Tip Top Water SMART HC91L-UFD User manual

SMART Upflow Energy Saving Dispenser (Tri-Temp)
Model: HC91L-UFD
User Manual
Read this instruction manual before using the
appliance.
This appliance is intended to be used indoor only.
Please call our Service Department if
encounter any problems when using the
appliance.
Tel : [phone]
Fax : [phone]
Email ：[email protected]
Website ：www.tiptopwater.com.hk

IMPORTANT NOTES
1. Dispenser should be placed on a hard level surface. Leave at least 10cm behind the dispenser for
ventilation.
2. Place the dispenser in a dry and cool area and keep away from direct sunlight.
3. Unplug the power cord if the dispenser will not be used for a long time.
4. Do not modify the power plug or use an extension cord with the dispenser.
5. When the power cord is unplugged or the power supply to the dispenser is discontinued, wait for at
least 3 minutes before re-connecting the power.
6. When cleaning the dispenser, unplug the power cord and use a clean cloth with neutral washing to
wipe the surface of the dispenser. Do not spill the dispenser with water. Do not put the
dispenser in water.
7. Do not place dispensers or bottled water near expensive furniture, appliances or power sources as
water spill can cause serious damages. It is recommended to place the dispenser on a plastic mat.
Tip Top Water Group will not be responsible for claims against damages caused by water spill from
carboy bottle water drinking system.
GENERAL PRECAUTIONS
1. Should the condensing coil be covered by dust or foreign particles, clean the coil with a dry cloth.
2. We recommend the dispenser to be fully sanitized in every 9 months. Call our service department
for details.
3. If there is any problem with the dispenser, call our service department.
Tip Top Water Group shall not be liable for any conditions or damages resulting from accidents,
alterations, exposure to elements, misuse abuse or failure to follow our instructions with respect to
installation, cleaning, or maintenance. In case of any dispute, Tip Top Water Group’s determination
should be final.
! Caution ：Unplug the power cord before cleaning and/or inspecting the dispenser.
! Caution ：Hot water of this dispenser reaches 85°C, beware when using hot water.
! Warning ：If the power cord is damaged, you should call for service.
! Warning ：This dispenser is not recommended to be used by children, elderly or
any person in needed without accompanied and guidance by an adult.
! Warning ：Do not let children to play with the dispenser.

DISPENSER DIAGRAM
1. Hot Water Faucet (with safety lock)
2. Cold Water Faucet
3. Ice Water Faucet
4. LED Indicator
Red indicator = Hot Water Indicator
White Indicator = Empty Bottle Indicator
Orange Indicator = Power Indicator
Blue indicator = Ice Water Indicator
5. Spigot Light
6. Spigot
7. Drip Tray
8. Tube Connector
9. Water Tube (with adjustable length)
10. Door (pump will not operate if the door is not
closed properly)
11. Ice Water Switch
12. Fuse
13. Hot Water Switch
14. Power Code
15. Hot Water Drain (Caution: Beware of Hot Water)
16. Condenser

NOTES FOR INSTALLATION
1. Place a new water bottle next to the dispenser. Remove the label and sticker of the cap (no need to
tear the cap off). Open the door, adjust the stainless steel water tube to desire length. Insert the
water tube into the cap and push downward until the transparent membrane opens. Push the water
bottle inside the bottle storage compartment through the ramp. Close the door. (Please note the
pump cannot operate if the door is not closed properly.)
2. Connect the dispenser to the power supply. Dispenser would automatically start pumping water.
Press the THREE faucets one by one until water comes out from all three faucets. Switch on the
heating and cooling system by pressing hot water switch and ice water switch.
LED INDICATOR
Power
(Orange)
Off : Power Off
On : Power On
Cooling
(Blue)
Off : Cooling System is off
On : Cooling
Off : Cold water reaches desire temperature
Heating
(Red)
Off : Heating System is off
On : Heating
Off : Hot water reaches desire temperature
Change Bottle
(White)
Off : No need to change water
Flashing : No water in bottle, change water
SPECIFICATIONS
Power Supply
220V ~ 50Hz
Protective Type of
Anti-electric Shock
I
Rated Input (Heating)
500W
Rated Input (Cooling)
85W
Temperature
Ice: 7-10℃
Hot: 82-90℃
Refrigerant
R134a