Timberwolf TW PTO/100G User manual

timberwolf-uk.com
INSTRUCTION MANUAL
TW TO/100G WOOD CHI ER

© Copyright Entec Industries Ltd 2015
The content of this publication may not be copied, reproduced, republished, posted, broadcast, transmitted
or used in any way in any medium without the written permission of Entec Industries Ltd.

CONTENTS
TIMBERWOLF
TW PTO 100G
10.04.2017
Section Page No.
INTRODUCTION 1
PURPOSE OF MACHINE 2
MACHINE DIMENSIONS & SPECIFICATIONS 2
PARTS LOCATION DIAGRAMS 3
SAFE WOR ING 5
Operator’s Personal Protective Equipment Required 5
Basic Woodchipping Safety 5
General SafetyMatters - Do’s and Dont’s 6
Noise Test 7
OPERATING INSTRUCTIONS 8
Safe Transportation 8
Delivery 8
Operator’s Personal Protective Equipment Required 8
Hitching Up 8
Connecting PTO Shaft 9
Daily Checks Before Starting 9
Starting to Chip 9
Chipping 9
Blade Wear 10
Blockages 10
SERVICE INSTRUCTIONS 11
Service Schedule 12
Spares 12
Copper Ease Safety Information 12
Safe Maintenance 13
Check Fittings 13
Tension Drive Belts 13
Anvil Changing 13
Change Rotor Bearings 13
Change Blades 14
Change Gear Box Oil 14
Check Wheel Grease Points 14
Safe Lifting of the Chipper 14
WARRANTY STATEMENT 15
EC DECLARATION OF INCORPORATION CERTIFICATE 16
IDENTIFICATION PLATE 17
DECALS 18
V- BELT TENSIONING TABLE 20
PARTS LISTS 22
WARRANTY SERVICE CHEC RECORD 28
SERVICE RECORD 29

TIMBERWOLF
TW PTO 100G
1
Thank you for choosing Timberwolf. Timberwolf chippers are designed to give safe and
dependable service if operated according to the instructions.
IMPORTANT HEALTH AND SAFETY INFORMATION
Before using your new chipper, please take time to read this manual. Failure to do
so could result in:
- PERSONAL INJURY
- EQUIPMENT DAMAGE
- DAMAGE TO PROPERTY
- 3RD PARTY INJURIES
This manual covers the operation and maintenance of the Timberwolf TW PTO/100G. All
information in this manual is based on the latest product information available at the time
of purchase.
All the information you need to operate the machine safely and effectively is contained
within pages 2 to 10. Ensure that all operators are properly trained for operating this
machine, especially safe working practices.
Timberwolf's policy of regularly reviewing and improving their products may involve major
or minor changes to the chippers or their accessories. Timberwolf reserves the right to
make changes at any time without notice and without incurring any obligation.
Due to improvements in design and performance during production there may be, in
some cases, minor discrepancies between the actual chipper and the text in this manual.
The manual should be considered an important part of the
machine and should remain with it if the machine is resold.
CAUTION or WARNING
BE A ARE OF THIS SYMBOL AND HERE
SHO N, CAREFULLY FOLLO
THE INSTRUCTIONS.
This caution symbol indicates important safety messages in this manual.
When you see this symbol, be alert to the possibility of injury to yourself
or others and carefully read the message that follows.
AL AYS FOLLO SAFE OPERATING AND MAINTENANCE PRACTICES
INTRODUCTION

TIMBERWOLF
TW PTO 100G
2
Serial No. Location
The serial number can
be found on top of the
rotor housing.
The Timberwolf PTO/100G brushwood chipper is designed to chip solid wood material including
timber branches, saplings and brushwood up to 100mm in diameter.
The Timberwolf PTO/100G brushwood chipper is required to be securely coupled to the pin hitch
of an 18 - 40hp compact tractor unit with 540rpm PTO when in use. Power from the attached
compact tractor unit is to be supplied to the chipper via PTO drive shaft.
DIMENSIONS
2050mm, (1570mm with discharge removed)
2460mm, (1935mm with feed tray closed)
1000mm
TIMBERWOLF TW PTO/100G SPECIFICATION
Power source Tr ctor PTO drive
PTO speed 540rpm
Overall weight 270kg
Type of feed Gr vity
Maximum diameter material 100 mm (4”)
Material processing capacity 1 tonne/hr
Required engine power 18 - 40hp
The Timberwolf TW PTO/100G

FEED
FUNNEL
DISCHARGE
BUC ET
ROTOR
HOUSING
BELT
GUARD
TOW HEAD
PTO SHAFT
GUARD
PTO SHAFT
STAND
DISCHARGE
TUBE
DISCHARGE
CLAMPS
FRONT
SUPPPORT
TIMBERWOLF
TW PTO 100G
3
PARTS LOCATOR

