Timberwolf Economizer 2100 User manual

1
W415-0842 / B / 03.08.10
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
INSTALLATION AND
OPERATING INSTRUCTIONS
1.14A
Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /
103 Miller Drive, Crittenden, Kentucky, USA, 41030
Phone [phone] • Fax [phone] • www.timberwolffireplaces.com • ask@timberwolffireplaces.com
SAFETY INFORMATION
!WARNING
If the information in these instructions is not followed exactly,
a fire or explosion may result causing property damage,
personal injury or death. Improper installation, adjustment,
alteration, service or maintenance can cause injury or property
damage, bodily injury or even death. Please read entire
manual before you install and use your appliance.
- This appliance can be very hot when burning.
- Combustible materials such as firewood, wet clothing, etc. placed too
close can catch fire.
- Children and pets must be kept from touching the appliance when it
is hot.
- The chimney must be sound and free of cracks. Before installing
this unit, contact the local building or fire authority and follow their
guidelines.
- Operate only with the door tightly closed.
- Burn wood behind the log retainer directly on the firebricks.
- Do not use an elevated grate or otherwise raise the fire.
- At least 14 square inches of outside air must be admitted to the room
or directly to the unit through a 4” diameter pipe.
- This appliance is designed to burn natural wood only. Higher
efficiencies and lower emissions generally result when burning air
dried seasoned hardwoods, as compared to softwoods or to green or
freshly cut hardwoods.
- Do not start a fire with chemicals or fluids such as gasoline, engine
oil, etc.
- Do not burn treated wood, coal, charcoal, coloured paper, cardboard,
solvents or garbage.
- Do not let the appliance become hot enough for any part to glow red.
- KEEP THE STOVE TOP TEMPERATURE BELOW 700°F (371°C).
Attempts to achieve heat output rates that exceed design
specifications can result in steel distortion and damage.
$10.00
CERTIFIED UNDER U.S. ENVIRONMENTAL PROTECTION AGENCY (E.P.A.) JULY 1990 40 C.F. R. PART 60 AND THE OREGON DEPARTMENT OF
ENVIRONMENTAL QUALITY (D.E.Q.) PARTICULATE EMISSION STANDARDS BY E.E.M.C THESE STOVES HAVE BEEN TESTED AND LISTED BY OMNI
TESTING SERVICES TO STANDARDS: CSA B366.2, ULC S627, UL 1482.
2100 & 2200
LEG MODELS &
PEDESTAL MODELS
2100 LEG MODEL
ILLUSTRATED

2
W415-0842 / B / 03.08.10
NOTE: Changes, other than editorial, are denoted by a vertical line in the margin.
TABLE OF CONTENTS
1.0 INSTALLATION OVERVIEW 3
2.0 INTRODUCTION 4
2.1 DIMENSIONS 5
2.2 SPECIFICATIONS 5
2.3 GENERAL INSTRUCTIONS 6
2.4 GENERAL INFORMATION 7
2.5 RATING PLATE INFORMATION 8
3.0 INSTALLATION PLANNING 9
3.1 APPLIANCE PLACEMENT 9
3.2 MINIMUM CLEARANCE TO COMBUSTIBLES 9
3.3 ALCOVE INSTALLATION 9
3.4 FLOOR PROTECTION 10
3.5 OUTSIDE AIR 10
4.0 INSTALLATION 11
4.1 CHIMNEY 12
4.1.1 CHIMNEY CONNECTION 13
4.1.2 ADDING SECTIONS 14
4.1.3 TYPICAL THROUGH THE CEILING 15
4.1.4 TYPICAL THROUGH THE WALL 16
4.1.5 TYPICAL EXISTING MASONRY 17
5.0 FINISHING 18
5.1 LEG INSTALLATION 18
5.2 PEDESTAL INSTALLATION 19
5.3 SECONDARY AIR TUBES 19
5.4 BRICK AND BAFFLE INSTALLATION 20
5.5 DOOR HANDLE INSTALLATION 21
5.6 ASH LIP INSTALLATION 21
6.0 OPTIONAL INSTALLATION 22
6.1 BLOWER KIT INSTALLATION 22
6.2 ASH DRAWER KIT (EP20LAD) 23
6.3 ASH PAN KIT (EP20PAD) 24
7.0 OPERATION 25
7.1 AIR CONTROL 26
7.2 FIRE EXTINGUISHERS / SMOKE DETECTORS 26
7.3 FUEL 26
7.4 LIGHTING A FIRE 27
7.4.1 FLASH FIRE 27
7.4.2 EXTENDED FIRE 27
7.5 SMOKING 27
8.0 MAINTENANCE 28
8.1 ASH REMOVAL PROCEDURES 28
8.2 ASH REMOVAL WITH ASH DRAWER 28
8.3 CREOSOTE FORMATION AND REMOVAL 29
8.4 RUNAWAY OR CHIMNEY FIRE 29
8.5 CHIMNEY CLEANING 29
8.6 CARE OF GLASS 30
8.7 DOOR REMOVAL 30
8.8 GLASS REPLACEMENT 31
8.9 GASKET REPLACEMENT 31
8.10 WOOD 32
9.0 REPLACEMENTS 33
10.0 TROUBLE SHOOTING 35
11.0 WARRANTY 36
12.0 SERVICE HISTORY 37
13.0 NOTES 38

