Timeguard TS800B User manual

Important
This Timecontroller is recommended for
general domestic appliances up to 13 amp
resistive or 5 amp inductive rating. Certain
washing machines require the power to be
permanently connected and they cannot be
controlled by the TS800B. This is also true of
tumble dryers with push button start.
Note: Minimum setting interval =
15 minutes.
Minimum ON/OFF time between
settings = 30 minutes.
Specifications
Operating Temp: 0°C to 40°C
Operating Voltage: 230V AC 50Hz
Switch Rating: 230V AC 13 amp resistive
(3kW)
5 amp inductive
400W Filament Lighting
100W Low Energy or any
type of Fluorescent
Lighting
Conforms to
Directives: 73/23/EEC & 89/336/EEC
Not suitable for discharge lighting
(eg SON or Halide)
HELPLINE
020-8450-0515
or email [email protected]
For a product brochure please contact:
Timeguard Ltd.
Victory Park, 400 Edgware Road,
London NW2 6ND Tel: [phone]
or email [email protected]
A Group company
5 6
OPERATING INSTRUCTIONS
24 HOUR
PLUG-IN TIME
CONTROLLER
Cat. No TS800B
3 Year Guarantee
In the unlikely event of the product becoming faulty
due to defective material or manufacture within
3 years of the date of purchase, please return it to
your supplier in the first year with proof of purchase
and it will be replaced free of charge. During the
second and third years or any difficulty in the first
year telephone the helpline on 020 8450 0515
67-058-269
TS800B_Instrucs.indd 2TS800B_Instrucs.indd 2 14/1/08 10:47:0214/1/08 10:47:02

Self-
cancelling
override
switch
Time
indicator
Tough flame
retardant casing
Setting pins
Protective
lobes
24hr programme ring
(inner holes = ON
outer holes = OFF)
Front socket
face
TS800B 24 Hour Plug-In
Time Controller
1To programme the controller:-
aDecide what times you would like the
Timecontroller to switch on and off.
bInsert the setting pins into the
programme ring according to your
requirements. To switch ON insert the
pins into the inner circle of holes. To
switch OFF insert the pins into the outer
circle of holes.
Important
The pins should be pushed fully home or
they will catch on the underside of the
protective lobes on the bottom of the
front socket face (see diagram).
2Check your programme by manually
turning the programme ring clockwise
once through the 24 hour cycle.
Note: When the pins pass over the time
indicator it will require a firm hand.
3Turn the programme ring clockwise until
the correct time of day is directly above
the time indicator at the top of the front
socket face (see diagram).
4Plug the Timecontroller into a socket and
switch socket ON if necessary.
5Plug your appliance into the
Timecontroller and switch the appliance
ON.
6You can switch your appliance ON and
OFF at any time, by using the small lever
at the side of the Timecontroller
0=OFF, 1=ON. This will self cancel when
the next ON or OFF programme operates.
Points to note
aEach time the Timecontroller has carried
out an automatic switching operation the
manual switch cannot be operated for
about 15 minutes before and after
automatic switching because it is
mechanically locked for this period.
bIf required you can programme your
Timecontroller to switch off only by
inserting just a single pin. For many
electrical appliances you can, therefore,
programme for off only to ensure that if
you forget to switch the appliance off
nothing can be damaged or unnecessary
power used. When using this technique
switch on by hand using the self cancelling
override switch.
cThe Programme ring can be turned even
when the Timecontroller is operating. In
case of power failiure, please re-adjust the
Timecontroller to the correct time of day,
turning the dial in a clockwise direction.
1 2 3 4
TS800B_Instrucs.indd 1TS800B_Instrucs.indd 1 14/1/08 10:46:4314/1/08 10:46:43

Self-
cancelling
override
switch
Time
indicator
Tough flame
retardant casing
Setting pins
Protective
lobes
24hr programme ring
(inner holes = ON
outer holes = OFF)
Front socket
face
TS800B 24 Hour Plug-In
Time Controller
1To programme the controller:-
aDecide what times you would like the
Timecontroller to switch on and off.
bInsert the setting pins into the
programme ring according to your
requirements. To switch ON insert the
pins into the inner circle of holes. To
switch OFF insert the pins into the outer
circle of holes.
Important
The pins should be pushed fully home or
they will catch on the underside of the
protective lobes on the bottom of the
front socket face (see diagram).
2Check your programme by manually
turning the programme ring clockwise
once through the 24 hour cycle.
Note: When the pins pass over the time
indicator it will require a firm hand.
3Turn the programme ring clockwise until
the correct time of day is directly above
the time indicator at the top of the front
socket face (see diagram).
4Plug the Timecontroller into a socket and
switch socket ON if necessary.
5Plug your appliance into the
Timecontroller and switch the appliance
ON.
6You can switch your appliance ON and
OFF at any time, by using the small lever
at the side of the Timecontroller
0=OFF, 1=ON. This will self cancel when
the next ON or OFF programme operates.
Points to note
aEach time the Timecontroller has carried
out an automatic switching operation the
manual switch cannot be operated for
about 15 minutes before and after
automatic switching because it is
mechanically locked for this period.
bIf required you can programme your
Timecontroller to switch off only by
inserting just a single pin. For many
electrical appliances you can, therefore,
programme for off only to ensure that if
you forget to switch the appliance off
nothing can be damaged or unnecessary
power used. When using this technique
switch on by hand using the self cancelling
override switch.
cThe Programme ring can be turned even
when the Timecontroller is operating. In
case of power failiure, please re-adjust the
Timecontroller to the correct time of day,
turning the dial in a clockwise direction.
1 2 3 4
TS800B_Instrucs.indd 1TS800B_Instrucs.indd 1 14/1/08 10:46:4314/1/08 10:46:43