ROTOR
FAN SECTION (X2)
CUTTER BLADE (x2)
ROTOR DRIVE
PULLEY
REAR BEARING
FRONT BEARING
GEARBOX
BELTS
BREATHER PIPE
TIMBERWOLF
TW PTO 100G
4
PARTS LOCATOR

TIMBERWOLF
TW PTO 100G
5
BASIC WOODCHIPPING SAFETY
The operator should be aware of the following points:
MAINTAIN A SAFETY EXCLUSION ZONE around the chipper of at least 10 metres for the
general public or employees without adequate protection. Use hazard tape to identify this
working area and keep it clear from debris build up. Chips should be ejected away from any
area the general public have access to.
HAZARDOUS MATERIAL - Some species of trees and bushes are poisonous. The chipping
action can produce vapour, spray and dust that can irritate the skin. This may lead to
respiratory problems or even cause serious poisoning. Check the material to be chipped before
you start. Avoid confined spaces and use a facemask if necessary.
BE AWARE when the chipper is processing material that is an awkward shape. The material can
move from side to side in the funnel with great force. If the material extends beyond the funnel,
the brash may push you to one side causing danger. Badly twisted brash should be trimmed
before being chipped to avoid thrashing in the feed funnel.
BE AWARE that the chipper can eject chips out of the feed funnel with considerable force. Always
wear full head and face protection.
ALWAYS work on the side of the machine furthest from any local danger, e.g. not road side.
WARNING
SAFE WORKING
The chipper will feed material through on its own. To do this, it relies on sharp
blades both on the feed rollers and the chipper rotor. To keep the blades sharp,
only feed the machine with clean brushwood. DO NOT put muddy/dirty wood,
roots, potted plants, bricks, stones or metal into the chipper.
OPERATOR'S PERSONAL PROTECTI E EQUIPMENT REQUIRED
Chainsaw safety helmet fitted
with mesh visor and
recommended ear defenders to
the appropriate specifications.
Work gloves with elasticated
wrist.
Close fitting heavy-duty
non-snag clothing.
Face mask if
appropriate.
DO NOT
wear rings, bracelets, watches,
jewellery or any other items that
could be caught in the material
and draw you into the chipper.
Steel toe cap safety boots.

TIMBERWOLF
TW PTO 100G
6
ü
SAFE WORKING
GENERAL SAFETY MATTERS
D O ’ S A N D D O N ’ T S
DO NOT operate chipper unless available light is
sufficient to see clearly.
DO NOT attempt to engage PTO without the feed
funnel, belt guard, guards and discharge unit
securely in place.
DO NOT stand directly in front of the feed funnel
when using the chipper. Stand to one side.
DO NOT allow -
DO NOT smoke when refuelling.
DO NOT let anyone who has not received
instruction operate the machine.
DO NOT climb on the machine at any time.
DONOT handle material that is partially engaged
in the machine.
DO NOT touch any exposed wiring while machine
is running.
DO NOT use the chipper inside buildings.
- to enter the machine, as damage is likely.
ALWAYS stop the tractor engine, remove ignition
key and disconnect the PTO shaft before making
any adjustments.
ALWAYS check machine has stopped rotating and
remove tractor ignition key before maintenance of
any kind, or whenever the machine is to be left
unattended.
ALWAYS check machine is securely coupled to
tractor pin hitch and on firm level ground.
ALWAYS run tractor engine at required speed to
acheive correct PTO speed.
ALWAYS check (visually) for fluid leaks.
ALWAYS take regular breaks. Wearing personal
protective equipment for long periods can be
tiring and hot.
ALWAYS keep hands, feet and clothing out of feed
opening, discharge and moving parts.
ALWAYS use the next piece of material or a push
stick to push in short pieces. Under no
circumstances should you reach into the funnel.
ALWAYS keep the operating area clear of people,
animals and children.
ALWAYS keep the operating area clear from
debris build up.
ALWAYS keep clear of the chip discharge tube.
Foreign objects may be ejected with great force.
ALWAYS ensure protective guarding is in place
before commencing work. Failure to do so may
result in personal injury or loss of life.
ALWAYS operate the chipper in a well ventilated
area - exhaust fumes are dangerous.
BRIC S STRING CLOTH PLASTIC STONES
METAL GLASS RUBBER ROOTS BEDDING
PLANTS
ü

TIMBERWOLF
TW PTO 100G
7SAFE WORKING
NOISE TEST
MACHINE: TW PTO/100G
NOTES: Tested chipping green conifer 25 mm-40 mm
Noise levels above 80dB (A) will be experienced at the working position. ear ear protection
at all times to prevent possible damage to hearing. All persons within a 4 metre radius must also
wear good quality ear protection.
91.2 dB
96.7 dB
101 dB
R= 4 metres
Guaranteed Sound Power: 125dB (A)
As required by Annex III of Directive 2000/14/EC “Noise Emission in the environment by equipment for use outdoors”.
R= 10 metres
9
5
d
B
C
a
l
c
u
l
a
t
e
d
9
5
d
B
C
a
l
c
u
l
a
t
e
d
9
5
d
B
C
a
l
c
u
l
a
t
e
d
95.5 dB
109.3 dB
97.6 dB