3
W415-0842 / B / 03.08.10
1.0 INSTALLATION OVERVIEW
Venting, see “INSTALLATION -
CHIMNEY” section
Heat shield, see “LEG
INSTALLATION” section
See “AIR CONTROL”
section
Ash Drawer, see “OPTIONAL ASH
DRAWER KIT (EP20LAD)” section
for the leg model and “OPTIONAL
ASH PAN KIT (EP20PAD)” section
for the pedestal model.
Blower, see
“OPTIONAL BLOWER
INSTALLATION”
section
Handle, see “DOOR
HANDLE INSTALLATION”
section

4
W415-0842 / B / 03.08.10
2.0 INTRODUCTION
3.17A
!
WARNING
• THIS APPLIANCE IS HOT WHEN OPERATED AND CAN CAUSE SEVERE BURNS IF CONTACTED.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate
appliance according to operating instructions could cause fire or injury.
• Before installing this appliance, contact the local building or fire authority and follow their guidelines.
• This appliance must be installed by a qualified installer.
• Risk of burns. The appliance should be turned off and cooled before servicing.
• Do not let the appliance become hot enough for any part to glow red.
• Do not install damaged, incomplete or substitute components.
• Risk of cuts and abrasions. Wear protective gloves and safety glasses during installation. Sheet metal
edges may be sharp.
• Young children should be carefully supervised when they are in the same room as the appliance. Tod-
dlers, young children and others may be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the house. To restrict access to an appliance or stove,
install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the
room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance. Objects placed in
front of the appliance must be kept a minimum of 48” away from the front face of the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and
draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot
surfaces.
• Even after the appliance is out, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children
from hot surfaces. These screens and guards must be fastened to the floor.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• Under no circumstances should this appliance be modified.
• Do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass
should be done by a licensed or qualified service person.
• Do not strike or slam shut the appliance glass door.
• Operate only with the doors tightly closed.
• Only doors / optional fronts certified with the unit are to be installed on the appliance.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As
with all plastic bags, these are not toys and should be kept away from children and infants.
• If the appliance is not properly installed, a house fire may result. Do not expose the appliance to the elements
(ex. rain, etc.) and keep the appliance dry at all times. Wet insulation will produce an odour when the appliance
is used.
• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as re-
quired.
• Do not start a fire with chemicals or fluids such as gasoline, engine oil, etc.
• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to
smoke spillage in your home.
• Higher efficiencies and lower emissions generally result when burning air dried seasoned hardwoods,
as compared to softwoods or too green or freshly cut hardwoods. Burning wet unseasoned wood can
cause excessive creosote accumulation. When this is ignited it can cause a chimney fire that may result
in a serious house fire.
• This appliance is designed to burn natural wood only. Do not burn treated wood, coal, charcoal, co-
loured paper, cardboard, solvents or garbage.
• Burn wood behind the log retainer directly on the firebricks. Do not elevate grate or otherwise raise the
fire.
• Do not store wood within appliance installation clearances or within the space required for re-fueling
and ash removal.

5
W415-0842 / B / 03.08.10
2.1 DIMENSIONS
2.2 SPECIFICATIONS
Specifications 2100 2200
WIDTH 26” 26”
DEPTH 21 5/8” 24 5/8”
FLUE CENTER LINE TO REAR 6 1/2” 6 1/2”
FLUE CENTER LINE TO SIDE 13” 13”
HEIGHT PEDESTAL MODEL 29 7/8” 29 7/8”
HEIGHT LEG MODEL 31 5/8” 31 5/8”
CHAMBER (D.W.H) 11 5/8 x 20 7/8 x 11 5/8 14 5/8 x 20 7/8 x 11 5/8
CAPACITY 1.5 cubic feet 1.9 cubic feet
APPROX. AREA HEATED* 600-1800 square feet 800-1800 square feet
HEAT OUTPUT (HIGH BURN) ** 45,000 BTU 60, 000 BTU
DURATION LOW FIRE* 6 hours 8 hours
WEIGHT w/o BRICKS 180 lbs 210 lbs
WEIGHT OF BRICKS 47 lbs 60 lbs
IDEAL WOOD LENGTH 16” 16”
* Figures will vary considerably with individual conditions.
** Wolf Steel Ltd. estimated realistic BTU/h with hardwood logs and regular refueling.
6 1/2”
26”
31 5/8”
13”
21 5/8”
19 3/4” O 6”
26”
31 5/8”
24 5/8”
22 3/4”
O 6”
13”
6 1/2”
2100
2200

6
W415-0842 / B / 03.08.10
ALL WIRING SHOULD BE DONE BY A QUALIFIED ELECTRICIAN AND SHALL BE IN COMPLIANCE
WITH LOCAL CODES. IN THE ABSENCE OF LOCAL CODES, USE THE CURRENT CSA C22.1
CANADIAN ELECTRIC CODE (IN CANADA) OR THE ANSI/NFPA NO. 70 NATIONAL ELECTRIC CODE
IN THE UNITED STATES.
BURNING YOUR APPLIANCE WITH THE ASH WELL OPEN OR THE ASH DOOR AJAR CREATES A
FIRE HAZARD AND MAY CAUSE INTERNAL DAMAGE TO THE APPLIANCE OR A HOUSE AND/OR
CHIMNEY FIRE.
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE. DO
NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
PROVIDE ADEQUATE CLEARANCE FOR SERVICING AND OPERATING THE APPLIANCE.
PROVIDE ADEQUATE VENTILATION.
NEVER OBSTRUCT THE FRONT OPENING OF THE APPLIANCE.
OBJECTS PLACED IN FRONT OF THE APPLIANCE MUST BE KEPT A MINIMUM OF 48” FROM THE
FRONT FACE OF THE APPLIANCE.
DO NOT INSTALL IN A MOBILE HOME.
!
WARNING
2.3 GENERAL INSTRUCTIONS
• Before beginning your installation, consult with your local building code agency or fire officials and
insurance representative to ensure compliance.
• Non-toxic smoke will be emitted during the paint curing process, to help dissipate the smoke open a
window near the appliance.
• Remove any dust or debris off the top of the appliance before firing the appliance as the paint will be-
come soft as the appliance heats up and will harden as the appliance cures. To cure the paint on your
appliance burn your appliance moderately hot during the first few fires.
• To keep the gasket from sticking to the appliance as the paint is curing, periodically open the door
every 5-10 minutes.
• For the first two weeks use generous amounts of fuel and burn the appliance with the damper wide
open for an hour as the appliance goes through a process of eliminating moisture in the steel and fire-
bricks. The initial heat output will be reduced while the moisture is being drawn from the appliance and
it will be necessary to build several hot fires to remove this moisture. DURING THIS PROCESS DO
NOT OVERFIRE THE APPLIANCE. REDUCE THE AMOUNT OF AIR COMING INTO THE APPLI-
ANCE IF THE APPLIANCE OR CHIMNEY BECOMES RED.