Self-
cancelling
override
switch
Time
indicator
Tough flame
retardant casing
Setting pins
Protective
lobes
24hr programme ring
(inner holes = ON
outer holes = OFF)
Front socket
face
TS800B 24 Hour Plug-In
Time Controller
1To programme the controller:-
aDecide what times you would like the
Timecontroller to switch on and off.
bInsert the setting pins into the
programme ring according to your
requirements. To switch ON insert the
pins into the inner circle of holes. To
switch OFF insert the pins into the outer
circle of holes.
Important
The pins should be pushed fully home or
they will catch on the underside of the
protective lobes on the bottom of the
front socket face (see diagram).
2Check your programme by manually
turning the programme ring clockwise
once through the 24 hour cycle.
Note: When the pins pass over the time
indicator it will require a firm hand.
3Turn the programme ring clockwise until
the correct time of day is directly above
the time indicator at the top of the front
socket face (see diagram).
4Plug the Timecontroller into a socket and
switch socket ON if necessary.
5Plug your appliance into the
Timecontroller and switch the appliance
ON.
6You can switch your appliance ON and
OFF at any time, by using the small lever
at the side of the Timecontroller
0=OFF, 1=ON. This will self cancel when
the next ON or OFF programme operates.
Points to note
aEach time the Timecontroller has carried
out an automatic switching operation the
manual switch cannot be operated for
about 15 minutes before and after
automatic switching because it is
mechanically locked for this period.
bIf required you can programme your
Timecontroller to switch off only by
inserting just a single pin. For many
electrical appliances you can, therefore,
programme for off only to ensure that if
you forget to switch the appliance off
nothing can be damaged or unnecessary
power used. When using this technique
switch on by hand using the self cancelling
override switch.
cThe Programme ring can be turned even
when the Timecontroller is operating. In
case of power failiure, please re-adjust the
Timecontroller to the correct time of day,
turning the dial in a clockwise direction.
1 2 3 4
TS800B_Instrucs.indd 1TS800B_Instrucs.indd 1 14/1/08 10:46:4314/1/08 10:46:43

Self-
cancelling
override
switch
Time
indicator
Tough flame
retardant casing
Setting pins
Protective
lobes
24hr programme ring
(inner holes = ON
outer holes = OFF)
Front socket
face
TS800B 24 Hour Plug-In
Time Controller
1To programme the controller:-
aDecide what times you would like the
Timecontroller to switch on and off.
bInsert the setting pins into the
programme ring according to your
requirements. To switch ON insert the
pins into the inner circle of holes. To
switch OFF insert the pins into the outer
circle of holes.
Important
The pins should be pushed fully home or
they will catch on the underside of the
protective lobes on the bottom of the
front socket face (see diagram).
2Check your programme by manually
turning the programme ring clockwise
once through the 24 hour cycle.
Note: When the pins pass over the time
indicator it will require a firm hand.
3Turn the programme ring clockwise until
the correct time of day is directly above
the time indicator at the top of the front
socket face (see diagram).
4Plug the Timecontroller into a socket and
switch socket ON if necessary.
5Plug your appliance into the
Timecontroller and switch the appliance
ON.
6You can switch your appliance ON and
OFF at any time, by using the small lever
at the side of the Timecontroller
0=OFF, 1=ON. This will self cancel when
the next ON or OFF programme operates.
Points to note
aEach time the Timecontroller has carried
out an automatic switching operation the
manual switch cannot be operated for
about 15 minutes before and after
automatic switching because it is
mechanically locked for this period.
bIf required you can programme your
Timecontroller to switch off only by
inserting just a single pin. For many
electrical appliances you can, therefore,
programme for off only to ensure that if
you forget to switch the appliance off
nothing can be damaged or unnecessary
power used. When using this technique
switch on by hand using the self cancelling
override switch.
cThe Programme ring can be turned even
when the Timecontroller is operating. In
case of power failiure, please re-adjust the
Timecontroller to the correct time of day,
turning the dial in a clockwise direction.
1 2 3 4
TS800B_Instrucs.indd 1TS800B_Instrucs.indd 1 14/1/08 10:46:4314/1/08 10:46:43