OPERATING INSTRUCTIONS 8
TIMBERWOLF
TW PTO/100G
All Timberwolf TW PTO/100G m chines h ve full pre - delivery inspection before le ving the f ctory
nd re re dy to use. Re d nd underst nd this instruction m nu l before ttempting to oper te the
chipper. In p rticul r, re d p ges 5-7 which cont in import nt he lth nd s fety inform tion nd dvice.
CHAINSAW safety helmet fitted with visor
and recommended ear defenders to an
appropriate specification.
HEAVY-DUTY gloves with elasticated wrist area.
CLOSE - FITTING heavy-duty non-snag clothing.
SAFETY footwear.
FACE MAS (if appropriate).
See p ge 5 for more det iled inform tion.
DELI ERY
OPERATOR’S PERSONAL PROTECTI E EQUIPMENT REQUIRED
HITCHING UP
THE PTO/100G chipper may be transported as a unit or with the feed funnel removed.
TA E care when loading the PTO/100G as it is 268kg in weight.
STRAP the chipper down firmly before beginning a journey.
SAFE TRANSPORTATION
The first time a tractor is fitted to the chipper the
correct length of tow beam needs to be set. The
length corresponds to the exact propeller shaft that is
to be used. Adjustment is made underneath the
chipper. Remove the M12 bolt from underneath the
chassis (1) and slide the bar until the desired length is
reached. Replace the bolt and tighten.
The PTO/100G is fitted with a pin type hitch. It is
suitable for use with a range of compact tractor with a
540rpm PTO output. The chipper tow head is fitted
onto the tractor coupling for use with a steel pin (1)
which is dropped through the hole. This should be
retained with an R clip (2) for security.
The front leg that keeps the chipper level and provides
support for the propeller shaft is movable. After
hitching to a tractor and fitting the prop shaft the bolt (3)
can be removed and the leg swung horizontal. The
bolt is then refitted in hole shown (4).
1
2
3
4
1
(not supplied)
(not supplied)
WARNING ALWAYS ENSURE THE TRACTOR ENGINE IS TURNED OFF AND EY
REMOVED FROM IGNITION BEFORE PERMORMING ANY
ADJUSTMENTS TO CHIPPER

TIMBERWOLF
TW PTO 100G
9OPERATING INSTRUCTIONS
CONNECTING PTO SHAFT
LOCATE the machine on firm level ground and correctly coupled to a tractor.
CHEC all guards are in place and PTO guard anti rotation chain is secured.
CHEC the discharge unit is pointing in a safe direction.
CHEC the feed funnel to ensure no objects are inside.
For p rts loc tion see di gr ms on p ges 3 & 4.
DAILY CHECKS BEFORE STARTING
CHEC that the chipper is running smoothly at correct PTO speed.
STAND to one side of the feed funnel when loading material.
PROCEED to feed material into the feed funnel (note do's and dont's).
Wood up to 100 mm in diameter can be fed into the feed funnel. Enter it into the funnel butt end first.
Release the material before it engages the rotor. Some pieces of wood may move around significantly
while being chipped.
The wood will be drawn into the cutting blade quite quickly, be ready for this to happen. Stand well clear.
A piece of wood which is too tough or too large for the chipper will slow the engine down. When this
happens it is possible to hold back the branches that are being chipped and allow the engine to regain
its speed again.
If a piece of wood gets stuck in the funnel and it cannot be chipped due to its size or shape, it will need
to be removed. Trim the branch until it is a suitable shape for the chipper to accept.
STARTING TO CHIP
CHIPPING
WARNING Do not use or attempt to start the chipper without the protective
guarding and discharge unit securely in place. Failure to do so may
result in personal injury or loss of life.
ALWAYS ENSURE THE TRACTOR IS TURNED OFF BEFORE FITTING OR REMOVING PROP SHAFT.
When fitting a PTO shaft it should always be remembered that 100 mm of overlap is required between
the two sections of the shaft. This is the minimum needed to ensure the shaft does not fail.
To connect the PTO shaft follow the instructions supplied with the shaft. The shaft should remain fitted
to the chipper at all times. It can be placed on the prop shaft support when the tractor is removed.