7
W415-0842 / B / 03.08.10
Both models 2100 and 2200 are similar in design and use the same burning
principles.
They were specifically designed over many months of research to meet the
1990 U.S.A. EPA particulate emission standards and have been extensively
tested in Canadian and American laboratories. This system is the most ef-
ficient, simple and trouble free we know and works as follows:
Secondary air from the rear hole travels up the back in the secondary air
housing to the manifold located at the top and shoots out laterally to oxidize
the gases below the smoke exit.
The lower combustion chamber is lined with high temperature firebricks on 2
sides, the back and across the bottom, with a layer of fibre baffles at the top to
maintain a high temperature in the combustion chamber so that gases mixing
with the preheated air from the secondary air manifold tube are easily ignited
and burned. The appliance sides and back are shielded to direct the heat
upwards and forwards into the room.
Be sure to provide sufficient combustion air. There are many other appliances in your home competing for air such
as: a kitchen range hood, forced air heating devices, clothes dryer or a bathroom exhaust fan.
After extended periods of non-operation such as following a vacation or a warm weather season, the appliance may
emit a slight odour for a few hours. This is caused by dust particles on the firebox burning off. Open a window to suf-
ficiently ventilate the room.
If outside air is utilized, you should never experience a shortage
of combustion air. If you choose not to utilize outside air and
experience draft or smoking problems, you may need to open a
door, a window or otherwise provide some method of supplying
combustion air to the appliance.
We suggest that our woodburning hearth
products be installed and serviced by
professionals who are certified in the U.S.
by the National Fireplace Institute
®
(NFI) as
NFI Woodburning Specialists or who are
certified in Canada by
Wood Energy Technical
Training (WETT).
www.nficertified.org
AIR INLET PATH
EXHAUST PATH
2100 ILLUSTRATED
2.4 GENERAL INFORMATION
DO NOT OPERATE THIS APPLIANCE WITHOUT THE LEGS OR PEDESTAL INSTALLED.
!
WARNING

