Selecting your On-screen Language
When you start using your TV for the first time, you must select the language in which to
display all on-screen menus.
1 Press the MENU ( ) button.
2 Press the PR UD buttons to select the Setup menu and then
press the VOL R button.
3 Press the PR UD buttons to select the Language menu and
then press the VOL R button.
4 Press the PR UD , VOL L R buttons to select your desired
language.
5 Press TV/AV to exit the menus and confirm settings.
All the on-screen displays will now appear in the selected
language.
MENU

Selecting a Picture from External Sources
13
You can display the programme information and settings status
currently in use.
1 Press the OK ( ) button.
OK
After your various systems (audio and video) have been connected, you can view any of the
sources by selecting the appropriate external input.
1 Make sure all the necessary connections have been made.
2 Press the POWER ( ) button to switch the device on.
3 Press the TV/AV or PR UD buttons to select the required
external input mode –TV, SCART, S-VIDEO, COMPONENT, or
PC ANALOG.
4 Press the OK ( ) button to select your desired mode.
OK
TIME
ARC TV
/AV
Input Selection
TV
SCART
S-VIDEO
COMPONENT
PC ANALOG
P 1--------- 16:9
Mono Flat
Dynamic --
Displaying Information

On-screen Menus and Displays
14
Picture
Colour Temperature
Contrast 75
Brightness 65
Colour 75
Sharpness 80
Sound
Equalizer
Balance 0
AVL Off
Surround Off
Headphone 30
Special
Blue Back On
Auto Sleep Off
Child Lock Off
Setup
Auto programme
Manual programme
Programme edit
Language
Colour Temperature
Standard
Reddish
Greenish
Bluish
User RGB
Auto Programme
Country Great Britain
System BG
Storage From 1
Start
Manual Programme
Programme 1
System BG
Channel V/UHF 69
Name --------
Finetune 0
Memorize
Programme Edit
P001--------- P006---------
P002--------- P007---------
P003--------- P008---------
P004--------- P009---------
P005--------- P010---------
■Delete ■Favourite
■Move ■Skip
Main menu
Picture
Sound
Special
Setup
Equalizer
Flat
Music
Movie
Speech
User 0.1 0.5 1.5 5.0 10Khz
SSM
OK
MENU
PR VOL
TIME
TEXT MIX HOLD
PSM
ARC TV
/AV
1 Press the MENU button to display the Main menu.
2 Press the PR UD buttons to select menus.
3 Press VOL LR buttons to adjust menu items.
4 Press MENU to go back to the previous menu.
5 Press TV/AV to exit the menus and confirm settings.

Tuning, Setup and Editing TV Programmes
15
Auto Programme
1 Press the MENU button.
2 Press the PR UD buttons to select the Setup menu and then
press the VOL R button.
3 Press the PR UD buttons to select the Auto Programme menu
and then press the VOL R button.
4 Select the Country with the VOL LR buttons. Choose from:
Austria, Belgium, Switzerland, Czech Rep, Germany, Denmark,
Spain, France, Finland, Great Britain, Greece, Hungary, Italy,
Norway, Netherlands, Portugal, Poland, Sweden, Slovenia,
Slovakia, Turkey, others.
5 Press the PR UD buttons to select the System.
6 Select a TV system with the VOL LR buttons:
BG: Western Europe/Asia/Middle East/Africa/Australia
I: UK/Hong Kong/South Africa
DK: Russia/China/Eastern Europe
L: France.
7 Press PR UD buttons to select Storage From.
8 Select the beginning programme number with the VOL LR
buttons or NUMBER buttons.
9 Press the PR UD buttons to select Start and press the VOL R
button to confirm. The Auto Programme will now start, this will
take a few minutes to complete.
To delete, skip, move or name the stored programmes see
Programme Edit, on page 16.
Main menu
Picture
Sound
Special
Setup
Setup
Auto programme
Manual programme
Programme edit
Language
Auto Programme
Country Great Britain
System BG
Storage From 1
Start
Note: It is recommended that Auto Programme is used when installing TileVision®as all
available programmes will be stored.
OK
MENU
PR VOL