TIMBERWOLF
TW PTO 100G
10
OPERATING INSTRUCTIONS
BLADE WEAR
The most important part of using a wood chipper is keeping the cutter blades sharp. Timberwolf
chipper blades are hollow ground to an angle of 40 degrees. When performing daily blade checks
ensure blade edge is sharp and free from chips, if there is any evidence of damage, or the edge is “dull”
change the blade(s). The TW 13/75G is fitted with two blades 177 mm (7") long. They are 43 mm wide
when new. A new blade should chip for up to 25 hours before it requires sharpening. This figure will
be drastically reduced by feeding the machine with stony, sandy or muddy material.
As the blade becomes blunt performance is reduced, with increased stress and load on the machine
the chips will become more irregula rand stringy. At this point the blade should be sent to a reputable
blade sharpening company. The blade can be sharpened several times in its life. A wear mark on the
reverse side indicates the safe limit of blade wear. Replace when this line is exceeded.
The machine is also fitted with a static blade (anvil). It is important that the anvil is in good condition
to allow the cutting blades to function efficiently. Performance will be poor, even with sharp cutter
blades, if the anvil is worn.
STOP the tractor engine and remove the ignition keys.
ENSURE tractor engine has come to a complete stop.
REMOVE the discharge tube. Check that it is clear.
WEARINGgloves, reach into the rotor housing and scoop out the majority of the debris
causing the blockage.
REPLACE the discharge tube.
RESTART the tractor engine and increase revs to achieve PTO speed of 540 rpm.
ALLOW machine time to clear excess chips still remaining in rotor housing before you continue
feeding brushwood. Feed in a small piece of wood while watching to make sure that it comes
out of the discharge. If this does not clear it, repeat the process and carefully inspect the
discharge tube to find any obstruction.
NOTE
Continuing to feed the chipper with brushwood once it has become blocked will cause the chipper to
compact the chips in the rotor housing and it will be difficult and time consuming to clear.
AVOID THIS SITUATION - WATCH THE DISCHARGE TUBE AT ALL TIMES.
BLOCKAGES
WARNING Do not reach into the rotor housing with unprotected hands. There
are sharp blades and any small movement of the rotor may cause
serious injury.
WARNING Do not rev engine and increase PTO speed above 540rpm in an
attempt to clear blockages. Always follow procedure as outlined
below to protect operator and bystanders from ejected material.
Always be aware that what you are putting into the chipper must come out. If the chips stop coming out
of the discharge tube but the chipper is taking material in - STOP IMMEDIATELY. Continuing to feed
material into a blocked machine may cause damage and will make it difficult to clear.
If the chipper becomes blocked proceed s follows:

TIMBERWOLF
TW PTO 100G
11
THE FOLLOWING PAGES DETAIL ONLY
BASIC MAINTENANCE GUIDELINES SPECIFIC
TO YOUR CHIPPER.
THIS IS NOT A WOR SHOP MANUAL.
THE FOLLOWING GUIDELINES ARE NOT EXHAUSTIVE AND DO NOT EXTEND
TO GENERALLY ACCEPTED STANDARDS OF ENGINEERING/MECHANICAL
MAINTENANCE THAT SHOULD BE APPLIED TO ANY PIECE OF MECHANICAL
EQUIPMENT AND THE CHASSIS TO WHICH IT IS MOUNTED.
AUTHORISED TIMBERWOLF SERVICE AGENTS ARE FULLY TRAINED IN ALL
ASPECTS OF TOTAL SERVICE AND MAINTENANCE OF TIMBERWOLF
WOOD CHIPPERS. YOU ARE STRONGLY ADVISED TO TA E YOUR CHIPPER TO
AN AUTHORISED AGENT FOR ALL BUT THE MOST ROUTINE MAINTENANCE
AND CHEC S.
TIMBERWOLF ACCEPTS NO RESPONSIBILITY FOR THE FAILURE OF THE
OWNER/USER OF TIMBERWOLF CHIPPERS TO RECOGNISE GENERALLY
ACCEPTED STANDARDS OF ENGINEERING/MECHANICAL MAINTENANCE
AND APPLY THEM THROUGHOUT THE MACHINE.
THE FAILURE TO APPLY GENERALLY ACCEPTED
STANDARDS OF MAINTENANCE, OR THE PERFORMANCE OF
INAPPROPRIATE MAINTENANCE, MAY INVALIDATE
WARRANTY IN WHOLE OR IN PART.
PLEASE REFER TO YOUR AUTHORISED
TIMBERWOLF SERVICE AGENT FOR
SERVICE AND MAINTENANCE.