8
W415-0842 / B / 03.08.10
2.5 RATING PLATE INFORMATION
U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to
comply with July 1992 Particulate Emission Standards
W385-0465
EPA 2100
LISTED SOLID FUEL BURNING SPACE HEATER /
POÊLE À COMBUSTIBLE SOLIDE HOMOLOGUÉ
TESTED TO: / TESTÉ SELON :
UL1482 / ULC S627 / CSA B366.2 (DEC 92)
MODEL / MODÈLE: 2100
REPORT NO. / NUMÉRO DE RAPPORT 415-S-02-2
POUR INSTALLATION ET UTILISATION CONFORMÉMENT AUX INSTRUCTIONS DE
WOLF STEEL LTÉE. RENSEIGNEZ-VOUS AUPRÈS DES AUTORITÉS LOCALES DU
BÂTIMENT OU DU
SERVICE DES INCENDIES AU SUJET DES RESTRICTIONS ET DES INSPECTIONS
D’INSTALLATION DANS VOTRE RÉGION.
HAUTEUR DE PLAFOND MINIMAL 7” (2,13mm).
PROLONGEMENT D’ÂTRE/PROTECTION DU PLANCHER COMBUSTIBLE: SI INSTALLÉ
SUR UN PLANCHER COMBUSTIBLE, L’APPAREIL DOIT ÊTRE PLACÉ SUR UNE
PLAQUE PROTECTRICE INCOMBUSTIBLE S’ÉTENDANT SUR 18” (455mm) À L’AVANT
ET 8” (205mm) À L’ARRIÈRE ET SUR LES CÔTÉS.
TYPE DE CHIMNÉE: CHEMINÉE RÉSIDENTIELLE DE 6" DE DIAMÈTRE (152 mm)
HOMOLOGUÉE (UL 103HT).
RACCORD DE CHEMINÉE: DIAMÈTRE DE 6” (152mm) D’ACIER DE CALIBRE 24 MINIMUM.
18” (455mm) DE DÉGAGEMENT MINIMAL ENTRE LE RACCORD HORIZONTAL ET LE
PLAFOND.
NE RIEN ENTREPOSER SOUS L’APPAREIL.
DES MÉTHODES SPÉCIALES SONT REQUISES LORSQUE UNE CHEMINÉE TRAVERSE
UN MUR OU UN PLAFOND. VOIR LES INSTRUCTIONS ET LES CODES DU BÂTIMENT.
NE PAS RACCORDER À LA CHEMINÉE D’UN AUTRE APPAREIL.
COMBUSTIBLE: POUR USAGE AVEC LE BOIS SEULEMENT. N’UTILISEZ PAS DE CHENET
OU NE SURÉLEVEZ PAS LE BOIS. PRÉPAREZ LE FEU DIRECTEMENT SUR L’ÂTRE.
AVERTISSEMENT: RISQUE D’ÉCHAPPEMENT DE FUMÉE. TENIR LA PORTE FERMÉE
LORSQUE LE POÊLE FONCTIONNE. REMPLACEZ LA VITRE PAR UNE VITRE EN
CÉRAMIQUE SEULEMENT.
NE SURCHAUFFEZ PAS L’APPAREIL. SI L’APPAREIL OU LES RACCORDS ROUGEOIENT,
L’APPAREIL SURCHAUFEE. INSPECTEZ ET NETTOYEZ LA CHEMINÉE FRÉQUEMMENT.
DANS CERTAINES CONDITIONS, DES DÉPÔTS DE CRÉOSOTE PEUVENT SE FORMER
RAPIDEMENT.
PATTES OPTIONNELLES : SI LES PATTES OPTIONNELLES SONT INSTALLÉES, ELLES
DOIVENT ÊTRE INSTALLÉES AVANT DE FAIRE FONCTIONNER L’APPAREIL.
SOUFFLERIE OPTIONNELLE: EP-62, 115V, 60HZ, 0,82A. TENEZ LE CORDON ÉLECTRIQUE
LOIN DE L’APPAREIL.
DANGER: RISQUE DE SECOUSSE ÉLECTRIQUE. DÉBRANCHEZ AVANT DE PROCÉDER À
L’ENTRETIEN.
2009
JAN/JANV
FEB/FEVR
MAR/MARS
2012
OCT/OCT
NOV/NOV
DEC/DEC
2010
APR/AVR
MAY/MAI
JUN/JUIN
MANUFACTURE DATE: / DATE DE FABRICATION:
2011
JUL/JUILL
AUG/AOUT
SEP/SEPT
INSTALLANDUSEONLYINACCORDANCE WITH WOLF STEEL LTD’S
INSTRUCTIONS. CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT
RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
MINIMUM CEILING HEIGHT: 7FT (2.13m)
HEARTH EXTENSION / COMBUSTIBLE FLOOR PROTECTION: IF
INSTALLED ON A COMBUSTIBLE FLOOR, UNIT MUST BE PLACED ON A
NON-COMBUSTIBLE FLOOR PROTECTOR EXTENDING 18” (455mm) IN
FRONT AND 8” (205mm) TO THE SIDESAND BACK.
CHIMNEY TYPE: MINIMUM 6” (152mm) DIAMETER LISTED (UL 103HT)
RESIDENTIAL CHIMNEY.
CHIMNEY CONNECTOR: 6” (152mm) DIAMETER MINIMUM 24 GAUGE
STEEL MINIMUM CLEARANCE FROM HORIZONTAL CONNECTOR AND
CEILING 18” (455mm).
DO NOT OBSTRUCT SPACE UNDER HEATER.
SPECIAL METHODS ARE REQUIRED WHEN PASSING A CHIMNEY
THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILDING
CODES.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING
ANOTHER APPLIANCE.
FUEL: FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE
OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH.
WARNING: RISK OF SMOKE SPILLAGE. OPERATE ONLY WITH DOOR
FULLY CLOSED.
REPLACE GLASS ONLY WITH CERAMIC GLASS.
DO NOT OVERFIRE. IF HEATER OR CHIMNEY CONNECTORS GLOW,
YOU ARE OVERFIRING. INSPECT AND CLEAN CHIMNEY FREQUENTLY.
UNDER CERTAIN CONDITIONS OF USE CREOSOTE BUILD-UP MAY OCCUR
RAPIDLY.
OPTIONAL LEGS: IF TO BE INSTALLED WITH OPTIONAL LEGS, LEGS
MUST BE INSTALLED PRIOR TO OPERATION.
OPTIONAL BLOWER KIT: EP-65, 115V, 60HZ, 0.82AMP. ROUTE CORD
AWAY FROM UNIT.
DANGER: RISK OF ELECTRICAL SHOCK. DISCONNECT POWER
BEFORE SERVICING UNIT.
BACK WALL
B
SIDE WALL
A
BACK WALL
C
SIDE WALL
DE
F
G
H
H
I
PARALLEL / PARALLÈLE CORNER / COIN ALCOVE / ALCÔVE FLOOR PROTECTION /
PROTECTION
DE PLANCHER
ALCOVE / ALCÔVE
NOTE: Minimum width 62”, Minimum depth 32”
FRONT / AVANT (I) SIDES / CÔTÉS (H) BACK / ARRIÈRE (G)
SIDEWALL (A) 19” 19”
BACKWALL (B) 17 1/2” 12 1/2”
CORNER (C) 11” 7”
BACKWALL (D) 12 1/2” 12 1/2”
CEILING (E) 42” 42”
CEILING (F) 72” 72”
CANADA 18” 8” 8”
USA 16” 8” 8”
FLOOR PROTECTION / PROTECTION DE PLANCHER
PARALLEL & CORNER /
PARALLÈLE & COIN
SINGLE WALL CONNECTOR /
TUYAU DE RACCORDEMENT À
PAROI SIMPLE
DOUBLE WALL CONNECTOR /
TUYAU DE RACCORDEMENT À
PAROI DOUBLE
CAUTION:
ATTENTION:
HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITUREAWAY. CONTACT MAY CAUSE
SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS.
QUAND L’APPAREIL FONCTIONNE, LA SURFACE DEVIENT CHAUDE.
NE PAS TOUCHER. TENIR LES ENFANTS, LES VÊTEMENTS ET LES
MEUBLES À L’ÉCAR. LE CONTACT PEUT CAUSER DES BRÛLURES À L
A PEAU. VOIR LA PLAQUE D’HOMOLOGATION ET LES INSTRUCTIONS.
MADE IN / FABRIQUÉ AU:
WOLF STEEL LTD. BARRIE, ONTARIO CANADA
24 NAPOLEON ROAD, BARRIE, ON, L4M 4Y8 CANADA
NAC GUANGZHOU P.R.C.
NO.69 HEFENG ROAD, GUANGZHOU,CHINA
For rating plate location, see
“INSTALLATION OVERVIEW”
section.

