Tinkerine Studio Ditto Pro User manual

Make sure the printer is located
near an accessible power outlet.
Use a box cutter to
trim along the taped
edges and peel back
the outer box aps.
The DittoPro™ 3D Printer
can be too heavy to lift out
of the box by yourself. Ask
for help to prevent injury or
damages to the printer.
Open shipping box and remove the compartment lid.
1
Remove foam bracket and take out the printer and lament.
2Remove printer accessories from the compartment.
3
SD Card
USB Cable
Power Cable
Print Bed Clips x4
Glass Print Bed
Hex Wrench
DittoPro™ 3D Printer Filament Spool
Place the printer on a rm at surface.
5
Remove the printer and lament from the box.
4
Place the DittoPro™ 3D printer and PLA lament in
a moisture-free and low dust environment.
Store opened spools of lament in a sealed bag with
a desiccant packet.
KG
16.5

2x
Insert the male end of the power cord into an electrical socket.
2
Make sure the power switch on the printer is in the Off position ( O ).
1
Insert the female end into the power socket located on the back of the printer.
3
Turn on the printer by ipping the power switch to the On position ( I ).
4
6
TURNING ON THE PRINTER
INSTALLING THE FILAMENT
Extend the lament guide tube
from the retracted position.
1
Remove the lament spool from
the packaging and place it on
the spool holder.
2
Take the end of the lament
from the spool and insert it
into the guide tube.
3
Store the removed clips and reuse when
transporting the printing for shipping.
Remove the two gantry clips securing
the extruder by pushing down the tabs
on each end of the clips.
Make sure the spool will spin
clockwise as the lament
feeds into the guide tube.

Thread the lament through the guide tube. Push
the tensioner button down to make it easier to thread
the lament through the drive gear and into the hotend.
4Once the lament is inserted all the way down into
the hotend, insert the guide tube into the top of the
extruder cap.
5
STARTING THE PRINT BED CALIBRATION
From the main menu, turn the dial to scroll to Wizard.
Push down on the dial to select.
1Select the Bed Level option and follow the
on-screen instructions to level the printer’s bed level.
2
Place the glass print surface onto the bed with the
blue painter’s tape side facing upward. The tape
will act as an adhesion material for the plastic.
1With the clips provided in the kit, slide each clip on
to pinch the bed platform and glass print surface
together. Attach the clips onto the bed as shown.
2
WIZARD
Exit
Bed Level New Filament
TempPrint
MAIN
MENU
Status
Axis Wizard
Trim off the tip of the lament with a pair of scissors if you are having trouble feeding the lament into the hotend.
Replace any worn or damaged blue painter’s tape as needed to ensure that your prints stick properly during the
printing process.
INSTALLING THE PRINT BED

TECHNICAL SUPPORT
MAIN
TEST_PRINT.G
VASE.G
BRACELET.G
YOUR_PRINT.G
STARTING A PRINT
PRINTER REGISTRATION
From the main menu, turn the dial to scroll to Print.
Push down on the dial to select.
1Scroll down to the le you want to print and push
down again to start the print.
2
TempPrint
MAIN
MENU
Status
Axis Wizard
Whenever you begin a print, always check that the rst layer of the print is properly stuck onto the blue painter’s tape. A
properly leveled bed should have the extruded lament a bit squished and shouldn’t pop off the bed easily. While the
printer is performing the skirt nozzle purge, observe the deposited lament and make micro-adjustments with the thumb-
screw if necessary.
Visit our printer registration page to complete and submit the registration form to apply your Tinkerine Product Warranty.
Follow the instructions listed on the website to complete your production registration.
TOO CLOSE LEVELED TOO FAR
For technical assistance, please contact the Tinkerine Technical Support team:
• Email: [email protected]
• Phone: [phone]
http://warranty-registration.tinkerine.com