TIMBERWOLF
TW PTO 100G
12
SER ICE INSTRUCTIONS
WARNING
Always immobilise the machine by stopping the tractor and removing
the ignition key before undertaking any maintenance work. When the
tractor is stopped it will be necessary to disengage the PTO so that
the rotor can be turned.
SER ICE SCHEDULE
Product name: Copper Ease.
Copper Ease contains no hazardous ingredients at or above regulatory disclosure limits, however,
safety precautions should be taken when handling (use of oil-resistant gloves and saftey glasses are
recommended - respiratory protection is not required). Avoid direct contact with the substance and
store in a cool, well ventilated area avoiding sources of ignition, strong oxidising agents and strong
acids. Dispose of as normal industial waste (be aware of the possible existance of regional or national
regulations regarding disposal), do not discharge into drains or rivers.
In case of fire: in combustion the product emits toxic fumes, extinguish with alcohol or polymer foam,
carbon dioxide or dry chemical powder. Wear self-contained breathing apparatus and protective clothing
to prevent contact with skin and eyes.
FIRST AID
Skin contact: there may be mild irritation at the site of contact, wash immediately with plenty of soap and water.
Eye contact: there may be irritation and redness, bathe the eye with running water for 15 minutes.
Ingestion: there may be irritation of the throat, do not induce vomiting, wash out mouth with water
A safety data sheet for this product can be obtained by writing to the manufacturer at the
following address: Comma Oil and Chemicals Ltd., Deering Way, Gravesend, ent DA12 2QX.
Tel: [phone], Fax: [phone].
COPPER EASE SAFETY INFORMATION
SERVICE SCHEDULE
Check feed funnel and belt guard, and PTO
guard are securely fitted. ü
Check blade condition. ü
Check and lubricate PTO shaft. ü
Check for tightness all nuts, bolts and fastenings
making sure nothing has worked loose. ü
Check belt tension, adjust if necessary. ü
Check cutting anvil for wear. ü
Check wheel grease points. ü
Change gear box oil. ü
Replace anvils when worn.
Daily
Check
25
Hours
50
Hours
(once a month)
400
Hours
(once a year)
NOTE: Your Timberwolf wood chipper is covered by a full 12 months parts and labour warranty.
Subject to correct maintenance and proper machine usage, the bearings are guaranteed for 12 months
regardless of hours worked by the machine. In conditions of 'heavy usage' - i.e. in excess of 500 hours
per year - it is recommended that the bearings are changed annually to ensure that the machine retains
optimum working performance.
Refer to PTO leaflet provided.
SPARES
Only fit genuine Timberwolf replacement blades, screws and chipper spares. Failure to do so will result in
the invalidation of the warranty and may result in damage to the chipper, personal injury or even loss of life.
RETURN TO DEALER FOR ANVIL CHANGE

TIMBERWOLF
TW PTO 100G
13 SER ICE INSTRUCTIONS
HANDLE blades with extreme caution to
avoid injury. Gloves should always be
worn when handling the cutter blades.
THE drive belts should be connected
while changing blades, as this will restrict
sudden movement of the rotor.
THE major components of this machine
are heavy. Lifting equipment must be
used for disassembly.
CLEAN machines are safer and easier to
service.
SAFE MAINTENANCE
Size Pitch Head Torque Ibft
Blade Bolts M8 Standard T40 Torq 22
General M8 Standard 13 mm Hex 20
General M10 Standard 17 mm Hex 45
General M12 Standard 19 mm Hex 65
CHECK FITTINGS
The Timberwolf PTO/100G is subject to large vibrations during the normal course of operation.
Consequently there is always a possibility that nuts and bolts will work themselves loose. It is
important that periodic checks are made to ensure the security of all fasteners. Fasteners should be
tightened using a torque wrench to the required torque (see below). Uncalibrated torque wrenches
can be inaccurate by as much as 25%. It is therefore essential that a calibrated torque wrench
is used to achieve the tightening torques listed below.
TENSION BELTS
34
1. Remove the belt guard.
2. Check the belt tension. For instructions on
checking belt tension & correct belt tension
values, please refer to the Timberwolf V-Belt
Tensioning Data Table .
3. Loosen the M12 Bolt.
4. Adjust the belt tension by tightening the nut
clamping the bracket to the base.
5. Re-tighten the M12 Bolt.
6. Refit belt guard.
NOTE:There will normally be a rapid drop in tension during run-in period for new belts. When new
belts are fitted, check the tension every 2 - 3 hours and adjust until the tension remains constant.
Belt f ilures due to l ck of correct tensioning will not be covered under your Timberwolf w rr nty.
The anvil is an important component in maintaining a consistent machine performance. Inspect it with
the feed funnel removed. A measure of the wear is how sharp the edge is. If it has become seriously
rounded then it is appropriate to change it.
Turning or repl cing the nvil should be c rried out by Timberwolf de ler.
AN IL CHANGING
CHANGE ROTOR BEARINGS
Return the chipper to your dealer.
N.B. E rly models were fitted with ge rbox on slider. The belt tensioner for these models is
loc ted on the slide pl te.