9
W415-0842 / B / 03.08.10
3.0 INSTALLATION PLANNING
Have an authorized dealer install the appliance. If you install the appliance yourself, have your dealer review
your installation plans and/or installation.
Draw out a detailed plan of the installation including dimensions and verify the dimensions with the require-
ments listed in this manual.
You may wish to adjust the appliance position slightly to ensure the vent does not intersect with a framing
member. Appliance must be positioned so that no combustibles are within, or can swing within (e.g. drapes,
doors), 48” of the front of the appliance.
If the appliance is placed in a location where the ceiling height is less than 7’ above the base of the appliance,
the installation must follow the requirements in the section “ALCOVE INSTALLATION”.
67.1
3.1 APPLIANCE PLACEMENT
3.2 MINIMUM CLEARANCE TO COMBUSTIBLES
BACK WALL
B
SIDE WALL
A
BACK WALL
C
SIDE WALL
F
D
E
E
PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR
SIDEWALL (A) 19” 19”
SIDEWALL TO FLUE (B) 28 7/8” 28 7/8”
BACKWALL (C) 17 1/2” 12 1/2”
BACKWALL TO FLUE (D) 21” 16”
CORNER (E) 11” 7”
CEILING (F) 84” 84”
Clearances can be reduced with shielding acceptable to local authorities. Reduced installation must comply
with NFPA 211 or CAN/CSA-B365.
ALCOVE
PARALLEL & CORNER SINGLE WALL CONNECTOR DOUBLE WALL CONNECTOR
CEILING (F) 72” 72”
NOTE: Minimum width 62”, Minimum depth 32”
DO NOT INSTALL INTO ANY AREA HAVING LESS THAN 7 FEET (CEILING TO APPLIANCE BOTTOM,
EXCLUDING HEARTH HEIGHT).
!
WARNING
19"
28 7/8"
ALCOVE
4 FOOT
MAX
16” 12 ½”
3.3 ALCOVE INSTALLATION
Your appliance may be installed, using a listed
double wall connector, such as Security DL6 in
Canada, the Simpson Duravent Plus DVL in the
USA or an equivalent double wall connector,
into an alcove having a depth of no more than 4
feet and a height of at least 7 feet. The minimum
clearances are as shown.
F

10
W415-0842 / B / 03.08.10
3.4 FLOOR PROTECTION
If the appliance is to be installed on top of a combustible floor, it must be placed on an approved non-combusti-
ble hearth pad, that extends 8” beyond the appliance sides and back and 18” to the front. The reduced clear-
ance from the back of the appliance may result in the appliance pad terminating shorter than 8” beyond the
appliance.
NOTE: Floor protection is required for spark and ash shielding, but not for limiting floor temperatures
from the radiant heat of the appliance. The appliance was designed and safety tested so that without
any protection, the floor would not overheat.
Refer to local building codes for suitable floor protection materials.
K
J
J
I
MINIMUM FLOOR PROTECTION
FRONT (I) SIDES (J) BACK (K)
CANADA 18” 8” 8”
USA 16” 8” 8”
NOTE: If a section of horizontal chimney connector is used, floor protection is
required under the chimney connector and 2” beyond each side.
3.5 OUTSIDE AIR
The following are signs that a fresh air kit may be required:
• When there is combustion present: Wood burns poorly, smoke spills, back-draft takes place and your
chimney does not draw steadily.
• In the winter there is too much condensation on the windows.
• Opening a window seems to alleviate the above symptoms.
• A ventilation system is installed in the house.
• Other devices are present that exhaust house air.
• The house has tight fitting windows and/or is equipped with a well-sealed vapour barrier.
!
WARNING
IF ROOM AIR STARVATION OCCURS BECAUSE THE FRESH AIR INTAKE IS BLOCKED WITH ICE,
LEAVES, ETC., OR BECAUSE THE APPLIANCE DOOR WAS LEFT OPEN, OR DUE TO A STRONG
EXHAUST FAN OPERATING ETC., DANGEROUS FUMES AND SMOKE FROM THE OPERATING APPLI-
ANCE COULD BE DRAWN INTO THE ROOM.