Tuning, Setup and Editing TV Programmes
16
Manual Programme
01 Press the MENU button.
02 Press the PR UD buttons to select the Setup menu and then
press the VOL R button.
03 Press the PR UD buttons to select the Manual Programme
menu and then press the VOL R button.
04 Select the programme with the VOL LR buttons or number
buttons.
05 Press the PR UD buttons to select the System.
06 Select a TV system with the VOL LR buttons:
BG: Western Europe/Asia/Middle East/Africa/Australia
I: UK/Hong Kong/South Africa
DK: Russia/China/Eastern Europe
L: France
07 Press PR UD buttons to select Channel. Then, press the
VOL LR buttons.
08 Press the PR UD buttons to select the V/UHF or Cable as
required. If possible select the programme number directly with
the number buttons.
09 Press PR UD buttons to select the Name. Then press the
VOL LR buttons.
You can assign a programme name with up to eight characters.
Press the PR
UD button repeatedly.
You can use the numbers 0 to 9, the alphabet from A to Z, and
a blank.
With the VOL
LR buttons you can select in the opposite
direction.
10 Press PR UD buttons to select Finetune.
Press the VOL R button to commence fine tuning.
11 Press PR UD buttons to select memorize.
12 Press the VOL R button or OK button to store it.
13 Press the Menu button to return to the previous menu.
14 Press the TV/AV button to return to normal TV viewing.
Main menu
Picture
Sound
Special
Setup
Setup
Auto programme
Manual programme
Programme edit
Language
Manual Programme
Programme 1
System BG
Channel V/UHF 69
Name --------
Finetune 0
Memorize
Manual Programme lets you tune and arrange the programmes in any order you want.
You can assign an eight character programme name to each programme number.
OK
MENU
PR VOL

Tuning, Setup and Editing TV Programmes
17
Programme Edit
This function enables you to delete, make favourite, move or skip
the stored programmes.
You can also move channels to different programme numbers, or
insert blank programme data into the selected programme number.
1 Press the MENU button.
2 Press the PR UD buttons to select the Setup menu and then
press the VOL R button.
3 Press the PR UD buttons to select Programme Edit and then
press the VOL R button.
4 Select the programme name to edit with the PR UD buttons
and VOL LR buttons.
Deleting a programme
1 Select a programme to be deleted with the PR UD or
VOL LR buttons.
2 Press the RED button once. The selected programme is deleted,
all the following programmes shift up one position.
Selecting a favourite programme
1 Select a favourite programme with the PR UD buttons or
VOL LR .
2 Press the GREEN button.
This function lets you select your favourite programme directly.
Main menu
Picture
Sound
Special
Setup
OK
MENU
PR VOL
Setup
Auto programme
Manual programme
Programme edit
Language
Programme Edit
P001--------- P006---------
P002--------- P007---------
P003--------- P008---------
P004--------- P009---------
P005--------- P010---------
■Delete ■Favourite
■Move ■Skip
TIME
ARC TV
/AV
☛
FAV+/– buttons are only available on the full
function standard remote control, press these
buttons to select the stored favourite programme.

Tuning, Setup and Editing TV Programmes
18
Moving a programme in Programme Edit menu
1 Select a programme to be moved with the PR UD or
VOL LR buttons.
2 Press the YELLOW button.
3 Move the programme to the desired programme number with the
PR UD or VOL LR buttons.
4 Press the YELLOW button again to release this function.
Skipping a programme number in Programme
Edit menu
1 Select a programme to be skipped with the PR UD or
VOL LR buttons.
2 Press the BLUE button. The skipped programme turns blue.
3 Press the BLUE button again to release the skipped programme.
☛
When a programme number is skipped it means
that you will be unable to select it using the PR UD
buttons during normal TV viewing.
If you want to select the skipped programme, enter
the programme number with the NUMBER buttons,
or select it in the programme edit menu.
TIME
ARC TV
/AV
TIME
ARC TV
/AV