TIMBERWOLF
TW PTO 100G
14
SER ICE INSTRUCTIONS
CHANGE BLADES
WARNING Wear riggers gloves for the blade changing operation.
WARNING Always sharpen blades on a regular basis. Failure to do so
will cause the machine to under perform and will overload
engine and bearings causing machine breakdown. Blades
must not be sharpened beyond the wear mark (see diagram).
Failure to comply with this could result in machine damage,
injury or loss of life. WEAR
MAR
1. Remove the feed funnel.
2. Insert M10 screw into rotor to stop it turning.
3. Use a small screwdriver to remove sap and
debris from Torx socket in screw - be
particularly careful to ensure every last piece
has been removed.
4. Using the Torx fitting provided loosen the
blade screws.
5. Remove the blade carefully.
6. Before fitting a new blade ensure the
seating surface on the rotor is spotlessly
clean. This is necessary to ensure the
blade is always held firm. Damage to the
rotor may be caused if this is not checked.
7. Apply a small amount of copper grease to the
blade screws.
8. Using a torque wrench tighten the blade
screws to 29Nm (22 lb/ft).
2
8
1. Remove the belt guard.
2. Locate the drain plug underneath the gear box.
3. Drain out oil and replace plug.
4. Add 560ml oil (EP80/90) via top filler/breather plug.
1. Locate grease nipples attached to wheel hubs.
2. Apply 5 shots of general purpose grease.
2
4
1
The lifting eye is designed to lift the machine’s weight only. Do not use
hoist hook directly on the lifting eye, use a correctly rated safety shackle.
Inspect the lifting eye prior to each use - DO NOT USE LIFTING EYE IF
DAMAGED.
SAFE LIFTING OF THE CHIPPER
CHECK WHEEL GREASE POINTS
CHANGE GEAR BOX OIL

TIMBERWOLF
TW PTO 100G
15 WARRANTY STATEMENT
ENTEC INDUSTRIES LTD 36 MONTH WARRANTY
WARRANTY
The warranty period for your Entec Industries Ltd machine commences on the date of sale to the first
end user and continues for a period of 36 months. This guarantee is to the first end user only and is not
transferable except when an Authorised Timberwolf Dealer has a machine registered with Entec
Industries Ltd as a hire chipper or long term demonstrator – in these situations they are duly authorised
to transfer any remaining warranty period to their first end user. Any warranty offered by the Timberwolf
Dealer beyond the original 36-month period will be wholly covered by said Dealer.
LIABILITY
No liability will be accepted for special, indirect, incidental, or consequential loss or damages of any kind.
Our obligation under this warranty is limited to repair at Entec Industries Ltd Authorised Timberwolf
Dealers or at Entec Industries Ltd premises.
WARRANTY STATEMENT
Entec Industries Ltd warrants to the first end user that:
Your machine shall be designed, built and equipped, at the point of sale, to meet all current•
applicable regulations.
Your machine shall be free from manufacturing defects both in materials and workmanship in•
normal service for the period mentioned above.
Normal wear & tear on consumable items and their routine maintenance or replacement are not
warrantable items.
Engine units are covered independently by their respective manufacturer warranties.
OWNERS WARRANTY RESPONSIBILITIES
As the owner of an Entec Industries Ltd machine you are responsible for the following:
Operation of the machine in accordance with the Entec Industries Ltd instruction manual.•
Performance of the required maintenance listed in your Entec Industries Ltd instruction manual.•
In the event of a failure the Entec Industries Ltd authorised Timberwolf dealer is to be notified•
within 10 days of failure and the equipment is to be made available for inspection by the dealer
technician.
WARRANTY RESTRICTIONS
The Entec Industries Ltd warranty is restricted to the first end user only and is not transferable except
when an authorised Timberwolf dealer has a wood chipper registered with Entec Industries Ltd as a hire
chipper or long term demonstrator – in these situations they are duly authorised to transfer any remaining
warranty period to their first end user.
The Entec Industries Ltd warranty may be invalidated if any of the following apply:
The failed parts or assembly is interfered with in any way.•
Normal maintenance has not been performed.•
Incorrect reassembly of components.•
The machine has undergone modifications not approved in writing by Entec Industries Ltd.•
In the case of tractor driven equipment, use has been on an unapproved tractor.•
Conditions of use can be deemed abnormal.•
The machine has been used to perform tasks contrary to those stated in the Entec Industries Ltd•
instruction manual.
WARRANTY SERVICE
To obtain warranty service please contact your nearest Entec Industries Ltd approved Timberwolf dealer.
To obtain details of the nearest facility please contact Entec Industries Ltd at the address on the back of
this manual. These warranty terms are in addition to and not in substitution for and do not affect any right
and remedies which an owner might have under statute or at common law against the seller of the goods
under the contract by which the owner acquired the goods.

TIMBERWOLF
TW PTO 100G
16
(QYLURQPHQWDO 0DQXIDFWXULQJ //3 ,QFRUS FHUW
(QYLURQPHQWDO
(QYLURQPHQWDO
(QYLURQPHQWDO
(QYLURQPHQWDO 0DQXIDFWXULQJ
0DQXIDFWXULQJ
0DQXIDFWXULQJ
0DQXIDFWXULQJ //3
//3
//3
//3
(QWHF
(QWHF
(QWHF
(QWHF +RXVH
+RXVH
+RXVH
+RXVH
7RPR
7RPR
7RPR
7RPR ,QGXVWULDO
,QGXVWULDO
,QGXVWULDO
,QGXVWULDO (VWDWH
(VWDWH
(VWDWH
(VWDWH
6WRZPDUNHW
6WRZPDUNHW
6WRZPDUNHW
6WRZPDUNHW
6XIIRON
6XIIRON
6XIIRON
6XIIRON ,3
,3
,3
,3 $<
$<
$<
$<
7HO
7HO
7HO
7HO 