11
W415-0842 / B / 03.08.10
4.0 INSTALLATION
68.3
!
WARNING
WEAR GLOVES AND SAFETY GLASSES FOR PROTECTION.
CAREFULLY FOLLOW THE INSTRUCTIONS FOR ASSEMBLY OF THE PIPE AND OTHER PARTS
NEEDED TO INSTALL THE APPLIANCE. FAILURE TO DO SO MAY RESULT IN A FIRE, ESPECIALLY IF
COMBUSTIBLES ARE TOO CLOSE TO THE APPLIANCE OR CHIMNEY AND AIR SPACES ARE
BLOCKED, PREVENTING THE FREE MOVEMENT OF COOLING AIR.
DO NOT DRAW OUTSIDE AIR FROM GARAGE SPACES. EXHAUST PRODUCTS OF GASOLINE ENGINES ARE
HAZARDOUS.
DO NOT INSTALL OUTSIDE AIR DUCTS SUCH THAT THE AIR MAY BE DRAWN FROM ATTIC SPACES, BASEMENTS
OR ABOVE THE ROOFING WHERE OTHER HEATING APPLIANCES OR FANS AND CHIMNEYS EXHAUST OR UTILIZE
AIR. THESE PRECAUTIONS WILL REDUCE THE POSSIBILITY OF APPLIANCE SMOKING OR AIR FLOW REVERSAL.
THE OUTSIDE AIR INLET MUST REMAIN CLEAR OF LEAVES, DEBRIS ICE AND/OR SNOW. IT MUST BE UNRE-
STRICTED WHILE APPLIANCE IS IN USE TO PREVENT ROOM AIR STARVATION WHICH CAN CAUSE SMOKE SPILL-
AGE AND AN INABILITY TO MAINTAIN A FIRE. SMOKE SPILLAGE CAN ALSO SET OFF SMOKE ALARMS.
NEGATIVE PRESSURE WITHIN YOUR HOME MAY INADVERTENTLY AFFECT YOUR APPLIANCE.
TO PREVENT CONTACT WITH SAGGING OR LOOSE INSULATION, THE APPLIANCE MUST NOT BE INSTALLED
AGAINST VAPOUR BARRIERS OR EXPOSED INSULATION. LOCALIZED OVERHEATING COULD OCCUR AND A FIRE
COULD RESULT.
DO NOT USE MAKESHIFT COMPROMISES DURING INSTALLATION. DO NOT BLOCK OR RESTRICT AIR, GRILLE OR
LOUVRE OPENINGS. DO NOT ADD A HOOD.

12
W415-0842 / B / 03.08.10
NEVER INSTALL A SINGLE WALL SLIP SECTION OR SMOKE PIPE IN A CHASE STRUCTURE. THE HIGHER
TEMPERATURE OF THIS SINGLE WALL PIPE MAY RADIATE SUFFICIENT HEAT TO COMBUSTIBLE
CHASE MATERIALS TO CAUSE A FIRE.
DO NOT CONNECT THIS APPLIANCE TO A CHIMNEY SYSTEM SERVING ANOTHER APPLIANCE.
TO AVOID DANGER OF FIRE, ALL INSTRUCTIONS MUST BE STRICTLY FOLLOWED, INCLUDING THE
PROVISION OF AIR SPACE CLEARANCE BETWEEN CHIMNEY SYSTEM AND ENCLOSURE. TO
PROTECT AGAINST THE EFFECTS OF CORROSION ON THOSE PARTS EXPOSED TO THE WEATHER, WE
RECOMMEND THAT THE CHASE TOP BE PAINTED WITH A RUST-RESISTANT PAINT.
DO NOT FILL ANY FRAMED SPACE AROUND THE CHIMNEY WITH INSULATION OR ANY OTHER MATERIAL.
INSULATION PLACED IN THIS AREA COULD CAUSE ADJACENT COMBUSTIBLES TO OVERHEAT.
MAINTAIN A MINIMUM 2" AIR CLEARANCE TO ALL PARTS OF THE CHIMNEY SYSTEM AT ALL TIMES.
FAILURE TO MAINTAIN THIS 2" AIR CLEARANCE WILL CAUSE A STRUCTURE FIRE. NEVER FILL THIS
SPACE WITH ANY TYPE OF MATERIAL.
DETAILED INSTRUCTIONS FOR INSTALLATION OF THE CHASE TOP, STORM COLLAR AND
TERMINATION CAP ARE PACKAGED WITH THESE PARTS.
DO NOT CUT RAFTERS OR CEILING JOISTS WITHOUT FIRST CONSULTING A BUILDING OFFICIAL
TO ENSURE STRUCTURAL INTEGRITY IS NOT COMPROMISED.
FIRESTOP SPACERS MUST BE USED WHENEVER THE CHIMNEY PENETRATES A CEILING/FLOOR AREA.
THE TOTAL HORIZONTAL VENT LENGTH SHOULD NOT EXCEED 40% OF THE CHIMNEY HEIGHT
ABOVE THE STOVE. ALL HORIZONTAL SMOKE PIPE MUST SLOPE SLIGHTLY UPWARDS A MINIMUM
OF 1/4” PER FOOT AND ALL CONNECTIONS MUST BE TIGHT AND SECURED BY THREE SHEET
METAL SCREWS EQUALLY SPACED. AN UNINSULATED SMOKE PIPE SHALL NOT PASS THROUGH
AN ATTIC, ROOF SPACE, CLOSET OR SIMILAR CONCEALED SPACE, OR THROUGH A FLOOR,
CEILING, WALL OR PARTITION, OR ANY COMBUSTIBLE CONSTRUCTIONS.
DO NOT USE ANY MAKESHIFT MATERIALS DURING INSTALLATION.
!
WARNING
4.1 CHIMNEY
Your appliance may be connected to a factory built or masonry chimney. If you are using a factory built chim-
ney, it must comply with ULCS629 (Canada) or UL103 (USA) standards. It must therefore be a 6” HT Type
(2100°F) chimney. It is extremely important that it be installed according to the manufacturer’s specifications.
The manufacturer’s installation instructions and specified clearances should always be followed in accordance
with local and national codes. In Canada the CSA B365 and the CSA C22.1 installation codes are to be fol-
lowed. In the USA the ANSI NFPA 70 and ANSI NFPA 211 installation codes are to be followed.
Chimney and chimney connector must be in good condition and kept clean.