Important
This Timecontroller is recommended for
general domestic appliances up to 13 amp
resistive or 5 amp inductive rating. Certain
washing machines require the power to be
permanently connected and they cannot be
controlled by the TS800B. This is also true of
tumble dryers with push button start.
Note: Minimum setting interval =
15 minutes.
Minimum ON/OFF time between
settings = 30 minutes.
Specifications
Operating Temp: 0°C to 40°C
Operating Voltage: 230V AC 50Hz
Switch Rating: 230V AC 13 amp resistive
(3kW)
5 amp inductive
400W Filament Lighting
100W Low Energy or any
type of Fluorescent
Lighting
Conforms to
Directives: 73/23/EEC & 89/336/EEC
Not suitable for discharge lighting
(eg SON or Halide)
HELPLINE
020-8450-0515
or email [email protected]
For a product brochure please contact:
Timeguard Ltd.
Victory Park, 400 Edgware Road,
London NW2 6ND Tel: [phone]
or email [email protected]
A Group company
5 6
OPERATING INSTRUCTIONS
24 HOUR
PLUG-IN TIME
CONTROLLER
Cat. No TS800B
3 Year Guarantee
In the unlikely event of the product becoming faulty
due to defective material or manufacture within
3 years of the date of purchase, please return it to
your supplier in the first year with proof of purchase
and it will be replaced free of charge. During the
second and third years or any difficulty in the first
year telephone the helpline on 020 8450 0515
67-058-269
TS800B_Instrucs.indd 2TS800B_Instrucs.indd 2 14/1/08 10:47:0214/1/08 10:47:02

Important
This Timecontroller is recommended for
general domestic appliances up to 13 amp
resistive or 5 amp inductive rating. Certain
washing machines require the power to be
permanently connected and they cannot be
controlled by the TS800B. This is also true of
tumble dryers with push button start.
Note: Minimum setting interval =
15 minutes.
Minimum ON/OFF time between
settings = 30 minutes.
Specifications
Operating Temp: 0°C to 40°C
Operating Voltage: 230V AC 50Hz
Switch Rating: 230V AC 13 amp resistive
(3kW)
5 amp inductive
400W Filament Lighting
100W Low Energy or any
type of Fluorescent
Lighting
Conforms to
Directives: 73/23/EEC & 89/336/EEC
Not suitable for discharge lighting
(eg SON or Halide)
HELPLINE
020-8450-0515
or email [email protected]
For a product brochure please contact:
Timeguard Ltd.
Victory Park, 400 Edgware Road,
London NW2 6ND Tel: [phone]
or email [email protected]
A Group company
5 6
OPERATING INSTRUCTIONS
24 HOUR
PLUG-IN TIME
CONTROLLER
Cat. No TS800B
3 Year Guarantee
In the unlikely event of the product becoming faulty
due to defective material or manufacture within
3 years of the date of purchase, please return it to
your supplier in the first year with proof of purchase
and it will be replaced free of charge. During the
second and third years or any difficulty in the first
year telephone the helpline on 020 8450 0515
67-058-269
TS800B_Instrucs.indd 2TS800B_Instrucs.indd 2 14/1/08 10:47:0214/1/08 10:47:02

Important
This Timecontroller is recommended for
general domestic appliances up to 13 amp
resistive or 5 amp inductive rating. Certain
washing machines require the power to be
permanently connected and they cannot be
controlled by the TS800B. This is also true of
tumble dryers with push button start.
Note: Minimum setting interval =
15 minutes.
Minimum ON/OFF time between
settings = 30 minutes.
Specifications
Operating Temp: 0°C to 40°C
Operating Voltage: 230V AC 50Hz
Switch Rating: 230V AC 13 amp resistive
(3kW)
5 amp inductive
400W Filament Lighting
100W Low Energy or any
type of Fluorescent
Lighting
Conforms to
Directives: 73/23/EEC & 89/336/EEC
Not suitable for discharge lighting
(eg SON or Halide)
HELPLINE
020-8450-0515
or email [email protected]
For a product brochure please contact:
Timeguard Ltd.
Victory Park, 400 Edgware Road,
London NW2 6ND Tel: [phone]
or email [email protected]
A Group company
5 6
OPERATING INSTRUCTIONS
24 HOUR
PLUG-IN TIME
CONTROLLER
Cat. No TS800B
3 Year Guarantee
In the unlikely event of the product becoming faulty
due to defective material or manufacture within
3 years of the date of purchase, please return it to
your supplier in the first year with proof of purchase
and it will be replaced free of charge. During the
second and third years or any difficulty in the first
year telephone the helpline on 020 8450 0515
67-058-269
TS800B_Instrucs.indd 2TS800B_Instrucs.indd 2 14/1/08 10:47:0214/1/08 10:47:02