 


 )D[
)D[
)D[
)D[ 


 



(
(
(
(&
&
&
&'HFODUDWLRQ
'HFODUDWLRQ
'HFODUDWLRQ
'HFODUDWLRQ RI
RI
RI
RI ,QFRUSRUDWLRQ
,QFRUSRUDWLRQ
,QFRUSRUDWLRQ
,QFRUSRUDWLRQ
(QYLURQPHQWDO
(QYLURQPHQWDO
(QYLURQPHQWDO
(QYLURQPHQWDO 0DQXIDFWXULQJ
0DQXIDFWXULQJ
0DQXIDFWXULQJ
0DQXIDFWXULQJ //3
//3
//3
//3 D
D
D
DV
V
V
VWKH
WKH
WKH
WKH GHVLJQHU
GHVLJQHU
GHVLJQHU
GHVLJQHU DQG
DQG
DQG
DQG PDQXIDFWXUHU
PDQXIDFWXUHU
PDQXIDFWXUHU
PDQXIDFWXUHU FHUWLILHV
FHUWLILHV
FHUWLILHV
FHUWLILHV WKDW
WKDW
WKDW
WKDW WKH
WKH
WKH
WKH PDFKLQH
PDFKLQH
PDFKLQH
PDFKLQH
VWLSXODWHG
VWLSXODWHG
VWLSXODWHG
VWLSXODWHG EHORZ
EHORZ
EHORZ
EHORZ FRPSOLHV
FRPSOLHV
FRPSOLHV
FRPSOLHV ZLWK
ZLWK
ZLWK
ZLWK DOO
DOO
DOO
DOO WKH
WKH
WKH
WKH UHOHYDQW
UHOHYDQW
UHOHYDQW
UHOHYDQW SURYLVLRQV
SURYLVLRQV
SURYLVLRQV
SURYLVLRQV RI
RI
RI
RI WKH
WKH
WKH
WKH
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ 'LUHFWLYH
'LUHFWLYH
'LUHFWLYH
'LUHFWLYH (&
(&
(&
(&
 RWKHU UHOHYDQW GLUHFWLYHV
DQG
DQG
DQG
DQG WKH
WKH
WKH
WKH 1DWLRQDO
1DWLRQDO
1DWLRQDO
1DWLRQDO /DZV
/DZV
/DZV
/DZV DQG
DQG
DQG
DQG 5HJXODWLRQV
5HJXODWLRQV
5HJXODWLRQV
5HJXODWLRQV DGRSWLQJ
DGRSWLQJ
DGRSWLQJ
DGRSWLQJ WKHVH
WKHVH
WKHVH
WKHVH GLUHFWLYHV
GLUHFWLYHV
GLUHFWLYHV
GLUHFWLYHV
'HVLJQHU0DQXIDFWXUHU
'HVLJQHU0DQXIDFWXUHU
'HVLJQHU0DQXIDFWXUHU
'HVLJQHU0DQXIDFWXUHU 


(QYLURQPHQWDO 0DQXIDFWXULQJ //3
'HVFULSWLRQ
'HVFULSWLRQ
'HVFULSWLRQ
'HVFULSWLRQ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ 


8QSRZHUHG SRUWDEOH PDFKLQHU\ GHVLJQHG WR EH
LQFRUSRUDWHG LQWR D VXLWDEOH 372 SRZHU VRXUFH DQG
FKLS XS WUHH ZDVWH SULRU WR GLVSRVDO
0RGHO
0RGHO
0RGHO
0RGHO 


7: 372 *
6HULDO
6HULDO
6HULDO
6HULDO 1R
1R
1R
1R 6HULDO 0DQXIDFWXUH
%6,
%6,
%6,
%6, 7UDQVSRVHG
7UDQVSRVHG
7UDQVSRVHG
7UDQVSRVHG +DUPRQLVHG
+DUPRQLVHG
+DUPRQLVHG
+DUPRQLVHG 6WDQGDUGV
6WDQGDUGV
6WDQGDUGV
6WDQGDUGV DSSOLHG
DSSOLHG
DSSOLHG
DSSOLHG LQFOXGLQJ
LQFOXGLQJ
LQFOXGLQJ
LQFOXGLQJ SDUWVFODXVHV
SDUWVFODXVHV
SDUWVFODXVHV
SDUWVFODXVHV RI
RI
RI
RI
%6
%6
%6
%6 (1
(1
(1
(1 


 





 6DIHW\
6DIHW\
6DIHW\
6DIHW\ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ %DVLF
%DVLF
%DVLF
%DVLF FRQFHSWV
FRQFHSWV
FRQFHSWV
FRQFHSWV %6
%6
%6
%6 (1
(1
(1
(1 


 