13
W415-0842 / B / 03.08.10
4.1.1 CHIMNEY CONNECTION
This appliance must be connected to:
A. A chimney complying with the requirements for Type
HT chimneys in the Standard for Chimneys, Factory-
Built, Residential Type and Building Heating Appli-
ance, or
B. A code-approved masonry chimney with a flue liner.
Vent the stove into a masonry chimney or an ap-
proved, insulated solid-fuel stainless-steel chimney
with as short and straight a length of 6” diameter
chimney connector as possible. Connection to a ma-
sonry chimney must be by a metal or masonry thimble
cemented in place.
TOWARD
APPLIANCE
FLUE GAS
DIRECTION
MALE END OF
CONNECTOR
OR CHIMNEY
PIPE
58.1A
Your chimney connector and chimney must have the same diameter as the appliance’s exhaust flue outlet. The
appliance pipe must be made of aluminized or cold roll steel with a minimum 24 gauge thickness. It is strictly
forbidden to use galvanized steel.
A 6” diameter single wall chimney connector, used to connect the appliance to the chimney, must be installed with
the crimped end toward the appliance. This will ensure that the moisture which condenses from the burning wood
will flow back into the fire chamber. Each joint in the chimney connector must be secured with at least three sheet
metal screws.
For installation of your chimney connector, the following recommendations may be useful.
• The chimney connector must be short and straight. For optimum performance it is recommended that
all horizontal runs have a minimum 1/4” rise per foot, with the upper end of the section toward the
chimney. For safe and proper operation of the appliance, see “INSTALLATION” instructions.
• To insure a good draft, the total horizontal length of the connector should never exceed 8’ to 10’. In
the case of vertical installation, the total length of the connector can be longer and connected without
problem to the chimney at the ceiling level.
• There should never be more than two 90° elbows in the entire connector and chimney system. Never
start with a 90° elbow. Always go up vertically for at least 2 feet from the flue collar before using a 90°
elbow.
• The connector must not pass through any combustible material, nor may it pass through a concealed
space (such as an attic, roof space, or closet). If passing through a wall, ceiling, or into a masonry
chimney, use either chimney components listed for that specific use, or means acceptable to local
authorities having jurisdiction over the installation.

14
W415-0842 / B / 03.08.10
4.1.2 ADDING SECTIONS
A
dd chimney sections, according to the manufacturers installation instructions. The chimney must extend at
least, 3 feet above its point of contact with the roof and at least 2 feet higher than any wall, roof or building
within 10 feet horizontally.
59.1A
3 FT
MIN
3 FT
MIN
3 FT
MIN
3 FT
MIN
10 FT OR
MORE
LESS THAN
10 FT
FLAT ROOF WALL
2 FT
MIN
10 FT TO
NEAREST
ROOFLINE
RIDGE
LESS THAN
10 FEET
2 FT MIN 2 FT
MIN
An insulated stainless steel chimney must be supported at the ceiling or roof and its installation must comply
with its manufacturer’s instructions.

15
W415-0842 / B / 03.08.10
4.1.3 TYPICAL THROUGH THE CEILING
A. Move the stove into position with the flue centered, midpoint between two
joists to prevent having to cut them. Use a plumb bob to line up the center.
B. Cut and frame an opening in the ceiling to provide a 2” clearance between
the outside of the chimney and any combustible material. DO NOT FILL THIS
SPACE WITH ANY TYPE OF MATERIAL.
Nail headers between the joist for extra support.
Firestop spacers must be placed on the bot-
tom of each framed opening in any floor or
ceiling that the chimney passes through.
If your chimney system is enclosed within
the attic area, a rafter radiation shield is
required.
C. Hold a plumb bob from the underside of
the roof to determine where the opening in
the roof should be. Cut and frame the roof
opening to maintain proper 2” clearances.
NOTE: The chimney must be supported at the ceiling or roof so that it’s
weight does not rest on the appliance and must comply with it’s
manufacturer’s instructions.
60.1A
HEADERS
FIRESTOP SPACER -
UNDERSIDE OF JOIST
FLOOR
PROTECTOR
ROOF
FLASHING
STORM
COLLAR
TERMINAL
COMBUSTIBLE
WALL
MAINTAIN 2”
CLEARANCE
CHIMNEY
CONNECTOR
CHIMNEY
SUPPORT
LISTED CHIMNEY INSULATION
CEILING
SUPPORT
LISTED
CHIMNEY
SPECIFIED
CLEARANCE
TO STOVE
CONNECTION
DETAIL

16
W415-0842 / B / 03.08.10
4.1.4 TYPICAL THROUGH THE WALL
If possible, design the installation so that the connector does not pass through a combustible wall. If during
your installation you must pass through a combustible wall, check with your building inspector before you be-
gin. Also check with the chimney connector manufacturer for any specific requirements.
Consult with your dealer regarding special connection components available for use for wall pass-throughs.
Use only parts that have been tested and listed for use in a wall pass-through.
61.1
FLOOR
PROTECTOR
ROOF
FLASHING
STORM
COLLAR
TERMINAL
COMBUSTIBLE
WALL
CHIMNEY
CONNECTOR
MAINTAIN 2”
CLEARANCE
THROUGH EAVE
COMBUSTIBLE
CEILING
LISTED
CHIMNEY
COMBUSTIBLE
OUTSIDE WALL
TO
STOVE
2”
CLEARANCE
INSULATED
“T”
WALL
SUPPORT
WALL SPACER
FOR OUTSIDE
WALL
CONNECTION
DETAIL
SECTION
LISTED
CHIMNEY PIPE
THIMBLE