 6DIHW\
6DIHW\
6DIHW\
6DIHW\ RI
RI
RI
RI 0DFKLQHU\6DIHW\
0DFKLQHU\6DIHW\
0DFKLQHU\6DIHW\
0DFKLQHU\6DIHW\
GLVWDQFHV
GLVWDQFHV
GLVWDQFHV
GLVWDQFHV WR
WR
WR
WR GDQJHU
GDQJHU
GDQJHU
GDQJHU ]RQHV
]RQHV
]RQHV
]RQHV %6
%6
%6
%6 (1
(1
(1
(1 


 


 $
$
$
$ 


 6DIH
6DIH
6DIH
6DIH HOHFWULFDO
HOHFWULFDO
HOHFWULFDO
HOHFWULFDO SUDFWLFHV
SUDFWLFHV
SUDFWLFHV
SUDFWLFHV %6
%6
%6
%6 (1
(1
(1
(1 






6DIHW\
6DIHW\
6DIHW\
6DIHW\ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ ±
±
±
±7HPSHUDWXUHV
7HPSHUDWXUHV
7HPSHUDWXUHV
7HPSHUDWXUHV RI
RI
RI
RI WRXFKDEOH
WRXFKDEOH
WRXFKDEOH
WRXFKDEOH VXUIDFHV
VXUIDFHV
VXUIDFHV
VXUIDFHV %6
%6
%6
%6 (1
(1
(1
(1 


 


 ±
±
±
±6DIHW\
6DIHW\
6DIHW\
6DIHW\ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ ±
±
±
±
6DIHW\
6DIHW\
6DIHW\
6DIHW\ UHODWHG
UHODWHG
UHODWHG
UHODWHG SDUWV
SDUWV
SDUWV
SDUWV RI
RI
RI
RI FRQWURO
FRQWURO
FRQWURO
FRQWURO V\VWHPV
V\VWHPV
V\VWHPV
V\VWHPV %6
%6
%6
%6 VDIHW\
VDIHW\
VDIHW\
VDIHW\ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ (PHUJHQF\
(PHUJHQF\
(PHUJHQF\
(PHUJHQF\ VWRS
VWRS
VWRS
VWRS %6
%6
%6
%6 (1
(1
(1
(1 


 






$
$
$
$ 


 ±
±
±
±6DIHW\
6DIHW\
6DIHW\
6DIHW\ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ ±
±
±
±+\GUDXOLFV
+\GUDXOLFV
+\GUDXOLFV
+\GUDXOLFV %6
%6
%6
%6 (1
(1
(1
(1 


 


 


$
$
$
$ 


 ±
±
±
±6DIHW\
6DIHW\
6DIHW\
6DIHW\ RI
RI
RI
RI 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ ±
±
±
±
,QWHUORFNLQJ
,QWHUORFNLQJ
,QWHUORFNLQJ
,QWHUORFNLQJ GHYLFHV
GHYLFHV
GHYLFHV
GHYLFHV %6
%6
%6
%6 (1
(1
(1
(1 


 


 


$
$
$
$ 


 ±
±
±
±)RUHVWU\
)RUHVWU\
)RUHVWU\
)RUHVWU\ 0DFKLQHU\
0DFKLQHU\
0DFKLQHU\
0DFKLQHU\ ±
±
±
±:RRG
:RRG
:RRG
:RRG FKLSSHUV
FKLSSHUV
FKLSSHUV
FKLSSHUV ±
±
±
±6DIHW\
6DIHW\
6DIHW\
6DIHW\ %6
%6
%6
%6 (1
(1
(1
(1
$
$
$
$
³
³
³
³5HVSRQVLEOH
5HVSRQVLEOH
5HVSRQVLEOH
5HVSRQVLEOH´
´
´
´3HUVRQ
3HUVRQ
3HUVRQ
3HUVRQ HPSRZHUHG
HPSRZHUHG
HPSRZHUHG
HPSRZHUHG WR
WR
WR
WR VLJQ
VLJQ
VLJQ
VLJQ BBBBBBBBBBBBBBBBBBBBBBBBBB0U
BBBBBBBBBBBBBBBBBBBBBBBBBB0U
BBBBBBBBBBBBBBBBBBBBBBBBBB0U
BBBBBBBBBBBBBBBBBBBBBBBBBB0U -HII
-HII
-HII
-HII +DLQHV
+DLQHV
+DLQHV
+DLQHV
3RVLWLRQ
3RVLWLRQ
3RVLWLRQ
3RVLWLRQ LQ
LQ
LQ
LQ &RPSDQ\
&RPSDQ\
&RPSDQ\
&RPSDQ\ 7HFKQLFDO
7HFKQLFDO
7HFKQLFDO
7HFKQLFDO 'LUHFWRU
'LUHFWRU
'LUHFWRU
'LUHFWRU
'DWH
'DWH
'DWH
'DWH 


 -XO\
-XO\
-XO\
-XO\ 



CERTIFICATE OF CONFORMITY

TIMBERWOLF
TW PTO 100G
17
EXAMPLE
IDENTIFICATION PLATE