17
W415-0842 / B / 03.08.10
4.1.5 TYPICAL EXISTING MASONRY
You can also install your appliance using your
existing masonry chimney. To do so, follow the
guidelines below. You may want to use a factory-
built thimble, or construct your own brick thimble.
If you are using a masonry chimney, it is
important that it be built in compliance with
the specifications of the Building Code in
your region. It must normally be lined with
fire clay bricks, metal or clay tiles sealed
together with fire cement. (Round flues are
the most efficient). The maximum flue size
is 8” x 8” square or 6” round.
62.1
FLOOR
PROTECTOR
CHIMNEY
CONNECTOR
COMBUSTIBLE
WALL
CLEARANCE
EAVE
RAFTER
CLEARANCE WITH FIRESTOP
CEILING JOIST
THIMBLE

18
W415-0842 / B / 03.08.10
5.0 FINISHING
5.1 LEG INSTALLATION
To avoid being damaged during shipping, the appliance
has been bolted to the pallet and must be unbolted before
the appliance can be installed.
NOTE: If installing the optional ash drawer, see “OP-
TIONAL ASH DRAWER KIT (EP20LAD)” section prior
heat shield and leg installation.
NOTE: Legs may need to be adjusted in order to
properly align with the heat shield holes.
5.1.1 With the bolt through the legs, feed the washer and
lock washer onto the bolt. Thread the nut a thread
or two onto the bolt and slide the leg onto the slot on
appliance as illustrated. NOTE: Bolts must be tight
prior to heat shield installation.
5.1.2 Slide the heat shield over the four bolts. Finally, secure
the heat shield in place using the remaining nuts.
5.1.3 Lift the appliance up and gently set down on all four
legs. Do not pivot appliance up on its legs, as this could
result in damage to the legs.
For additional logo placement locations, see “OPTIONAL ASH DRAWER”
section.
!
WARNING
KNOCKOUT NOT TO BE REMOVED EXCEPT WHEN INSTALLING THE OPTIONAL ASH DRAWER KIT.
LOGO
PLACEMENT
KNOCKOUT
(SEE WARNING
ABOVE)

19
W415-0842 / B / 03.08.10
5.2 PEDESTAL INSTALLATION
PEDESTAL
LOGO PLACEMENT
NOTE: If an optional ash drawer kit is to be in-
stalled, ensure open side of pedestal is at the front
of the appliance. If not, opening should be at the
back.
To avoid being damaged during shipping, the appliance
has been bolted to the pallet and must be unbolted
before the appliance can be installed.
5.2.1 Using the machine screws supplied, secure the
pedestal to the four brackets on the bottom of
the firebox.
5.2.2 Lift the appliance up and gently set down on
pedestal. Do not pivot appliance up as it could
result in damage to the pedestal.
AL
5.3 SECONDARY AIR TUBES
A
B
2100
ILLUSTRATED
2200
ILLUSTRATED
C
B
COTTER PIN
TUBE
RETAINER
C
A
HOLE
5.3.1 Start at the back work-
ing forwards by sliding
the secondary air tube in
the firebox and inserting
the tube into the hole,
as illustrated in “A”.
5.3.2 Slide the tube into the
opposite hole. With the
holes on the secondary
air tube pointing for-
ward, align the tube with
the tube retainer and
insert the cotter pin, as
illustrated in “B”.
5.3.3 Spread the cotter pin to
retain.
NOTE: On the 2200 model
there are 4 secondary air
tubes. One of the tubes has
larger holes. This tube is to be
located closest to the front of
the appliance, as illustrated in
“C”.

20
W415-0842 / B / 03.08.10
5.4 BRICK AND BAFFLE INSTALLATION
2100 2200
A
A
A
A
A
A
A
A
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
A
C
C
D
D
D
D
D
E
F
F
F
F
OPERATION OF THE APPLIANCE WITHOUT THE BAFFLES CAN RESULT IN EXCESSIVE TEMPERA-
TURES THAT COULD DAMAGE THE APPLIANCE, CHIMNEY AND THE SURROUNDING ENCLOSURE.
!
WARNING
With the appliance and chimney installation completed, move the bricks into place as illustrated below.
5.4.1 Install the (2100) four (A) bricks, two (B) bricks and two (C) bricks. Install the (2200) nine (A) bricks
and one (E) brick, working from the back of the appliance forward as illustrated. NOTE: Left and right
rear bricks have been cut (model 2100 only).
5.4.2 Install (2100) two (A) bricks or (2200) four (A) bricks along both sides of the appliance. Install the four
(A) bricks and one (D) brick along the back wall by pivoting the bricks up under the brick retainer.
NOTE: Place narrow brick in centre.
5.4.3 Carefully pivot fibre baffles (F) up onto the secondary air tubes as illustrated. Ensure that the top
baffles are pushed all the way to the rear of the firebox, leaving a minimum of a 1 inch gap along the
front. This will allow the flue gases to escape the firebox. Ensure overlap joint is tight.
5.4.4 Install the two (D) bricks along the front.
BAFFLE
SECONDARY
AIR TUBES
OVERLAP
JOINT
2100 ILLUSTRATED